Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “3D PRINTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Processing and properties of SiC composites made via binder jet 3D printing and infiltration and pyrolysis of preceramic polymer

The effect of polymer infiltration and pyrolysis (PIP) cycles with polycarbosiloxane on the microstructure, air leak rate, and properties of SiC composites manufactured by a combination of binder jet 3D printing and PIP are reported. The density, Young’s modulus and flexural strength of disk-shaped components increased with the number of PIP cycles. In the case of density, it increased from 2.05 g/cm 3 in one PIP cycle to 2.33 g/cm 3 after three PIP cycles, while values of flexural strength and Young’s modulus at room temperature after three PIP cycles reached 66.8 ± 2.5 MPa and 69.5 ± 2.8 GPa, respectively. Conversely, the air leak rate was found to decrease with number of PIP cycles, and it reached a value of 4 mbar-liter/s after three cycles. The instantaneous coefficient of thermal expansion of the composite was found to change minimally with the number of PIP cycles and had a value of 4 ± 1.2 ppm/°C between 200°C and 1,000°C. Thermal conductivity was found to increase with number of PIP cycles and to decrease with temperature. For example, after 3 PIP cycles it was found to change from 6.72 ± 0.08 to 6.98 ± 0.08 W/mK at 25°C and 7.36 ± 0.08 to 7.96 ± 0.08 W/mK at 300°C. These values were lower than those of crystalline SiC because of the amorphous nature of the matrix and the presence of pores and cracks.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Understanding Fracture Aperture and Permeability Evolution due to Carbonate Mineralization Utilizing 3D Printing

Caprock formations are a crucial part of subsurface-engineered systems. Composed largely of shale, caprocks act as natural barriers that prevent the upward migration of fluids, thereby ensuring the containment of stored substances in subsurface formations. Fractures in these formations are potential leakage pathways for stored fluids. Mineral precipitation reactions in these fractures, particularly calcite, can significantly restrict the fluid permeability, reducing leakage potential. However, predictive capabilities of mineral precipitation in fractures and associated permeability evolution are limited due to a lack of fundamental understanding of such reactions in natural samples, complicated by mineral heterogeneity and the complexity of the fracture structure. In this study, 3D-printed fracture samples are used to understand the impact of carbonate mineralization on fracture aperture and permeability evolution. Samples were printed using a digital light processing (DLP) 3D printer and commercial liquid resin. Calcite precipitation was first tested on printed 2D films before conducting plug flow column experiments aimed to understand fracture permeability changes due to mineral precipitation. Contact angle measurement and Fourier transform infrared (FTIR) spectroscopy on printed 2D films show evidence of a substantial amount of surface energy for calcite nucleation and precipitation. Surface topography analysis of printed fractured surfaces reveals comparable values, highlighting the high replicability of the printed samples. During the column experiments, the permeability reduces exponentially due to a decrease in fracture aperture. Reductions in fracture aperture estimated from effluent concentration and 3D X-ray computed tomography (CT) show comparable results. Moreover, 3D X-ray CT images suggest the impact of local flow velocities on precipitation. The insights gained from this research contribute to a deeper understanding of the permeability evolution due to carbonate mineralization in caprock formations.

3D printing↗
DOE OSTI2024

Fabrication of 3D-printed copper based zinc anodes

The production of a porous copper-zinc structure includes providing copper ink, creating a 3D model of the porous copper-zinc structure, 3D printing the copper ink into a porous copper lattice structure using the 3D model, heat treatment of the porous copper lattice structure producing a heat treated porous copper lattice structure, surface modification of the heat treated porous copper lattice structure by nanowires growth on the heat treated porous copper lattice structure producing a heat treated porous copper lattice structure with nanowires, and electrodeposition of zinc onto the heat treated porous copper lattice structure with nanowires to produce the porous copper-zinc structure.

