Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Additives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Technical Evaluation of Accelerated Basin De-Inventory Material Addition to Sludge Batch 11 (Rev. 1)

The Accelerated Basin De-inventory (ABD) program involves discarding spent nuclear fuel that is currently stored in L-Basin to the Defense Waste Processing Facility (DWPF) for vitrification. The first ABD discards will occur during the preparation of Sludge Batch (SB) 11. Savannah River Mission Completion has requested that the Savannah River National Laboratory assess the technical gaps related to the increased gadolinium poisoning requirement and the impacts of performing the Low Temperature Aluminum Dissolution (LTAD) process in Tank 51 with H-Canyon discards present. The following summarizes the evaluation of the impacts of increasing the quantity of gadolinium (and related topics) from what was previously evaluated in the SRNL studies of gadolinium-poisoned ABD material solubility, the overall ABD flowsheet review, and increasing the fissile mass loading in glass: 1) Based on literature surveys, there is no indication that organic interactions with gadolinium will be significant at the high pH (typically >13) conditions of the Concentration, Storage, and Transfer Facilities. Any interactions of gadolinium with organics in DWPF are not expected to adversely impact DWPF or downstream facilities. Thus, there is little-to-no residual risk from organic interactions with gadolinium [Gap closed]; 2) Adding depleted uranium to ABD material, targeting 235 U enrichment of 4.90% within each transfer window, will mitigate potential impacts from an increase in soluble 235 U enrichment during sludge washing and LTAD. The plan to take advantage of previous transfers and allow 235 U enrichment of >5% during the final transfer window carries a risk that Tank 51 supernate will have a 235 U enrichment of >5%, which should be evaluated for acceptance; 3) Increasing the gadolinium mass ratio to 3.0:1 Gd: 235 U(eq SLU ) should lead to the same or higher partitioning of gadolinium into the solid phase within the DWPF Chemical Process Cell, resulting in both liquid and solid phases with expected partitioning of Gd consistent with the prior solubility study [Gap closed for SB11]; 4) There are no expected impacts on DWPF melt temperature and melter operations due to the minimal ~0.2 weight percent (wt%) increase in Gd concentration relative to previous sludge batches [Gap closed for SB11]; 5) As observed previously, Gd is expected to enter the off-gas system via physical entrainment, but at a slightly higher concentration than what was observed for SB9 melter off-gas pluggage deposits (0.07 wt%) [Gap closed for SB11] ; 6) There are no expected impacts on DWPF recycle or the Recycle Collection Tank glycolate destruction process. [Gap closed for SB11]; 7) Gd is projected to be a trace component in the SB11 glass (<0.5 wt%) and can be ignored for process control. Trace components do not significantly impact glass durability, thus the conclusions of the previous Product Consistency Test evaluation at a fissile mass loading of 2,500 g fissile/m3 glass still applies to SB11. The ~0.1 wt% increase in Gd2O3 concentration relative to the previous study will not impact the predictability of SB11 glass with the DWPF Product Composition Control System (PCCS) models for durability or the acceptability of glass according to the Waste Acceptance Product Specifications (WAPS) criterion for product consistency [Gap closed for SB11]; 8) No additional Toxicity Characteristic Leaching Procedure testing is necessary for SB11 and the hazardous waste specification of the SB11 DWPF waste form is unchanged after the addition of the ABD stream [Gap closed for SB11]. The following summarizes the evaluation of the impacts of adding two-thirds of the ABD material to Tank 51 prior to LTAD: 1) The addition of two-thirds of the ABD increases overall aluminum mass from 1.39×10 4 kg to 1.64×10 4 kg (15.5% ABD Al). The form of the insoluble portion of the Al resulting from ABD addition should be the more readily dissolved Al(OH) 3 and amorphous forms. The portion of the ABD aluminum that is processed by LTAD is expected to be completely soluble, thus requiring that less of the boehmite in the sludge be dissolved to reach the same Al target in the SB. [Gap closed for SB11]; The expected LTAD impact on other components, as related primarily to the components in ABD, are discussed. Gd is expected to remain insoluble during LTAD and not impact the solubility of other components. [Gap closed for SB11]; The addition of two-thirds of the ABD increases overall projected SB11 uranium mass from 4,740 kg to 13,100 kg (63% ABD U) and the projected plutonium mass from 86.0 kg to 89.5 kg (3.9% ABD Pu). The addition of all of the ABD increases overall projected SB11 uranium mass from 4,740 kg to 16,100 kg (70% ABD U) and the projected plutonium mass from 86.0 kg to 90.4 kg (5.3% ABD Pu). The 235 U enrichment will be ≤5%. The fissile uranium will be adequately poisoned by Gd and the fissile Pu will be adequately poisoned by Fe from the sludge. [Gap closed for SB11]; There is a low risk that ABD addition will impact the rheology or pumpability of the slurry. There is a low but higher risk of ABD addition prior to LTAD impacting the settling rate; Based on the evaluation of adding two-thirds of the ABD material and all of the ABD material prior to the LTAD process, there is no volume or mass limit that would need to be imposed on ABD additions prior to LTAD. [Gap closed for SB11]. Revision 1 of this report addresses a variation on the ABD additions and LTAD strategy where sodium hydroxide additions for LTAD may be performed intermittently or concurrently with an ABD addition window. The proposed change does not alter the conclusions of this evaluation.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Development of Additively Manufactured Complex Tools for Autoclave Cure Composites

