Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Accident”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Thermal Design Analysis Supporting a Loss-of-Coolant-Accident Experiment at TREAT

The LOCA-SERTTA experiment vehicle along with the power and flexibility of TREAT allow for the ability to create the temperature profile evolution throughout a LOCA that would be seen in a commercial LWR. Presented in this summary are thermal-hydraulic modeling results for LOCA-SERTTA which are then compared to LOCA simulation results from a commercial LWR.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2024

Determining Reactor Operating Conditions to Prevent Xenon Walkaway Accident

The xenon walk-away is a postulated uncontrolled criticality that could occur if operators are forced to evacuate the control room in certain circumstances. This poster shows how previously held assumptions are not entirely valid and that less restrictions should be placed on operators and engineers than initially assumed.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2021

Oxidation behaviors of matrix-grade graphite during water vapor ingress accidents for high temperature gas-cooled reactors

Water ingress into cores of high temperature gas-cooled reactors (HTGRs) can cause serious safety problems in graphitic components, especially for matrix graphite, which is more vulnerable than nuclear graphite. Here in this study, oxidation behaviors of a matrix-grade graphite, ARB-B1, were investigated under simulated water ingress accidental conditions. The oxidation tests were conducted in water vapor/helium mixed atmospheres at elevated temperatures up to 1200 °C. Oxidation rates and activation energy were evaluated by mass loss measurements. The activation energy was 121.5 kJ/mol in the considered temperature range, indicating only one oxidation regime-in-pore diffusion assisted by cracks. The cracks originated from the fabrication process, acting as penetration paths for the oxidant, played an important role in the oxidation behaviors. Ungraphitized binder oxidation occurred at all temperatures, while apparent oxidation of filler particles started from 1100 °C. Moreover, oxidation effects on compressive properties and hardness of the matrix graphite were discussed in terms of oxidized microstructures. This first detailed study on matrix graphite oxidation in water vapor provides important kinetics knowledge and microstructural and mechanical data for accidental scenarios of HTGRs as well as for development of new matrix graphite materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Hydrothermal corrosion of 2nd generation FeCrAl alloys for accident tolerant fuel cladding

As part of an effort to develop advanced fuel cladding for use in light water reactors, several FeCrAl alloys have been developed at Oak Ridge National Laboratory. A second generation of these alloys bearing additional alloying elements over the previously tested model alloys were tested in boiling water reactor (BWR) conditions to determine their resistance to hydrothermal corrosion. Coupons with alloy compositions Fe–10Cr–6Al–2Mo, Fe–13Cr–5Al–2Mo, Fe–13Cr–6Al–2Mo, Fe–13Cr–7Al–2Mo, and Fe–13Cr–5Al–2Mo–1Nb were tested in normal water chemistry (NWC) and hydrogen water chemistry (HWC) for 9 months in continuously refreshing autoclaves. Commercial FeCrAl alloy APMT and Zircaloy-2 were also tested for comparison. Among samples exposed to HWC, Fe–13Cr–7Al–2Mo performed worst with an average mass loss of 1.3 mg/cm2 over 9 months. This mass loss represents an estimated thickness loss of approximately 60 μm over 6 years. Samples exposed to NWC had very small mass losses of less than 0.15 mg/cm2 or mass gains up to 0.05 mg/cm2. Based on the results of this testing, the 2nd generation FeCrAl alloys tested exhibit low wall thickness loss and are suitable in terms of corrosion resistance for use as LWR cladding in BWR-HWC and BWR-NWC under normal operating conditions.

Raiman, Stephen↗
DOE OSTI2020

Hydrothermal Corrosion of First-Generation Dual-Purpose Coatings on Silicon Carbide for Accident-Tolerant Fuel Cladding

In this study, four different commercial coatings, TiN, Cr, CrN, and Cr/CrN (multilayer) were deposited by physical vapor deposition (PVD) on high resistivity chemical vapor deposited (CVD) SiC for the dual purpose of corrosion mitigation and fission gas hermeticity. The coatings were exposed for up to 2600 hours in flowing high temperature (288-350°C), high purity, liquid water with dissolved hydrogen (0.15-3ppm) or dissolved oxygen (1-2ppm). The Cr/CrN coatings did not adhere well and spalled quickly during exposure. In oxygenated conditions, none of the coatings were protective . CrN coatings spalled preferentially at defect sites, but reacted slowly enough in the absence of defects to potentially be chemically protective. TiN coatings fully oxidized within a few hundred hours and spalled. In hydrogen, all the coatings were chemically stable. Coating failures were identified and attributed to localized spallation, potentially related to coating defects. Coating improvements are recommended to reduce spallation and improve coating protection for future generations of dual-purpose coatings.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Molecular Iodine Interactions with Metal Substrates: Towards the Understanding of Iodine Interactions in the Environment Following a Nuclear Accident

In order to evaluate the potential impacts to the public from radioiodine in a nuclear event, it is vital to expand our understanding of the interaction of molecular iodine with various surfaces. There are many potential surfaces that iodine could interact with in and around a nuclear facility, including stainless steel. This study, carried out at ambient temperature, pressure and humidity, demonstrates the highly adsorptive nature of molecular iodine on two types of austenitic stainless steel, 304L and 316L. In the authors review of available literature, Fe is the only metal in stainless steel that is assumed to react with gas-phase molecular iodine. By using a novel approach which combines Inductively Coupled Plasma-Optical Emission Spectroscopy (ICP-OES) with surface Energy Dispersive X-ray Spectroscopy (EDS) there is evidence of the formation of metal iodides that have not previously been verified or quantified. Samples exposed to gaseous molecular iodine formed an iodine containing corrosion product visible by scanning electron microcopy (SEM). Evaluation of the metals in the corrosion region using EDS was compared to a water leach of the same samples analyzed using ICP-OES. A comparison of the results provide evidence that the water leachate is representative of the corrosion layer and not the base material. Furthermore, it provides confirmation of metal iodide formation with minor stainless-steel constituents including: FeI2, NiI2, MnI2 and CrI2.

Beck, Chelsie L.↗