Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Analytical Method Development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Separation of Lipoproteins for Quantitative Analysis of 14 C-Labeled Lipid-Soluble Compounds by Accelerator Mass Spectrometry

To date, 14 C tracer studies using accelerator mass spectrometry (AMS) have not yet resolved lipid-soluble analytes into individual lipoprotein density subclasses. The objective of this work was to develop a reliable method for lipoprotein separation and quantitative recovery for biokinetic modeling purposes. The novel method developed provides the means for use of small volumes (10–200 µL) of frozen plasma as a starting material for continuous isopycnic lipoprotein separation within a carbon- and pH-stable analyte matrix, which, following post-separation fraction clean up, created samples suitable for highly accurate 14 C/ 12 C isotope ratio determinations by AMS. Manual aspiration achieved 99.2 ± 0.41% recovery of [5- 14 CH 3 ]-(2R, 4'R, 8'R)-α-tocopherol contained within 25 µL plasma recovered in triacylglycerol rich lipoproteins (TRL = Chylomicrons + VLDL), LDL, HDL, and infranatant (INF) from each of 10 different sampling times for one male and one female subject, n = 20 total samples. Small sample volumes of previously frozen plasma and high analyte recoveries make this an attractive method for AMS studies using newer, smaller footprint AMS equipment to develop genuine tracer analyses of lipophilic nutrients or compounds in all human age ranges.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

National Hydrogen Scenarios: How Many Stations, Where, and When?

This report examines development scenarios for hydrogen station networks needed to support a national rollout of fuel cell electric vehicles (FCEVs) in the United States. It was developed within the framework of the U.S. public-private collaboration known as H2USA, with approximately 50 partners committed to enabling hydrogen infrastructure for FCEV adoption. In this report, an internally consistent analytic modeling method simulates how station networks might develop across cities and regions, assuming that successful planning and coordination activities result in a rollout of FCEVs and stations similar to California's. These scenarios are not forecasts of future market outcomes. Rather, they provide insight to various public and private stakeholders engaged in the planning and coordination required to help facilitate their own station networks, while reducing hydrogen station investment risks.

08 HYDROGEN↗

Optimal methods for preparation, separation, and determination of radium isotopes in environmental and biological samples

In recent years, radium has attracted considerable attention primarily because of the rapid increase in unconventional (fracking) drilling technology in the United States and around the world. One of the major radionuclides of interest in unconventional drilling wastes is radium isotopes ( 224 Ra, 226 Ra, 228 Ra). To access long-term risks associated with radium isotopes entering into the environment, accurate measurements of radium isotopes in environmental and biological samples are crucial. This article reviews many aspects of radium chemistry, which includes recent developments in radiochemical separations methods, advancements in analytical techniques followed by a more detailed discussion on the recent trends in radium determination.

54 ENVIRONMENTAL SCIENCES↗

Theory of collisional electron spectroscopy for gas analysis

We develop an analytical model for a proposed method of gas analysis. The method is based on collisional electron spectroscopy, where a limited number of electron scatterings on gas molecules inside the analyzer is permitted. The proposed method can be used to identify impurity species in a main gas from the resulted energy spectra of photoelectrons collected by the cathode. The photoelectrons are produced by vacuum ultraviolet-ionization of impurity species. Physical processes are explored in the case of detecting impurities in atmospheric air. The electron velocity distribution function inside the detector is derived. It is shown that the voltage dependence of the second derivative of the cathode current with respect to the applied cathode voltage can provide electron energy spectrum and subsequent identification of the impurity species.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A New Default Colormap for ParaView

ParaView is one of the most prominent software tools for scientific visualization used by scientists around the world. Color is a primary conduit to visually map data to its representation and, thus, enable investigation and interpretation of the data. Colormap selection has a significant impact on the data revealed; its design and selection is a critical aspect of scientific data visualization. A common choice for a user is the program’s default colormap, so careful consideration of this default is consequential. Although the current default colormap in ParaView, a succession of hues from cool blue to warm red, has served the community well, research shows that more nuanced colormap configurations increase discriminability while maintaining other critical metrics. These findings inspire us to revisit and update the default colors in ParaView. Here, in this study, we present a new ParaView default colormap, the criteria and methods of development, and example visualizations and analytic metrics.

