Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMBUSTION CONTROL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Emissions from premixed charge compression ignition (PCCI) combustion and affect on emission control devices

A light-duty diesel engine has been operated in advanced combustion modes known generally as premixed charge compression ignition (PCCI). The emissions have been characterized for several load and speed combinations. Fewer NO{sub x} and particulate matter (PM) emissions are produced by PCCI, but higher CO and hydrocarbon (HC) emissions result. In addition, the nature of the PM differs from conventional combustion; the PM is smaller and has a much higher soluble organic fraction (SOF) content (68% vs. 30% for conventional combustion). Three catalyst technologies were studied to determine the affects of HECC on catalyst performance; the technologies were a lean NO{sub x} trap (LNT), diesel oxidation catalyst (DOC), and diesel particulate filter (DPF). The LNT benefited greatly from the reduced NO{sub x} emissions associated with PCCI. NO{sub x} capacity requirements are reduced as well as overall tailpipe NO{sub x} levels particularly at low load and temperature conditions where regeneration of the LNT is difficult. The DOC performance requirements for PCCI are more stringent due to the higher CO and HC emissions; however, the DOC was effective at controlling the higher CO and HC emissions at conditions above the light-off temperature. Below light-off, CO and HC emissions are problematic. The study of DPF technology focused on the fuel penalties associated with DPF regeneration or 'desoot' due to the different PM loading rates from PCCI vs. conventional combustion. Less frequent desoot events were required from the lower PM from PCCI and, when used in conjunction with an LNT, the lower PM from less frequent LNT regeneration. The lower desoot frequency leads a {approx}3% fuel penalty for a mixture of PCCI and conventional loads vs. {approx}4% for conventional only combustion.

33 ADVANCED PROPULSION SYSTEMS↗

Autoignition behavior of a full boiling-range gasoline: Observations in RCM and GCI engine environments

The understanding of, and capability to modulate fuel autoignition behavior are important aspects towards the development of advanced, low temperature combustion (LTC) engine concepts, which have potential to significantly increase engine efficiency while at the same time addressing emissions concerns. Proper combustion phasing and control of heat release rates via, for instance, multiple injections and exhaust gas recirculation, are significant challenges that can vary with fuel composition. Overall reactivity, which is a strong function of the in-cylinder temperature and pressure, is a prime driver for regulating combustion timing, while preliminary exothermicity, in the form of low- and intermediate-temperature heat release (LTHR, ITHR) can inhibit, or facilitate operational success, e.g., control combustion phasing. Here, there are still gaps in understanding these features and how they interact with needs of advanced combustion engines, and how practical fuels can be rated for the new challenges of LTC engines.

42 ENGINEERING↗

Space Shuttle Orbiter engine main combustion chamber cooling and life

A reusable life requirement of 100 missions is met by controlling the combustion chamber hot-gas wall temperature and strain levels. Maximum life, maximum performance, and minimum engine weight are attained through a descriptive parametric assessment of the regenerative cooling circuit, combustor length, contraction area ratio, and coolant passage geometry. Life is categorized by low-cycle fatigue and creep-stress rupture. Relationships are developed to determine the impact of heat transfer rate, thermal strain level, and geometric influence parameters on life. It is empirically shown that a throat heat flux of 100 Btu/sq in./sec can be accommodated.

Cook, R. T.↗

Injection Principles from Combustion Studies in a 200-Pound-Thrust Rocket Engine Using Liquid Oxygen and Heptane

The importance of atomizing and mixing liquid oxygen and heptane was studied in a 200-pound-thrust rocket engine. Ten injector elements were used with both steel and transparent chambers. Characteristic velocity was measured over a range of mixture ratios. Combustion gas-flow and luminosity patterns within the chamber were obtained by photographic methods. The results show that, for efficient combustion, the propellants should be both atomized and mixed. Heptane atomization controlled the combustion rate to a much larger extent than oxygen atomization. Induced mixing, however, was required to complete combustion in the smallest volume. For stable, high-efficiency combustion and smooth engine starts, mixing after atomization was most promising.

