Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ASH CONTENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Experimental study on NOx emission and unburnt carbon of a radial biased swirl burner for coal combustion

Pilot tests were carried out on a 1 MW thermal pulverized coal fired testing furnace. Symmetrical combustion was implemented by use of two whirl burners with dual air adjustment. The burnout air device was installed in various places at the top of the main burner, which consists of a primary air pipe with a varying cross-section and an impact ring. In the primary air pipe, the air pulverized coal (PC) stream was separated into a whirling stream that was thick inside and thin outside, thus realizing the thin-thick distribution at the burner nozzle in the radial direction. From the comparative combustion tests of three coals with relatively great characteristic differences, Shaanbei Shenhua high rank bituminous coal (SH coal), Shanxi Hejin low rank bituminous coal (HJ coal), and Shanxi Changzhi meager coal (CZ coal), were obtained such test results as the primary air ratio, inner secondary air ratio, outer secondary air ratio, impact of the change of outer secondary air, change of the relative position for the layout of burnout air, change of the swirling intensity of the primary air and secondary air, etc., on the NOx emission, and unburnt carbon content in fly ash (CFA). At the same time, the relationship between the NOx emission and burnout ratio and affecting factors of the corresponding test items on the combustion stability and economic results were also acquired. The results may provide a vital guiding significance to engineering designs and practical applications. According to the experimental results, the influence of each individual parameter on NOx formation and unburned carbon in fly ash agrees well with the existing literature. In this study, the influences of various combinations of these parameters are also examined, thus providing some reference for the design of the radial biased swirl burner, the configuration of the furnace, and the distribution of the air. 23 refs., 14 figs., 2 tabs.

01 COAL, LIGNITE, AND PEAT↗

Final Technical Report: Plasma Arc Gasification Based Rare Earth Element Recovery from Coal Fly Ash

Southern Research, as the primary awardee, with sub-awardees ArcSec Technologies, LLC (ArcSec) and Reaction Engineering International (REI) have investigated a plasma arc based thermal process intended to concentrate rare earth elements (REE) from coal fly ash. Successful demonstration of the technology would contribute to the effort for realizing a competitive, domestic REE value chain thereby reducing U.S. dependence on foreign supply, maintaining national security interests, and creating opportunities for economic growth. The originally proposed concept included two technology options – 1) a smelting process and 2) a smelting plus vaporization and condensation process. For both options, coal fly ash would be smelted in a plasma arc heated furnace under reducing conditions to separate ash into molten slag and reduced metal (primarily iron) phases. During smelting, it was expected that the REE would also be reduced to metals and partition mostly to the iron phase. During the first year of work, sample coal ash feedstocks were acquired and characterized, feasibility of the smelting process was evaluated in bench-scale experiments, and the vaporization/condensation process was investigated through equilibrium and CFD modeling studies. From the feedstock characterization, REE content for the coal ash samples obtained was measured to be in the range of 302 – 1219 ppm with average at 537 ppm. Though it was successfully demonstrated that ash could be separated into slag and metal phases, the bench-scale experiments were only marginally successful at collecting REE in the metal phase. Producing REE concentrates near the DOE goal of 2%, however, has not been achieved. From the modeling studies, the vaporization/condensation process was predicted to be effective for separating individual REE and producing enriched metal fractions with total REE content higher than 2%, provided the smelting process performed as intended. Supplemental smelting experiments and thermodynamic modeling studies, conducted during the second year of work, indicated a number of technical modifications that could lead to producing higher REE concentrates from coal ash. The strategy shifted to reducing as much of the ash oxides to metals as possible, leaving the REE more concentrated in the remaining slag. Results from later experiments based on the modified approach showed improvements in REE recovery and concentration levels in smelted products. SEM-EDS analyses on product specimens showed agglomerations of reduced metal REE crystals at much larger length-scales as compared to REE content in raw ash.

01 COAL, LIGNITE, AND PEAT↗

Fly ash properties and mercury sorbent affect mercury release from curing concrete

The release of mercury from concrete containing fly ashes from various generator boilers and powdered activated carbon sorbent used to capture mercury was measured in laboratory experiments. Release of gaseous mercury from these concretes was less than 0.31% of the total quantity of mercury present. The observed gaseous emissions of mercury during the curing process demonstrated a dependency on the organic carbon content of the fly ash, with mercury release decreasing with increasing carbon content. Further, lower gaseous emissions of mercury were observed for concretes incorporating ash containing activated carbon sorbent than would be expected based on the observed association with organic carbon, suggesting that the powdered activated carbon more tightly binds the mercury as compared to unburned carbon in the ash. Following the initial 28-day curing interval, mercury release diminished with time. In separate leaching experiments, average mercury concentrations leached from fly ash concretes were less than 4.1 ng/L after 18 h and 7 days, demonstrating that less than 0.02% of the mercury was released during leaching. 25 refs., 4 figs., 5 tabs.