97 MATHEMATICS AND COMPUTING↗

Deep Convolutional Neural Networks Exploit High-Spatial- and -Temporal-Resolution Aerial Imagery to Phenotype Key Traits in Miscanthus

Miscanthus is one of the most promising perennial crops for bioenergy production, with high yield potential and a low environmental footprint. The increasing interest in this crop requires accelerated selection and the development of new screening techniques. New analytical methods that are more accurate and less labor-intensive are needed to better characterize the effects of genetics and the environment on key traits under field conditions. We used persistent multispectral and photogrammetric UAV time-series imagery collected 10 times over the season, together with ground-truth data for thousands of Miscanthus genotypes, to determine the flowering time, culm length, and biomass yield traits. We compared the performance of convolutional neural network (CNN) architectures that used image data from single dates (2D-spatial) versus the integration of multiple dates by 3D-spatiotemporal architectures. The ability of UAV-based remote sensing to rapidly and non-destructively assess large-scale genetic variation in flowering time, height, and biomass production was improved through the use of 3D-spatiotemporal CNN architectures versus 2D-spatial CNN architectures. The performance gains of the best 3D-spatiotemporal analyses compared to the best 2D-spatial architectures manifested in up to 23% improvements in R2, 17% reductions in RMSE, and 20% reductions in MAE. The integration of photogrammetric and spectral features with 3D architectures was crucial to the improved assessment of all traits. In conclusion, our findings demonstrate that the integration of high-spatiotemporal-resolution UAV imagery with 3D-CNNs enables more accurate monitoring of the dynamics of key phenological and yield-related crop traits. This is especially valuable in highly productive, perennial grass crops such as Miscanthus, where in-field phenotyping is especially challenging and traditionally limits the rate of crop improvement through breeding.

47 OTHER INSTRUMENTATION↗

Equivalence in Dose Fall-Off for Isocentric and Nonisocentric Intracranial Treatment Modalities and Its Impact on Dose Fractionation Schemes

Purpose: To investigate whether dose fall-off characteristics would be significantly different among intracranial radiosurgery modalities and the influence of these characteristics on fractionation schemes in terms of normal tissue sparing. Methods and Materials: An analytic model was developed to measure dose fall-off characteristics near the target independent of treatment modalities. Variations in the peripheral dose fall-off characteristics were then examined and compared for intracranial tumors treated with Gamma Knife, Cyberknife, or Novalis LINAC-based system. Equivalent uniform biologic effective dose (EUBED) for the normal brain tissue was calculated. Functional dependence of the normal brain EUBED on varying numbers of fractions (1 to 30) was studied for the three modalities. Results: The derived model fitted remarkably well for all the cases (R{sup 2} > 0.99). No statistically significant differences in the dose fall-off relationships were found between the three modalities. Based on the extent of variations in the dose fall-off curves, normal brain EUBED was found to decrease with increasing number of fractions for the targets, with alpha/beta ranging from 10 to 20. This decrease was most pronounced for hypofractionated treatments with fewer than 10 fractions. Additionally, EUBED was found to increase slightly with increasing number of fractions for targets with alpha/beta ranging from 2 to 5. Conclusion: Nearly identical dose fall-off characteristics were found for the Gamma Knife, Cyberknife, and Novalis systems. Based on EUBED calculations, normal brain sparing was found to favor hypofractionated treatments for fast-growing tumors with alpha/beta ranging from 10 to 20 and single fraction treatment for abnormal tissues with low alpha/beta values such as alpha/beta = 2.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Verification methods for drift–diffusion reaction models for plasma simulations

Abstract Compared to other computational physics areas such as codes for general computational fluid dynamics, the documentation of verification methods for plasma fluid codes remains under developed. Current analytical solutions for plasma are often highly limited in terms of testing highly coupled physics, due to the harsh assumptions needed to derive even simple plasma equations. This work highlights these limitations, suggesting the method of manufactured solutions (MMSs) as a potential option for future verification efforts. To demonstrate the flexibility of MMS in verifying these highly coupled systems, the Multiphysics Object-Oriented Simulation Environment (MOOSE) framework was utilized. Thanks to the MOOSE framework’s robustness and modularity, as well as to its physics module capabilities and ecosystem applications (i.e. Zapdos and the chemical reaction network) developed for plasma physics modeling and simulation, this report lays the groundwork for a structured method of conducting plasma fluid code verification.

