Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AmP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Stability Characteristics of "Aerobic" Acetyl-CoA Synthetase of Yeast

During the purification of the "aerobic" acetyl-CoA synthetase (ACS) of Saccharomyces cerevisiae, strain LK2Gl2, it was noted that stronge at 4 C resulted in the loss of enzyme activity within 24 hr. Similar losses were observed during column chromatography. Addition of boiled extracts from either aerobic or anerobic cells completely prevents this. The stabilizing factor (SF) in these extracts is non-dialyzable and organic in nature. SF is excluded on G-25 and G-50 Sephadex columns and is slightly retarded on G-75 columns. On G-100 columns, SF elutes as a peak exactly coincident with that of cytochrome c, indicating a molecular weight of 13,000. SF activity was not destroyed by Pronase treatment, was adsorbed onto Norite, and absorbed in the UV with a single maximum at 260 nm. The action of SF could be replaced by a number of nucleotides. At 0.01 M, the order of effectiveness was: ATP>ADP>AMP>GTP>CTP>/=UTP>XTP. Even at 2 x 10(exp -4) M, ATP and ADP, but not AMP, cyclic AMP, adenosine or adenine, were effective in stabilizing this ACS. The mechanism of stabilization by ATP and AMP appears to be the same, since AMP competitively inhibited the ACS with respect to ATP in in vitro assays, while ADP gave a mixed type of inhibition, thus indicating a different mechanism. ACS from nonaerobic cells is also unstable in the absence of SF but, unlike aerobic ACS, is not affected by ATP or other nucleotides.

Satyanarayana, T.↗
NASA NTRS2003

An Analysis of the Automated Meteorological Profiling System Low Resolution Flight Element

A study was conducted to determine the quality of thermodynamic and wind data measured by or derived from the Low Resolution Flight Element (LRFE) of the Automated Meteorological Profiling System (AMPS). The AMPS LRFE replaced the Meteorological Sounding System (MSS), which was used to provide vertical profiles of thermodynamic and low-resolution wind data in support of spacecraft launch operations at the Cape Canaveral Air Force Station (CCAFS) and NASA Kennedy Space Center (KSC), Florida. Air temperature, relative humidity, and height, which are directly measured by the LRFE, are used to derive air pressure and density. Test flights were conducted where an LRFE sonde and an MSS sonde were attached to the same balloon and the two profiles were compared. MSS data was used as the standard reference data. The objective of the thermodynamic testing was to determine a) if the LRFE met Space Shuttle Program (SSP) accuracy requirements outlined in the Space Shuttle Launch and Landing Program Requirements Document (PRD) and/or, b) if the LRFE met or exceeded MSS data quality. AMPS uses the Global Positioning System (GPS) to determine wind speed and direction. In order to provide a basis for comparison, either an AMPS High Resolution Flight Element (HRFE) or a radar tracked Jimsphere was released simultaneously with each AMPS LRFE at CCAFS. The goal of these tests was to determine if the LRFE wind data met the requirement for low-resolution wind data defined in the Shuttle PRD. Based on the available data, the LRFE is shown to produce more consistent thermodynamic measurements than the MSS. The LRFE is also shown to meet the Shuttle PRD requirements for low resolution wind data.

Leahy, Frank B.↗
DOE OSTI2022

Automated Mobility Platforms: A Framework for Versatile, Energy-Efficient Urban Transportation for the 21st Century: Preprint

This paper presents automated mobility platforms (AMPs) as a framework to deliver high-quality urban mobility. AMPs leverage advances in sensing technology developed from automated roadway vehicles to provide opportunities for efficient movement of people and goods in dense urban environments, campuses, and large facilities like airports. In this paper, we layout the concept of AMPs and how they can serve the mobility needs of the population by providing service at the intersection of micromobility (services such as electric scooters or bikes), personal rapid transit, and moving walkways. Several key attributes and justification for the AMPs concept are described, including improvements to accessibility (inherent in design) covering both socioeconomic and disability equity, safety, energy efficiency, cost-effectiveness, urban land and space management, and scalability. We summarize the results from an ongoing national laboratory-sponsored, faculty-supported, student-led investigation into AMPs that includes stakeholder engagement and technical feasibility assessment.

ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2011

Structural and Functional Studies of Fatty Acyl Adenylate Ligases from E. coli and L. pneumophila

Fatty acyl-AMP ligase (FAAL) is a new member of a family of adenylate-forming enzymes that were recently discovered in Mycobacterium tuberculosis. They are similar in sequence to fatty acyl-coenzyme A (CoA) ligases (FACLs). However, while FACLs perform a two-step catalytic reaction, AMP ligation followed by CoA ligation using ATP and CoA as cofactors, FAALs produce only the acyl adenylate and are unable to perform the second step. We report X-ray crystal structures of full-length FAAL from Escherichia coli (EcFAAL) and FAAL from Legionella pneumophila (LpFAAL) bound to acyl adenylate, determined at resolution limits of 3.0 and 1.85 {angstrom}, respectively. The structures share a larger N-terminal domain and a smaller C-terminal domain, which together resemble the previously determined structures of FAAL and FACL proteins. Our two structures occur in quite different conformations. EcFAAL adopts the adenylate-forming conformation typical of FACLs, whereas LpFAAL exhibits a unique intermediate conformation. Both EcFAAL and LpFAAL have insertion motifs that distinguish them from the FACLs. Structures of EcFAAL and LpFAAL reveal detailed interactions between this insertion motif and the interdomain hinge region and with the C-terminal domain. We suggest that the insertion motifs support sufficient interdomain motions to allow substrate binding and product release during acyl adenylate formation, but they preclude CoA binding, thereby preventing CoA ligation.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2019

Structures of ATP-bound DNA ligase D in a closed domain conformation reveal a network of amino acid and metal contacts to the ATP phosphates

DNA ligases are the sine qua non of genome integrity and essential for DNA replication and repair in all organisms. DNA ligases join 3'-OH and 5'-PO 4 ends via a series of three nucleotidyl transfer steps. In step 1, ligase reacts with ATP or NAD + to form a covalent ligase-(lysyl-N$ζ$)–AMP intermediate and release pyrophosphate (PP i ) or nicotinamide mononucleotide. In step 2, AMP is transferred from ligase-adenylate to the 5'-PO 4 DNA end to form a DNA-adenylate intermediate (AppDNA). In step 3, ligase catalyzes attack by a DNA 3'-OH on the DNA-adenylate to seal the two ends via a phosphodiester bond and release AMP. Eukaryal, archaeal, and many bacterial and viral DNA ligases are ATP-dependent. The catalytic core of ATP-dependent DNA ligases consists of an N-terminal nucleotidyltransferase domain fused to a C-terminal OB domain. Here we report crystal structures at 1.4–1.8 Å resolution of Mycobacterium tuberculosis LigD, an ATP-dependent DNA ligase dedicated to nonhomologous end joining, in complexes with ATP that highlight large movements of the OB domain (~50 Å), from a closed conformation in the ATP complex to an open conformation in the covalent ligase-AMP intermediate. The LigD·ATP structures revealed a network of amino acid contacts to the ATP phosphates that stabilize the transition state and orient the PP i leaving group. A complex with ATP and magnesium suggested a two-metal mechanism of lysine adenylylation driven by a catalytic Mg 2+ that engages the ATP $α$ phosphate and a second metal that bridges the ATP $β$ and $γ$ phosphates.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2019

Encapsulin carrier proteins for enhanced expression of antimicrobial peptides

Antimicrobial peptides (AMPs) are regarded as attractive alternatives to conventional antibiotics, but their production in microbes remains challenging due to their inherent bactericidal nature. To address these limitations, we have developed a novel AMP fusion protein system based on an encapsulin nanocompartment protein and have demonstrated its utility in enhancing expression of HBCM2, an AMP with activity against Gram–negative bacteria. Here, HBCM2 was fused to the N–terminus of several Encapsulin monomer (Enc) variants engineered with multiple TEV protease recognition site insertions to facilitate proteolytic release of the fused HBCM2. Fusion of HBCM2 to the Enc variants, but not other common carrier proteins, enabled robust overexpression in Escherichia coli C43(DE3) cells. Interestingly, variants with a TEV site insertion following residue K71 in Enc exhibited the highest overexpression and HBCM2 release efficiencies compared to other variants but were deficient in cage formation. HBCM2 was purified from the highest expressing variant following TEV protease digestion and was found to be highly active in inhibiting E. coli growth (MIC = 5 μg/ml). Our study demonstrates the potential use of the Enc system to enhance expression of AMPs for biomanufacturing and therapeutic applications.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Surface Design for Immobilization of an Antimicrobial Peptide Mimic for Efficient Anti-Biofouling