01 COAL, LIGNITE, AND PEAT↗

Investigation of SiO{sub 2}:Na{sub 2}O ratio as a corrosion inhibitor for metal alloys

The silicate is one of the potential compounds used as a corrosion inhibitor for metal alloys. The mixture between silica and sodium hydroxide (NaOH) succeeded to produce the silicate product. The formulation of a silicate product normally variable depended by the different ratio of SiO{sub 2}:Na{sub 2}O. This research utilized the agriculture waste product of paddy using its rice husk. In this study, the amorphous silica content in rice husk ash was used after rice husk burnt in a muffle furnace at a certain temperature. The X-ray diffraction (XRD) analysis was done to determine the existence of amorphous phase of silica in the rice husk ash. There are several studies that recognized rice husk as an alternative source that obtained high silica content. The X-ray fluorescence (XRF) analysis was carried out to clarify the percentage amount of Si and O elements, which referred the silica compound in rice husk ash. The preparation of sodium silicate formulation were differ based on the SiO{sub 2}:Na{sub 2}O ratio (SiO{sub 2}:Na{sub 2}O ratio = 1.00, 2.00 and 3.00). These silicate based corrosion inhibitors were tested on several testing samples, which were copper (99.9%), aluminum alloy (AA 6061) and carbon steel (SAE 1045). The purpose of this study is to determine the appropriate SiO{sub 2}:Na{sub 2}O ratio and understand how this SiO{sub 2}:Na{sub 2}O ratio can affect the corrosion rate of each metal alloys immersed in acidic medium. In order to investigate this study, weight loss test was conducted in 0.5 M hydrochloric acid (HCl) for 24 hours at room temperature.

36 MATERIALS SCIENCE↗

Differences in gasification behaviors and related properties between entrained gasifier fly ash and coal char

In the study, two fly ash samples from Texaco gasifiers were compared to coal char and the physical and chemical properties and reactivity of samples were investigated by scanning electron microscopy (SEM), SEM-energy-dispersive spectrometry (EDS), X-ray diffraction (XRD), N{sub 2} and CO{sub 2} adsorption method, and isothermal thermogravimetric analysis. The main results were obtained. The carbon content of gasified fly ashes exhibited 31-37%, which was less than the carbon content of 58-59% in the feed coal. The fly ashes exhibited higher Brunauer-Emmett-Teller (BET) surface area, richer meso- and micropores, more disordered carbon crystalline structure, and better CO{sub 2} gasification reactivity than coal char. Ashes in fly ashes occurred to agglomerate into larger spherical grains, while those in coal char do not agglomerate. The minerals in fly ashes, especial alkali and alkaline-earth metals, had a catalytic effect on gasification reactivity of fly ash carbon. In the low-temperature range, the gasification process of fly ashes is mainly in chemical control, while in the high-temperature range, it is mainly in gas diffusion control, which was similar to coal char. In addition, the carbon in fly ashes was partially gasified and activated by water vapor and exhibited higher BET surface area and better gasification activity. Consequently, the fact that these carbons in fly ashes from entrained flow gasifiers are reclaimed and reused will be considered to be feasible. 15 refs., 7 figs., 5 tabs.