DeChant, Corey (ORCID:0000000293779732)↗

Predicting Student Success using Analytics in Course Learning Management Systems

Educational data analytics is an emerging discipline, concerned with developing methods for exploring the unique types of data that come from the educational context. For example, predicting college student performance is crucial for both the student and educational institutions. It can support timely intervention to prevent students from failing a course, increasing efficacy of advising functions, and improving course completion rate. In this paper, we present the efforts carried out at Oak Ridge National Laboratory (ORNL) toward conducting predictive analytics to academic data collected from 2009 through 2013 and available in one of the most commonly used learning management systems, called Moodle. First, we have identified the data features useful for predicting student outcomes such as students scores in homework assignments, quizzes, exams, in addition to their activities in discussion forums and their total GPA at the same term they enrolled in the course. Then, Logistic Regression and Neural Network predictive models are used to identify students as early as possible that are in danger of failing the course they are currently enrolled in. These models compute the likelihood of any given student failing (or passing) the current course. Numerical results are presented to evaluate and compare the performance of the developed models and their predictive accuracy.

Educational data mining↗

CCUS 2024, Interpreting the strain tensor Larry Murdoch Interpreting strain tensor data to characterize and monitor reservoirs for CO2 storage and other applications

Recent advances in instrumentation have made it feasible to measure the transient strain tensor caused by small changes in fluid volume or pressure in the subsurface and this has opened the door to new opportunities for characterization and monitoring during CCUS. We have demonstrated this method by deploying strainmeters at shallow depths (30 to 40m) and then conducting injection well tests in an underlying reservoir at 530m depth. The resulting data indicated that the horizontal strain at shallow strainmeters was tensile and the vertical strain was compressive. The radial strain was less than the horizontal strain, and the strain rates decreased from 100 nanostrain/day to roughly 10 ne/d over a few days (1 nanostrain = 1 part per billion strain). We then used the strain data to estimate reservoir properties, geometry and pressure through inversion of poroelastic forward models using both numerical and novel analytical methods. The average horizontal strain in the caprock resembles the transient pressure in the underlying reservoir and classic type-curve methods from transient well testing can be used for preliminary interpretations of strain data. We have developed fast, closed-form analytical solutions to a pressurized poroelastic inclusion and inhomogeneity in a half-space. Numerical models developed using finite element methods allow more details of the subsurface to be included in the inversion, but they require much longer run times and this makes inversion cumbersome using standard methods. We have developed an inversion approach that uses a proxy model created using machine learning to do most of the forward calculations. This approach markedly reduces the computational requirements and makes it feasible to use Bayesian inversion with large numerical models. Bayesian inversion is important because it provides predictions with uncertainties, which makes the results useful for decision making. We have shown with field tests and simulations that the strain tensor in the caprock is sensitive to pressure in the reservoir, reservoir properties and boundaries, and pressure in the caprock caused by leaks. These results indicate that measuring and interpreting the shallow strain tensor could be a valuable tool for both initial reservoir characterization efforts and long-term monitoring during CCUS. Recent advances in instrumentation have made it feasible to measure the transient strain tensor caused by small changes in fluid volume or pressure in the subsurface and our objective was to evaluate opportunities for strain monitoring during characterization and monitoring for CCUS. Our approach was to deploy strainmeters at shallow depths (30 to 40m) and then conduct injection well tests in an underlying reservoir at 530m depth. The results indicate that the horizontal strain at shallow strainmeters was tensile and the vertical strain was compressive. The radial strain was less than the horizontal strain, and the strain rates decreased from 100 nanostrain/day to roughly 10 ne/d over a few days (1 nanostrain = 1 part per billion strain). We then used the strain data to estimate reservoir properties, geometry and pressure through inversion of poroelastic forward models using both numerical and novel analytical methods. The average horizontal strain in the caprock resembles the transient pressure in the underlying reservoir and classic type-curve methods from transient well testing can be used for preliminary interpretations of strain data. We have developed fast, closed-form analytical solutions to a pressurized poroelastic inclusion and inhomogeneity in a half-space. Numerical models developed using finite element methods allow more details of the subsurface to be included in the inversion, but they require much longer run times and this makes inversion cumbersome using standard methods. We have developed an inversion approach that uses a proxy model created using machine learning to do most of the forward calculations. This approach markedly reduces the computational requirements and makes it feasible to use Bayesian inversion with large numerical models. Bayesian inversion is important because it provides predictions with uncertainties, which makes the results useful for decision making. In conclusion, we have shown with field tests and simulations that the strain tensor in the caprock is sensitive to pressure in the reservoir, reservoir properties and boundaries, and pressure in the caprock caused by leaks. These results indicate that measuring and interpreting the shallow strain tensor could be a valuable tool for both initial reservoir characterization efforts and long-term monitoring during CCUS.