Zhu, Cheng↗
DOE OSTI2022

Qualification of Continuous Fiber Reinforced 3D Printed Material for use in Hot Cell Environments

The ability to employ additively manufactured polymers in highly radioactive environments facilitates rapid prototyping as well as emergency replacement of various equipment components contained in-cell. A technical evaluation (TEV) exists seeking to qualify 3D printed polymers and carbon reinforcements for use in-cell, the data generated in this project seeks to support the TEV. The goal of the study is to determine if the loss in mechanical properties is low enough to justify semi-permanent use in-cell.

3D printing↗
DOE OSTI2024

3D-Printed Porous Supramolecular Sorbents for Cobalt Recycling

Electronic waste recycling is a recognized global challenge that requires new strategies to bind and release critical materials selectively, such as cobalt present in lithium-ion batteries. To address this challenge, hierarchical 3D-printed porous polymer scaffolds bearing supramolecular receptors were prepared using vat photopolymerization and their cobalt binding profiles were examined as a function of matrix polarity. By combining high-resolution digital light processing (DLP) with polymerization-induced phase separation (PIPS), functional acrylic copolymer networks with micrometer-level precision of geometry and nanometer-level pores were generated. Covalent integration of a methacrylate-functionalized bisdicyclohexyl acetamide (BDCA-MA) receptor enabled binding and release of cobalt(II) chloride (CoCl 2 ) via a solvent polarity switch mechanism involving a change in solvent from ethanol to water. The present structures proved reusable as shown by sustained high binding efficiency over five bind and release cycles. Finally, this platform represents a “green” and energy conscious method for future electronic waste recycling.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Small Animal IMRT Using 3D-Printed Compensators

Preclinical radiation replicating clinical intensity modulated radiation therapy (IMRT) techniques can provide data translatable to clinical practice. For this work, treatment plans were created for oxygen-guided dose-painting in small animals using inverse-planned IMRT. Spatially varying beam intensities were achieved using 3-dimensional (3D)-printed compensators.

3D PRINTING↗
DOE OSTI2023

Digital Light Processing (DLP): 3D printing of polymer-based graphene oxide nanocomposites—Efficient antimicrobial material for biomedical devices

Bacterial infections are one of the major causes of surgical implant inefficiency and failure. Herein, we present a Nanocomposite (NC) produced by the addition of Poly(N-vinyl carbazole)-Graphene Oxide dispersion (PVK-GO) as a nanofiller to a commercial photopolymer acrylate resin and 3D printed as coatings via the Digital Light Processing technique. Characterization and bioassay results against Escherichia coli and Staphylococcus aureus confirmed the elevated thermomechanical properties and efficient antibacterial activity of the printed NC-based coatings. In conclusion, the present study demonstrates the fabrication and optimization of a PVK-GO-based NC and its potential utilization as a 3D-printable material for biomedical applications.

2D materials↗
DOE OSTI2024

Radio Frequency Properties of a 3D Printed Klystron Circuit

The manufacturing of active RF devices like klystrons is dominated by expensive and time-consuming cycles of machining and brazing. In this article, we characterize the RF properties of X-band klystron cavities and an integrated circuit manufactured with a novel additive manufacturing process. Parts are 3D printed in 316 L stainless steel with direct metal laser sintering, electroplated in copper, and brazed in one simple braze cycle. Stand-alone test cavities and integrated circuit cavities were measured throughout the manufacturing process. The un-tuned cavity frequency varies by less than 5% of the intended frequency, and Q factors reach above 1200. A tuning study was performed, and unoptimized tuning pins achieved a tuning range of 138 MHz without compromising Q. Klystron system performance was simulated with as-built cavity parameters and realistic tuning. Together, these results show promise that this process can be used to cheaply and quickly manufacture a new generation of highly integrated high power vacuum devices.