Heidmann, M. F.↗

Status and perspectives of municipal solid waste incineration in China: A comparison with developed regions

Highlights: • Questions about the applicability, technical status, and future of MSW incineration in China are answered. • Comparison involves China, EU, U.S., Japan, South Korea, and Taiwan area. • MSW incineration is not out of date around the world. • The structure of MSW incineration technologies is changing in China. • Perspectives and suggestions are given for the compliance with the emission standard. - Abstract: With the rapid expansion of municipal solid waste (MSW) incineration, the applicability, technical status, and future improvement of MSW incineration attract much attention in China. This paper aims to be a sensible response, with the aid of a comparison between China and some representative developed regions including the EU, the U.S., Japan, South Korea, and Taiwan area. A large number of up-to-date data and information are collected to quantitatively and impartially support the comparison, which covers a wider range of key points including spatial distribution, temporal evolution, technologies, emissions, and perspectives. Analysis results show that MSW incineration is not an outdated choice; however, policy making should prevent the potentially insufficient utilization of MSW incinerators. The structure of MSW incineration technologies is changing in China. The ratio of plants using fluidized bed is decreasing due to various realistic reasons. Decision-makers would select suitable combustion technologies by comprehensive assessments, rather than just by costs. Air pollution control systems are improved with the implementation of China’s new emission standard. However, MSW incineration in China is currently blamed for substandard emissions. The reasons include the particular elemental compositions of Chinese MSW, the lack of operating experience, deficient fund for compliance with the emission standard, and the lack of reliable supervisory measures. Some perspectives and suggestions from both technical and managerial aspects are given for the compliance with the emission standard. This paper can provide strategic enlightenments for MSW management in China and other developing countries.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Submerged combustion melting processes for producing glass and similar materials, and systems for carrying out such processes

Processes of controlling submerged combustion melters, and systems for carrying out the methods. One process includes feeding vitrifiable material into a melter vessel, the melter vessel including a fluid-cooled refractory panel in its floor, ceiling, and/or sidewall, and heating the vitrifiable material with a burner directing combustion products into the melting zone under a level of the molten material in the zone. Burners impart turbulence to the molten material in the melting zone. The fluid-cooled refractory panel is cooled, forming a modified panel having a frozen or highly viscous material layer on a surface of the panel facing the molten material, and a sensor senses temperature of the modified panel using a protected thermocouple positioned in the modified panel shielded from direct contact with turbulent molten material. Processes include controlling the melter using the temperature of the modified panel. Other processes and systems are presented.

33 ADVANCED PROPULSION SYSTEMS↗

Method of transient control for robust enrichment operation in low temperature combustion engine

A method of transient control for enrichment operation in a low-temperature combustion engine. The method includes determining if a current mode of the low-temperature combustion (LTC) engine is a positive valve overlap (PVO) mode. Determining if a previous mode of the LTC engine was also the PVO mode when the current mode is the PVO mode, wherein the previous mode is immediately prior to the current mode. Determining if the previous mode of the LTC engine was a negative valve overlap (NVO) mode when the previous mode was not the PVO mode. Initiating a predetermined enrichment PVO mode for the LTC engine based on the previous mode of the LTC engine. The predetermined enrichment PVO mode includes initiating a deep enrichment PVO mode, when the previous mode of the LTC engine was the NVO mode, and initiating a shallow enrichment PVO mode, when the previous mode of the LTC engine was not the NVO mode.

Yun, Hanho↗

Oxycombustion in transport oxy-combustor

A pressurized transport oxy-combustor with different configurations is disclosed. Substantially pure oxygen is fed to the transport oxy-combustor under pressure to combust fossil fuels, generating steam for power generation. The end product is the flue gas containing substantially pure CO2 after moisture condensation. The low excess oxygen necessary to achieve complete combustion in the combustor is scavenged by adding another fuel so that substantially all oxygen fed to the combustor is completely consumed. The capability to operate the transport oxy-combustor as a circulating fluidized bed combustor at very high solids circulation rates makes it unnecessary to use recycled CO2 or flue gas as a means to moderate and control the combustion temperature. The temperature in the combustor is effectively controlled by relatively cooler circulating solids that enter the combustion zone. A small amount of CO2 is recycled for aeration and to convey solids fuel to the combustor.