Murdoch, Larry↗

Analytical continuation from bound to resonant states in the Dirac equation with quadrupole-deformed potentials

Here, resonances with pronounced single-particle characteristics are crucial for quantitative descriptions of exotic nuclei near and beyond the drip lines, and often impact halo formation and nucleon decay processes. Since the majority of nuclei are deformed, the interplay between deformation and orbital structure near threshold can lead to improved descriptions of exotic nuclei. Develop a method to study single-particle resonant orbital structure in the Dirac equation with a quadrupole-deformed Woods-Saxon potential. Determine the structure evolution of bound and resonant levels with deformation in this scheme, and examine the impact on halo formation in loosely bound systems, with a focus on the recent halo candidate nucleus 37 Mg. Analytical continuation of the coupling constant (ACCC) method is developed on the basis of the Dirac equation with a deformed Woods-Saxon potential. The scalar and vector terms in the deformed potential are determined by the energies of the valence neutron and nearby orbitals, which are extracted from a self-consistent relativistic Hartree-Bogoliubov (RHB) calculation with the PC-PK1 density functional. As a result, we compare the energies and widths of resonant orbitals in the recent halo nucleus candidate 37 Mg using the ACCC method based on the Dirac coupled-channel equations with those determined from the scattering phase shift (SPS) method. It is found that the results from the two methods agree well for narrow resonances, whereas the SPS method fails for broad resonances. Nilsson levels for bound and resonant orbitals from the ACCC method are calculated over a wide range of deformations and show some decisive hints of halo formation in 37 Mg. In conclusion, in our ACCC model for deformed potentials in the coupled-channel Dirac equations, the crossing of the configuration 1/2[321] and 5/2[312] orbitals at a deformation of approximately 0.5 enhances the probability to occupy the 1/2[321] orbital coming from 2 p3/2 thereby explaining the recent observation of a p-wave one-neutron halo configuration in 37 Mg. The resonant 1/2[301] configuration plays a crucial role in halo formation in the magnesium isotopes beyond A = 40 for a wide range of deformations larger than 0.2.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Determination of saccharides and ethanol from biomass conversion using Raman spectroscopy: Effects of pretreatment and enzyme composition