IACMI Project 4.9, Tooling for Composites with Washout Features Produced by Additive Manufacturing, assembled a team including the industry lead, Ability Composites, NREL and Colorado State University (CSU). Ability Composites had originally expressed interest in alternate methods of producing tooling for composite parts. In follow-up discussions, it became clear that one of the bigger tooling challenges revolved around small production volume composite parts that were tooled on washout material due to the complex geometry. To build an understanding of the potential, both from a technology and a cost perspective, for replacing conventional washout tooling with 3D printed thermoplastic tooling, a number of commercially available dissolvable FDM printing materials were evaluated, leading to tooling representative of commercial articles of interest to Ability Composites. Ultimately, Ability Composites was able to directly compare autoclave processed prepreg composite parts produced on conventional washout tooling to composite parts molded on 3D printed dissolvable tooling produced at CSU. Small, laboratory test specimens were developed to investigate the structural performance of the candidate materials under autoclave processing conditions, which were nominally 121 °C (250 °F) and 345 kPa (50 psi). In addition, several internal structural configurations (infills) were evaluated under autoclave conditions using model materials. The results of these tests indicated that two materials, Stratasys ST 130 and Infinite Materials Solutions Aquasys 180 (AQ 180), were the best candidates, given the specified autoclave processing conditions. ST-130 was slightly more robust than AQ-180; however, the AQ-180 was carried forward as it was dissolvable in water, not requiring the basic solution needed to dissolve ST-130. Based on the preliminary material and 3D printed structures evaluations, larger tools with a truncated square pyramid geometry were created to produce prepreg composite test articles for 3D printed dissolvable tool evaluation under standard autoclave fabrication conditions. Two tools were manufactured using ST-130 and one tool using traditional ceramic washout tooling media. The tools were evaluated for geometric fidelity and surface roughness changes before and after carbon fiber/epoxy prepreg composites were manufactured on the tooling. The autoclave processing did not impact the geometry significantly and was completed at 121 °C and 345 kPa, indicating satisfactory tool performance. The results from surface roughness testing of both the resulting composite and the associated tooling indicated that an adequate surface resulted without the need for a surface sealing step, as was required for the conventional washout tooling. Based on results of the truncated pyramid tests as a basis, ST-130, AQ-120 and AQ-180 materials were carried forward to the tool geometry of interest to Ability Composites. These hollow rectangular bent ducts, which were complex in nature and not extractable after cure, were used to understand the impacts of tool material and thickness. One ST-130 tool was produced as a partially solid part, with an enclosed 40% dense infill region to reduce weight and material use. This was the same approach evaluated in the truncated pyramid portion of the study. This tool was to be envelope vacuum bagged and directly compared to a monolithic tool of conventional washout material. The traditional monolithic ceramic tool was manufactured by Ability composites using CNC-based subtractive methods. An additional five dissolvable polymer tools, manufactured from ST-130, AQ-120, and AQ-180, using a hollow design were 3D printed and used to produce carbon fiber/epoxy composite evaluation articles. These hollow dissolvable tools were expected to be less influenced by the autoclave conditions as the wall was solid and vacuum bagging was inside and outside the tool. This alternative geometry was also evaluated as an option in techno-economic modeling. Print times were reduced from in excess of 3 days to under 30 hours, while surface quality and and tool integrity were substantially improved in the transition from the partially solid tool to the hollow tooling concept. Ability Composites produced autoclave-cured prepreg ducts on each of these tools. The autoclave conditions utilized were more severe than those of the initial trials, reaching temperatures of 160 °C and a pressure of 414 kPa. Under these conditions, the partially solid 3D printed tool with skin and 40% dense infill crushed significantly; however, the thicker ST-130 hollow tool showed good promise, deforming only slightly. The thinner hollow tool walls were unsuccessful as were the other materials. Overall, the hollow tool manufacturing process saved significant amounts of time and material in manufacturing as compared to the solid ducts and produced composite surface quality improvements compared to the traditional washout tooling. The TEM was developed to allow direct comparisons between conventional washout tool manufacturing processes and those developed at CSU. It also allowed for two separate 3D printed tool geometries to be analyzed and compared. In this case, the square bent duct tool geometry was determined to be representative of common washout tools. This geometry was compared with a scaled-up version of it to assess differences in the two manufacturing processes based on tool size. The model was developed to make use of user input in the form of geometry details, process steps, manufacturing parameters, bulk material costs, capital equipment costs, and general costs to calculate overall labor, material, capital equipment, and energy costs per manufactured tool for the conventional and additive manufacturing processes for the two representative geometries. It was also able to estimate step-by-step process times for the manufacturing process and geometries. Based on significant input from Ability Composites and CSU from their knowledge gained from hands-on manufacturing of the 3D printed bent duct tool geometry, costs and process times were calculated for the two manufacturing processes. Results showed that the additive manufacturing techniques developed at CSU can substantially reduce the costs of tool manufacturing by reducing labor times and material usage. This is because additive manufacturing is a relatively hands-off process and allows for the tool design to be optimized to reduce material usage. The disadvantage, however, is that process times for additive manufacturing are significantly longer. The three-dimensional (3D) printing process is slow if tight tolerances are required, but the analysis did show that print times could be reduced with the hollow tool geometry. Also, further advances in additive manufacturing could expedite the process. Costs and process times for the tool washout process were calculated separately. They showed that costs are relatively insignificant when compared to the overall tool manufacturing processes, but with increases in tool size, costs for the conventional manufacturing approach are larger than for additive manufacturing. Again, the washout process for conventional tools is very hands-on, whereas for additively manufactured tools the print medium is dissolved in an automated detergent bath at the sacrifice of process time. The analysis showed that optimizing the additively manufactured tools may also reduce washout times. Overall, Project 4.9 demonstrated that commercially available dissolvable 3D printing materials exist that can be used to produce dissolvable tooling capable of surviving prepreg composites fabrication under autoclave conditions of 121 °C (250 °F) and 345 kPa (50 psi). An alternative hollow dissolvable tool design was developed which was structurally superior to the initial concept and was cost and time effective versus conventional washout tooling. The 3D printed sacrificial tool required no added surface sealing steps prior to composite part layup and cure, offering a significant advantage over the porous conventional washout tooling.