01 COAL, LIGNITE, AND PEAT↗

Biochars impact on soil moisture storage in an Ultisol and two Aridisols

Biochar additions to soils can improve soil water storage capability, however, there is sparse information identifying feedstocks and pyrolysis conditions that maximize this improvement. Nine biochars were pyrolyzed from five feedstocks at two temperatures and their physical and chemical properties were characterized. Biochars were mixed at 2% wt w{sup -1} into a Norfolk loamy sand (Fine-loamy, kaolinitic, thermic Typic Kandiudult), a Declo silt loam (Coarse-loamy, mixed, superactive, mesic xeric Haplocalcid), or a Warden silt loam (Coarse-silty, mixed, superactive, mesic xeric Haplocambid). Untreated soils served as controls. Soils were laboratory incubated in pots for 127 days and were leached about every 30 days with deionized water. Soil bulk densities were measured before each leaching event. For six days thereafter, pot holding capacities (PHC) for water were determined gravimetrically and were used as a surrogate for soil moisture contents. Water tension curves were also measured on the biochar treated and untreated Norfolk soil. Biochar surface area, surface tension, ash, C, and Si contents, in general, increased when produced under higher pyrolytic temperatures ({ge}500 C). Both switchgrass biochars caused the most significant water PHC improvements in the Norfolk, Declo and Warden soils compared to the controls. Norfolk soil water tension results at 5 and 60 kPa corroborated that biochar from switchgrass caused the most significant moisture storage improvements. Significant correlation occurred between the PHC for water with soil bulk densities. In general, biochar amendments enhanced the moisture storage capacity of Ultisols and Aridisols, but the effect varied with feedstock selection and pyrolysis temperature.

54 ENVIRONMENTAL SCIENCES↗

Effect of bed pressure drop on performance of a CFB boiler

The effect of bed pressure drop and bed inventory on the performances of a circulating fluidized bed (CFB) boiler was studied. By using the state specification design theory, the fluidization state of the gas-solids flow in the furnace of conventional CFB boilers was reconstructed to operate at a much lower bed pressure drop by reducing bed inventory and control bed quality. Through theoretical analysis, it was suggested that there would exist a theoretical optimal value of bed pressure drop, around which the boiler operation can achieve the maximal combustion efficiency and with significant reduction of the wear of the heating surface and fan energy consumption. The analysis was validated by field tests carried out in a 75 t/h CFB boiler. At full boiler load, when bed pressure drop was reduced from 7.3 to 3.2 kPa, the height of the dense zone in the lower furnace decreased, but the solid suspension density profile in the upper furnace and solid flow rate were barely influenced. Consequently, the average heat transfer coefficient in the furnace was kept nearly the same and the furnace temperature increment was less than 17{sup o}C. It was also found that the carbon content in the fly ash decreased first with decreasing bed pressure drop and then increased with further increasing bed pressure drop. The turning point with minimal carbon content was referred to as the point with optimal bed pressure drop. For this boiler, at the optimum point the bed pressure was around 5.7 kPa with the overall excess air ratio of 1.06. When the boiler was operated around this optimal point, not only the combustion efficiency was improved, but also fan energy consumption and wear of heating surface were reduced. 23 refs., 6 figs., 4 tabs.

01 COAL, LIGNITE, AND PEAT↗

Fly ash carbon passivation

A thermal method to passivate the carbon and/or other components in fly ash significantly decreases adsorption. The passivated carbon remains in the fly ash. Heating the fly ash to about 500 and 800 degrees C. under inert gas conditions sharply decreases the amount of surfactant adsorbed by the fly ash recovered after thermal treatment despite the fact that the carbon content remains in the fly ash. Using oxygen and inert gas mixtures, the present invention shows that a thermal treatment to about 500 degrees C. also sharply decreases the surfactant adsorption of the recovered fly ash even though most of the carbon remains intact. Also, thermal treatment to about 800 degrees C. under these same oxidative conditions shows a sharp decrease in surfactant adsorption of the recovered fly ash due to the fact that the carbon has been removed. This experiment simulates the various "carbon burnout" methods and is not a claim in this method. The present invention provides a thermal method of deactivating high carbon fly ash toward adsorption of AEAs while retaining the fly ash carbon. The fly ash can be used, for example, as a partial Portland cement replacement in air-entrained concrete, in conductive and other concretes, and for other applications.

36 MATERIALS SCIENCE↗

Comparative analysis of methods for determination of arsenic in coal and coal ash

In this paper the comparative analysis of different methods for the preparation and analysis of arsenic content in coal and coal ash have been presented. The suggested method is coal digestion method, i.e., coal ash digestion using the mixture of acids: nitric and sulphuric in presence of vanadium-pentoxide as catalyzer. The comparative analysis of different recording techniques (AAS-GH, AAS-GF and ICP-AES) has also been presented. For arsenic recording the suggested technique is AAS-GF technique. The obtained results show that the method of high precision, high sensitivity and high reproductivity has been obtained.