This dissertation focuses on the development of facile and rapid quantitative Raman spectroscopy measurements for the determination of conversion products in producing bioethanol from corn stover. Raman spectroscopy was chosen to determine glucose, xylose and ethanol in complex hydrolysis and fermentation matrices. Chapter 1 describes the motives and main goals of this work, and includes an introduction to biomass, commonly used pretreatment methods, hydrolysis and fermentation reactions. The principles of Raman spectroscopy, its advantages and applications related to biomass analysis are also illustrated. Chapter 2 and 3 comprise two published or submitted manuscripts, and the thesis concludes with an appendix. In Chapter 2, a Raman spectroscopic protocol is described to study the efficiency of enzymatic hydrolysis of cellulose by measuring the main product in hydrolysate, glucose. Two commonly utilized pretreatment methods were investigated in order to understand their effect on glucose measurements by Raman spectroscopy. Second, a similar method was set up to determine the concentration of ethanol in fermentation broth. Both of these measurements are challenged by the presence of complex matrices. In Chapter 3, a quantitative comparison of pretreatment protocols and the effect of enzyme composition are studied using systematic methods. A multipeak fitting algorithm was developed to analyze spectra of hydrolysate containing two analytes: glucose and xylose. Chapter 4 concludes with a future perspective of this research area. An appendix describes a convenient, rapid spectrophotometric method developed to measure cadmium in water. This method requires relatively low cost instrumentation and can be used in microgravity, such as space shuttles or the International Space Station. This work was performed under the supervision of Professor Marc Porter while at Iowa State University. Research related to producing biofuel from bio-renewable resources, especially bioethanol from biomass, has grown significantly in the past decade due to the high demand and rising costs of fossil fuels. More than 3 percent of the energy consumption in the U.S. is derived from renewable biomass, mostly through industrial heat and steam production by the pulp and paper industry, and electricity generation from municipal solid waste (MSW) and forest industry residues. The utilization of food-based biomass to make fuels has been widely criticized because it may increase food shortages throughout the world and raise the cost of food. Thus, nonfood-based and plentiful lignocellulosic feedstocks, such as corn stover, perennial grass, bagasse, sorghum, wheat/rice straw, herbaceous and woody crops, have great potential to be new bio-renewable sources for energy production. Given that many varieties of biomass are available, there is need for a rapid, simple, high-throughput method to screen the conversion of many plant varieties. The most suitable species for each geographic region must be determined, as well as the optimal stage of harvest, impacts of environmental conditions (temperature, soil, pH, etc.). Various genetically modified plants should be studied in order to establish the desired biomass in bioethanol production. The main screening challenge, however, is the complexity of plant cell wall structures that make reliable and sensitive analysis difficult. To date, one of the most popular methods to produce lignocellulosic ethanol is to perform enzymatic hydrolysis followed by fermentation of the hydrolysate with yeast. There are several vital needs related to the field of chemistry that have been suggested as primary research foci needed to effectively improve lignocellulosic ethanol production. These topics include overcoming the recalcitrance of cellulosic biomass, the pervasiveness of pretreatment, advanced biological processing and better feedstocks. In this thesis, a novel approach using Raman spectroscopy has been developed to address important issues related to bioethanol generation, which will aid the research aimed to solve the topics mentioned above.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Development of a fast and efficient analytical technique for the isotopic analysis of fission and actinide elements in environmental matrices

An automated separation–direct analysis scheme has been developed to determine both the concentration and isotopic composition of a suite of elements down to the low picogram level in a complex silicon-based matrix. With the ultimate goal of performing rapid analysis of materials with non-natural isotopic compositions, RAPID (Rapid Analysis of Post-Irradiation Debris) consists of a high-pressure ion chromatography system directly coupled to an inductively coupled plasma mass spectrometer. The RAPID method achieves matrix exclusion and direct online analysis of the elementally separated components, yielding precise isotopic compositions for up to 40 elements in less than one hour per sample. When combined with isotope dilution, this approach shows the potential to yield elemental concentrations with low uncertainties, providing a rapid analytical method that encompasses group I and II metals, transition metals, refractory metals, platinum group metals, lanthanides, and actinides. Furthermore, the method development, robustness, sensitivity, uncertainties, and potential applications in nuclear and environmental measurements will be discussed in this paper.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Automation of Extraction Chromatograhic and Ion Exchange Separations for Radiochemical Analysis and Monitoring