Microbial surface attachment negatively impacts a wide range of devices from water purification membranes to biomedical implants. Mimics of antimicrobial peptides (AMPs) constituted from poly(N-substituted glycine) „peptoids“ are of great interest as they resist proteolysis and can inhibit a wide spectrum of microbes. We investigate how terminal modification of a peptoid AMPmimic and its surface immobilization affect antimicrobial activity. We also demonstrate a convenient surface modification strategy for enabling alkyne–azide „click“ coupling on amino-functionalized surfaces. Our results verified that the N- and C-terminal peptoid structures are not required for antimicrobial activity. Moreover, our peptoid immobilization density and choice of PEG tether resulted in a „volumetric“ spatial separation between AMPs that, compared to past studies, enabled the highest AMP surface activity relative to bacterial attachment. Our analysis suggests the importance of spatial flexibility for membrane activity and that AMP separation may be a controlling parameter for optimizing surface anti-biofouling.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Rational design of antimicrobial peptides targeting Gram-negative bacteria

Membrane-targeting host antimicrobial peptides (AMPs) can kill or inhibit the growth of Gram-negative bacteria. However, the evolution of resistance among microbes poses a substantial barrier to the long-term utility of the host AMPs. Combining experiment and molecular dynamics simulations, we demonstrate that terminal carboxyl capping enhances both membrane insertion and antibacterial activity of an AMP called P1. Furthermore, we show that a bacterial strain with evolved resistance to this peptide becomes susceptible to P1 variants with either backbone capping or lysine-to-arginine substitutions. Our results suggest that cocktails of closely related AMPs may be useful in overcoming evolved resistance.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2017

A stable partitioned FSI algorithm for rigid bodies and incompressible flow. Part I: Model problem analysis

A stable partitioned algorithm is developed for fluid-structure interaction (FSI) problems involving viscous incompressible flow and rigid bodies. This added-mass partitioned (AMP) algorithm remains stable, without sub-iterations, for light and even zero mass rigid bodies when added-mass and viscous added-damping effects are large. The scheme is based on a generalized Robin interface condition for the fluid pressure that includes terms involving the linear acceleration and angular acceleration of the rigid body. Added mass effects are handled in the Robin condition by inclusion of a boundary integral term that depends on the pressure. Added-damping effects due to the viscous shear forces on the body are treated by inclusion of added-damping tensors that are derived through a linearization of the integrals defining the force and torque. Added-damping effects may be important at low Reynolds number, or, for example, in the case of a rotating cylinder or rotating sphere when the rotational moments of inertia are small. In this second part of a two-part series, the general formulation of the AMP scheme is presented including the form of the AMP interface conditions and added-damping tensors for general geometries. A fully second-order accurate implementation of the AMP scheme is developed in two dimensions based on a fractional-step method for the incompressible Navier-Stokes equations using finite difference methods and overlapping grids to handle the moving geometry. Here, the numerical scheme is verified on a number of difficult benchmark problems.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