3D printing↗
DOE OSTI2023

Failure analysis of nuclear transient-tested UN tristructural isotropic fuel particles in a 3D printed SiC matrix

Fully ceramic microencapsulated fuel elements containing UN tristructural isotropic (TRISO) fuel particles within a 3D printed SiC matrix were subjected to transient testing with varying energy depositions. Detailed post-irradiation examinations were performed, including leaching in hot HNO3 and post-leaching X-ray computed tomography, to quantify the percentage of failed TRISO particles and crack propagation within the particles and surrounding fuel matrix. In parallel, detailed finite element analyses were performed for comparison with experimental findings and to better evaluate transient failure modes. The lowest transient energy deposition—which still exceeded bounding values for high-temperature gas-cooled reactor applications—resulted in no detectable TRISO particle failures or matrix cracking, which was consistent with the simulations. Simulations of the higher-energy transients for which significant TRISO particle failure was expected were generally able to reproduce the transient temperatures and matrix cracking. Thus, the TRISO particle failures were explained based on the effects of local SiC matrix thickness and porosity. Results generally confirmed the high strength of the additively manufactured SiC matrix but also affirmed the need for a modified UN TRISO architecture to prevent SiC matrix cracks from propagating through TRISO layers. This unique failure mode has not historically been considered for TRISO fuels contained in weaker graphite matrices.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS2017

A Ground-Based Study on Extruder Standoff Distance for the 3D Printing in Zero Gravity Technology Demonstration Mission

Analysis of phase I specimens produced as part of the 3D printing in zero G technology demonstration mission exhibited some differences in structure and performance for specimens printed onboard the International Space Station (ISS) and specimens produced on the ground with the same printer prior to its launch. This study uses the engineering test unit for the printer, identical to the unit on ISS, to conduct a ground-based investigation of the impact of the distance between the extruder tip and the build tray on material outcomes. This standoff distance was not held constant for the phase I flight prints and is hypothesized to be a major source of the material variability observed in the phase I data set.

Prater, T. J.↗
DOE OSTI2024

Electrical, thermal, and mechanical properties of spatially tailored fiber orientations in 3D printed carbon-carbon composites for EFAS/SPS

Using C-C synthesized at INL from continuous fiber 3D printed preforms, tooling was fabricated, tested, and compared to graphite. The anisotropic properties of the C-C material were leveraged to make stronger and more energy efficient tooling. Future work involves tailoring the fiber orientations to create targeted heating zones and thermal gradients.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A custom 3D printed paddlewheel improves growth in flat panel photobioreactor

One of the main challenges with using flat panel photobioreactors for algal growth is uneven mixing and settling of cells in corners, especially when bubbling is the only method used for mixing. Here, in order to improve mixing in our flat panel reactor, we designed a custom paddlewheel. Paddlewheels are frequently used in outdoor algae raceway ponds to improve mixing and we are taking advantage of the same principle for mixing in the reactor. The paddlewheel is easily integrated into our PSI FMT150 1‐L flat panel photobioreactor and is printed on a 3D printer using high temperature poly lactic acid (HT‐PLA). With the inclusion of an annealing step, the paddlewheel is autoclavable. Addition of the paddlewheel in the reactor minimized cell settling and improved algal growth, as evidenced by a nearly 40% increase in oxygen production rates. Nutrient dispersion and utilization in the culture was also improved as evidenced by a corresponding 38% decrease in CO 2 concentration. The paddlewheel device presented here is a cost‐effective method for improving algal growth in a flat panel photobioreactor.

09 BIOMASS FUELS↗
DOE OSTI2022

Efficient carbon capture using sub-textured polymer packing surfaces via 3D printing

Gas absorption is a common unit operation whose performance deeply relies on the gas liquid contact behavior. In this work, we report a solid polymeric surface feature containing microscale striation to improve the solid-liquid and gas-liquid contact and facilitate mass transfer. As a proof of concept, the surface feature is adopted for CO 2 capture absorber packing via 3D printing. Besides traditional embossing texture, an additional laminar striation is applied to the packing surface as a sub-texture. The packing shows notable CO 2 mass transfer increase without interfering with other key operating characteristics including pressure drop and liquid holdup. The improvement is based on the synergy of favorable wettability, thin liquid film and increased liquid mixing from rougher surface. In the demonstration test, the packing height could decrease by 33% using the advanced packing with same CO 2 removal, leading to a significant decrease in equipment size and capital expense for commercial CO 2 capture systems.