36 MATERIALS SCIENCE↗

Soil microbial CNP and respiration responses to organic matter and nutrient additions: Evidence from a tropical soil incubation

Soil nutrient availability has a strong influence on the fate of soil carbon (C) during microbial decomposition, contributing to Earth's C balance. While nutrient availability itself can impact microbial physiology and C partitioning between biomass and respiration during soil organic matter decomposition, the availability of labile C inputs may mediate the response of microorganisms to nutrient additions. As soil organic matter is decomposed, microorganisms retain or release C, nitrogen (N) or phosphorus (P) to maintain a stoichiometric balance. While the concept of a microbial stoichiometric homeostasis has previously been proposed, microbial biomass CNP ratios are not static, and this may have very relevant implications for microbial physiological activities. In this work, we tested the hypothesis that N, P and potassium (K) nutrient additions impact C cycling in a tropical soil due to microbial stoichiometric constraints to growth and respiration, and that the availability of energy-rich labile organic matter in the soil (i.e. leaf litter) mediates the response to nutrient addition. We incubated tropical soil from French Guiana with a 13 C labeled leaf litter addition and with mineral nutrient additions of +K, +N, +NK, +PK and +NPK for 30 days. We found that litter additions led to a ten-fold increase in microbial respiration and a doubling of microbial biomass C, along with greater microbial N and P content. We found some evidence that P additions increased soil CO 2 fluxes. Additionally, we found microbial biomass CP and NP ratios varied more widely than CN in response to nutrient and organic matter additions, with important implications for the role of microorganisms in C cycling. The addition of litter did not prime soil organic matter decomposition, except in combination with +NK fertilization, indicating possible P-mining of soil organic matter in this P-poor tropical soil. Together, these results point toward an ultimate labile organic substrate limitation of soil microorganisms in this tropical soil, but also indicate a complex interaction between C, N, P and K availability. This draws attention to the difference between microbial C cycling responses to N, P, or K additions in the tropics and explains why coupled C, N and P cycle modeling efforts cannot rely on strict microbial stoichiometric homeostasis as an underlying assumption.

13C↗

High Temperature Additive Architectures for 65% Efficiency (Final Technical Report)

This project aimed to develop advanced high-temperature additive components that contribute towards the DOE’s goal for advanced gas turbines that are capable of at least 65% efficiency in combined cycle application. The objective was to leverage state-of-the-art additive manufacturing to develop an innovative stage 1 turbine nozzle (S1N) that can provide cooling flow savings while maintaining the component durability expected in today’s gas turbines. The program had two phases. Phase I was a conceptual phase for novel advanced cooling designs enabled by additive manufacturing, as well as proposals for validation. Phase II included execution of the Phase I conceptual design, including manufacturing of prototype hardware and validation within an environment that is similar to engine operation. During Phase I of the program, the team devised a concept to reduce cooling air usage. The cooling air used in the side walls is filmed out along the side walls, while the cooling air used in the airfoil is eventually directed to near-wall channels and exits holes along the airfoil trailing end. During this program, the team performed additive trials to analyze the geometric limitations of additive manufacturing. This helped the team understand minimum wall thicknesses, hole sizes, and cooling channel dimensions among other limits. Phase II of this program pushed GE Vernova beyond its previous experience of designing and manufacturing an additively manufactured hot gas path component. Modern hot gas path components utilize material chemistries that are traditionally hard to weld, such as cast Renè 108, and exhibit solidification cracking when additively manufactured using Direct Metal Laser Melting (DMLM). Note that AM108 is a powder form of Renè 108. A S1N with advanced cooling is larger and more complex than parts previously built by additive manufacturing and required new learnings to resolve risks around solidification cracking. Finally, the team validated the design in a combustion rig that replicated operation in a gas turbine. In order to properly quantify the benefits of the new additive design, a baseline was also tested in the rig and operated under the same conditions. In addition, an uncertainty analysis was done to quantify any sources of error that could impact the results. At the end of the validation effort, it was determined that the additive nozzle exceeded the 15% reduction in cooling flow goal even with the worst-case assumptions for uncertainty.

03 NATURAL GAS↗

Systems and methods for additive manufacturing magnetic solenoids

Systems and methods for forming a magnetically-enabled part via additive manufacturing. The method includes depositing a layer of additive manufacturing material on a build plate, melting or sintering the layer of additive manufacturing material, depositing additional layers of additive manufacturing material on previous layers of additive manufacturing material, the additive manufacturing material of at least some of the additional layers being magnetically permeable, and melting or sintering the additional layers of additive manufacturing material such that the magnetically-enabled part has a transition region including at least some of the magnetically permeable additive manufacturing material.

