Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AXIAL COMPRESSION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Neutron yield enhancement and suppression by magnetization in laser-driven cylindrical implosions

In inertial confinement fusion, an externally applied magnetic field can reduce heat losses in the compressing fuel thereby increasing neutron-averaged ion temperatures and neutron yields. Yet, magnetization is only beneficial if the magnetic pressure remains negligible compared to the fuel pressure. Experiments and three-dimensional magneto-hydrodynamic simulations of cylindrical implosions on the OMEGA laser show ion temperature and neutron yield enhancements of up to 44% and 67%, respectively. As the applied, axial magnetic field is increased to nearly 30T, both experiments and simulations show yield degradation. For magnetized, cylindrical implosions, there exists an optimal magnetic field that maximizes the increase in yield. Limiting the fuel convergence ratio by preheating the fuel can further increase the benefit of magnetization. The findings demonstrate that it is possible to create a plasma with a density of order 1 g/cm 3 and an ion temperature greater than 1 keV with a magnetic pressure comparable to the thermal pressure, a new regime for laser-produced plasmas on OMEGA.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2017

Novel penta-graphene nanotubes: strain-induced structural and semiconductor–metal transitions

Research into novel one-dimensional (1D) materials and associated structural transitions is of significant scientific interest. It is widely accepted that a 1D system with a short-range interaction cannot have 1D phase transition at finite temperature. In this paper, we propose a series of new stable carbon nanotubes by rolling up penta-graphene sheets, which exhibit fascinating well-defined 1D phase transitions triggered by axial strain. Our first-principles calculations show that such penta-graphene nanotubes (PGNTs) are dynamically stable by phonon calculations, but transform from a tri-layer structure to a highly defective single-walled nanotube at low temperature in molecular dynamics simulations. We show that moderate compressive strains can drive structural transitions of (4,4), (5,5), and (6,6) PGNTs, during which the distances of neighboring carbon dimers in the inner shell have a sudden drop, corresponding to dimer–dimer nonbonding to bonding transitions. After such transition, the tubes become much more thermally stable and undergo semiconductor–metal transitions under increasing strain. The band gaps of PGNTs are not sensitive to chirality whereas they can be tuned effectively from visible to short-wavelength infrared by appropriate strain, making them appealing materials for flexible nano-optoelectronics. In conclusion, these findings provide useful insight into unusual phase transitions in low-dimensional systems.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Analysis of magnetically immersed electron guns with non-adiabatic fields

Electron diode guns, which have strongly varying magnetic or electric fields in a cathode-anode gap, were investigated in order to generate laminar electron beams with high current density using magnetically immersed guns. By creating a strongly varying radial electric field in a cathode-anode gap of the electron gun, it was demonstrated that the optical properties of the gun can be significantly altered, which allows the generation of a laminar, high-current electron beam with relatively low magnetic field on the cathode. The relatively high magnetic compression of the electron beam achieved by this method is important for producing electron beams with high current density. A similar result can be obtained by inducing a strong variation of the magnetic field in a cathode-anode gap. It was observed that creating a dip in the axial magnetic field in the cathode-anode gap of an adiabatic electron gun has an optical effect similar to guns with strong variation of radial electric field. By analyzing the electron trajectories angles and presenting the results in a gun performance map different geometries of magnetically immersed electron guns with non-adiabatic fields are compared with each other and with a more traditional adiabatic electron gun. Some advantages and limitations of guns with non-adiabatic fields are outlined. In conclusion, the tests results of non-adiabatic electron gun with modified magnetic field are presented.

