SEARCH · Engineering Papers

Results for “CONTACT RESISTANCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Different Damp-Heat-Induced Series Resistance Degradation Behaviors in Fielded Crystalline Silicon Photovoltaic Modules Due to Difference in Bill of Materials

This case study investigates mono-crystalline silicon modules from underperforming portions of a utility-scale photovoltaic power plant. Field-collected I-V curves and electroluminescence imaging suggested that increased series resistance was a primary factor driving module degradation. Selected modules were removed from the field for further analysis, including incremental damp heat accelerated testing, which confirmed a progression in series resistance degradation. Two distinct cell degradation behaviors became apparent during the investigation. Cross-sectional scanning electron microscopy (with elemental analysis) and scanning spreading resistance microscopy identified key differences between the two degradation mechanisms, primarily grid finger width and contact resistance. Additionally, the study highlights the reliability implications of retest requirements in International Electrotechnical Commission 61215 for material changes and how they may have mitigated the degradation observed at this site.

14 SOLAR ENERGY↗

NASA NTRS1980

Advances in tunable diode laser technology

The improvement of long-term reliability, the purification of mode properties, and the achievement of higher-temperature operation were examined. In reliability studies a slow increase in contact resistance during room temperature storage for lasers fabricated with In-Au or In-Pt contacts was observed. This increase is actually caused by the diffusion of In into the surface layer of laser crystals. By using a three layered structure of In-Au-Pt or In-Pt-Au, this mode of degradation was reduced. In characterizing the mode properties, it was found that the lasers emit in a highly localized, filamentary manner. For widestripe lasers the emission occurs near the corners of the junction. In order to achieve single-mode operation, stripe widths on the order of 8-10 micrometers are needed. Also, it was found that room temperature electroluminescence is possible near 4.6 micrometers.

Lo, W.↗

NASA NTRS1994

The Anderson Current Loop

Four-wire-probe concept applied to electrical-resistance transducers. Anderson current loop is excitation-and-signal-conditioning circuit suitable for use with strain gauges, resistance thermometers, and other electrical-resistance transducers mounted in harsh environments. Used as alternative to Wheatstone bridge. Simplifies signal-conditioning problem, enabling precise measurement of small changes in resistance of transducer. Eliminates some uncertainties in Wheatstone-bridge resistance-change measurements in flight research. Current loop configuration makes effects of lead-wire and contact resistances insignificantly small. Also provides output voltage that varies linearly with change in gauge resistance, and does so at double sensitivity of Wheatstone bridge.

Anderson, Karl F.↗

DOE OSTI2025

Nm-scale electrical resistance imaging on CdTe by scanning spreading resistance microscopy

Local resistance imaging can provide information on nm-scale carrier distribution in semiconductor devices. Scanning spreading resistance microscopy (SSRM), an atomic force microscopy-based nm-scale resistance mapping technique, has been developed for carrier delineation in Si microdevices. We report on the development and validation of SSRM on CdTe materials, by testing on molecular beam epitaxy (MBE) grown CdTe films. The probe/CdTe contact resistance was suppressed sufficiently below sample's spreading resistance by pressing the probe into the sample with ∼mN contact force and applying a large sample/probe forward bias voltage (V s ), which was understood by analyzing current-voltage (I-V) involving a serially connected insulating top layer with underlying spreading resistance. The carrier concentration as deduced from the resistance measurement, using a single mobility value, is consistent with Hall measurement with a standard deviation of 14% based on a set of MBE films with carrier concentrations in the range of 10 15 –10 16 /cm 3 . The doping polarity was readily identified by flipping V s polarity, where the resistance with reverse V s is orders of magnitude larger than forward V s . While focusing on the SSRM technique validation, we also show an example on an As-doped Cd(Se,Te) polycrystalline thin film of a high-performance CdTe solar cell, which illustrates the local resistance nonuniformity with up to two orders of magnitude differences, indicating if local mobility is roughly constant, local carrier concentration can have significant nonuniformity.