Hatch, Jonathan Douglas↗

Systems and methods for additive manufacturing magnetic solenoids

Systems and methods for forming a magnetically-enabled part via additive manufacturing. The method includes depositing a layer of additive manufacturing material on a build plate, melting or sintering the layer of additive manufacturing material, depositing additional layers of additive manufacturing material on previous layers of additive manufacturing material, the additive manufacturing material of at least some of the additional layers being magnetically permeable, and melting or sintering the additional layers of additive manufacturing material such that the magnetically-enabled part has a transition region including at least some of the magnetically permeable additive manufacturing material.

Hatch, Jonathan Douglas↗

Functionality Selection Principle for High Voltage Lithium-ion Battery Electrolyte Additives

A new class of electrolyte additives based on cyclic fluorinated phosphate esters was rationally designed and identified as being able to stabilize the surface of a LiNi0.5Mn0.3Co0.2O2 (NMC532) cathode when cycled at potentials higher than 4.6 V vs Li+/Li. Cyclic fluorinated phosphates were designed to incorporate functionalities of various existing additives to maximize their utilization. The synthesis and characterization of these new additives are described and their electrochemical performance in a NMC532/graphite cell cycled between 4.6 and 3.0 V are investigated. With 1.0 wt % 2-(2,2,2-trifluoroethoxy)-1,3,2-dioxaphospholane 2-oxide (TFEOP) in the conventional electrolyte the NMC532/graphite cell exhibited much improved capacity retention compared to that without any additive. The additive is believed to form a passivation layer on the surface of the cathode via a sacrificial polymerization reaction as evidenced by X-ray photoelectron spectroscopy (XPS) and nuclear magnetic resonsance (NMR) analysis results. The rational pathway of a cathode-electrolyte-interface formation was proposed for this type of additive. Both experimental results and the mechanism hypothesis suggest the effectiveness of the additive stems from both the polymerizable cyclic ring and the electron-withdrawing fluorinated alkyl group in the phosphate molecular structure. The successful development of cyclic fluorinated phosphate additives demonstrated that this new functionality selection principle, by incorporating useful functionalities of various additives into one molecule, is an effective approach for the development of new additives.

fluorinated cyclic phosphate, electrolyte additive↗

Rapid Bayesian High Entropy Alloy Designs Fabricated via Wire Arc Additive Manufacturing

Purpose: This project seeks to demonstrate a new high-throughput (rapid) alloy design technique applied to creating new high entropy alloys (HEAs) for extreme environments. High entropy alloys shift the design paradigm from being focused on a single principal element (e.g. nickel-based alloys) to target alloys that include high atomic fractions (X >10%) of multiple elements. These HEA materials can exhibit sluggish diffusion and enhanced corrosion resistance, ideal for potential applications in advanced ultra supercritical (A-USC) steam cycles for power generation. Scope: The addition of multiple elements in high atomic fractions creates an enormous design space that cannot easily be investigated by traditional material design strategies such as designed of experiments (DOE). This project utilizes a Bayesian machine learning algorithm that has been modified to work with calculation of phase diagrams (CALPHAD) software. This Bayesian algorithm reduces manual inputs and increase the likelihood of achieving an optimal solution. Compositional inputs to this algorithm will be assessed using existing material property models for high temperature strength and corrosion resistance. The target for alloy performance will be a 15% (~100 ⁰C) increase in allowable service temperature beyond heat-resistant stainless steels while maintaining or improving alloy cost and corrosion resistance. Haynes 230 was selected as a baseline, which is 57 wt% Ni with 22 wt% Cr 14 wt% W, and 2 wt% Mo as solid solution strengtheners. In addition to rapid design via Bayesian machine learning, the alloys were rapidly fabricated using a multi-wire arc additive manufacturing (mWAAM) technique which allows for precise control of alloy composition and assessing of alloy design “windows” to study composition effects. Build speeds for wire-arc additive processes are among the highest for additive technologies enabling rapid and reliable sample fabrication when compared to conventional methods such as arc button melting. The mWAAM samples will be rapidly characterized via instrumented indentation for room temperature modulus and strength and for elevated temperature strength via hot hardness tests. After being screened with hardness testing, potential alloys will be further evaluated with conventional microscopy techniques including scanning electron microscopy (SEM) and transmission electron microscopy (TEM) to assess agreement with modeling results. The most promising compositions will also be evaluated by printing full sized tensile specimens for mechanical behavior tests at elevated temperatures. Results: Bayesian machine learning of a single performance function was initially used to optimize five performance metrics: 1) single phase stability, 2) yield strength, 3) creep resistance (low diffusion coefficient), 4) freezing range (weldability), and 5) material cost. The single performance function was suboptimal as assumptions had to be made about the results while formulating the optimization. A goal-oriented Bayesian optimization strategy (Hanaoka, 2021) was implemented with CALPHAD for use with the five metrics above. This multi-objective Bayesian optimization (MOBO) enabled the design of NiCrCoFe alloys with V and W additions. A base composition of NiCoCr was selected as Ni provides a stable FCC matrix, Cr aids corrosion/oxidation resistance, and Co is a solid-solutions strengthener that also improves creep by increasing the activation energy. Fe helps reduce diffusion coefficients and cost. Finally, V and W were selected for their reasonable solubility and high atomic misfit to aid in solid solution strengthening. Cracking of the mWAAM specimens was an early issue, and the Easton solidification cracking model (Easton et al., 2014a) was selected for addition to the MOBO function. High performing alloys fabricated by mWAAM included Ni 28 Cr 25 Co 26 Fe 15 V 8 and Ni 62 Cr 18 Co 1 Fe 3 W 15 . It was observed that even after adapting the mWAAM process for W, the W did not fully dissolve. To fully evaluate the Ni 62 Cr 18 Co 1 Fe 3 W 15 composition, a cored wire (80-20 NiCr sheath/powder core) was manufactured and printed via WAAM, and HIP’ing was utilized to homogenize and densify the printed alloy. The V and W alloys produced met metrics 1 (solid solution), 4 (solidification cracking), and 5 (cost). However, an unmodeled mechanism of thermal stress cracking was identified in the WAAM produced materials, perhaps exacerbated by the lack of grain boundary strengthening elements (B, C). Conclusions & Recommendations: A high-throughput (rapid) alloy design technique was applied to designing and manufacturing new high entropy alloys (HEAs) for extreme environments utilizing MOBO and mWAAM. The developed process was rapid and effective in addressing the mechanisms included in the model. The lack of grain boundary strengthening element additions (e.g., B, C) was a simplification that likely produced thermal stress cracking that turned into a large part of the investigation. Additions on the order of 0.005 wt% B and 0.05 wt% C likely would have minimized thermal stress grain boundary cracking. Overall, the high throughput design strategy is promising for rapid design of metrics-driven alloys for advanced ultra supercritical (A-USC) steam cycles for power generation. The MOBO and mWAAM process could be commercialized to accelerate metrics-driven alloy design. In addition, the cored-wire process utilized for scale-up is a promising high-volume process for WAAM alloy development and scale-up.