43 PARTICLE ACCELERATORS↗
DOE OSTI2020

Two-temperature effects in Hall-MHD simulations of the HIT-SI experiment

A two-temperature Hall-magnetohydrodynamic (Hall-MHD) model, which evolves the electron and ion temperatures separately, is implemented in the PSI-Tet 3D MHD code and used to model plasma dynamics in the Helicity Injected Torus–Steady Inductive (HIT-SI) experiment. The two-temperature model is utilized for HIT-SI simulations in both the PSI-Tet and NIMROD codes at a number of different injector frequencies in the 14.5–68.5 kHz range. At all frequencies, the NIMROD two-temperature model results in increased toroidal current, lower chord-averaged density, higher average temperatures, outward radial shift of the current centroid, and axial symmetrization of the current centroid, relative to the single-temperature NIMROD simulations. The two-temperature PSI-Tet model illustrates similar trends, but at high frequency operation, it exhibits lower electron temperature, smaller toroidal current, and decreased axial symmetrization with respect to the single-temperature PSI-Tet model. With all models, average temperatures and toroidal currents increase with the injector frequency. Power balance and heat fluxes to the wall are calculated for the two-temperature PSI-Tet model and illustrate considerable viscous and compressive heating, particularly at high injector frequency. Parameter scans are also presented for artificial diffusivity, wall temperature, and density. Both artificial diffusivity and the density boundary condition significantly modify the plasma density profiles, leading to larger average temperatures, toroidal current, and relative density fluctuations at low densities. As a result, a low density simulation achieves sufficiently high current gain (G > 5) to generate significant volumes of closed flux lasting 1–2 injector periods.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Processing Compressed Expanded Natural Graphite for Phase Change Material Composites

Phase change materials (PCMs) are used in various thermal energy storage applications but are limited by their low thermal conductivity. One method to increase conductivity involves impregnating organic PCMs into highly porous conductive matrix materials. Of these materials, compressed expanded natural graphite (CENG) matrices have received the most attention. Despite this attention, the effect that CENG processing has on PCM saturation and overall matrix thermal conductivity has not been fully investigated. Therefore, the effect of the heat treatment process used to expand intercalated graphite flakes is evaluated here. Higher heat treatment temperatures yielded higher saturation rates and overall saturation at similar matrix porosities. For example, increasing temperature from 300 °C to 700 °C resulted in approximately 60%-70% increase in pore saturation after 100 minutes of soaking. The exposure time to heat treatment had less of an effect on PCM saturation. The exposure time had negligible effect above 30 min and above 500 °C heating temperatures. However, because the expanded graphite was found to oxidize around 700 °C, the use of longer exposure time in manufacturing applications can be beneficial if a shortened impregnation time is needed. Heat treatment conditions did not impact thermal conductivity. The composite latent heat of fusion was also reduced approximately proportionally to the PCM mass fraction. A local maximum in axial thermal conductivity was observed at around 83% porosity, which is similar to previous studies. The observed conductivity at this maximum was a factor of 81 times greater than the conductivity of the PCM.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Integrated simulations of premagnetized and self-magnetizing dynamic screw pinch-driven MagLIF

Magnetically driven implosions such as in magnetized liner inertial fusion (MagLIF) on the Z accelerator suffer from magneto-Rayleigh–Taylor instabilities (MRTI) that dynamically redistribute liner mass during implosion, limiting fusion fuel compression and confinement, which ultimately degrades performance. Driving the implosion with an initially helical drive field that dynamically shifts the direction of the magnetic field surrounding the liner (i.e., a dynamic screw pinch, DSP) is a method proposed to mitigate MRTI in-flight and improve target performance. In DSPs, the axial drive magnetic field component implodes the liner and diffuses through the shocked, melted liner material into the fuel throughout the implosion. Liners can be designed to enable enough axial magnetic flux to diffuse through the liner material to effectively magnetize the fuel region without the need of an initial axial magnetic field (i.e., from external field coils). We present results from three-dimensional radiation-magnetohydrodynamic simulations of MagLIF implosions employing drive magnetic fields composed of axial and azimuthal components (a helical drive field). These simulated DSP-driven MagLIF targets demonstrate improved fuel conditions and thermonuclear yield compared to a traditional MagLIF target implosion. Synthetic x-ray radiography of the imploding liner material and x-ray emission images of the fuel region at the time of peak neutron yield rate indicate superior implosion morphology for DSP-MagLIF implosions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2011

Effect of process variables on the quality attributes of briquettes from wheat, oat, canola and barley