Effect of electrode rinse solutions on the electrodialysis of concentrated salts

The data presented indicate that modest attention to the chemistry of the electrode rinse solution can yield as much as 56% improvement in process efficiency. When operating electrodialysis (ED) with salt concentrations greater than 10,000 mg/l (as NaCl) the amperage can be relatively high even at low voltages. To maximize the overall rate of ion transport from diluate to concentrate, there is a need to minimize resistances in the electrode cells since these can represent as much as 30% of the total resistances in the entire process and in this particular ED unit, represented resistance roughly equivalent to that within the membrane stack. This work describes the performance of a 10-cell pair, 200 cm 2 (0.02 m 2 ) per membrane, pilot ED unit operated in batch mode at 5 V potential. The feedstock to the stack was varied from 0.5% to 6% NaCl. Results from Volt-amp profiles (2.0–15 V) were used as the rationale for choosing the preferred electrode rinse solution, 90 g/l (kg/m 3 ) disodium sulfate at pH 12.5. The recommended solution of 30 g/l (kg/m 3 ) disodium sulfate at neutral pH was tested against stronger solutions (60, 90, and 120 g/l (kg/m 3 ) disodium sulfate) at neutral pH and with 1 g/l (kg/m 3 ) sodium hydroxide added to yield solutions at pH 12.5. There were stark differences in the performance of the ED unit between the solutions at pH 7 and those at pH 12.5. The slopes of the Volt-amp profiles improved indicating less resistance to ion flow at pH 12.5. Most of the difference can be attributed to the greater conductivity of sodium hydroxide compared to disodium sulfate, where even a modest addition of 1 g/l (kg/m 3 ) sodium hydroxide increased the conductivity of the solution between 8 and 20% depending on the concentration of disodium sulfate. Most notably, the initiation voltage was 2.39 ± 0.08 V with solutions at pH 7 and 1.99 V ± 0.04 V when the rinse solutions were around pH 12.5, a difference of around 0.42 V. Since the full batch runs were performed at 5.0 V, this 0.42 V differential represented a loss of 8% in process efficiency. A series of tests showed a shift in initiation voltage occurred between pH 11.5 and 12.5. Nernst equations for water electrolysis are coupled with a simple flux model that estimates the concentration of hydroxide and hydronium ions at the electrode surfaces. This model indicates that the potential demanded by the electrodes is directly linked to the current. Furthermore, there is a steep drop in the potential demanded by the anode when there is sufficient hydroxide available to generate oxygen from hydroxide as opposed to generation from water. The voltage demand is minimal at pH 12.5 and reflective of the reference standard voltage (just over 1.23 V predicted at 0.1 amps). However, the flux model predicts that the voltage demanded by the electrodes at pH 7 is 1.61 V at 0.1 amps (the lowest amperage measurable with the power pack). In conclusion, comparing this result to the reference standard (E 0 = -1.23 V) yields a satisfactory explanation for the observed difference below reference standard of 0.42 V.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2016

Thermodynamic and mass transfer modeling of carbon dioxide absorption into aqueous 2-amino-2-methyl-1-propanol

Explanations for the mass transfer behavior of 2-amino-2-methyl-1-propanol (AMP) are conflicting, despite extensive study of the amine for CO 2 capture. At equilibrium, aqueous AMP reacts with CO 2 to give bicarbonate in a 1:1 ratio. While this is the same stoichiometry as a tertiary amine, the reaction rate of AMP is 100 times faster. This work aims to explain the mass transfer behavior of AMP, specifically the stoichiometry and kinetics. An eNRTL thermodynamic model was used to regress wetted-wall column mass transfer data with two activity-based reactions: formation of carbamate and formation of bicarbonate. Data spanned 40–100 C and 0.15–0.60 mol CO 2 /mol alk). The fitted carbamate rate constant is three orders of magnitude greater than the bicarbonate rate constant. Rapid carbamate formation explains the kinetics, while the stoichiometry is explained by the carbamate reverting in the bulk liquid to allow CO 2 to form bicarbonate. Understanding the role of carbamate formation and diffusion in hindered amines enables optimizing solvent amine concentration by balancing viscosity and free amine concentration. Furthermore, this improves absorber design for CO 2 capture.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2025

Antimicrobial Peptides Can Facilitate Whole Blood Safety from Bacteria: A Proof of Concept

