Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AXIAL RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Comparison of Theoretical and Experimental Unsteady Aerodynamics of Linear Oscillating Cascade With Supersonic Leading-Edge Locus

An experimental influence coefficient technique was used to obtain unsteady aerodynamic influence coefficients and, consequently, unsteady pressures for a cascade of symmetric airfoils oscillating in pitch about mid-chord. Stagger angles of 0 deg and 10 deg were investigated for a cascade with a gap-to-chord ratio of 0.417 operating at an axial Mach number of 1.9, resulting in a supersonic leading-edge locus. Reduced frequencies ranged from 0.056 to 0.2. The influence coefficients obtained determine the unsteady pressures for any interblade phase angle. The unsteady pressures were compared with those predicted by several algorithms for interblade phase angles of 0 deg and 180 deg.

Ramsey, John K.↗
NASA NTRS2000

Novel Integrated Radial and Axial Magnetic Bearing

Typically, fully active magnetically suspended systems require one axial and two radial magnetic bearings. Combining radial and axial functions into a single device allows for more compact and elegant packaging. Furthermore, in the case of high-speed devices such as energy storage flywheels, it is beneficial to minimize shaft length to keep rotor mode frequencies as high as possible. Attempts have been made to combine radial and axial functionality, but with certain drawbacks. One approach requires magnetic control flux to flow through a bias magnet reducing control effectiveness, thus resulting in increased resistive losses. This approach also requires axial force producing magnetic flux to flow in a direction into the rotor laminate that is undesirable for minimizing eddy-current losses resulting in rotational losses. Another approach applies a conical rotor shape to what otherwise would be a radial heteropolar magnetic bearing configuration. However, positional non-linear effects are introduced with this scheme and the same windings are used for bias, radial, and axial control adding complexity to the controller and electronics. For this approach, the amount of axial capability must be limited. It would be desirable for an integrated radial and axial magnetic bearing to have the following characteristics, separate inputs for radial and axial control for electronics and control simplicity, all magnetic control fluxes should only flow through their respective air gaps and should not flow through any bias magnets for minimal resistive losses, be of a homopolar design to minimize rotational losses, position related non-linear effects should be minimized, and dependent upon the design parameters, be able to achieve any radial/axial force or power ratio as desired. The integrated radial and axial magnetic bearing described in this paper exhibits all these characteristics. Magnetic circuit design, design equations, and analysis results will be presented.

Blumenstock, Kenneth A.↗
NASA NTRS2000

Novel Integration Radial and Axial Magnetic Bearing

Typically, fully active magnetically suspended systems require one axial and two radial magnetic bearings. Combining radial and axial functions into a single device allows for more compact and elegant packaging. Furthermore, in the case of high-speed devices such as energy storage flywheels, it is beneficial to minimize shaft length to keep rotor mode frequencies as high as possible. Attempts have been made to combine radial and axial functionality, but with certain drawbacks. One approach requires magnetic control flux to flow through a bias magnet reducing control effectiveness, thus resulting in increased resistive losses. This approach also requires axial force producing magnetic flux to flow in a direction into the rotor laminate that is undesirable for minimizing eddy-current losses resulting in rotational losses. Another approach applies a conical rotor shape to what otherwise would be a radial heteropolar magnetic bearing configuration. However, positional non-linear effects are introduced with this scheme and the same windings are used for bias, radial, and axial control adding complexity to the controller and electronics. For this approach, the amount of axial capability must be limited. It would be desirable for an integrated radial and axial magnetic bearing to have the following characteristics; separate inputs for radial and axial control for electronics and control simplicity, all magnetic control fluxes should only flow through their respective air gaps and should not flow through any bias magnets for minimal resistive losses, be of a homopolar design to minimize rotational losses, position related non-linear effects should be minimized, and dependent upon the design parameters, be able to achieve any radial/axial force or power ratio as desired. The integrated radial and axial magnetic bearing described in this paper exhibits all these characteristics. Magnetic circuit design, design equations, and magnetic field modeling results will be presented.

