Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ACCELERATOR MAGNETS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2017

Heat Treatment Optimization of Rutherford Cables for a 15 T Nb 3 Sn Dipole Demonstrator

FNAL has been developing a 15 T Nb 3 Sn dipole demonstrator for a future Very High Energy pp Collider based on an optimized 60-mm aperture 4-layer “cos-theta” coil. In order to increase magnet efficiency, we graded the coil by using two cables with same 15 mm width and different thicknesses made of two different Restacked Rod Process (RRP®) wires. Due to the non-uniform field distribution in dipole coils the maximum field in the inner coil will reach 15-16 T, whereas the maximum field in the outer coil is 12-13 T. In preparation for the 15 T dipole coil reaction, heat treatment studies were performed on strands extracted from these cables with the goal of achieving the best coil performance in the corresponding magnetic fields. Particularly, the effect of maximum temperature and time on the cable critical current was studied to take into account actual variations of these parameters during coil reaction. In parallel and in collaboration with OST, development was performed on optimizing Nb 3 Sn RRP® wire design and layout. Index Terms— Accelerator magnet, critical current density, Nb 3 Sn strand, Rutherford cable.

43 PARTICLE ACCELERATORS↗
DOE OSTI2022

Flex-PCB Quench Antenna Developments at FNAL

We report flexible printed-circuit-board-based quench antenna arrays have been developed at FNAL since 2017. They proved to be low-noise, low-cost, sensitive, and non-invasive sensors for quench characterization in superconducting magnets, having the potential to extend even to quench detection. Starting with applications of small area sensors of this type, we have explored feasibility for operations at high pressure, and have invested in multi-channel quench antenna arrays covering the complete area of the innermost magnet layer of the conductor. We've also tested and optimized sensor geometry and relative orientations to increase sensitivity and spatial resolution. Beyond developments of warm and cold bore antennas, we've progressed to concepts which attach quench antennas to the conductor surfaces of accelerator magnets. Multiple programs and projects at FNAL and collaborating institutions benefited from this work already and our plans target further extensions of capabilities and applicability of these devices. In this paper we present the logic behind the development steps taken so far, status of our work and direction of near-term research on quench antennas at Fermilab.

43 PARTICLE ACCELERATORS↗
DOE OSTI2018

Designs and Prospects of Bi-2212 Canted-Cosine-Theta Magnets to Increase the Magnetic Field of Accelerator Dipoles Beyond 15 T

The critical current density of Bi-2212 round wires has seen significant improvement over the past two years. We present the magnetic design and stress analysis of two Bi-2212 dipoles based on Canted-Cosine-Theta (CCT) technology using the state-of-the-art wires. The first design, based on a 19-strand Rutherford cable of θ0.8mm strands, is a two-layer dipole with a bore diameter of 40 mm and an outer diameter of 98.4 mm; it generates 5.4 T when operating in stand-alone configuration and 18.9 T in 15 T background field. The second design, based on a 13-strand Rutherford cable of θ0.8mm strands, is also a two-layer dipole with a bore diameter of 40 mm and an outer diameter of 81 mm; it generates 4.0 T when operating in stand-alone configuration and 17.8 T in 15 T background field. Normal stresses on the conductor in these magnets do not exceed 35 MPa when working under background field.Moreover, we propose a novel approach for increasing the efficiency of CCT magnets using keystoned Rutherford cable while removing the midplane ribs. with this method, it is possible to increase the efficiency of small radius CCT coils by 20%. We conclude that Bi-2212 can be used to increase the limit of accelerator magnet dipole fields beyond 15 T while managing stresses in the coils to acceptable levels.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2010

Brittle superconducting magnets: an equivilent strain model

To exceed fields of 10 T in accelerator magnets, brittle superconductors like A15 Nb{sub 3}Sn and Nb{sub 3}Al or ceramic High Temperature Superconductors have to be used. For such brittle superconductors it is not their maximum tensile yield stress that limits their structural resistance as much as strain values that provoke deformations in their delicate lattice, which in turn affect their superconducting properties. Work on the sensitivity of Nb{sub 3}Sn cables to strain has been conducted in a number of stress states, including uniaxial and multi-axial, producing usually different results. This has made the need of a constituent design criterion imperative for magnet builders. In conventional structural problems an equivalent stress model is typically used to verify mechanical soundness. In the superconducting community a simple scalar equivalent strain to be used in place of an equivalent stress would be an extremely useful tool. As is well known in fundamental mechanics, there is not one single way to reduce a multiaxial strain state as represented by a 2nd order tensor to a scalar. The conceptual experiment proposed here will help determine the best scalar representation to use in the identification of an equivalent strain model.