With continuous improvements to blood donor deferrals and the availability of sensitive tests for donation screening for infectious agents, bacterial contamination of whole blood (WB) and blood components stored for transfusion is a rare event. Nonetheless, it still occurs and remains a transfusion-associated risk in terms of septic transfusion reactions (STRs) and transfusion-transmitted bacterial infections with morbidity and mortality outcomes. One of the risk mitigation strategies for bacterial contamination is to implement treatment with currently available proactive pathogen reduction technologies (PRTs) for these transfusion products. Here, as a proof of concept, we tested two recently developed unique cationic antimicrobial peptides (AMPs; D-CONGA and D-CONGA-Q7) for WB safety from bacterial contamination. In this study, WB was inoculated with Escherichia coli and Staphylococcus epidermidis and treated with the two peptides to evaluate their bactericidal efficacy. The results demonstrated that D-CONGA and D-CONGA-Q7 exhibit potent inhibitory activity against the bacteria with a minimal inhibitory concentration (MIC) range of 4–8 and 1–8 μM, respectively, depending on the bacterial species tested. Time-kill kinetics further confirmed that the peptides exhibit bactericidal efficacy at 8 μM by achieving a 5-log 10 reduction (99.999%) of the bacterial load in WB with a time-dependent killing profile. Furthermore, even at 20 μM, the AMPs did not negatively impact hemolysis or hemostatic properties. We have further demonstrated using a cationic exchange resin that the cationic AMPs can be separated and removed from WB after the peptide treatments. During 35-day WB storage at 2–8 °C, 4 μM D-CONGA-Q7 one-time treatment prevented S. epidermidis growth and preserved WB quality and integrity. Overall, the results described here provide the first proof of concept that certain AMPs, such as D-CONGA and D-CONGA-Q7, can facilitate WB safety from bacteria during storage.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2022

Limitations of Separate Cloud and Rain Categories in Parameterizing Collision-Coalescence for Bulk Microphysics Schemes

Warm rain collision-coalescence has been persistently difficult to parameterize in bulk microphysics schemes. We use a flexible bulk microphysics scheme with bin scheme process parameterizations, called AMP, to investigate reasons for the difficulty. AMP is configured in a variety of ways to mimic bulk schemes and is compared to simulations with the bin scheme upon which AMP is built. We find that an important limitation in traditional bulk schemes is the use of separate cloud and rain categories. When the drop size distribution is instead represented by a continuous distribution, the simulation of cloud-to-rain conversion is substantially improved. We also find large sensitivity to the threshold size to distinguish cloud and rain in traditional schemes; substantial improvement is found by decreasing the threshold from 40 to 25 μm. Neither the use of an assumed functional form for the size distribution nor the choice of predicted distribution moments has a large impact on the ability of AMP to simulate rain production. When predicting four total moments of the liquid drop size distribution, either with a traditional two-category, two-moment scheme with a reduced size threshold, or a four-moment single-category scheme, errors in the evolution of mass and the cloud size distribution are similar, but the single-category scheme has a substantially better representation of the rain size distribution. Optimal moment combinations for the single-category approach are investigated and appear to be linked more to the information content they provide for constraining the size distributions than to their correlation with collision-coalescence rates.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2014

Structural basis of AMPK regulation by adenine nucleotides and glycogen

AMP-activated protein kinase (AMPK) is a central cellular energy sensor and regulator of energy homeostasis, and a promising drug target for the treatment of diabetes, obesity, and cancer. Here we present low-resolution crystal structures of the human α1β2γ1 holo-AMPK complex bound to its allosteric modulators AMP and the glycogen-mimic cyclodextrin, both in the phosphorylated (4.05 Å) and non-phosphorylated (4.60 Å) state. In addition, we have solved a 2.95 Å structure of the human kinase domain (KD) bound to the adjacent autoinhibitory domain (AID) and have performed extensive biochemical and mutational studies. Altogether, these studies illustrate an underlying mechanism of allosteric AMPK modulation by AMP and glycogen, whose binding changes the equilibria between alternate AID (AMP) and carbohydrate-binding module (glycogen) interactions.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Optimizing Exogenous Surfactant as a Pulmonary Delivery Vehicle for Chicken Cathelicidin-2