Blumenstock, Kenneth↗
NASA NTRS2018

Measurement of Noise Reduction from Acoustic Casing Treatments Installed over a Subscale High Bypass Ratio Turbofan Rotor

NASA is continuing to develop over-the-rotor acoustic liners for turbofan applications. A series of low Technology Readiness Level experiments were conducted to better understand the acoustic and aerodynamic effects of these acoustic liners. The final experiment included the evaluation of four acoustic casing treatment concepts and two baseline configurations in an internal flow axial compressor facility with a 1.5 pressure-ratio high-bypass turbofan rotor. An inlet in-duct array was utilized to extract sound power levels propagating forward from the turbofan rotor. The effect of a circumferentially grooved relative to a hardwall fan case was found to reduce the in-duct sound power level by about 1.5dB for frequencies less than 2kHz while increasing noise from 4 to 8kHz by as much as 7.5dB at low fan speeds. The four acoustic treatment concepts were incorporated into the bottoms of the circumferential grooves and found to provide an additional 1 to 2dB sound power level reduction under 2kHz. The sound power level reduction was found to be even greater, 2.5 to 3.5dB, when evaluating the reduction on rotor alone duct modes (co-rotating modes). The acoustic treatments also appeared to reduce multiple pure tone noise at transonic fan speeds. Depending on the acoustic treatment concept, the high-frequency noise created by the circumferential grooves was reduced by 1.5 to 5 dB. The total noise reduction from acoustic treatments embedded into the bottoms of circumferential grooves relative to a hardwall baseline was found to be 2.5 to 3.5dB sound power level. The sound power level reduction for rotor alone (co-rotating) modes was found to be 3.5 to 4.5dB. These results show the potential for significant turbofan noise reduction by incorporating acoustic treatments over-the-rotor.

Noise↗
NASA NTRS2018

Measurement of Noise Reduction from Acoustic Casing Treatments Installed Over a Subscale High Bypass Ratio Turbofan Rotor

NASA is continuing to develop over-the-rotor acoustic liners for turbofan applications. A series of low Technology Readiness Level experiments were conducted to better understand the acoustic and aerodynamic effects of these acoustic liners. The final experiment included the evaluation of four acoustic casing treatment concepts and two baseline configurations in an internal flow axial compressor facility with a 1.5 pressure-ratio high-bypass turbofan rotor. An inlet in-duct array was utilized to extract sound power levels propagating forward from the turbofan rotor. The effect of a circumferentially grooved relative to a hardwall fan case was found to reduce the in-duct sound power level by about 1.5dB for frequencies less than 2kHz while increasing noise from 4 to 8kHz by as much as 7.5dB at low fan speeds. The four acoustic treatment concepts were incorporated into the bottoms of the circumferential grooves and found to provide an additional 1 to 2dB sound power level reduction under 2kHz. The sound power level reduction was found to be even greater, 2.5 to 3.5dB, when evaluating the reduction on rotor alone duct modes (co-rotating modes). The acoustic treatments also appeared to reduce multiple pure tone noise at transonic fan speeds. Depending on the acoustic treatment concept, the high-frequency noise created by the circumferential grooves was reduced by 1.5 to 5 dB. The total noise reduction from acoustic treatments embedded into the bottoms of circumferential grooves relative to a hardwall baseline was found to be 2.5 to 3.5dB sound power level. The sound power level reduction for rotor alone (co-rotating) modes was found to be 3.5 to 4.5dB. These results show the potential for significant turbofan noise reduction by incorporating acoustic treatments over-the-rotor.

Aeroacoustics↗
NASA NTRS1961

Longitudinal Force and Moment Data at Mach Numbers from 0.60 to 1.40 for a Family of Elliptic Cones with Various Semiapex Angles

An investigation has been made to determine the aerodynamic characteristics of four elliptic cones having plan-form semiapex angles ranging from about 9 to 31 deg., and also for one of these cones modified on the upper surface to reduce the base area by about one half. The tests were made for angles of attack from about -2 to +21 deg., at Mach numbers from 0.60 to 1.40, and for a constant Reynolds number of 1.4 million, based on the length of the models. For each model, lift, pitching-moment, and drag coefficients, and lift-drag ratios are presented for the forebody, and axial-force coefficients are presented for the base. Calculated lift and pitching- moment curves for the elliptic cones, and lift-curve slopes for each model at supersonic Mach numbers are shown for comparison with the corresponding experimental values. Lift-drag ratios are also given for the forebody and base combined. These data are presented without discussion.