Effect of process variables on the quality attributes of briquettes from wheat, oat, canola and barley straw Jaya Shankar Tumuluru*, L. G. Tabil, Y. Song, K. L. Iroba and V. Meda Biomass is a renewable energy source and environmentally friendly substitute for fossil fuels such as coal and petroleum products. Major limitation of biomass for successful energy application is its low bulk density, which makes it very difficult and costly to transport and handle. To overcome this limitation, biomass has to be densified. The commonly used technologies for densification of biomass are pelletization and briquetting. Briquetting offers many advantages at it can densify larger particles sizes of biomass at higher moisture contents. Briquetting is influenced by a number of feedstock and process variables such as moisture content, particle size distribution, and some operating variables such as temperature and densification pressure. In the present study, experiments were designed and conducted based on Box-Behnken design to produce briquettes using barley, wheat, canola and barley straws. A laboratory scale hydraulic briquette press was used for the present study. The experimental process variables and their levels used in the present study were pressure levels (7.5, 10, 12.5 MPa), three levels of temperature (90, 110, 130 C), at three moisture content levels (9, 12, 15% w.b.), and three levels of particle size (19.1, 25.04, 31.75 mm). The quality variables studied includes moisture content, initial density and final briquette density after two weeks of storage, size distribution index and durability. The raw biomass was initially chopped and size reduced using a hammer mill. The ground biomass was conditioned at different moisture contents and was further densified using laboratory hydraulic press. For each treatment combination, ten briquettes were manufactured at a residence time of about 30 s after compression pressure setpoint was achieved. After compression, the initial dimensions and the final dimensions after 2 weeks of storage in controlled environment of all the samples were measured. Durability, dimensional stability, and moisture content tests were conducted after two weeks of storage of the briquettes produced. Initial results indicated that moisture content played a significant role on briquettes durability, stability, and density. Low moisture content of the straws (7-12%) gave more durable briquettes. Briquette density increased with increasing pressure depending on the moisture content value. The axial expansion was more significant than the lateral expansion, which in some cases tended to be nil depending on the material and operating variables. Further data analysis is in progress in order to understand the significance of the process variables based on ANOVA. Regression models were developed to predict the changes in quality of briquettes with respect of the process variables under study. Keywords: Herbaceous biomass, densification, briquettes, density, durability, dimensional stability, ANOVA and regression equations

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2017

Nonlinear Feature Extraction and Energy Dissipation of Foam/Metal Interfaces

The physical mechanisms of energy dissipation in foam to metal interfaces must be understood in order to develop predictive models of systems with foam packaging common to many aerospace and aeronautical applications. Experimental data was obtained from hardware termed Ministack, which has large, unbonded interfaces held under compressive preload. This setup has a solid aluminum mass placed into two foam cups which are then inserted into an aluminum can and fastened with a known preload. Ministack was tested on a shaker using upward sine sweep base acceleration excitations to estimate the linearized natural frequency and energy dissipation of the first axial mode. The experimental system was disassembled and reassembled before each series of tests in order to observe the effects of the assembly to assembly variability on the dynamics. Additionally, Ministack was subjected to upward and downward sweeps to gain some understanding of the nonlinearities. Finally, Ministack was tested using a transient input, and the ring down was analyzed to find the effective stiffness and damping. There are some important findings in the measured data: there is significant assembly to assembly variability, the order in which the sine sweeps are performed influence s the dynamic response, and the system exhibits nontrivial damping and stiffness nonlinearities that must be accounted for in modeling efforts .

42 ENGINEERING↗
DOE OSTI2016

Investigation of the dynamic stress–strain response of compressible polymeric foam using a non-parametric analysis

Dynamic stress–strain response of rigid closed-cell polymeric foams is investigated in this work by subjecting high toughness polyurethane foam specimens to direct impact with different projectile velocities and quantifying their deformation response with high speed stereo-photography together with 3D digital image correlation. The measured transient displacement field developed in the specimens during high stain rate loading is used to calculate the transient axial acceleration field throughout the specimen. A simple mathematical formulation based on conservation of mass is also proposed to determine the local change of density in the specimen during deformation. By obtaining the full-field acceleration and density distributions, the inertia stresses at each point in the specimen are determined through a non-parametric analysis and superimposed on the stress magnitudes measured at specimen ends to obtain the full-field stress distribution. Furthermore, the process outlined above overcomes a major challenge in high strain rate experiments with low impedance polymeric foam specimens, i.e. the delayed equilibrium conditions can be quantified.