01 COAL, LIGNITE, AND PEAT↗

Tropical Red Macroalgae Cultivation with a Focus on Compositional Analysis

To create carbon efficient sources of bioenergy feedstocks and feedstuff for aquaculture and terrestrial livestock, it is critical to develop and commercialize the most efficient seaweed cultivation approach with a sustainable nutrient input supply. Here, we present data for a novel, onshore tropical macroalgae cultivation system, based on influent deep seawater as the nutrient and carbon sources. Two red algal species were selected, Agardhiella subulata and Halymenia hawaiiana, as the basis for growth optimization. Highest productivity in small-scale cultivation was demonstrated with A. subulata in the 10% deep seawater (64.7 µg N L−1) treatment, growing at up to 26% specific growth rate day−1 with highest yields observed at 247.5 g m−2 day−1 fresh weight. The highest yields for H. hawaiiana were measured with the addition of 10% deep seawater up to 8.8% specific growth rate day−1 and yields at 63.3 g fresh weight m−2 day−1 equivalent. Biomass should be culled weekly or biweekly to avoid density limitations, which likely contributed to a decrease in SGR over time. With a measured 30–40% carbon content of the ash-free dry weight (20–30% of the dry weight) biomass, this translates to an almost 1:1 CO2 capture to biomass ratio. The compositional fingerprint of the high carbohydrate content of both Agardhiella and Halymenia makes for an attractive feedstock for downstream biorefinery applications. By focusing on scaling and optimizing seaweed farming technologies for large-scale onshore farms, the opportunities for yield potential, adaptability to cultivation conditions, and meeting global sustainability goals through novel, carbon-negative biomass sources such as seaweed can be realized.

09 BIOMASS FUELS↗

Thermodynamic Model of COREX Melter Gasifier Using FactSage™ and Macro Facility

In the current study, the thermochemical model of the COREX melter gasifier has been developed using the FactSage™ thermodynamic software, and macro programming facility. The melter gasifier was conceptually divided into various equilibrium zones dealing with the reactions happening in the reactor. The coal char and the coke being used are divided among them optimally. The model has been validated with respect to the plant data for the hot-metal, slag, and reducing gas composition. The effects of the variation in the degree of metallization, on the final hot metal, slag, and reducing gas, have been predicted using this model. The variations in the process parameters for the different industrial coal grades used in the COREX plant have been determined. The effects of the volatile, ash, and the moisture contents of the coal on the hot-metal and the reducing gas compositions have been reported.

36 MATERIALS SCIENCE↗

Analysis of Changes in Thermomechanical Properties and Structure of Polyamide Modified with Fly Ash from Biomass Combustion

Study of performance of polyamide with fly ash addition with different contents of filler was carried out. In this article studies were performed: dynamical mechanical properties, thermal properties and structure research. The profiles of changes in the value of storage modulus E′ and tangent of mechanical loss angle tgδ depend on the temperature and frequency of vibrations. The crystallinity degree was examined using DSC methodology whereas the structure was analysed by means of the optical microscope. The increase in the value of storage modulus versus temperature and vibration frequency for the samples with addition of filler and the increase in the crystallinity degree and polymer matrix with reduced addition of fly ash were observed. A reduction in size of the structural components was also found, particularly for the composites with filler content. Graphical Abstract: .

09 BIOMASS FUELS↗

Fast Pyrolysis Behavior of Banagrass as a Function of Temperature and Volatiles Residence Time in a Fluidized Bed Reactor

A reactor was designed and commissioned to study the fast pyrolysis behavior of banagrass as a function of temperature and volatiles residence time. Four temperatures between 400 and 600°C were examined as well as four residence times between ~1.0 and 10 seconds. Pyrolysis product distributions of bio-oil, char and permanent gases were determined at each reaction condition. The elemental composition of the bio-oils and chars was also assessed. The greatest bio-oil yield was recorded when working at 450°C with a volatiles residence time of 1.4 s, ~37 wt% relative to the dry ash free feedstock (excluding pyrolysis water). The amounts of char (organic fraction) and permanent gases under these conditions are ~4 wt% and 8 wt% respectively. The bio-oil yield stated above is for 'dry' bio-oil after rotary evaporation to remove solvent, which results in volatiles and pyrolysis water being removed from the bio-oil. The material removed during drying accounts for the remainder of the pyrolysis products. The 'dry' bio-oil produced under these conditions contains ~56 wt% carbon which is ~40 wt% of the carbon present in the feedstock. The oxygen content of the 450°C, 1.4 s 'dry' bio-oil is ~38 wt%, which accounts for ~33 wt% of the oxygen in the feedstock. At higher temperature or longer residence time less bio-oil and char is recovered and more gas and light volatiles are produced. Increasing the temperature has a more significant effect on product yields and composition than increasing the volatiles residence time. At 600°C and a volatiles residence time of 1.2 seconds the bio-oil yield is ~21 wt% of the daf feedstock, with a carbon content of 64 wt% of the bio-oil. The bio-oil yield from banagrass is significantly lower than from woody biomass or grasses such as switchgrass or miscanthus, but is similar to barley straw. In conclusion, the reason for the low bio-oil yield from banagrass is thought to be related to its high ash content (8.5 wt% dry basis) and high concentration of alkali and alkali earth metals (totaling ~2.8 wt% relative to the dry feedstock) which are catalytic and increase cracking reactions during pyrolysis.