Vimalchand, Pannalal↗

Low Temperature Combustion Exploration with Negative Valve Overlap

Progressively stringent emission regulations and increasing regulatory demands on fuel economy have led to advanced combustion development. Low temperature combustion (LTC), specifically homogenous charge compression ignition (HCCI), is a promising technology for reducing exhaust emissions and improving efficiency. However, its operating range is limited to low load without boosting and EGR, due to low volumetric efficiency and high pressure rise rates. In addition, effectively controlling the combustion phasing is another challenge in realizing the associated combustion gains. In this work, advanced valve control mechanisms known as continuously variable valve duration (CVVD) and continuously variable valve timing (CVVT) were used for both intake and exhaust valvetrains to enable negative valve overlap (NVO) for trapping hot exhaust residuals and to promote multipoint simultaneous ignition. Heat release phasing was controlled by varying the fueling scheme and by adjusting the amount of NVO. Parametric studies on valve timing and duration, fueling strategy, lambda, spark assist, etc., were carried out first. Afterwards the LTC strategy was proposed and then LTC operation was explored at different engine speeds. Various approaches for extending load limits were summarized and discussed. Finally, combustion performance was compared to that of spark ignition combustion, demonstrating the combustion gains of LTC.

02 PETROLEUM↗

Variable-speed supercharger for highly diluted internal combustion engines

An engine control system includes an internal combustion engine including a plurality of cylinders. An intake manifold is connected to the internal combustion engine. An exhaust manifold is connected to the internal combustion engine. A supercharger is connected to an air intake passage and the intake manifold and includes a variable speed drive. A throttle valve is disposed in the air intake passage. An exhaust passage is in connection with the exhaust manifold. A passive selective catalytic reduction catalyst system is in communication with the exhaust passage. An exhaust gas recirculation passage is in communication with the exhaust passage and the air intake passage and includes an exhaust gas recirculation valve. A controller controls the variable speed drive of the supercharger and the throttle valve and the exhaust gas recirculation valve based upon engine conditions.

42 ENGINEERING↗

Oxygen-diffusion limited metal combustions in Zr, Ti, and Fe foils: Time- and angle-resolved x-ray diffraction studies

The transient phase and chemical transformations of diffusion controlled metal combustions in bulk Zr, Ti, and Fe foils have been investigated, in situ, using novel time- and angle-resolved x-ray diffraction (TARXD). The TARXD employs monochromatic synchrotron x-rays and a fast-rotating diffracted beam chopper resolving the diffraction image temporally in time-resolution of {approx}45 {mu}s along the azimuth on a 2D pixel array detector. The metal foil strips (10-25 {mu}m in thickness) are ignited using a pulsed electrical heating with a typical heating rate of {approx}10{sup 6} K/s. The x-ray results indicate that the combustion occurs in molten metals, producing a wide range of stoichiometric solid oxides. It reflects an enhanced oxygen solubility and mobility of molten metals with respect to those of solid metals. However, the initial oxides formed are mainly oxygen-deficient metal oxides of ZrO, TiO, and FeO/Fe{sub 3}O{sub 4} - the lowest suboxides stable at these high temperatures. These transition metal monoxides further react with unreacted molten metals, yielding the secondary products of Zr{sub 3}O, Ti{sub 3}O, and Ti{sub 2}O - but not in FeO/Fe{sub 3}O{sub 4}. On the other hand, the higher stoichiometric oxides of ZrO{sub 2} and TiO{sub 2} are formed in the later time only on the metal surface. These results clearly indicate that the combustion process of metal strips is diffusion limited and strongly depends on the solubility and diffusivity of oxygen into molten metals. The time-resolved diffraction data reveals no evidence for metal oxidation in solids, but a series of temperature-induced polymorphic phase transitions. The dynamic thermal expansibility of Fe measured in the present fast heating experiments is similar to those in static conditions (3.3*10{sup -5}/K vs 3.5*10{sup -5}/K for {alpha}-Fe and 6.5*10{sup -5}/K versus 7.0*10{sup -5}/K for {gamma}-Fe).