3D printing↗
DOE OSTI2023

Photo-Curing 3D Printing of Thermosetting Sacrificial Tooling for Fabricating Fiber-Reinforced Hollow Composites

Carbon fiber-reinforced hollow composites play a vital role in lightweighting modern cars and aircrafts. Fabrication of such hollow composites with seamless internal finish requires sacrificial tooling that can be used under pressure and high temperature. For the very first time, high performance sacrificial tooling that can be used to fabricate fiber-reinforced hollow composites is produced using photocuring 3D printing technology. This is achieved by developing UV-curable resins containing highly soluble yet hydrolysable acetal acrylate cross-linker and hydrophilic 4-acryloylmorpholine monomer. It is found that the cross-linker content greatly affects the printing speed. Further, the widely adopted UV post-curing method is found to have negligible impact on improving the thermal-mechanical properties of printed structures. Additionally, after thermal post-treatment, printed sacrificial tooling exhibits a heat deflection temperature of 112 °C at 0.455 MPa and an average coefficient of linear thermal expansion of 59 ppm °C -1 between 30 and 100 °C. As a result, printed tooling enables fabrication of carbon fiber-reinforced hollow composites with complex geometry, which shows a tensile strength of 802 MPa and an elastic modulus of 50.2 GPa.

36 MATERIALS SCIENCE↗
DOE OSTI2022

3D printing of a recycled copolyester of terephthalic acid, cyclohexanedimethanol and tetramethylcyclobutanediol

2,2,4,4-Tetramethyl-1,3-cyclobutanediol (TMCD) is a diol monomer for terephthalic acid (TPA) class of copolyesters that can increase the glass transition temperature and mechanical strength in comparison to conventional TPA polyesters. TMCD-modified poly (1,4-cyclohexylenedimethylene terephthalate) (PCTT) has been used to manufacture consumer products with good toughness, heat resistance and clarity. However, the suitability of PCTT in 3D printing had not been evaluated. Therefore, consumer plasticware was used as the starting material to investigate the suitability of this copolyester for fused deposition modeling (FDM). Here, chemical structure, mechanical properties, thermal behavior and viscoelastic properties of this copolyester were studied. NMR spectroscopy found that the copolyester had cyclohexanedimethanol (CHDM) and TMCD contents at 76.5 mol% and 20 mol% of total diol, respectively. 280 °C printing temperature and 110 °C bed temperature were suitable conditions for printing. T g of PCTT was 103 °C (25 °C higher than PETG). Young's modulus and impact strength of printed PCTT were at least 100% and 65% higher than printed PETG, respectively. The ease of printing, superior mechanical properties and T g (103 °C) make the PCTT random copolyester highly applicable in additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2020

3D printed graphene-based self-powered strain sensors for smart tires in autonomous vehicles

The transition of autonomous vehicles into fleets requires an advanced control system design that relies on continuous feedback from the tires. Smart tires enable continuous monitoring of dynamic parameters by combining strain sensing with traditional tire functions. Here, we provide breakthrough in this direction by demonstrating tire-integrated system that combines direct mask-less 3D printed strain gauges, flexible piezoelectric energy harvester for powering the sensors and secure wireless data transfer electronics, and machine learning for predictive data analysis. Ink of graphene based material was designed to directly print strain sensor for measuring tire-road interactions under varying driving speeds, normal load, and tire pressure. A secure wireless data transfer hardware powered by a piezoelectric patch is implemented to demonstrate self-powered sensing and wireless communication capability. Combined, this study significantly advances the design and fabrication of cost-effective smart tires by demonstrating practical self-powered wireless strain sensing capability.

33 ADVANCED PROPULSION SYSTEMS↗