60 APPLIED LIFE SCIENCES↗

Evaluation and beneficiation of high sulfur and high alkali fly ashes for use as supplementary cementitious materials in concrete

Coal-fuel power plants with semi-dry or dry flue gas desulfurization (FGD) systems produce high sulfur and/or high alkali fly ashes due to comingling of fly ash with FGD products. Such fly ashes do not meet the SO 3 content limit (5.0% max.) of ASTM C618 or are unable to mitigate the alkali-silica reaction. The mineralogy of the sulfur present in these ashes can vary significantly (e.g., CaSO 4 , CaSO 3 , Na2SO 4 ) based on the FGD technology used and this affects the performance of these fly ashes in concrete. Thus, the single SO 3 % limit of ASTM C618 is unable to capture the complexity and performance of fly ash, and this results in elimination of potentially viable pozzolans for concrete. Here this study performs a systematic investigation of the effect of SO 3 type and content in fly ash on various performance parameters of cement-fly ash pastes and mortars, including workability (flow and flow retention), pore fluid pH, setting time, strength development, and potential for deleterious expansion. To better quantify and understand these effects, the study considers both real and doped fly ashes (i.e., a blend of specification-compliant fly ash with target sulfur compounds). The poor performance observed in the case of setting time and pore fluid pH was successfully mitigated using chemical admixtures.

36 MATERIALS SCIENCE↗

Trace element partitioning in ashes from boilers firing pure wood or mixtures of solid waste with respect to fuel composition, chlorine content and temperature

Highlights: • Different solids waste incineration is discussed in grate fired and fluidized bed boilers. • We explained waste composition, temperature and chlorine effects on metal partitioning. • Excessive chlorine content can change oxide to chloride equilibrium partitioning the trace elements in fly ash. • Volatility increases with temperature due to increase in vapor pressure of metals and compounds. • In Fluidized bed boiler, most metals find themselves in fly ash, especially for wood incineration. - Abstract: Trace element partitioning in solid waste (household waste, industrial waste, waste wood chips and waste mixtures) incineration residues was investigated. Samples of fly ash and bottom ash were collected from six incineration facilities across Sweden including two grate fired and four fluidized bed incinerators, to have a variation in the input fuel composition (from pure biofuel to mixture of waste) and different temperature boiler conditions. As trace element concentrations in the input waste at the same facilities have already been analyzed, the present study focuses on the concentration of trace elements in the waste fuel, their distribution in the incineration residues with respect to chlorine content of waste and combustion temperature. Results indicate that Zn, Cu and Pb are dominating trace elements in the waste fuel. Highly volatile elements mercury and cadmium are mainly found in fly ash in all cases; 2/3 of lead also end up in fly ash while Zn, As and Sb show a large variation in distribution with most of them residing in the fly ash. Lithophilic elements such as copper and chromium are mainly found in bottom ash from grate fired facilities while partition mostly into fly ash from fluidized bed incinerators, especially for plants fuelled by waste wood or ordinary wood chips. There is no specific correlation between input concentration of an element in the waste fuel and fraction partitioned to fly ash. Temperature and chlorine content have significant effects on partitioning characteristics by increasing the formation and vaporization of highly volatile metal chlorides. Zinc and cadmium concentrations in fly ash increase with the incineration temperature.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Radiological investigation of lignite ash. The case of the West Macedonia Lignite Center (Greece)

This article investigates the natural radioactivity of 26 ash samples, laboratory produced from lignite samples collected in the West Macedonia Lignite Center in Northern Greece. The activity concentrations of {sup 40}K, {sup 235}U, {sup 238}U, {sup 226}Ra, {sup 228}Ra, and 232Th were measured by spectroscopy and found four to five times higher than those in the original lignite samples. The radionuclides transfer factors depend on the characteristics of the combustion process and were found higher for {sup 232}Th, {sup 228}Ra, and 40K, because of their closer affinity with the inorganic fraction of the lignite. Compared with other results found in the published literature, the studied ash has relatively high content in radioactivity, but the resulting radiation dose from the radionuclide emissions in the West Macedonia Lignite Center do not contribute significantly to the total effective dose.