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Free-radicals aided combustion with scramjet applications

Theoretical and experimental investigations aimed at altering 'nature-prescribed' combustion rates in hydrogen/hydrocarbon reactions with (enriched) air are presented. The intent is to anchor flame zones in supersonic streams, and to ensure proper and controllable complete combustion in scramjets. The diagnostics are nonintrusive through IR thermograms and acoustic emissions in the control and free-radicals altered flame zones.

Yang, Yongsheng↗

Symposium (International) on Combustion, 19th, Technion Israel Institute of Technology, Haifa, Israel, August 8-13, 1982, Proceedings

Topics discussed are related to elementary reactions, reaction mechanisms and modeling, laminar flames, flame chemistry, turbulent reacting shear flows, turbulent premixed flames, turbulent combustion measurements, continuous combustors, detonation, detonation and explosion, heterogeneous detonation, propellant combustion, fire-ignition and thermal degradation, fire-flame spread and burning, fire-modeling, spray combustion, and droplet combustion. Coal combustion kinetics and mechanisms are considered along with coal combustion mechanisms and pyrolysis, coal combustion techniques, NOx in coal combustion, gaseous pollutants, soot and PAH, soot and inorganic pollutants, I.C. engine combustion, and ignition and extinction. Attention is given to intricate paths and simple steps in chemical kinetics and combustion, the formation of polycyclic aromatic hydrocarbons by combustion, turbulent flame structure and speed in spark ignition engines, and unresolved problems in SOx, NOx, and soot control in combustion.

Source record↗

Emissions Overview

The Emissions Reduction Project is working in close partnership with the U.S. aircraft engine manufacturers and academia to develop technologies to reduce NO, emissions by 70 percent over the LTO cycle from 1996 ICAO standards with no increase in other emission constituents (carbon monoxide, smoke, and unburned hydrocarbons) and with comparable NO, reduction during cruise operations. These technologies cannot impact the overall combustor and fuel delivery system operability, affordability or maintainability. These new combustion concepts and technologies will include lean burning combustors with higher operating gas temperatures and pressures, fuel staging, ceramic matrix composite material liners with reduced cooling air and possibly advanced controls. Improved physics-based analysis tool will be developed and validated and some longer term technologies that are more revolutionary will be assessed. These improved computational codes will provide improved design tools to increase design confidence and cut the development time to achieve major reductions in NO, emissions. Longer term, revolutionary technologies like active combustion controls, combustion from a large array of micro-injectors, electrostatic fuel injectors, fuel additives and others will be investigated and assessed through proof-of-concept testing.

Rohde, John↗

Combustion of solid carbon rods in zero and normal gravity

In order to investigate the mechanism of carbon combustion and to assess the importance of gravitational induced convection on the process, zero and normal gravity experiments were conducted in which spectroscopic carbon rods were resistance ignitied and burned in dry oxygen environments. In the zero-gravity drop tower tests, a blue flame surrounded the rod, showing that a gas phase reaction in which carbon monoxide was oxidized to carbon dioxide was taking place. The ratio of flame diameter to rod diameter was obtained as a function of time. It was found that this ratio was inversely proportional to both the oxygen pressure and the rod diameter. In the normal gravity tests, direct mass spectrometric sampling was used to measure gas phase concentrations. The gas sampling probe was positioned near the circumference of a horizontally mounted 0.615 cm diameter carbon rod, either at the top or at angles of 45 deg to 90 deg from the top, and yielded concentration profiles of CO2, CO, and O2 as a function of distance from the surface. The mechanism controlling the combustion process was found to change from chemical process control at the 90 deg and 45 deg probe positions to mass transfer control at the 0 deg probe position at the top of the rod. Under the experimental conditions used, carbon combustion was characterized by two surface reactions, 2C + O2 yields 2CO and CO2 + C yields 2CO, and a gas phase reaction, 2CO + O2 yields 2CO2.