14 SOLAR ENERGY↗

DOE OSTI2023

Performance and durability of electrically conductive tape for shingled Si heterojunction technology cells

We report electrically conductive tape (ECT) was characterized and used to assemble shingled cell strings at low temperature to achieve high reliability Pb- and Ag-free interconnections. The volume resistivity for two considered ECTs are 0.13 ± 0.06 mΩ·cm and 0.47 ± 0.20 mΩ·cm and specific contact resistances, 6.85± 2.00 mΩ·cm 2 and 6.30 ± 0.37 mΩ·cm 2 using the emerging IEC 62788-8-1 Technical Specification for assessment of electrically conductive adhesives (ECA). Durability and performance of the technology in glass–glass mini modules were evaluated with temperature cycling, damp heat testing, and combined-accelerated stress testing (CAST). Through temperature cycling (-40°C to 85°C) applying five times the mini module short-circuit current in forward bias and in the multi climate CAST protocol, there was negligible degradation of fill factor after replacing connectors at the modules' cable leads; however, CAST resulted in short circuit current loss attributed to degradation in light collection by the cells, not the ECT. The IEC 61215-2 85°C, 85% relative humidity damp heat testing showed susceptibility of the HJT cells to effects of humidity in the electroluminescence intensity around the module perimeter that degraded power performance by 4% (relative). Contrasting the IEC 61215-2 qualification testing-based damp heat testing with CAST, factors such as the optical stress of CAST may precipitate the degradation of the modules whereas the humidity levels and duration of IEC 61215-2 damp heat testing may lead to excessive levels of humidity diffused into the modules, potentially resulting in degradation that is unrepresentative of the field.

14 SOLAR ENERGY↗

DOE OSTI2025

Graphene oxide gluing layer enabling macroscale tribology applications of pristine graphene

In recent studies of two-dimensional (2D) nanomaterial-based solid lubricants, the importance of durability has been emerging for real engineering-scale applications. To achieve this, a transfer layer formation is essential to prevent the wear of the mechanical systems. However, it has been challenging for pristine graphene (PG) to induce a material transfer due to chemical inertness. In this study, we suggest an easy-to-process strategy to promote the huge material transfer of the PG onto the counterpart contacting material. We utilized graphene oxide (GO) as a gluing layer between the PG film and the counterpart contact surface to realize the superior tribological performance. The high interaction energy of the GO from its functional groups makes a contribution to the material transfer of PG, which is unveiled by a systematic analysis of the counterpart contact surface and the wear track. The huge solid transfer layer not only makes a wear-resistant contact interface between the transfer layer and the underlying film by densification and oxidation, but also reduces surface interaction energies, finally resulting in a significant improvement in durability.

graphene oxide (GO)↗

DOE OSTI2024

High temperature stability of regrown and alloyed Ohmic contacts to AlGaN/GaN heterostructure up to 500 °C

This Letter reports the stability of regrown and alloyed Ohmic contacts to AlGaN/GaN-on-Si high electron mobility transistors (HEMTs) for high temperature applications up to 500 °C. Transfer length method (TLM) measurements from 25 to 500 °C in air show that the regrown contacts appear to be stable up to 500 °C during short term (approximately 1 h) testing, while alloyed contacts appear to decrease in contact resistance from 300 to 500 °C though increases in the error bounds due to increase sheet resistance make it difficult to conclude definitely. Additionally, longer term testing shows both technologies remain stable at least up to 48 h at 500 °C, after which the large increase in sheet resistance makes the measurement uncertainty too large to conclude definitively. Advanced microscopy images indicate both the regrown and alloyed contact regions remain structurally intact after prolonged high temperature exposure with no visible degradation in crystallinity or metal composition.

Physics↗

NASA NTRS1975

Glass-Si heterojunction solar cells

Experimental studies and models for In2O3/Si and SnO2/N-Si solar cells are considered for their suitability in terrestrial applications. The silicon is the active material, and the glass serves as the window to solar radiation, an antireflection coating of the Si, and a low resistance contact. Results show that amorphous windows or layers suppress photocurrent. The interfacial SiO2 layer suppresses photocurrent and increases series resistance. Suppression increases with illumination.