Radiochemical analysis, complete with the separation of radionuclides of interest from the sample matrix and from other interfering radionuclides, is often an essential step in the determination of the radiochemical composition of a nuclear sample or process stream. Although some radionuclides can be determined nondestructively by gamma spectroscopy, where the gamma rays penetrate significant distances in condensed media and the gamma ray energies are diagnostic for specific radionuclides, other radionuclides that may be of interest emit only alpha or beta particles. For these, samples must be taken for destructive analysis and radiochemical separations are required. For process monitoring purposes, the radiochemical separation and detection methods must be rapid so that the results will be timely. These results could be obtained by laboratory analysis or by radiochemical process analyzers operating on-line or at-site. In either case, there is a need for automated radiochemical analysis methods to provide speed, throughput, safety, and consistent analytical protocols. Classical methods of separation used during the development of nuclear technologies, namely manual precipitations, solvent extractions, and ion exchange, are slow and labor intensive. Fortunately, the convergence of digital instrumentation for preprogrammed fluid manipulation and the development of new separation materials for column-based isolation of radionuclides has enabled the development of automated radiochemical analysis methodology. The primary means for separating radionuclides in solution are liquid-liquid extraction and ion exchange. These processes are well known and have been reviewed in the past.1 Ion exchange is readily employed in column formats. Liquid-liquid extraction can also be implemented on column formats using solvent-impregnated resins as extraction chromatographic materials. The organic liquid extractant is immobilized in the pores of a microporous polymer material. Under suitable conditions, the analyte of interest partitions into the immobilized organic phase while other matrix speces and interferences are washed away in the mobile aqueous phase. After the wash step, retained analytes are rapidly released in one or more steps by changing the aqueous eluent, such that the analytes now partition back into the mobile phase. The development of solvent impregnated resins, their physical chemistry, technological applications for metal and radionuclide recovery, and analytical uses were described in detail in a previous chapter in this series by Cortina and Warshawsky. The extraction chromatographic approach is well suited for the isolation of radionuclides from complex sample matrixes in a rapid automated format. The development of automated radioanalytical methods is, in fact, closely coupled to the availability of such materials. In this review, we will focus on the application of radiochemical separations in automated fluidic formats for the analysis of alpha- and beta-emitting radionuclides.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Analytical Approach Treating Three-Dimensional Geometrical Effects of Parabolic Trough Collectors: Preprint

An analytical approach, as an extension of one newly developed method -- First-principle OPTical Intercept Calculation (FirstOPTIC) -- is proposed to treat the geometrical impact of three-dimensional (3-D) effects on parabolic trough optical performance. The mathematical steps of this analytical approach are presented and implemented numerically as part of the suite of FirstOPTIC code. Inaddition, the new code has been carefully validated against ray-tracing simulation results and available numerical solutions. This new analytical approach to treating 3-D effects will facilitate further understanding and analysis of the optical performance of trough collectors as a function of incidence angle.

14 SOLAR ENERGY↗

Estimation of constituent properties of concrete materials with an artificial neural network based method

Multi-scale models are developed for heterogeneous concrete materials to estimate their macroscopic mechanical properties in terms of micro-structural data. One crucial challenge of those models is the identification of local properties of constituent phases. In this paper, we present an efficient method based on Artificial Neural Networks (ANN). Typical concrete materials are taken as example. A macroscopic analytical strength criterion is established from three steps of nonlinear homogenization procedure. The macroscopic strength of materials is determined as a function of the frictional coefficient and cohesion of solid cement particles at nanometer scale, intra-particle pores, inter-particle pores and aggregates (inclusions). The objective is to identify the nanoscopic frictional coefficient and cohesion of cement particle from measured macroscopic values of uniaxial compression and tensile strengths. For this purpose, a numerical method based on the ANN is developed. With the analytical macroscopic strength criterion, sensitivity studies are first realized to identify the most important micro-structural parameters influencing the macroscopic strength of concrete. A simplified analytical macroscopic strength criterion is then proposed. A large dataset is further constructed through the inversion of the analytical strength criterion by using the aggregates volume fraction, porosity, macroscopic uniaxial tensile and compressive strengths as input variables and the frictional coefficient and cohesion of cement particles as output unknowns. An ANN model containing four hidden layers and 100 neurons in each layer is constructed and trained by using this dataset. Various types of validation of the ANN model are performed. It is found that the proposed ANN based model can effectively predict the frictional coefficient and cohesion of porous cement paste at the microscopic scale with a very good accuracy.