Stivers, Louis S., Jr.↗
NASA NTRS1994

CFD Assessment of Orifice Aspect Ratio and Mass Flow Ratio on Jet Mixing in Rectangular Ducts

Isothermal CFD analysis was performed on axially opposed rows of jets mixing with cross flow in a rectangular duct. Laterally, the jets' centerlines were aligned with each other on the top and bottom walls. The focus of this study was to characterize the effects of orifice aspect ratio and jet-to-mainstream mass flow ratio on jet penetration and mixing. Orifice aspect ratios (L/W) of 4-to-1, 2-to-1, and 1-to-1, along with circular holes, were parametrically analyzed. Likewise, jet-to-mainstream mass flow ratios (MR) of 2.0, 0.5, and 0.25 were systematically investigated. The jet-to-mainstream momentum-flux ratio (J) was maintained at 36 for all cases, and the orifice spacing-to-duct height (S/H) was varied until optimum mixing was attained for each configuration. The numerical results showed that orifice aspect ratio (and likewise orifice blockage) had little effect on jet penetration and mixing. Based on mixing characteristics alone, the 4-to-1 slot was comparable to the circular orifice. The 4-to-1 slot has a smaller jet wake which may be advantageous for reducing emissions. However, the axial length of a 4-to-1 slot may be prohibitively long for practical application, especially for MR of 2.0. The jet-to-mainstream mass flow ratio had a more significant effect on jet penetration and mixing. For a 4-to-1 aspect ratio orifice, the design correlating parameter for optimum mixing (C = (S/H)(sq. root J)) varied from 2.25 for a mass flow ratio of 2.0 to 1.5 for a mass flow ratio of 0.25.

Bain, D. B.↗
NASA NTRS1998

Bulk-Flow Analysis of Hybrid Thrust Bearings for Advanced Cryogenic Turbopumps

A bulk-flow analysis and computer program for prediction of the static load performance and dynamic force coefficients of angled injection, orifice-compensated hydrostatic/hydrodynamic thrust bearings have been completed. The product of the research is an efficient computational tool for the design of high-speed thrust bearings for cryogenic fluid turbopumps. The study addresses the needs of a growing technology that requires of reliable fluid film bearings to provide the maximum operating life with optimum controllable rotordynamic characteristics at the lowest cost. The motion of a cryogenic fluid on the thin film lands of a thrust bearing is governed by a set of bulk-flow mass and momentum conservation and energy transport equations. Mass flow conservation and a simple model for momentum transport within the hydrostatic bearing recesses are also accounted for. The bulk-flow model includes flow turbulence with fluid inertia advection, Coriolis and centrifugal acceleration effects on the bearing recesses and film lands. The cryogenic fluid properties are obtained from realistic thermophysical equations of state. Turbulent bulk-flow shear parameters are based on Hirs' model with Moody's friction factor equations allowing a simple simulation for machined bearing surface roughness. A perturbation analysis leads to zeroth-order nonlinear equations governing the fluid flow for the thrust bearing operating at a static equilibrium position, and first-order linear equations describing the perturbed fluid flow for small amplitude shaft motions in the axial direction. Numerical solution to the zeroth-order flow field equations renders the bearing flow rate, thrust load, drag torque and power dissipation. Solution to the first-order equations determines the axial stiffness, damping and inertia force coefficients. The computational method uses well established algorithms and generic subprograms available from prior developments. The Fortran9O computer program hydrothrust runs on a Windows 95/NT personal computer. The program, help files and examples are licensed by Texas A&M University Technology License Office. The study of the static and dynamic performance of two hydrostatic/hydrodynamic bearings demonstrates the importance of centrifugal and advection fluid inertia effects for operation at high rotational speeds. The first example considers a conceptual hydrostatic thrust bearing for an advanced liquid hydrogen turbopump operating at 170,000 rpm. The large axial stiffness and damping coefficients of the bearing should provide accurate control and axial positioning of the turbopump and also allow for unshrouded impellers, therefore increasing the overall pump efficiency. The second bearing uses a refrigerant R134a, and its application in oil-free air conditioning compressors is of great technological importance and commercial value. The computed predictions reveal that the LH2 bearing load capacity and flow rate increase with the recess pressure (i.e. increasing orifice diameters). The bearing axial stiffness has a maximum for a recess pressure rati of approx. 0.55. while the axial damping coefficient decreases as the recess pressure ratio increases. The computer results from three flow models are compared. These models are a) inertialess, b) fluid inertia at recess edges only, and c) full fluid inertia at both recess edges and film lands. The full inertia model shows the lowest flow rates, axial load capacity and stiffness coefficient but on the other hand renders the largest damping coefficients and inertia coefficients. The most important findings are related to the reduction of the outflow through the inner radius and the appearance of subambient pressures. The performance of the refrigerant hybrid thrust bearing is evaluated at two operating speeds and pressure drops. The computed results are presented in dimensionless form to evidence consistent trends in the bearing performance characteristics. As the applied axial load increases, the bearing film thickness and flow rate decrease while the recess pressure increases. The axial stiffness coefficient shows a maximum for a certain intermediate load while the damping coefficient steadily increases. The computed results evidence the paramount of centrifugal fluid inertia at low recess pressures (i.e. low loads), and where there is actually an inflow through the bearing inner diameter, accompanied by subambient pressures just downstream of the bearing recess edge. These results are solely due to centrifugal fluid inertia and advection transport effects. Recommendations include the extension of the computer program to handle flexure pivot tilting pad hybrid bearings and the ability to calculate moment coefficients for shaft angular misalignments.