Anderson, R. L.↗

NASA NTRS1991

The influence of interstitial Ga and interfacial Au2P3 on the electrical and metallurgical behavior of Au-contacted III-V semiconductors

The effect of introducing a very small amount of Ga into Au-contacted InP on the behavior of that contact system was investigated. It was found that Ga affected both the metallurgical and the electrical behavior of the system. It is shown that Ga atoms in the interstices of the Au lattice prevent the solid-state reactions that normally take place between Au and InP during contact sintering and cause an order of magnitude reduction in the specific contact resistivity. It is also shown that the presence of Ga affects the reactions of GaP and GaAs with Au contacts.

Weizer, Victor G.↗

NASA NTRS2026

Development and Validation of a High-Vacuum Thermal Conductivity Testbed for Aerospace Interface Materials

Thermal Interface Materials (TIMs) are critical components in spacecraft thermal management systems, where thermal performance is strongly influenced by vacuum conditions, interface contact resistance, and layered metallic joint behavior. However, manufacturer-reported thermal conductivity values are often derived under idealized conditions and may not accurately represent performance within operational aerospace applications. To address this limitation, the Testbed for Advanced Interface Materials in Vacuum (TAIMV) was developed as a modular vacuum-compatible thermal conductivity characterization platform capable of evaluating aerospace-relevant TIM configurations under both ambient and high-vacuum environments. The testbed was derived from the ASTM C1044-16 guarded hot plate methodology and incorporates interchangeable layers of stainless steel coupon geometries, independently controlled main and guard heaters, embedded resistance temperature detectors (RTDs), thermocouples, multi-layer insulation (MLI), and a temperature-controlled cold plate to characterize through-thickness thermal gradients across layered interfaces. In the current configuration, interface compression is limited to the nominal contact pressure generated by the experimental stack assembly. Initial experimental campaigns were conducted at ambient pressure and below 1×10-5 torr for vacuum cases using multiple interface materials including Braycote 601EF and Krytox-based greases across a range of thermal operating conditions. In parallel, a coupled numerical Python thermal model was developed to predict temperature distribution throughout the stack while accounting for conduction, radiation, and parasitic heat transfer pathways and effective interface resistance effects. Experimental measurements and numerical predictions showed consistent thermal trends across multiple operating conditions and environmental states. Results also revealed measurable differences between ambient and vacuum thermal behavior, demonstrating the importance of interface resistance, parasitic heat transfer mechanisms, and stack geometry in determining effective thermal performance within layered thermal interfaces. The presented work establishes a foundation for future thermal model correlation efforts and expanded characterization of aerospace thermal interface materials under representative environmental conditions. Future work will focus on the integration of a load cell system to enable controlled pressure-dependent characterization of thermal interface materials under compressive loading. This capability will allow investigation of the influence of contact pressure on effective thermal conductivity, interface resistance, and thermal performance within layered aerospace thermal interfaces under representative operational conditions.

Thermal Development Testing↗

DOE OSTI2020

Thermally Driven Interfacial Degradation between Li 7 La 3 Zr 2 O 12 Electrolyte and LiNi 0.6 Mn 0.2 Co 0.2 O 2 Cathode

Solid-state batteries offer higher energy density and enhanced safety compared to the present lithium-ion batteries using liquid electrolytes. A challenge to implement them is the high resistances, especially at the solid electrolyte interface with the cathode. Sintering at elevated temperature is needed in order to get good contact between the ceramic solid electrolyte and oxide cathodes and thus to reduce contact resistances. Many solid electrolyte and cathode materials react to form secondary phases. It is necessary to find out which phases arise as a result of interface sintering and evaluate their effect on electrochemical properties. Herein, we assessed the interfacial reactions between LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) and Li 7 La 3 Zr 2 O 12 (LLZO) as a function of temperature in air. We prepared model systems by depositing thin-film NMC622 cathode layers on LLZO pellets. The thin-film cathode approach enabled us to use interface-sensitive techniques such as X-ray absorption spectroscopy in the near-edge as well as the extended regimes and identify the onset of detrimental reactions. We found that the Ni and Co chemical environments change already at moderate temperatures, on-setting from 500 °C and becoming especially prominent at 700 °C. By analyzing spectroscopy results along with X-ray diffraction, we identified Li 2 CO 3 , La 2 Zr 2 O 7 , and La(Ni,Co)O 3 as the secondary phases that formed at 700 °C. The interfacial resistance for Li transfer, measured by electrochemical impedance spectroscopy, increases significantly upon the onset and evolution of the detected interface chemistry. Our findings suggest that limiting the bonding temperature and avoiding CO 2 in the sintering environment can help to remedy the interfacial degradation.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Measuring the maximum capacity and thermal resistances in phase-change thermal storage devices