42 ENGINEERING↗
DOE OSTI2022

Research on Deformation Law of Deep Foundation Pit of Station in Core Region of Saturated Soft Loess Based on Monitoring

Saturated soft loess has a large pore structure, high compressibility, low strength, fluid plastic state, and poor engineering properties. It is still one of the key problems that engineering needs to solve. In order to study the influence of deep foundation pit excavation in the saturated soft loess area on the deformation of foundation pits, the deformation laws of ground settlement, enclosure structure, and supporting axial force were clarified based on the field tests on the deformation characteristics of deep foundation pits in areas with the high-water level in saturated soft loess, combined with geological conditions and on-site construction procedures. The results indicate the following: water supply and construction process were found to be the main factor in changing the surface settlement curve of deep foundation pits in saturated soft loess; increasing the construction speed of the pit bottom floor, inverted braces, floor frame beams, and sidewall frame beams to close the structure, which is conducive to restraining the deformation of the continuous underground wall and foundation pits in similar areas. In the initial stage of support layout, the axial force of steel support tends to increase too fast or even exceed the standard control value. Therefore, a reasonable preadding axial force is an effective means to control the deformation of the continuous underground wall and the axial force of the steel support. The current research results may provide a reference for constructing deep foundation pits in similar areas.

Wang, Xueyan↗
DOE OSTI2019

Permanent densification of silica glass for pressure calibration between 9 and 20 GPa at ambient temperature

Permanent density increase of silica glass was used to calibrate pressure generation delivered by cupped sintered diamond anvils (‘dimple anvils’) [Haberl B, Molaison JJ, Neuefeind JC, et al. Simple modified Bridgman anvil design for high pressure synthesis and neutron scattering. High Press. Res. submitted] within the Paris-Edinburgh press between approximately 9 and 20 GPa. Raman spectral changes of recovered silica glass with increased density were used to determine the maximum pressure reached by following an established calibration curve [Deschamps T, Kassir-Bodon A, Sonneville C, et al. Permanent densification of compressed silica glass: a Raman-density calibration curve. J. Phys. Condens. Matter. 2013;25:025402]. The monotonic Raman shift of the Main Band spectral region (~200–700 cm-1) of silica glass recovered from 9 to 20 GPa allows for continuous pressure calibration and is applicable to all presses that operate within this pressure range. Radial & axial Raman profiles were conducted to determine the pressure distribution within the sample chamber. This technique has been verified by in situ resistance measurements of the insulator-to-metal phase transition of ZnS near 15 GPa.

catalysis (heterogeneous)↗
DOE OSTI2012

Fuel Performance Modeling Results for Representative FCRD Irradiation Experiments: Projected Deformation in the Annular AFC-3A U-10Zr Fuel Pins and Comparison to Alternative Designs

The objective of the present study was to predict the outcome of the AFC-3A annular U-10Zr fuel irradiation experiment. Specifically, the study attempted to predict whether the annular fuel will swell inward and fill the annulus, or swell outward resulting in an undesirable cladding deformation. It was predicted that both 55% and 75% annular fuels operating at 350 W/cm for 201 days will swell inward and partially fill the annulus which signifies a positive outcome of the experiment. The driving mechanism for such behavior is the fuel creep under the compressive stress exerted on the fuel by the cladding as a result of the fuel cladding mechanical interaction. Comparison with the solid fuel revealed that the annular fuel is expected to swell less early in life due to the mechanical constraint provided by the cladding. Furthermore, mechanical constraint is expected to yield a marked reduction of the axial elongation of the annular fuel as compared to the solid fuel. The prediction is based on the assumption that the annular fuel is not capable of moving axially relative to the cladding after the two come in contact. Post irradiation examination results would be very useful to assess the validity of this assumption. Specifically, underprediction of the axial growth would point to the fact that some slippage of the fuel relative to the cladding occurs after the onset of the FCMI. As fuel creep plays the major role in the deformation of the annular fuel, the contributions from the thermal and irradiation induced creep to the total creep rate of fuel were examined to provide guidance for possible creep testing experiments of the fuel (separate effect tests). It was found that irradiation induced creep dominates deformation of the fresh fuel at low temperatures. At high temperatures, and in the case of porous fuel, the thermal creep of the fuel becomes dominant and irradiation induced creep can be neglected. Fission gas induced porosity seems to accelerate fuel creep drastically. Recognizing the sensitivity of the fuel creep to the porosity, additional studies exploring this phenomenon and verifying published equations either experimentally or through computation may benefit the understanding of the annular fuel behavior.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Combustor with axially staged fuel injection