36 MATERIALS SCIENCE↗

Findings on Subtask 3.1 - Bakken Rich Gas Enhanced Oil Recovery Project

Total in-place oil for the Bakken petroleum system (BPS) (which includes the Bakken and Three Forks Formations) has been estimated to be 600 billion barrels (bbl). However, BPS wells have decline rates as high as 85% over the first 3 years of their lives, and primary recovery factors typically range from 3% to 10% of original oil in place. Given the low initial recovery rates, even small incremental productivity improvements could dramatically increase technically recoverable oil in the BPS. One potential solution is enhanced oil recovery (EOR) using gas injection, such as carbon dioxide (CO2) or hydrocarbon (HC) gases. While commonly used in conventional reservoirs, CO2 EOR in unconventional tight oil reservoirs has been limited to pilot tests. EOR using rich gas (mixture of methane, ethane, and propane) has also been employed in numerous pilots in several unconventional plays and has recently been successfully applied in the Eagle Ford play. If successful, large-scale gas-based EOR in the BPS could dramatically increase oil productivity and recovery factors and extend the life of the play for decades. While CO2 may be a technically suitable working fluid for EOR in the BPS, supplies are limited and costs for using CO2 in EOR pilots are prohibitively high. Meanwhile, produced gas flaring has presented challenges for BPS operators in North Dakota. Analysis conducted by the North Dakota Pipeline Authority indicates that the current gas-gathering infrastructure in North Dakota is insufficient to accommodate all of the associated gas that is produced from the BPS. The geographically isolated location of North Dakota relative to large natural gas markets, combined with suppressed natural gas prices, has made it economically challenging for industry to invest capital in expanding gas-gathering infrastructure in the state. These circumstances led to a research program conducted by the Energy & Environmental Research Center (EERC) in partnership with Liberty Resources Management Company LLC (LR) to examine the potential to use rich gas injection for EOR and mitigate flaring. A rich gas EOR pilot test was designed and executed by LR at its Stomping Horse development area in Williams County, North Dakota. From July 2018 through May 2019, a total of 160 million standard cubic feet (MMscf) of rich produced gas was injected into the BPS using five different wells in a sequential injection strategy. LR’s Leon–Gohrick drill spacing unit (DSU) was used as the test site. Regulatory oversight was provided by the North Dakota Industrial Commission (NDIC). Technical support was provided by the EERC through a series of laboratory, modeling, and field-based activities, and additional post-pilot research activities incorporated learnings from the test, developed new laboratory data, improved fracture modeling methods, and developed machine learning and big data analytics. The results from the Stomping Horse rich gas EOR pilot activities indicate that developing an effective, economical EOR approach for the BPS will require more field tests. Another key lesson learned from the Stomping Horse tests is that detailed pre- and posttest data on reservoir conditions and fluids production are essential. Robust reservoir characterization provides information that is crucial to creating realistic geomodels and conducting valid dynamic simulations of potential EOR scenarios. A detailed understanding of the completions and production history of offset wells is also necessary for valid test result interpretations. This knowledge is essential to designing the operational parameters of injectivity tests and interpreting the results. A conformance control strategy is also essential to success. Laboratory-based examinations of rich gas interactions with reservoir fluids and rocks were conducted, with an emphasis on determining the ability to mobilize oil in the tight reservoir rocks and shales of the BPS. Injection fluid composition was shown to have a positive impact on reducing reservoir oil minimum miscibility pressure (MMP), reducing interfacial tension (IFT), and altering wettability. IFT and contact angle measurements demonstrated that wettability can be altered in the presence of rich gas, suggesting the potential to improve oil recovery. Iterative modeling of surface infrastructure and reservoir performance using data generated by the various project activities was conducted. A geologic model of the Stomping Horse area was built; history-matched oil, gas, and water production was used in simulations of various EOR scenarios. Early programmatic modeling results were used to support LR’s design and operation of the EOR pilot and to provide insight regarding optimization of future commercial-scale BPS EOR design and operations. Post-pilot modeling focused on alternative methods of understanding complex fracture networks and accelerating simulation time. These led to improved simulation run times and provide excellent history-matching results. Several of these iterative models were used as the bases for developing algorithms into machine learning and big data analytics. History matching in reservoir simulation is time-consuming and computer processing-intensive. Machine learning algorithms were created, and an automated history-matching tool was developed. A large set of synthetic reservoir simulations were created to generate well responses (oil, gas, and water production, well bottomhole pressure [BHP], and tracer or propane breakthrough) for a set of EOR operating parameters that included offset well status (open or closed), injectate (rich gas or propane), injection rate, and injection well BHP. A user interface was developed to provide real-time visualization. Machine learning-based models were developed to provide rapid forecasting of well performance given a set of user-defined EOR operating parameters. These predictive models allow the user to modify the offset well status, injection rate, and injection well BHP and rapidly forecast future production performance. The combination of real-time visualization tools with real-time forecasting tools provides a framework for real-time control—operational changes that the EOR site operator can enact (e.g., changing gas injection rates) to affect the observed performance and potentially improve the EOR outcome. There is great reason to be optimistic about the future of EOR in the Bakken. The results of the laboratory studies suggest significant potential for high rates of oil mobilization using produced field gas injection under the right conditions. The results of the lab studies, combined with rigorous statistical analysis of well production data and associated modeling efforts, confirm the notion that fluid mobility within the reservoir is controlled by fractures. As more knowledge is gained about the nature and distribution of fracture networks in the Bakken, the industry will be in a better position to predict and, ultimately, influence fluid mobility. New field tests are necessary to develop a more complete understanding of those conditions. Thoughtful and creatively engineered field tests within a well-characterized geologic setting will yield the fundamental knowledge needed to take Bakken oil production to the next level. This subtask was cofunded through the EERC–U.S. Department of Energy Joint Program on Research and Development for Fossil Energy-Related Resources Cooperative Agreement No. DE-FE0024233. Nonfederal funding was provided by the North Dakota Industrial Commission’s Oil and Gas Research Program and Computer Modelling Group.