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

Variation of effective filament diameter, irreversibility field, anisotropy, and pinning efficiency in Bi-2212 round wires

Abstract In recent years Bi 2 Sr 2 CaCu 2 O x (Bi-2212) received increasing attention due to its round wire multifilamentary architecture, a unique feature in high- T c superconductor. In fact, round wires are preferable for magnet designs, including solenoids for nuclear magnetic resonance (NMR) or research purpose and accelerator magnets. However, due to the narrow over-pressure heat treatment conditions necessary to obtain high J c and to the peculiar microstructure of Bi-2212 wires, a full understanding of the correlations between the different properties has not yet been developed. In this paper we investigate the effect of a vital part of Bi-2212 optimization, the maximum heat-treatment temperature T max in the range of 885 °C–896 °C, on the variations of J c , effective filament diameter d eff , anisotropy γ , INTER- and intra-grain irreversibility fields and pinning energies U 0 , all critical parameters in unravelling the complex mix of vortex pinning and connectivity that ultimately determines the critical current density. We found that d eff of the higher J c wires heat-treated at lower temperature is much smaller than for the lower J c wires. Moreover, a systematic increase of the irreversibility field and a decrease of the intrinsic Bi-2212 anisotropy underpins the higher J c . The analysis of the pinning energies reveals that there is little sample-to-sample variation in the INTER-grain pinning, whereas in all samples the intra-grain pinning has an enhancement below ∼40–45 K becoming more and more evident with increasing J c . These results suggest that the overall J c performance are not only related to the wire microstructure and connectivity, which obviously affect the INTER-grain properties, but they are also intimately related to the intrinsic and intra-grain properties such as γ and U 0 .

Physics↗
DOE OSTI2020

HTS Quadrupole Magnet for the Persistent Current Mode Operation

In this work, a new high-temperature superconducting (HTS) quadrupole magnet with circular coils was designed and built at Fermilab. Several HTS coils were also investigated at the temperature of liquid nitrogen. The main goal of this activity was to investigate the coils and magnet operation in a persistent current mode to reduce accelerator magnets’ capital and operational expenses. To accomplish this, HTS short-circuit coils were used. In the paper, HTS coils and magnet design, fabrication, and tests were discussed. The magnetic field in the magnet aperture and the field decay when the magnet operated in the “frozen flux” mode were measured. The test and simulation results were compared, confirming the advantages of the proposed approach.

43 PARTICLE ACCELERATORS↗
DOE OSTI2015

Superconducting Magnets for Particle Accelerators

In this study, we summarize the evolution and contributions of superconducting magnets to particle accelerators as chronicled over the last 50 years of Particle Accelerator Conferences (PAC, NA-PAC and IPAC). We begin with an historical overview based primarily on PAC Proceedings augmented with references to key milestones in the development of superconducting magnets for particle accelerators. We then provide some illustrative examples of applications that have occurred over the past 50 years, focusing on those that have either been realized in practice or provided technical development for other projects, with discussion of possible future applications.

43 PARTICLE ACCELERATORS↗
DOE OSTI2020

The Application of Coordination to Magnetic Measurement Automation: An SSW System Example

Magnetic measurements are an integral part of the development cycle of accelerator magnets, a part which provides necessary feedback to drive design and manufacturing improvements and corrections. Automation of these measurements allows for reduction of human errors and reproducibility of measurements. Realization of automation via coordination that is separated at the architectural level from the functional code provides flexibility in defining measurement procedures and substantial extensibility. The described Single Stretched Wire (SSW) system herein is an implementation of such a solution with the use of a component-based framework designed to build a family of measurement systems.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Electron Acceleration during Macroscale Magnetic Reconnection

Here, the first self-consistent simulations of electron acceleration during magnetic reconnection in a macroscale system are presented. Consistent with solar flare observations, the spectra of energetic electrons take the form of power laws that extend more than two decades in energy. The drive mechanism for these nonthermal electrons is Fermi reflection in growing and merging magnetic flux ropes. A strong guide field suppresses the production of nonthermal electrons by weakening the Fermi drive mechanism. For a weak guide field the total energy content of nonthermal electrons dominates that of the hot thermal electrons even though their number density remains small. Our results are benchmarked with the hard x-ray, radio, and extreme ultraviolet observations of the X8.2-class solar flare on September 10, 2017.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