36 MATERIALS SCIENCE↗

Response of Stream Metabolism to Coarse Woody Debris Additions Along a Catchment Disturbance Gradient

We evaluated the ecological effectiveness of an in-stream restoration project involving coarse woody debris (CWD) additions to streams along an upland soil and vegetation disturbance gradient at the Fort Benning Military Installation near Columbus, GA. We examined short-term (immediate effectiveness) and longer-term (sustainability) responses to CWD additions by measuring ecosystem metabolism rates in 8 streams quarterly over a 6-year period, including 3 years before (2001–2003) and 3 years after (2004–2006) CWD additions that were made to half of the streams. Ecosystem respiration (ER) rates in most CWD addition streams increased relative to control streams from spring 2004 through autumn 2005, suggesting heterotrophic bacteria were the initial responders to CWD additions. Gross primary production (GPP) rates remained low (typically < 0.3 g O 2 m -2 d -1 ) but increased in some CWD addition streams relative to control streams in spring 2004 and 2005. The magnitude of ER increases in CWD addition streams during the first two years post-addition increased with catchment disturbance intensity, indicating that more heavily disturbed streams responded most strongly to restorations—an important consideration when targeting future restoration locations. Because restorations did not address actual upland disturbance, continued high erosion rates resulted in 32–77% of the added CWD being buried by year two and a corresponding return of GPP and ER rates to pre-CWD addition levels by year three. If restoration projects do not adequately address the source of catchment disturbances, CWD additions will provide only short-term increases in streambed structure and stability, hydrodynamic complexity, and nutrient and organic matter processing and retention.

54 ENVIRONMENTAL SCIENCES↗

Characterization of the Kootenai River Algae Community and Primary Productivity Before and After Experimental Nutrient Addition, 2004–2007 [Chapter 2, Kootenai River Algal Community Characterization, 2009 KTOI REPORT].