A combustor with axially staged fuel injection includes a plurality of nozzle segments annularly arranged about a center fuel nozzle. Each nozzle segment includes a fuel plenum partially defined between a forward plate and an aft plate and a plurality of tubes that extends through the fuel plenum and the aft plate. A panel fuel injector extends axially downstream from the aft plate and includes an outer wall, an inner wall, a plurality of outlets defined along at least one of the outer wall and the inner wall and a plurality of premix channels defined between the outer wall and the inner wall. Each premix channel is in fluid communication with a fuel supply, a compressed air supply and a respective outlet of the plurality of outlets.

42 ENGINEERING↗
DOE OSTI2019

Distributed fibre optic strain sensing of an axially deformed well model in the laboratory

Well integrity is crucial in enabling sustainable gas production from methane hydrate reservoirs and real-time distributed monitoring techniques can potentially facilitate proper and timely inspection of well integrity during gas production. Here in this research, the feasibility of distributed fibre optic strain monitoring with Brillouin optical time domain reflectometry/analysis (BOTDR/A) for well monitoring was examined by conducting a laboratory test on a well model subjected to axial tensile deformation, which occurs due to reservoir compaction during gas production. First, the validity of the proposed experimental methodology is assessed by a finite element analysis and theoretical modelling of a well subjected to reservoir compaction. A 3 m long well model is developed from the modelling and is instrumented with different types of fibre optic cables to measure the distributed strain development during tensile loading. Results show that the proposed well model and loading scheme can satisfactorily simulate the axial tensile deformation of the well in the laboratory condition. BOTDR is capable of capturing the tensile strain development of the well model accurately within the limitation of the spatial resolution of the BOTDR measurement. To enable accurate distributed strain monitoring of well deformation with BOTDR/A, the following issues are discussed: tightly buffered coating layers around optical fibre cores through mechanical compression and/or chemical adhesion, and a small number of coating layers.

42 ENGINEERING↗
DOE OSTI2012

DYNAMICS INSIDE THE RADIO AND X-RAY CLUSTER CAVITIES OF CYGNUS A AND SIMILAR FRII SOURCES

We describe approximate axisymmetric computations of the dynamical evolution of material inside radio lobes and X-ray cluster gas cavities in Fanaroff-Riley II (FRII) sources such as Cygnus A. All energy is delivered by a jet to the lobe/cavity via a moving hotspot where jet energy dissipates in a reverse shock. Our calculations describe the evolution of hot plasma, cosmic rays (CRs), and toroidal magnetic fields flowing from the hotspot into the cavity. Many important observational features are explained. Gas, CRs, and field flow back along the cavity surface in a 'boundary backflow' consistent with detailed FRII observations. Computed ages of backflowing CRs are consistent with observed radio-synchrotron age variations only if shear instabilities in the boundary backflow are damped and we assume this is done with viscosity of unknown origin. We compute a faint thermal jet along the symmetry axis and suggest that it is responsible for redirecting the Cygnus A nonthermal jet. Magnetic fields estimated from synchrotron self-Compton (SSC) X-radiation observed near the hotspot evolve into radio lobe fields. Computed profiles of radio-synchrotron lobe emission perpendicular to the jet reveal dramatically limb-brightened emission in excellent agreement with FRII observation, although computed lobe fields exceed those observed. Strong winds flowing from hotspots naturally create kiloparsec-sized spatial offsets between hotspot nonthermal X-ray inverse Compton (IC-CMB) emission and radio-synchrotron emission that peaks 1-2 kpc ahead where the field increases due to wind compression. In our computed version of Cygnus A, nonthermal X-ray emission increases from the hotspot (some IC-CMB, mostly SSC) toward the offset radio-synchrotron peak (mostly SSC).

