Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “virtual engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

Simulations of Multi-Mode Combustion Regimes Realizable In a Gasoline Direct Injection Engine

Lean and dilute gasoline compression ignition (GCI) operation in spark ignition (SI) engines are an attractive strategy to attain high fuel efficiency and low NOx levels. However, this combustion mode is often limited to low-load engine conditions due to the challenges associated with autoignition controllability. In order to overcome this constrain, multi-mode (MM) operating strategies, consisting of advanced compression ignition (ACI) at low load and conventional SI at high load, have been proposed. In this three-dimensional computational fluid dynamics study, the concept of multi-mode combustion using two RON98 gasoline fuel blends (Co-Optima Alkylate and E30) in a gasoline direct injection (GDI) engine were explored. To this end, a new reduced mechanism for simulating the kinetics of E30 fuel blend is introduced in this study. To cover the varying engine load demands for multi-mode engines, primary combustion dynamics observed in ACI and SI combustion modes was characterized and validated against experimental measurements. In order to implement part-load conditions, a strategy of mode transition between SI and ACI combustion (i.e., mixed-mode combustion) was then explored numerically by creating a virtual test condition. The results obtained from the mixed-mode simulations highlight an important feature that deflagrative flame propagation regime coexists with ignition-assisted end-gas autoignition. This study also identifies a role of turbulent flow property adjacent to premixed flame front in characterizing the mixed-mode combustion. The employed hybrid combustion model was verified to perform simulations aiming at suitable range of multi-mode engine operations.

Kim, Sayop↗

Optimized V1G and V2G Electric Vehicle Fleet Management and Grid Transaction at Marine Corps Air Station Miramar in San Diego, CA

The overall technical goal of the project was to demonstrate an all-electric bi-directional non-tactical fleet at Marine Corps Air Station (MCAS) Miramar that was integrated and controlled with other distributed energy resources (DERs) (i.e., PV, stationary battery, and building loads) to provide resilience to critical electric loads in the event of grid outages, to minimize charging costs, and to provide economic energy resources to electricity markets. In this project, the specific, technical objectives were: 1. Demonstrate that bi-directional electric vehicles can provide critical complementary services to fixed storage batteries in microgrid applications while performing function as non-tactical vehicles. 2. Demonstrate participation of bi-directional (V2G) and unidirectional (V1G) PEVs for demand management and minimization of charging costs. 3. Demonstrate integration of multiple DERs for grid service participation. US Marine Corps Air Station (MCAS) Miramar in San Diego was the site of this electric vehicle-to-microgrid-utility grid test and demonstration project. Existing microgrid assets in this study included (1) a public works building; (2) a 30-kW rooftop photovoltaic (PV) system and (3) a separate 250 kW carport PV system. In this project, six bi-directional V2G vans were located at the MCAS Miramar’s showcase building-scale microgrid to develop and test technical capabilities that V2G can provide in microgrid applications (e.g., cost reduction and resiliency). These resources provided aggregated demand management and simulated participation in current retail DR programs. The vehicles used in this demonstration were selected because they provided functionality that MCAS Miramar needed, 15 passenger transport and facilities work cargo carrying capacity, and bi-directional charging capability that the research project required. All vehicles in this study were manufactured and distributed by VIA Motors, Inc. There were six vehicles total and each was VIA’s VTRUX eREV V2G model, a modified General Motors Chevrolet 2500 2WD van. Three of the vans were configured as passenger vans and the other three were configured as cargo vans. Each van had an on-board bi-direcrtional inverter/charger, Bel Power Solutions model 350INVCHGT150-120-240-8G nominally rated at +/-15 kW. The VIA van’s charging connector follows the J1772 charging protocol. The bi-directional EVSEs demonstrated in this study were manufactured by Coritech, Inc. Each VGI-80-AC charging station enabled enhanced V2G charging capability to a Clipper Creek CS-100 charging module. The enhanced capabilities included ethernet communication following the SEP2.0 protocol with a distributed energy resource function set and an operator screen displaying real-time SOC, voltage, and current. The VGI-80-AC charging stations are classified as level 2 with a maximum current output of 80 A or effectively 19 kW. The VIA van’s onboard charger limited the charging and discharging power to 15 kW in each direction. A control computer was installed in the EWOC and connected to an existing monitor. The V2G control communication network was a completely stand-alone closed system that did not have any connection to any other networks on the base. A cybersecure remote communication connection was created with a cellular modem, firewall hardware, and a virtual private network configuration.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Modeling of the Indentation of Fiber Reinforced Materials Using Spherical Indenters