The Kootenai River ecosystem (spelled Kootenay in Canada) has experienced numerous ecological changes since the early 1900s. Some of the largest impacts to habitat, biological communities, and ecological function resulted from levee construction along the 120 km of river upstream from Kootenay Lake, completed by the 1950s, and the construction and operation of Libby Dam on the river near Libby Montana, completed in 1972. Levee construction isolated tens of thousands of hectares of historic functioning floodplain habitat from the river channel downstream in Idaho and British Columbia (B.C.) severely reducing natural biological productivity and habitat diversity crucial to large river-floodplain ecosystem function. Libby Dam greatly reduces sediment and nutrient transport to downstream river reaches, and dam operations cause large changes in the timing, duration, and magnitude of river flows. These and other changes have contributed to the ecological collapse of the post-development Kootenai River ecosystem and its native biological communities. In response to large scale loss of nutrients, experimental nutrient addition was initiated in the North Arm of Kootenay Lake in 1992, in the South Arm of Kootenay Lake in 2004, and in the Kootenai River at the Idaho-Montana border during 2005. This report characterizes baseline chlorophyll concentration and accrual (primary productivity) rates and diatom and algal community composition and ecological metrics in the Kootenai River for four years, one (2004) before, and three (2005 through 2007) after nutrient addition. The study area encompassed a 325 km river reach from the upper Kootenay River at Wardner, B.C. (river kilometer (rkm) 445) downstream through Montana and Idaho to Kootenay Lake in B.C. (rkm 120). Sampling reaches included an unimpounded reach furthest upstream and four reaches downstream from Libby Dam affected by impoundment: two in the canyon reach (one with and one without nutrient addition), a braided reach, and a meandering reach. The study design included 14 sampling sites: an upstream, unimpounded reference site (KR-14), four control (non-fertilized) canyon sites downstream from Libby Dam, but upstream from nutrient addition (KR-10 through KR-13), two treatment sites referred to collectively as the nutrient addition zone (KR-9 and KR-9.1, located at and 5 km downstream from the nutrient addition site), two braided reach sites (KR-6 and KR-7), and four meander reach sites (KR-1 through KR-4). A series of qualitative evaluations and quantitative analyses were used to assess baseline conditions and effects of experimental nutrient addition treatments on chlorophyll, primary productivity, and taxonomic composition and metric arrays for the diatom and green algae communities. Insufficient density in the samples precluded analyses of bluegreen algae taxa and metrics for pre- and post-nutrient addition periods. Chlorophyll a concentration (mg/m{sup 2}), chlorophyll accrual rate (mg/m{sup 2}/30d), total chlorophyll concentration (chlorophyll a and b) (mg/m{sup 2}), and total chlorophyll accrual rate (mg/m{sup 2}/30d) were calculated. Algal taxa were identified and grouped by taxonomic order as Cyanophyta (blue-greens), Chlorophyta (greens), Bacillariophyta (diatoms), Chrysophyta (goldens), and dominant species from each sample site were identified. Algal densities (number/ml) in periphyton samples were calculated for each sample site and sampling date. Principal Component Analysis (PCA) was performed to reduce the dimension of diatom and algae data and to determine which taxonomic groups and metrics were contributing significantly to the observed variation. PCA analyses were tabulated to indicate eigenvalues, proportion, and cumulative percent variation, as well as eigenvectors (loadings) for each of the components. Biplot graphic displays of PCA axes were also generated to characterize the pattern and structure of the underlying variation. Taxonomic data and a series of biological and ecological metrics were used with PCA for diatoms and algae. Algal metrics included a suite of abundance, diversity, richness, dominance, and other measures, whereas additional trophic status and chemical limnology metrics, Van Dam indices and morphological groupings were employed in diatom PCAs. Analysis of Variance (ANOVA) was carried out using chlorophyll metrics and taxa and metric arrays for the diatom and green algae community data for comparing site differences from 2004 through 2007. Clear, statistically significant, biological responses from chlorophyll metrics, and taxa and metrics of the diatom and algal communities were revealed following experimental nutrient addition in the Kootenai River. Chlorophyll metric responses were more often significant and generally greater in magnitude than diatom and green algae taxa and metric responses.

13 HYDRO ENERGY↗

Multiscale and Machine Learning Modeling for Process-informed Microstructure Prediction in Additively Manufactured Materials using MALAMUTE

The Advanced Materials and Manufacturing Technologies (AMMT) program under the Department of Energy Office of Nuclear Energy aims to develop and qualify additively manufactured materials for nuclear applications. One key challenge to this is the microstructural variability observed in the additively manufactured products and their impact on the properties and performance of the material in extreme environments. AMMT is using a combination of high-throughput experimental and modeling techniques to accelerate qualification. Conventionally, in-situ and ex-situ characterizations and testing are performed to correlate different aspects of the additive manufacturing process to the final product and its performance. However, adopting a trial-and-error approach to experimentally evaluate the vast range of process parameters required to capture microstructural variability is cost-prohibitive. Modeling and simulation provide a comparatively inexpensive way to understand and correlate the microstructural evolution to the processing conditions. The modeling and simulation work-packages within the AMMT program aims to use physics-based and machine learning models to develop a digital twin for additive manufacturing that can correlate the process conditions to the final product and establish a process-structure-property-performance (PSPP) correlation. The melting and subsequent solidification that occurs during the additive process is a complex phenomenon that requires multiscale multiphysics analysis. This work package focuses on understanding the role of process variabilities on the unique microstructural characteristics of additively manufactured materials. Microstructural features at the subgrain level, such as compositional micro-heterogeneity and dislocation cells, are of particular interest here since they can influence the creep properties and radiation performance. Idaho National Laboratory’s Multiphysics Object-Oriented Simulation Environment (MOOSE), specifically the MOOSE Application Library for Advanced Manufacturing UTilitiEs (MALAMUTE) software, provides an ideal platform for developing the multiphysics multiscale model to explore the intricacies of the microstructural evolution during the AM processes within a single framework. Furthermore, given that such full-fidelity simulations can be computationally intensive, reduced order models are necessary to explore the PSPP space for additively manufactured materials in an efficient, reliable, and cost-effective way. This work focuses on capturing the microstructural variabilities at the subgrain level that are often missing in the part-scale models. In fiscal year 2025, we significantly advanced upon our work in the last fiscal year, in terms of the predictive capabilities of the physics-based and ML models, by adding the capabilities to capture subgrain-level micro-segregation during solidification using phase-field model and to predict the time-dependent dynamics of the AM process through the MOGPAR model. The alloy solidification model in MOOSE incorporates the thermodynamic properties and free energy relevant to 316 stainless steel. The model demonstrates the Cr and Ni segregation that occurs during solidification, including that the rate of solidification. The microstructural evolution model is connected to the process conditions via the surrogate model developed in this work. This enables predictions of the final microstructure in conjunctions with the manufacturing process. This work supports AMMT's rapid qualification goals by laying the foundation for an efficient and cost-effective model establishing the PSPP correlation for AM. The generated microstructures and predicted micro-segregation can be used by other work packages under AMMT to evaluate the properties and environmental response of the material at the mesoscale. Thus, this work helps to identify the key microstructural features at the subgrain level that are significant in property and performance predictions of additively manufactured components. This work will also provide inputs to the large-scale process variability models to reevaluate and validate assumptions and simplifications made in the part-scale models. Furthermore, through active learning this work can help identify the data need from both modeling and experimental sides for development of a robust digital twin for additive manufacturing and accelerate the AMMT's qualification efforts.