SanAndres, Luis↗
NASA NTRS1993

CFD Modeling of Turbulent Duct Flows for Coolant Channel Analysis

The design of modern liquid rocket engines requires the analysis of chamber coolant channels to maximize the heat transfer while minimizing the coolant flow. Coolant channels often do not remain at a constant cross section or at uniform curvature. New designs require higher aspect ratio coolant channels than previously used. To broaden the analysis capability and to complement standard analysis tools an investigation on the accuracy of CFD predictions for coolant channel flow has been initiated. Validation of CFD capabilities for coolant channel analysis will enhance the capabilities for optimizing design parameters without resorting to extensive experimental testing. The eventual goal is to use CFD to determine the flow fields of unique coolant channel designs and therefore determine critical heat transfer coefficients. In this presentation the accuracy of a particular CFD code is evaluated for turbulent flows. The first part of the presentation is a comparison of numerical results to existing cold flow data for square curved ducts (NASA CR-3367, 'Measurements of Laminar and Turbulent Flow in a Curved Duct with Thin Inlet Boundary Layers'). The results of this comparison show good agreement with the relatively coarse experimental data. The second part of the presentation compares two cases of higher aspect ratio channels (AR=2.5,10) to show changes in axial and secondary flow strength. These cases match experimental work presently in progress and will be used for future validation. The comparison shows increased secondary flow strength of the higher aspect ratio case due to the change in radius of curvature. The presentation includes a test case with a heated wall to demonstrate the program's capability. The presentation concludes with an outline of the procedure used to validate the CFD code for future design analysis.

Ungewitter, Ronald J.↗
NASA NTRS1974

Effect of rotor-to-stator spacing on acoustic performance of a full-scale fan (QF-5) for turbofan engines

A study was made of the effect of increasing the fan rotor-to-stator spacing on the noise level of a full-scale, single-stage, 1.6-pressure-ratio fan. Noise data were obtained with axial spacing of 1.14, 1.65, and 2.27 rotor chord lengths. Over this spacing range, data indicate a reduction of 1.5 PNdb. Apparently, rotor-alone noise at the frequency at which the rotor-stator interaction noise was cut off limited the noise reduction for the QF-5 fan. It seems, however, that the reduction in sound power level with increases in spacing is potentially about 6 db over the range of spacing tested.