The rising incidence of antibiotic-resistant lung infections has instigated a much-needed search for new therapeutic strategies. One proposed strategy is the use of exogenous surfactants to deliver antimicrobial peptides (AMPs), like CATH-2, to infected regions of the lung. CATH-2 can kill bacteria through a diverse range of antibacterial pathways and exogenous surfactant can improve pulmonary drug distribution. Unfortunately, mixing AMPs with commercially available exogenous surfactants has been shown to negatively impact their antimicrobial function. It was hypothesized that the phosphatidylglycerol component of surfactant was inhibiting AMP function and that an exogenous surfactant, with a reduced phosphatidylglycerol composition would increase peptide mediated killing at a distal site. To better understand how surfactant lipids interacted with CATH-2 and affected its function, isothermal titration calorimetry and solid-state nuclear magnetic resonance spectroscopy as well as bacterial killing curves against Pseudomonas aeruginosa were utilized. Additionally, the wet bridge transfer system was used to evaluate surfactant spreading and peptide transport. Phosphatidylglycerol was the only surfactant lipid to significantly inhibit CATH-2 function, showing a stronger electrostatic interaction with the peptide than other lipids. Although diluting the phosphatidylglycerol content in an existing surfactant, through the addition of other lipids, significantly improved peptide function and distal killing, it also reduced surfactant spreading. A synthetic phosphatidylglycerol-free surfactant however, was shown to further improve CATH-2 delivery and function at a remote site. Based on these in vitro experiments synthetic phosphatidylglycerol-free surfactants seem optimal for delivering AMPs to the lung.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Structural and mechanistic insights into the bifunctional HISN2 enzyme catalyzing the second and third steps of histidine biosynthesis in plants

The second and third steps of the histidine biosynthetic pathway (HBP) in plants are catalyzed by a bifunctional enzyme–HISN2. The enzyme consists of two distinct domains, active respectively as a phosphoribosyl-AMP cyclohydrolase (PRA-CH) and phosphoribosyl-ATP pyrophosphatase (PRA-PH). The domains are analogous to single-domain enzymes encoded by bacterial hisI and hisE genes, respectively. The calculated sequence similarity networks between HISN2 analogs from prokaryotes and eukaryotes suggest that the plant enzymes are closest relatives of those in the class of Deltaproteobacteria. In this work, we obtained crystal structures of HISN2 enzyme from Medicago truncatula (MtHISN2) and described its architecture and interactions with AMP. The AMP molecule bound to the PRA-PH domain shows positioning of the N1-phosphoribosyl relevant to catalysis. AMP bound to the PRA-CH domain mimics a part of the substrate, giving insights into the reaction mechanism. The latter interaction also arises as a possible second-tier regulatory mechanism of the HBP flux, as indicated by inhibition assays and isothermal titration calorimetry.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2011

Propagation of terahertz waves in an atmospheric pressure microplasma with Epstein electron density profile

Propagation properties of terahertz (THz) waves in a bounded atmospheric-pressure microplasma (AMP) are analyzed in this study. A modified Epstein profile model is used to simulate the electron density distribution caused by the plasma sheaths. By introducing the dielectric constant of a Drude-Lorentz model and using the method of dividing the plasma into a series of subslabs with uniform electron density, the coefficients of power reflection, transmission, and absorption are derived for a bounded microplasma structure. The effects of size of microplasma, electron density profile, and collision frequency on the propagation of THz waves are analyzed numerically. The results indicate that the propagation of THz waves in AMPs depend greatly on the above three parameters. It is demonstrated that the THz wave can play an important role in AMPs diagnostics; meanwhile, the AMP can be used as a novel potential tool to control THz wave propagation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2014

Effect of discharge current and deposition temperature on roughness and density of NbC films fabricated by ion beam sputtering technique

NbC films were prepared using Ion beam sputtering system at various discharges current from 0.4 amps to 1.2 amps at room temperature. Effect of temperature on NbC films were also studied by depositing NbC films at various temperatures from room temperature to 200,300,400 and 600°C. X-ray reflectivity (XRR) study shows that surface roughness of the film decreases with decrease in discharge current. The optimum lowest roughness 3.2Å having density 92% of bulk was achieved at discharge current 0.6 amps at 3.0 cm{sup 3}/min Ar gas flow. X-ray study also shows that film roughness decreases with increase in temperature of the film and after a certain temperature it increases with increase in temperature. The lowest surface roughness 2.1Å was achieved at 300°C with density 83% of bulk NbC at constant discharge current 0.6 amps.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