01 COAL, LIGNITE, AND PEAT↗

Coupled Hydrothermal Extraction and Ligand-Associated Swellable Glass Media Recovery of Rare Earth Elements from Coal Fly Ash (Final Report)

Wayne State University (WSU) researchers, in collaboration with the University of California-Los Angeles (UCLA) and Los Alamos National Laboratory (LANL), have successfully developed a new sorbent media used in a process that concentrated the rare earth content in a coal fly ash sample from southeast MI by >350×, resulting in >13 wt% REO powder. The project developed a new DTPA-associated media that was used to concentrate total REEs. This project demonstrated a coupled hydrothermal extraction and solid-liquid recovery process that produced REO powder from raw fly ash while nearly eliminating the use of organic solvents. The project successfully: 1) identified a commercially viable ash supply with >$2.5 M in REO value being deposited monthly, 2) hydrothermally extracted >77% of REEs in coal fly ash (20% more than acid alone), 3) developed a new sorbent media that was used to concentrate REEs, 4) and engineered a process that resulted in a >13 wt% REO powder. The media also demonstrates a selectivity for mid and heavy REEs over Ce and La and the potential for use in separating individual rare earth elements. An invention disclosure for the sorbent media has been filed with WSU and a patent application will be submitted in the near future. The project examined the potential to couple hydrothermal leaching of coal fly ash with the engineering of a custom ligand-associated media to provide an organic solvent-free method of extracting and recovering REEs. Fly ash feedstock was collected from Detroit area coal-fired power plants, characterized for REE content, and subjected to a bench-top batch hydrothermal leaching/dissolution process inside custom-build pressure reactors at Los Alamos National Laboratory (LANL). This process applied a dissolution technique previously developed to process spent nuclear fuel and other nuclear materials. The modified ash was acidified and the resulting leachate was enriched with REEs along with Ca, Al, and Si. Ligands known to be effective in lanthanide/actinide separation were evaluated based on a series of criteria such as selectivity and association to organosilica through hydrophobicity. Batch experiments were conducted to establish the best conditions (e.g., pH, eluent, etc.) and best ligand systems for the effective extraction of REEs from the alkaline feed solution obtained from the hydrothermal leaching process. Once the organosilica-ligand extraction media was developed for REE concentration, an acidic solution was used to back extract and concentrate the REEs into a heavily REE-laden strip solution. The REEs in the strip solution were precipitated with oxalate to produce rare earth oxides.

01 COAL, LIGNITE, AND PEAT↗

Sub-divertor fuel isotopic content detection limit for JET and its impact on ICRF core heating and DTE2 operation

The ability to detect and control fuel isotopic content down to a 1% concentration level is greatly important for the upcoming JET DTE2 campaign, as well as its associated TT and DD phases. A reduction of H minority concentration even from 2% down to 1% is shown in this paper to have significant impact on the effectiveness of ion cyclotron range of frequencies core heating, while the ability to maintain T or D concentration at or below 1% is critical to limiting fusion neutron generation in the DD and TT phases, correspondingly. The sub-divertor measurement of (global) isotopic concentration, based on Penning-activated optical spectroscopy, can deliver minimally this 1% detection for DTE2 as long as light collection from the Penning emission can be optimized and gradual window transmission deterioration can be minimized. Here, this is simulated with a statistical analysis developed to understand the uncertainty sources in the JET DTE1 data, as well as to guide the optimization of an upgraded, fuel-isotopic content (and helium-ash concentration) gas analysis system for the JET divertor in preparation for DTE2. While this random error can be reduced to allow measurement substantially below 1% concentration, analysis also shows a systematic error of up to 1% understood to be due to plasma–surface interactions in the Penning excitation, suggesting that 1% may still be the low-end limit for the sub-divertor measurement, unless a Penning-source conditioning approach is also developed.

fusion fuel isotopic content↗