Collaborative Research: Effects of the magnetic field shear and flow shear on the kinetic physics and particle acceleration in relativistic magnetic reconnection (Final Report)

Magnetic reconnection is a fundamental plasma process that allows rapid changes of magnetic field topology and the conversion of magnetic energy into plasma kinetic energy. There has been a strong surge of interest in relativistic reconnection over the past few years in plasma astrophysics, but the rich physics of collisionless reconnection and its associated particle acceleration in the relativistic regime remain less studied compared to the non-relativistic counterparts. Magnetic reconnection in a realistic system is often accompanied with the magnetic field shear and shear flows. This setting is more general and likely the more common situation where most reconnection takes place. Within the past few decades, researchers had made significant progress in understanding how magnetic reconnection works under these conditions in the non-relativistic regime. However, how the effect of special relativity, among other effects, influences the dynamics of reconnection in the strongly magnetized astrophysical plasmas under these conditions is largely unknown. Our proposed research is to use fully kinetic simulations to understand kinetic physics and particle acceleration in relativistic magnetic reconnection in more realistic configurations and physical conditions. The primary goal of this project is to identify the fundamental effects caused by special relativity under the presence of field shear and flow shear.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

A Finite Element Study of Stress Reduction Techniques in REBCO HTS Conductor on a Round Cable (CORC) Cable

ReBCO high-temperature superconducting (HTS) tape is critical for achieving the high magnetic fields needed in next-generation particle accelerators. Enhancing the mechanical performance of ReBCO tape increases its critical current by reducing internal stress, especially in the superconducting layer. A finite element study examined how copper layer properties affect stress in ReBCO conductor on a round core (CORC) cables. The cable was modeled as a doubly supported beam under uniform compressive stresses."cable was modeled as a doubly supported beam under uniform load to simulate bending. A staged modeling approach from a single tape to a six-layer stack enabled validation and efficient parameter studies. Increasing the yield strength and Young s modulus of the copper layers reduced peak stress in the ReBCO layer. These results support development of improved tape stacks for high-field accelerator magnets

Mueller, Scott [Northern Illinois U.]↗
DOE OSTI2018

Electron and Proton Acceleration in Trans-relativistic Magnetic Reconnection: Dependence on Plasma Beta and Magnetization

Nonthermal electron acceleration via magnetic reconnection is thought to play an important role in powering the variable X-ray emission from radiatively inefficient accretion flows around black holes. The trans-relativistic regime of magnetic reconnection—where the magnetization σ, defined as the ratio of magnetic energy density to enthalpy density, is ~1—is frequently encountered in such flows. By means of a large suite of two-dimensional particle-in-cell simulations, we investigate electron and proton acceleration in the trans-relativistic regime. Additionally, we focus on the dependence of the electron energy spectrum on σ and the proton β (the ratio of proton thermal pressure to magnetic pressure). We find that the electron spectrum in the reconnection region is nonthermal and can be modeled as a power law. At low β, the slope, p, is independent of β and hardens with increasing σ as $p\simeq 1.8+0.7/\sqrt{\sigma }$. Electrons are primarily accelerated by the nonideal electric field at X-points, either in the initial current layer or in current sheets generated between merging magnetic islands. At higher values of β, the electron power law steepens, and the electron spectrum eventually approaches a Maxwellian distribution for all values of σ. At values of β near β max ≈ 1/4σ, when both electrons and protons are relativistically hot prior to reconnection, the spectra of both species display an additional component at high energies, containing a few percent of particles. Finally, these particles are accelerated via a Fermi-like process by bouncing between the reconnection outflow and a stationary magnetic island