Following the enormous development of the technology there is a great need for complex engineering materials to be studied in multilayered films at the nano-level. Careful modeling of the structure of engineering materials, using finite element analysis may reveal specific behavior of the component materials and the filling materials, such as mortars, which are the important boundaries of all the engineering materials. The instruments used for experiments are expensive and their utilization is hindered by many unexpected factors. With the help of computer programs it is possible to achieve virtual nanoindentation, a widely known non-destructive method. It is easy to model structures in whatever shape or dimensions we wish, with one or more layers and with linear or nonlinear materials in order to obtain stress, strain, displacement curves, study microhardness, etc. The purpose of this paper is to model the nanoindentation process for fiber-reinforced concrete and to study the mechanical properties as a function of the distance of a particular fibre.

36 MATERIALS SCIENCE↗

Cooperative Research and Development Agreement among National Energy Technology Laboratory, The Board of Regents of the University System of Georgia by and on behalf of Georgia Institute of Technology, and University of Texas at El Paso [Abstract]

Georgia Institute of Technology (GIT), University of Texas at El Paso (UTEP), and the National Energy Technology Laboratory (NETL) will collaborate and develop cyber-physical systems for advanced power systems. GIT will test virtual models on hybrid power system hardware and cyber physical components. UTEP will test novel actuators on hybrid power system hardware. NETL will access GIT’s expertise in the engineering and real time simulation of power system processes for cyber-physical systems and simulations to control hardware. NETL will establish a relationship to promote UTEP’s capabilities in additive manufacturing and high-temperature piezo-electric devices with the potential for controlling high-temperature flows with a light and inexpensive device at high response rates. This project is the result of an EERE Advanced Manufacturing Office open Multi-Topic awarded proposal led by GIT titled, “Robust Combined Heat and Hybrid Power (CHHP) for High Electrical Efficiency Cogeneration”.

42 ENGINEERING↗

A Machine Learning-Genetic Algorithm (ML-GA) Approach for Rapid Optimization Using High-Performance Computing

A Machine Learning-Genetic Algorithm (ML-GA) approach was developed to virtually discover optimum designs using training data generated from multi-dimensional simulations. Machine learning (ML) presents a pathway to transform complex physical processes that occur in a combustion engine into compact informational processes. In the present work, a total of over 2000 sector-mesh computational fluid dynamics (CFD) simulations of a heavy-duty engine were performed. These were run concurrently on a supercomputer to reduce overall turnaround time. The engine being optimized was run on a low-octane (RON70) gasoline fuel under partially premixed compression ignition (PPCI) mode. A total of nine input parameters were varied, and the CFD simulation cases were generated by randomly sampling points from this nine-dimensional input space. These input parameters included fuel injection strategy, injector design, and various in-cylinder flow and thermodynamic conditions at intake valve closure (IVC). The outputs (targets) of interest from these simulations included five metrics related to engine performance and emissions. Over 2000 samples generated from CFD were then used to train an ML model that could predict these five targets based on the nine input features. A robust super learner approach was employed to build the ML model, where results from a collection of different ML algorithms were pooled together. Thereafter, a stochastic global optimization genetic algorithm (GA) was used, with the ML model as the objective function, to optimize the input parameters based on a merit function so as to minimize fuel consumption while satisfying CO and NOx emissions constraints. The optimized configuration from ML-GA was found to be very close to that obtained from a sequentially performed CFD-GA approach, where a CFD simulation served as the objective function. In addition, the overall turnaround time was (at least) 75% lower with the ML-GA approach, as the training data was generated from concurrent CFD simulations and employing the ML model as the objective function significantly accelerated the GA optimization. Finally, this study demonstrates the potential of ML-GA and high-performance computing (HPC) to reduce the number of CFD simulations to be performed for optimization problems without loss in accuracy, thereby providing significant cost savings compared to traditional approaches.