Thermal energy storage can increase the efficiency of the electric grid by adding flexibility to thermal systems. The value of thermal storage is a function of its energy and power density, which are driven by the capacity and thermal resistances in the storage device. Measuring these properties in-situ at the device level is an important step to understanding the performance and improving the design of thermal storage systems. Here, we present methods to measure the total capacity and thermal resistances in heat exchangers with integrated phase change materials. These methods are demonstrated on two thermal storage devices - a 570-kWh ice-based storage tank and a 0.35-kWh graphite-tetradecane composite device. The results show how thermal resistances evolve with the state of charge and discharge rate in these devices and quantify the impact of applied pressure on the contact resistance in composite phase change material heat exchangers. The proposed method allows for easy comparison between different systems and provides information on the thermal bottlenecks limiting performance. Ultimately, these measurements will allow designers to make robust, high-performance thermal storage devices for next-generation thermal systems.

25 ENERGY STORAGE↗

DOE OSTI2024

Tunable amorphous carbon films formed on ultralow wear, Pt–Au alloys

The mechanocatalytic formation of carbonaceous films at the interface between sliding metallic contacts is simultaneously advantageous for reducing friction and adhesion in several tribological applications and detrimental for electrical contacts as they can induce device failure by increasing the contact resistance. Yet, remarkably little is still known about the chemistry, structural and mechanical properties, and tunability of these interfacial layers. In this study, we performed contact pressure-dependent tribological experiments in dry nitrogen containing trace organics on four, nanocrystalline Pt–Au alloys ([Au] from 0 at.% to 10 at.%) – a promising class of alloys for ultralow wear and electrical contact applications. The ex-situ, multi-technique characterization results did not only provide insights into the chemical nature and mechanical behavior of the mechanocatalytic, carbon-rich films formed on Pt–Au surfaces, but also revealed the interplay between catalytic and mechanochemical tribofilm formation controlled by the composition-dependent electronic structure of the Pt–Au substrate and the applied contact pressure. The results of this work provide guidelines for tailoring nanocrystalline alloys to control their mechanocatalytic activity on the basis of variations of the alloy mechanical properties and element's electronic structure with the alloy stoichiometry.

AFM↗

NASA NTRS1987

InP based solar cells for space application: Reduction of external losses

Although InP-based solar cells have considerable potential for space applications, it is necessary to improve efficiencies to around the level of GaAs or Si cells before their excellent radiation resistance can be regarded as a dominant advantage. The authors concentrate on indium-tin-oxide/InP cells, presenting data relating to reduction of the contact resistance of the rear surface metallization, reduction of reflectance losses by choosing indium-tin-oxide deposition conditions to give specific optical properties, and reduction of losses associated with the grid. Simultaneous optimization of all of these has led to improved values of Jsc. For devices of approximately 1 cm2 in area, the largest Jsc achieved to date is 28.1 mA/aq cm (AM1.5, SERI/NASA direct normal spectrum, 25 C, total area, 100 mW/sq cm). For this particular cell, the equivalent AM0 value of Jsc was 34.6 mA/sq cm, which appears to be the largest reported for any InP-based cell.

Wu, X.↗

DOE OSTI2025

Porous Interlayers that Getter Surface-Segregating Species for Improved Silver Wetting, Adhesion, and Electrical Contact on Stainless Steel SOFC Components