04 OIL SHALES AND TAR SANDS↗

Toward a Fieldable Atomic Mass Spectrometer for Safeguards Applications: Sample Preparation and Ionization

The International Atomic Energy Agency’s (IAEA’s) long-term research and development plan calls for the development of new methods to detect misuse at nuclear fuel cycle facilities such as reprocessing and enrichment plants. At enrichment plants, for example, the IAEA’s contemporary safeguards approaches are based on a combination of routine and random inspections that include collection of UF6 samples from in-process material and selected cylinders for subsequent analyses. These analyses include destructive analysis (DA) in a laboratory (typically by mass spectrometry [MS]) for isotopic characterization, and environmental sampling (ES) for subsequent laboratory elemental and isotopic analysis (also both typically by MS). One area of new method development includes moving this kind of isotope ratio analytical capability for DA and ES activities into the field. Some of the reasons for these developments include timeliness of results, avoidance of hazardous material shipments, and guidance for additional sample collecting. However, this capability does not already exist for several reasons, such as that most lab-based chemical and instrumental methods rely on laboratory infrastructure (highly trained staff, power, space, hazardous material handling, etc.) and require significant amounts of consumables (power, compressed gases, etc.). In addition, there are no currently available, fieldable instruments for atomic or isotope ratio analysis. To address these issues, Pacific Northwest National Laboratory (PNNL) and collaborator, Clemson University, are studying key areas that limit the fieldability of isotope ratio mass spectrometry for atomic ions: sample preparation and ionization, and reducing the physical size of a fieldable mass spectrometer. PNNL is seeking simple and robust techniques that could be effectively used by inspectors who may have no expertise in analytical MS. In this report, we present and describe the preliminary findings for three candidate techniques: matrix-assisted laser desorption/ionization (MALDI) MS, liquid sampling-atmospheric pressure glow discharge (LS-APGD), and laser ablation/ionization (LAI) MS at atmospheric pressure. Potential performance metrics for these techniques will be presented, including detectability, response, isotope ratio accuracy and precision, and ease of use.

Barinaga, Charles J.↗