97 MATHEMATICS AND COMPUTING↗

Comparison of Virtual Oscillator and Droop Control: Preprint

Virtual oscillator control and droop control are two techniques that can be used to ensure synchronization and power sharing of parallel inverters in islanded operation. VOC relies on the implementation of non-linear Van der Pol oscillator equations in the control system of the inverter, acting upon the time-domain instantaneous inverter current and terminal voltage. On the other hand, DC explicitly computes active and reactive power produced by the inverter and relies on limited bandwidth low-pass filters. Even though both methods can be engineered to produce the same steady-state characteristics, their dynamic performances are significantly different. This paper presents analytical and experimental results that aim to compare both methods. It is shown that VOC is inherently faster and enables minimizing the circulating currents. The results are verified using three 120V, 1kW inverters.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Integrating CO2 Electrolysis with Gas Fermentation to Produce Valuable Fuels and Chemicals

Many industrial activities squander CO2, decreasing process yield. We envision a future where this waste carbon is instead captured, upgraded, and valorized directly at the point of emission. Within the CO2 Reduction and Upgrading Consortium (a collaboration of seven US national laboratories and industrial partners), we are pursuing this goal by developing and de-risking new technologies for low temperature CO2 electrolysis, coupled with biological upgrading of intermediates into more valuable compounds. One such process involves electrocatalytic reduction of CO2 to generate carbon monoxide (CO). As both a carbon and energy source, CO represents an attractive feedstock for microbial upgrading by certain syngas-fermenting species, such as the autotrophic bacterium Clostridium autoethanogenum. Our team has developed new genetic tools and optimized cultivation techniques to enhance C. autoethanogenum as a platform host for the biological conversion of syngas into value-added products. For example, we have created novel CRISPR-based genetic engineering techniques to build new, genome-reduced, platform strains of C. autoethanogenum with improved growth rates. Further, we ve introduced heterologous biochemical pathways into C. autoethanogenum to enable the production of high-value compounds from syngas, such as the isoprenoid precursor mevalonic acid. With the tools of electrochemistry and synthetic biology, there is virtually no limit to the spectrum of products that could be sustainably manufactured from CO2.

09 BIOMASS FUELS↗

BEAM SIMULATIONS USING VIRTUAL DIAGNOSTICS FOR THE DRIVER LINAC

End-to-end beam simulations for the driver linac have shown that the design meets the necessary performance requirements including having adequate transverse and longitudinal acceptances. However, to achieve reliable operational performance, the development of appropriate beam diagnostic systems and control room procedures are crucial. With limited R&D funding, beam simulations provide a cost effective tool to evaluate candidate beam diagnostic systems and to provide a critical basis for developing early commissioning and later operational activities. We propose to perform beam dynamic studies and engineering analyses to define the requisite diagnostic systems of the driver linac and through simulation to develop and test commissioning and operational procedures.

43 PARTICLE ACCELERATORS↗

Denoising atomic resolution 4D scanning transmission electron microscopy data with tensor singular value decomposition

Tensor singular value decomposition (SVD) is a method to find a low-dimensional representation of data with meaningful structure in three or more dimensions. Here, tensor SVD has been applied to denoise atomic-resolution 4D scanning transmission electron microscopy (4D STEM) data. On data simulated from a SrTiO 3 [100] perfect crystal and a Si [110] edge dislocation, tensor SVD achieved an average peak signal-to-noise ratio (PSNR) of ~40 dB, which matches or exceeds the performance of other denoising methods, with processing times at least 100 times shorter. On experimental data from SrTiO 3 [100] and LiZnSb [11 2 ¯ 0]/GaSb [110] samples, tensor SVD denoises multiple GB 4D STEM data sets in ten minutes on a typical personal computer. Denoising with tensor SVD improves both convergent beam electron diffraction patterns and virtual-aperture annular dark field images.

36 MATERIALS SCIENCE↗

A simple, high-yield, apparatus for NEG coating of vacuum beamline elements

Non-Evaporable Getter (NEG) materials are extremely useful in vacuum systems for achieving Ultra High Vacuum. Recently, these materials have been used to coat the inner surfaces of vacuum components, acting as an internal, passive, vacuum pump. We have constructed a low cost apparatus, which allows coating of very small diameter vacuum tubes, used as differential pumping stages. Despite the relative ease of construction, we are routinely able to achieve high coating yields. We further describe an improvement to our system, which is able to achieve the same yield, at an even lower complexity by using an easily manufactured permanent magnet arrangement. The designs described are extendible to virtually any combination of length and diameter of the components to be coated.