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2011

Effect of nonuniform radial density distribution on the space charge dominated beam bunching

Beam dynamics of a space charge dominated beam during the bunch compression is studied self consistently for the case of fixed shape non-uniform bell shape and hollow shape density distributions in the transverse direction. We have used thick slices at different parts of the beam to account for variation in the beam radius in the study of the transverse dynamics. The longitudinal dynamics has been studied using the disc model. The axial variation of the radius of the slices and emittance growth arising from the phase dependence of the transverse rf forces are also included in the simulation. We have modified the beam envelope equation to take into account the longitudinal space charge effect on the transverse motion which arises due to the finite bunch size. To demonstrate the application of the theoretical formulations developed, we have studied a sinusoidal beam bunching system and presented detailed numerical results.

43 PARTICLE ACCELERATORS↗
DOE OSTI2020

3D Printing of Liquid Crystal Elastomer Foams for Enhanced Energy Dissipation Under Mechanical Insult

Polymer foams are an essential class of lightweight materials used to protect assets against mechanical insults, such as shock and vibration. Two features are important to enhance their energy absorption characteristics: the foam structure and the matrix phase mechanical behavior. This study investigates novel approaches to control both of these features to enhance the energy absorption capability of flexible lattice foams. First, we consider 3D printing via digital light processing (DLP) as a method to control the foam mesostructure across a suite of periodic unit cells. Second, we introduce an additional energy dissipation mechanism in the solid matrix phase material by 3D printing the lattice foams with polydomain liquid crystal elastomer (LCE), which undergo a mechanically induced phase transition under large strains. This phase transition is associated with LC mesogen rotation and alignment and provides a second mechanism for mechanical energy dissipation in addition to the viscoelastic relaxation of the polymer network. Here, we contrast the 3D printed LCE lattices with conventional, thermomechanically near-equivalent elastomer lattice foams to quantify the energy-absorbing enhancement the LCE matrix phase provides. Under cyclic quasi-static uniaxial compression conditions, the LCE lattices show dramatically enhanced energy dissipation in uniaxial compression compared to the non-LCE equivalent foams printed with a commercially available photocurable elastomer resin. The lattice geometry also plays a prominent role in determining the energy dissipation ratio between the LCE and non-LCE foams. We show that when increasing the lattice connectivity, the foam deformation transitions from bending-dominated to stretching-dominated deformations, which generates higher axial strains in the struts and higher energy dissipation in the lattice foam, as stretching allows greater mesogen rotation than bending. The LCE foams demonstrate superior energy absorption during the repeated dynamic loading during drop testing compared with the non-LCE equivalent foams, demonstrating the potential of LCEs to enhance physical protection systems against mechanical impact.

3D printing↗
DOE OSTI2017

Study on the residual stress relaxation in girth-welded steel pipes under bending load using diffraction methods

This research is dedicated to the experimental investigation of the residual stress relaxation in girth-welded pipes due to quasi-static bending loads. Ferritic-pearlitic steel pipes are welded with two passes, resulting in a characteristic residual stress state with high tensile residual stresses at the weld root. Also, four-point bending is applied to generate axial load stress causing changes in the residual stress state. These are determined both on the outer and inner surfaces of the pipes, as well as in the pipe wall, using X-ray and neutron diffraction. Focusing on the effect of tensile load stress, it is revealed that not only the tensile residual stresses are reduced due to exceeding the yield stress, but also the compressive residual stresses for equilibrium reasons. Furthermore, residual stress relaxation occurs both parallel and perpendicular to the applied load stress.

36 MATERIALS SCIENCE↗