Spuckler, C. M.↗

Investigation of near-field jet stability of a single-hole injector based on fast X-ray phase contrast imaging and image feature matching

Fuel spray is very effective in controlling the combustion process to improve engine performance and reduce emissions. Understanding the spray unstability during the injection process is of importance to improve the control of spray characteristics and engine operation. In this study, near-field biodiesel jets were recorded using fast X-ray phase contrast imaging and the flow features inside the jet were extracted using Speeded Up Robust Features (SURF) method. Here, the image similarity by feature matching was successfully used to represent the near-field jet stability. Based on the jet stability, an injection process can be divided into five stages: an unstable stage at needle opening, a partially stable transition stage at needle opening, a stable stage, a stable transition stage at needle closing and an unstable stage at needle closing. The ranges of needle lift for five stages were also determined. The jet unstability is highly related to the cavitation formation and gas purging process during needle opening. The variation of stable jet feature is dependent on the needle lift at needle closing. Higher needle lift for the similar jet feature at needle opening indicates a hydraulic delay compared to needle closing. Finally, the possible reasons of jet feature formation and feature detection used on the multi-hole injector are discussed.

33 ADVANCED PROPULSION SYSTEMS↗

Development of an Atomization Methodology for Spray Combustion

In liquid rocket propulsion, the knowledge and the understanding of liquid-gas interfacial phenomena are very important. This is important for predicting the onset of cavitation occurring in swirl injection elements used in STME, as well as atomization processes in shear-induced injectors (co-axial) and impinging injector elements. From the fact that all the physical processes including droplet size distribution, droplet dispersion, mixing and combustion are controlled by atomization processes, it is expected that the successful incorporation of the volume of fraction (VOF) will greatly enhance the analytical capability of predicting spray combustion processes in liquid-fueled engines. In this paper, a methodology is developed to define and track interfaces between two fluids in non-orthogonal, body-fitted grids using a single fractional volume of fluid (VOF) variable to describe the distribution of the liquid phase in a gas-liquid flow field. This method was implemented in a mature CFD code MAST (Multiphase All-Speed Transient) utilizing the general PISO-C algorithm. For the preliminary study on the analysis of spray combustion and tracking of the interface between two phases, we will report on the progress of the simulation of the instability on the liquid column; the surface wave instability and the droplet breakup from the liquid surface.

Seung, S. P.↗

Effects of Buoyancy on Laminar, Transitional, and Turbulent Gas Jet Diffusion Flames

Gas jet diffusion flames have been a subject of research for many years. However, a better understanding of the physical and chemical phenomena occurring in these flames is still needed, and, while the effects of gravity on the burning process have been observed, the basic mechanisms responsible for these changes have yet to be determined. The fundamental mechanisms that control the combustion process are in general coupled and quite complicated. These include mixing, radiation, kinetics, soot formation and disposition, inertia, diffusion, and viscous effects. In order to understand the mechanisms controlling a fire, laboratory-scale laminar and turbulent gas-jet diffusion flames have been extensively studied, which have provided important information in relation to the physico-chemical processes occurring in flames. However, turbulent flames are not fully understood and their understanding requires more fundamental studies of laminar diffusion flames in which the interplay of transport phenomena and chemical kinetics is more tractable. But even this basic, relatively simple flame is not completely characterized in relation to soot formation, radiation, diffusion, and kinetics. Therefore, gaining an understanding of laminar flames is essential to the understanding of turbulent flames, and particularly fires, in which the same basic phenomena occur. In order to improve and verify the theoretical models essential to the interpretation of data, the complexity and degree of coupling of the controlling mechanisms must be reduced. If gravity is isolated, the complication of buoyancy-induced convection would be removed from the problem. In addition, buoyant convection in normal gravity masks the effects of other controlling parameters on the flame. Therefore, the combination of normal-gravity and microgravity data would provide the information, both theoretical and experimental, to improve our understanding of diffusion flames in general, and the effects of gravity on the burning process in particular.

Bahadori, M. Yousef↗