Balombin, J. R.↗
NASA NTRS1974

Onset of aerodynamic side forces at zero sideslip on symmetric forebodies at high angles of attack

Selected results are presented from extensive wind-tunnel tests that include variations in axial and cross-sectional shape, fineness ratio, bluntness, strakes, and boundary-layer trips over a wide range of conditions (angles of attack to 90 deg, angles of sideslip to 30 deg, Reynolds numbers from subcritical to supercritical, and Mach numbers from 0.1 to 0.7). Pointed forebodies at zero sideslip can experience side forces as large as maximum normal forces. The angle of attack at the onset of side force can be correlated with nose angle and afterbody length. Furthermore, these side forces can be reduced or eliminated by bluntness or nose strakes.

Keener, E. R.↗
NASA NTRS1979

Criteria for representing circular arc and sine wave spar webs by non-curved elements

The basic problem of how to simply represent a curved web of a spar in a finite element structural model was addressed. The ratio of flat web to curved web axial deformations and longitudinal rotations were calculated using NASTRAN models. Multiplying factors were developed from these calculations for various web thicknesses. These multiplying factors can be applied directly to the area and moment of inertia inputs of the finite element model. This allows the thermal stress relieving configurations of sine wave and circular arc webs to be simply accounted for in finite element structural models.

Jenkins, J. M.↗
NASA NTRS1980

Laser-Doppler velocimetry measurements in a motored IC engine simulator

A measurement technique and experimental results are presented for mean velocity and velocity fluctuations in a motored, axisymmetric engine chamber simulation. Three valve configurations are considered: open orifice, open valve, and operating valve. Measurements of axial and tangential velocity components have been taken at various axial and radial positions for one compression ratio (7:1) and one rpm level (31). The measurements show that the intake stroke (in both two and four stroke operations) result in a recirculating flow with substantial turbulence generation even at the low rpm value. The four-stroke results in an axisymmetric design are novel and especially significant since the ability exists to make comparisons with theoretical, axisymmetric, turbulent results.

Gany, A.↗
NASA NTRS1980

Aerodynamic aspects of shock containing jet plumes

Aerodynamic and acoustic measurements of shock-free and shock-containing plumes were acquired for several supersonic free-jet model nozzles. The purpose was to investigate important features of the broadband shock noise generation process. The aerodynamic measurements include the variation of shock cell spacing and strength as a function of nozzle pressure ratio, and longitudinal turbulent-mass-flux axial development as determined by a hot-film probe. In addition, correlations of the hot-film probe with a near-field microphone were obtained. These measurements provide useful information concerning the relation of peak shock noise frequency and level with variations in shock cell spacing and strength. In general, it is shown that a distinction must be made between plumes containing weak and strong imbedded shocks. Strong shocks diminish the level of emitted shock noise and influence the behavior of the jet mixing noise process. The probable location and spectral content for the shock-shear layer interaction mechanism is indicated by the correlations. Numerical inviscid plume comparisons with experimental data are also included.

Seiner, J. M.↗
NASA NTRS1983

The performance of an annular vane swirler

In connection with the desirability of optimizing the design of a gas turbine combustion chamber, there exists a need for a more complete understanding of the fluid dynamics of the flow in such chambers. In order to satisfy this need, experimental and theoretical research is being conducted with the objective to study two-dimensional axisymmetric geometries under low speed, nonreacting, turbulent, swirling flow conditions. The flow enters the test section and proceeds into a larger chamber. Inlet swirl vanes are adjustable to a variety of vane angles. The present investigation concentrates on the time-mean flow characteristics which are generated by the upstream annular swirler. The investigation makes use of a five-hole pitot probe technique. A theoretical analysis of swirl numbers associated with several idealized exit velocity profiles is included, and values of the ratio of maximum swirl velocity to maximum axial velocity at different swirl strengths are given for each case.

Lilley, D. G.↗
NASA NTRS1987

Effects of forebody geometry on subsonic laminar boundary layer stability

The effect of forebody geometry on the stability of the laminar boundary layer on axisymmetric body shapes at Reynolds numbers typical of small and medium sized aircraft in low-subsonic cruise flight is investigated. It is found that small nose radii are important in obtaining n-factors of 9 on axisymmetric bodies of fineness ratio of about 6 at large nondimensional axial distances downstream. Results for the effect of the steepness of the pressure gradient and the value of the minimum pressure on the extent of laminar flows on an axisymmetric body at a given Reynolds number are also presented.

Dodbele, S. S.↗