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

Ultra-low magnetization and hysteresis loss in APC Nb 3 Sn superconductors

For the accelerator magnets of the next hadron collider, reducing superconductor persistent-current magnetization is not only important for achieving the desired field quality, but also crucial for its sustainability because the magnetization loss is the major heat load to the magnet cold mass. For conventional Nb 3 Sn conductors this requires reduction of effective subelement size (D eff ). For the restacked-rod-process (RRP ® ) conductors a physical subelement size (D sub ) as small as 35 µm (corresponding to a D eff close to 45 µm) can be reached, but at a significant price in J c . Another way to reduce the magnetization is by introducing artificial pinning centers (APC) using the internal oxidation approach. APC conductors outperform conventional Nb 3 Sn wires in two aspects: 1) higher J c at high fields, and 2) much lower J c and magnetization at low fields (e.g. below 5 T). Here, in this work we explored the fabricability of APC wires with small D sub . A 180-stack APC wire was produced and drawn to 0.7- and 0.5 mm diameters with good quality, with D sub s of 34 and 24 µm (D eff s of 36 and 25 µm), respectively. For the 34 µm-D sub wire, its non-Cu J c is higher than that of an RRP ® wire used for the High-Luminosity Large Hadron Collider (HL-LHC) project above 13 T (e.g. 36% higher at 4.2 K, 18 T), while its non-Cu magnetization at 1 T, ΔM(1 T), is only 29% of the RRP ® wire. Its non-Cu hysteresis loss for a cycle between 1 and 14 T, Q h (1–14 T), is 37% of the RRP ® wire. For the 24 µm-D sub wire, its non-Cu J c surpasses the HL-LHC RRP ® wire above 17.5 T, while its ΔM(1 T) and Q h (1–14 T) are only 17% and 23% of the RRP® wire, respectively. Its non-Cu Q h (±3 T) even meets the specification of the International Thermonuclear Experimental Reactor project.

Xu, X [Fermi National Accelerator Laboratory (FNAL↗
DOE OSTI2012

In situ calibration of rotating sensor coils for magnet testing

An in situ procedure for calibrating equivalent magnetic area and rotation radius of rotating coils is proposed for testing accelerator magnets shorter than the measuring coil. The procedure exploits measurements of magnetic field and mechanical displacement inside a reference quadrupole magnet. In a quadrupole field, an offset between the magnet and coil rotation axes gives rise to a dipole component in the field series expansion. The measurements of the focusing strength, the displacement, and the resulting dipole term allow the equivalent area and radius of the coil to be determined analytically. The procedure improves the accuracy of coils with large geometrical irregularities in the winding. This is essential for short magnets where the coil dimensions constrain the measurement accuracy. Experimental results on different coils measuring small-aperture permanent magnets are shown.

42 ENGINEERING↗
DOE OSTI2025

High Field Magnet Programme -- European Strategy Input

In this submission, we describe research goals, implementation, and timelines of the High Field Magnet Programme, hosted by CERN. The programme pursues accelerator-magnet R&D with low-temperature- and high-temperature superconductor technology with a main focus on the FCC-hh. Following a long tradition of magnet R&D for high-energy particle colliders, HFM R&D fosters important societal impact through synergies with other fields.

43 PARTICLE ACCELERATORS↗
DOE OSTI2016

Protection heater design validation for the LARP magnets using thermal imaging

Protection heaters are essential elements of a quench protection scheme for high-field accelerator magnets. Various heater designs fabricated by LARP and CERN have been already tested in the LARP high-field quadrupole HQ and presently being built into the coils of the high-field quadrupole MQXF. In order to compare the heat flow characteristics and thermal diffusion timescales of different heater designs, we powered heaters of two different geometries in ambient conditions and imaged the resulting thermal distributions using a high-sensitivity thermal video camera. We observed a peculiar spatial periodicity in the temperature distribution maps potentially linked to the structure of the underlying cable. Two-dimensional numerical simulation of heat diffusion and spatial heat distribution have been conducted, and the results of simulation and experiment have been compared. Imaging revealed hot spots due to a current concentration around high curvature points of heater strip of varying cross sections and visualized thermal effects of various interlayer structural defects. Furthermore, thermal imaging can become a future quality control tool for the MQXF coil heaters.

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

An Initial Look at the Magnetic Design of a 150 mm Aperture High-Temperature Superconducting Magnet With a Dipole Field of 8 to 10 T

High-temperature superconducting REBa 2 Cu 3 O 7-$x$ (rebco) conductors have the potential to generate a high magnetic field over a broad temperature range. The corresponding accelerator magnet technology, still in its infancy, can be attractive for future energy-frontier particle colliders such as a multi-TeV muon collider. To help develop the technology, we explore the requirements and potential characteristics of a rebco magnet, operating at 4.2 or 20 K, with a dipole field of 8-10 T in a clear aperture of 150 mm. We use the canted cos $\theta$ magnet configuration to reduce the electromagnetic stresses on the conductors. We present the resulting dipole fields, field gradients for combined-function cases, conductor stresses, magnet dimensions and conductor lengths. We also discuss the conductor performance that is required to achieve the target dipole field at 4.2 and 20 K. In conclusion, the information can provide useful input to the development of rebco magnet and conductor technology for collider-ring magnets in a muon collider.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