36 - MATERIALS SCIENCE↗

Effect of additive length and chemistry on the morphology of blends of conjugated thiophenes and fullerene derivative acceptor molecules

ABSTRACT Small molecule additives have been shown to increase the device efficiency of conjugated polymer (donor) and fullerene derivative (acceptor) based organic solar cells by modifying the morphology of the device active layer. In this paper we conduct a systematic study of how additives affect the donor‐acceptor morphology using molecular dynamics simulations of blends of thiophene‐based oligomers, mimicking poly(3‐dodecylthiophene) (P3DDT) or poly(2,2′:5′,2”‐3,3”‐didocyl‐terthiophene) (PTTT), and fullerene derivatives with additives of varying length and chemical functionalization, mimicking experimentally used additives like methyl ester additives, diiodooctane, and alkanedithiols. We find that functionalization of additives with end groups that are attracted to acceptor molecules are necessary to induce increased donor‐acceptor macrophase separation. In blends where acceptors intercalate between oligomer alkyl side chains, functionalized additives decrease acceptor intercalation. Functionalized additives with shorter alkyl segments increase acceptor macrophase separation more than additives with same chemical functionalization but longer alkyl segments. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53 , 1046–1057

Marsh, Hilary S.↗

Additive to regulate the perovskite crystal film growth in planar heterojunction solar cells

We reported a planar heterojunction perovskite solar cell fabricated from MAPbI{sub 3−x}Cl{sub x} perovskite precursor solution containing 1-chloronaphthalene (CN) additive. The MAPbI{sub 3−x}Cl{sub x} perovskite films have been characterized by UV-vis, SEM, XRD, and steady-state photoluminescence (PL). UV-vis absorption spectra measurement shows that the absorbance of the film with CN additive is significantly higher than the pristine film and the absorption peak is red shift by 30 nm, indicating the perovskite film with additive possessing better crystal structures. In-situ XRD study of the perovskite films with additive demonstrated intense diffraction peaks from MAPbI{sub 3−x}Cl{sub x} perovskite crystal planes of (110), (220), and (330). SEM images of the films with additive indicated the films were more smooth and homogenous with fewer pin-holes and voids and better surface coverage than the pristine films. These results implied that the additive CN is beneficial to regulate the crystallization transformation kinetics of perovskite to form high quality crystal films. The steady-state PL measurement suggested that the films with additive contained less charge traps and defects. The planar heterojunction perovskite solar cells fabricated from perovskite precursor solution containing CN additive demonstrated 30% enhancement in performance compared to the devices with pristine films. The improvement in device efficiency is mainly attributed to the good crystal structures, more homogenous film morphology, and also fewer trap centers and defects in the films with the additive.

36 MATERIALS SCIENCE↗

Decomposition of Phosphorus-Containing Additives at a Charged NMC Surface through Potentiostatic Holds

In this work, multiple phosphorus-containing compounds were evaluated as electrolyte additives for their reactivity at the cathode surface using LiNi 0.5 Mn 0.3 Co 0.2 O 2 (NMC532) // Li 4 Ti 5 O 12 (LTO) cells with both cycling and high voltage potentiostatic holds. Additives surveyed include phosphite and phosphate derivatives with either trifluoroethyl, ethyl, or trimethylsilyl groups. With the same substituents, phosphite additives showed lower Coulombic efficiency (CE) and higher oxidation current during the potentiostatic hold. Regardless of substitution group, all phosphates showed slightly higher CE than the additive-free electrolyte (baseline), although no additive significantly decreases oxidation reactions over the course of the potentiostatic hold. Post-mortem X-ray photoelectron spectroscopy analysis of the cathodes indicates that the additive with trimethylsilyl group leads to significantly higher incidence of oxygen and phosphorus on the cathode surface for both phosphites and phosphates. Atomistic simulations indicate the susceptibility of these additives to electrochemical and chemical oxidation, showing chemical oxidation to be much more likely with the phosphite additives. Lastly, the identity of the ligands on the phosphorus-containing additive can dramatically affect both the decomposition current as well as cathode surface after the potentiostatic hold.

25 ENERGY STORAGE↗

A generic scenario analysis of end-of-life plastic management: Chemical additives

Plastic growing demand and the increment in global plastics production have raised the number of spent plastics, out of which over 90% are either landfilled or incinerated. Both methods for handling spent plastics are susceptible to releasing toxic substances, damaging air, water, soil, organisms, and public health. Improvements to the existing infrastructure for plastics management are needed to limit chemical additive release and exposure resulting from the end-of-life (EoL) stage. This article analyzes the current plastic waste management infrastructure and identifies chemical additive releases through a material flow analysis. Additionally, we performed a facility-level generic scenario analysis of the current U.S. EoL stage of plastic additives to track and estimate their potential migration, releases, and occupational exposure. Potential scenarios were analyzed through sensitivity analysis to examine the merit of increasing recycling rates, using chemical recycling, and implementing additive extraction post-recycling. Our analyses identified that the current state of plastic EoL management possesses high mass flow intensity toward incineration and landfilling. Although maximizing the plastic recycling rate is a reasonably straightforward goal for enhancing material circularity, the conventional mechanical recycling method requires improvement because major chemical additive release and contamination routes act as obstacles to achieving high-quality plastics for future reuse and should be mitigated through chemical recycling and additive extraction. In conclusion, the potential hazards and risks identified in this research create an opportunity to design a safer closed-loop plastic recycling infrastructure to handle additives strategically and support sustainable materials management efforts to transform the US plastic economy from linear to circular.