Here, porous nickel interlayers or porous platinum interlayers were shown to promote the wetting, spreading, and adhesion of silver on alumina-forming ferritic stainless steel (AFFSS) and chromia-forming ferritic stainless steel (CFFSS). These interlayers resulted in dense, crack-free AFFSS|Ag-Ni|CFFSS and AFFSS|Ag-Pt|CFFSS braze joints that, after 300 h in 650 °C air, displayed shear strengths up to 70 MPa similar to, or larger than, those of AFFSS|Ag-CuO|CFFSS or AFFSS|Ag|CFFSS joints subjected to identical treatment. Similarly, after exposure to 25 cycles of (50 switches between) 12 h of 650 °C air and 12 h of 650 °C 4%H 2 –96%N 2 , AFFSS|Ag-Ni|CFFSS and AFFSS|Ag-Pt|CFFSS braze joints displayed shear strengths significantly larger than those of AFFSS|Ag-CuO|CFFSS or AFFSS|Ag|CFFSS joints subjected to identical treatment. In addition, nickel and platinum were found to chemically getter surface-segregating steel constituents, particularly Al from the AFFSS. As a result, Ag-Ni and Ag-Pt electrical contact resistances on AFFSS and CFFSS substrates were several orders of magnitude lower than those of conventional Ag-CuO reactive air brazes or Heraeus C8710 Ag contact pastes. Together, these results suggest that Ag-Pt and especially Ag-Ni may be useful for the fabrication of durable joints, seals, and/or electrical contacts in electrical/electrochemical devices exposed to high temperatures and/or variable oxygen partial pressure environments.

36 MATERIALS SCIENCE↗

NASA NTRS2002

The Electrical and Thermal Conductivity of Woven Pristine and Intercalated Graphite Fiber-Polymer Composites

A series of woven fabric laminar composite plates and narrow strips were fabricated from a variety of pitch-based pristine and bromine intercalated graphite fibers in an attempt to determine the influence of the weave on the electrical and thermal conduction. It was found generally that these materials can be treated as if they are homogeneous plates. The rule of mixtures describes the resistivity of the composite fairly well if it is realized that only the component of the fibers normal to the equipotential surface will conduct current. When the composite is narrow with respect to the fiber weave, however, there is a marked angular dependence of the resistance which was well modeled by assuming that the current follows only along the fibers (and not across them in a transverse direction), and that the contact resistance among the fibers in the composite is negligible. The thermal conductivity of composites made from less conductive fibers more closely followed the rule of mixtures than that of the high conductivity fibers, though this is thought to be an artifact of the measurement technique. Electrical and thermal anisotropy could be induced in a particular region of the structure by weaving together high and low conductivity fibers in different directions, though this must be done throughout all of the layers of the structure as interlaminar conduction precludes having only the top layer carry the anisotropy. The anisotropy in the thermal conductivity is considerably less than either that predicted by the rule of mixtures or the electrical resistivity.

Gaier, James R.↗

DOE OSTI2022

Measurement of Resistance, Porosity, and Water Contact Angle of Porous Transport Layers for Low-Temperature Electrolysis Technologies

The porous transport layer is an important component of low-temperature electrolysis devices, such as proton exchange membrane water electrolyzers or anion exchange membrane water electrolyzers. PTLs have significant influence on the cell performance as their bulk resistance can impact the ohmic resistance, their contact resistance can impact electrode performance, and their structure can impact the liquid flow to the cell, which could cause mass-transport losses. In order to improve cell performance, optimization of the PTL is critical. Standardized protocols should be utilized to adequately compare PTLs being developed from different institutions. This method will detail a standardized protocol for measuring the resistance of the PTL using a four-wire setup and will also detail a process for measuring the porosity and water contact angle of the PTL using capillary flow porometry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1988

Effect of length of chopped pristine and intercalated graphite fibers on the resistivity of fiber networks

Samples of Amoco P-100 fibers were chopped to lengths of 3.14, 2.53, 1.90, 1.27, 0.66 mm, or milled for 2 hours. The two-point resistivity of compacts of these fibers were measured as a function of pressure from 34 kPa to 143 MPa. Samples of each fiber length were intercalated with bromine at room temperature and similarly measured. The low pressure resistivity of the compacts decreased with increasing fiber length. Intercalation lowered the resistivity of each of the chopped length compacts, but raised the resistivity of the milled fiber compacts. Bulk resistivity of all samples decreased with increasing pressure at similar rates. Even though fiber volumes were as low as 5 percent, all measurements exhibited measurable resistivity. A greater change with pressure in the resistance was observed for shorter fibers than for longer, probably an indication of tighter fiber packing. Intercalation appeared to have no effect on the fiber to fiber contact resistance.

Gaier, James R.↗