54 ENVIRONMENTAL SCIENCES↗

Re-evaluation of the impact of ternary additions of Ni and Cu on the A1 to L1{sub 0} transformation in FePt films

The impact of ternary additions of Ni (1.6-21.5 at. %) and Cu (1.3-17.3 at. %) on the A1 (face centered cubic, fcc) to L1{sub 0} phase transformation in FePt films has been re-evaluated based on compositions obtained using energy dispersive x-ray spectrometry (EDS). The data presented here serve as corrections to results reported in six previous studies [D. C. Berry and K. Barmak, J. Appl. Phys. 102, 024912 (2007); 101, 014905 (2007); 99, 08G901 (2006); D. C. Berry, J. Kim, K. Barmak, K. Wierman, E. B. Svedberg, and J. K. Howard, Scr. Mater. 53, 423 (2005); K. Barmak, J. Kim, D. C. Berry, W. N. Hanani, K. Wierman, E. B. Svedberg, and J. K. Howard, J. Appl. Phys. 97, 024902 (2005); K. Barmak, J. Kim, D. C. Berry, K. W. Wierman, E. B. Svedberg, and J. K. Howard, ibid. 95, 7486 (2004)]. The new EDS compositions do not change the following conclusions of these previous studies: (i) when ternary FeNiPt and FeCuPt alloys are compared with binary FePt alloys with the same Pt content, it is seen that additions of Ni slow the transformation kinetics, whereas additions of Cu have no measurable impact on the kinetics, (ii) the Curie temperature of the L1{sub 0} phase is lowered by additions of Ni or Cu, (iii) the Curie temperature of the A1 phase is increased by additions of Ni, but lowered by additions of Cu, and (iv) the transformation enthalpy is lowered by large additions of Ni, but is unaffected by additions of Cu. The ordering behavior of FeCuPt alloys as evidenced by the kinetic ordering temperature is compared with other reports in the literature based on magnetic measurements.

36 MATERIALS SCIENCE↗

Impact of Boron-Containing Lubricant Additive on Three-Way Catalyst Reactivity and Physicochemical Properties

Boron-containing compounds are one of the lubricant additive options due to their suitable properties for additives and have been used as commercial lubricant additives. In the present study, the impact of a boron-containing lubricant oil additive, AR9100 (BR), on Pd/Rh-based three-way catalyst (TWC) performance is investigated, and the results are compared with the baseline no-additive (NA) case and the industry standard zinc dialkyl-dithiophosphate (ZDDP) results. Accelerated engine aging is performed using a genset to expose the catalysts to lubricant additives at high temperatures. All aged TWC samples are investigated for reactivity in a bench-flow reactor and characterized using a variety of analytical techniques. Compared with the no-additive case, the temperatures of 90% conversion (T 90 ) of NO, CO, C 3 H 6 , and C 3 H 8 for the ZDDP-aged TWC sample increased by 34, 30, 37, and 48 °C. However, the T 90 of all gas species for the BR-aged TWC sample are similar to the NA-aged TWC sample. Additionally, a significant decrease in water–gas shift reactivity and oxygen storage capacity is observed in the ZDDP-aged sample, but not in the BR-aged sample. Inductively coupled plasma-optical emission spectrometry (ICP-OES) analysis and electron probe microanalysis (EPMA) maps of accelerated engine aging samples show the presence of phosphorus and boron in ZDDP- and BR-aged TWC samples, respectively. However, no boron-related peaks are observed in the X-ray diffraction (XRD) pattern of the BR-aged TWC sample, which may exist in the form of an amorphous phase.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Solvent Additives: Key Morphology-Directing Agents for Solution-Processed Organic Solar Cells

By affecting film formation during the solution processing, solvent additives can provide fine control of the active layer morphology of organic photovoltaics. As such, solvent additives form a versatile method of experimental control for enhancing organic solar cell device performance. In this review, we provide a brief history of bulk heterojunction organic photovoltaics (OPV) processed from solution and the advent of solvent additives, putting them into context with other morphology directing agents. We present our current understanding of how solvent additives impact various mechanisms of phase separation, enabled by recent advances in morphology characterization by in situ X-ray scattering, absorbance and reflectometry. Indeed, understanding solvent additives’ effects on film formation has allowed them to be applied and combined effectively and synergistically to boost OPV performance. Their success as a morphology control strategy has also prompted the use of solvent additives in related organic semiconductor technologies. Finally, we discuss the role of solvent additives in the development of next-generation OPV active layers. In conclusion, despite concerns over their environmental toxicity and role in photo-instability, solvent additives will likely remain relevant morphological directing agents as research interests evolve toward non-fullerene acceptors, ternary blends and environmentally sustainable solvents.

36 MATERIALS SCIENCE↗