42 ENGINEERING↗

ARCADE (Advanced Reactor Cyber Analysis and Development Environment)

SAND2025-11780O ARCADE (Advanced Reactor Cyber Analysis and Development Environment) software performs cybersecurity experiments on Defensive Cyber Security Architectures (DCSA) for Distributed Control Systems (DCSs). The application is integrated into a cohesive environment that performs cyber risk analyses and reduces costs. ARCADE can investigate the entire cyber-attack surface of a DCS from the physics of control, down to the firmware of individual components with automated efficiency. ARCADE has five major functional components: the Data Broker system, the virtualization environment, the cyber-attack simulator, the cyber-physical analysis system, and the physics simulator. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology & Engineering Solutions of Sandia, LLC, a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy’s National Nuclear Security Administration under contract DE-NA0003525.

Valme, Romuald↗

FY07 LDRD Final Report Precision, Split Beam, Chirped-Pulse, Seed Laser Technology

The goal of this LDRD ER was to develop a robust and reliable technology to seed high-energy laser systems with chirped pulses that can be amplified to kilo-Joule energies and recompressed to sub-picosecond pulse widths creating extremely high peak powers suitable for petawatt class physics experiments. This LDRD project focused on the development of optical fiber laser technologies compatible with the current long pulse National Ignition Facility (NIF) seed laser. New technologies developed under this project include, high stability mode-locked fiber lasers, fiber based techniques for reduction of compressed pulse pedestals and prepulses, new compact stretchers based on chirped fiber Bragg gratings (CFBGs), new techniques for manipulation of chirped pulses prior to amplification and new high-energy fiber amplifiers. This project was highly successful and met virtually all of its goals. The National Ignition Campaign has found the results of this work to be very helpful. The LDRD developed system is being employed in experiments to engineer the Advanced Radiographic Capability (ARC) front end and the fully engineered version of the ARC Front End will employ much of the technology and techniques developed here.

42 ENGINEERING↗

AVESTAR Center for clean energy plant operators of the future

Clean energy plants in the modern grid era will increasingly exploit carbon capture, utilization, and storage (CCUS), fuel/product flexibility, and load following. Integrated power/process plants will require next generation of well-trained engineering and operations professionals. High-fidelity dynamic simulators are well suited for training, education, and R&D on clean energy plant operations. Combining Operator Training System (OTS) with 3D virtual Immersive Training System (ITS) enables simultaneous training of control room and plant field operators of the future. Strong collaboration between industry, academia, and government is required to address advanced R&D challenges. AVESTAR Center brings together simulation technology and world-class expertise focused on accelerating development of clean energy plants and operators of the future.

97 MATHEMATICS AND COMPUTING↗

Advancing Manufacturing Research Through Competitions

Competitions provide a technique for building interest and collaboration in targeted research areas. This paper will present a new competition that aims to increase collaboration amongst Universities, automation end-users, and automation manufacturers through a virtual competition. The virtual nature of the competition allows for reduced infrastructure requirements while maintaining realism in both the robotic equipment deployed and the scenarios. Details of the virtual environment as well as the competitions objectives, rules, and scoring metrics will be presented.

42 ENGINEERING↗

Nuclear history, politics, and futures from (A)toms-to(Z)oom: Design and deployment of a remote-learning special-topics course for nuclear engineering education

To address the lack of familiarity with nuclear history common among nuclear engineers and physicists, we outline the design and deployment of a special-topics course entitled “NE290: Nuclear History, Politics, and Futures” throughout which we contextualize the importance of the field at its inception, in current affairs, and in future endeavors. We argue that understanding this history is paramount in internalizing a sense of respect for the scientific, technical, and sociological ramifications of an unlocked atom—as well as its perils. We begin by outlining the gaps in secondary educational offerings for nuclear history and their importance in consideration with nontechnical engineering guidelines. We then outline a number of ABET specifications as pedagogical goals for NE290 from which we derive a list of target student learning objectives. Next, we outline the NE290 syllabus in terms of assignments and an overview of course content in the form of a class timeline. We provide an extensive description of the materials and teaching methodologies for the four units of NE290: Twentieth-Century Physics, Physics in WWII, the Early Cold War, and the Late Cold War and Modern Era. We detail the sequence of lectures across the course and historical timelines leading up to a showcasing of NE290 final projects which mirror in creativity the novelty of course offering. Because NE290 was first offered during Spring 2021 during the COVID-19 pandemic, additional measures in the form of new tools were used to augment the mandate of remote learning. In particular, we leveraged the newfound ubiquity of videoconferencing technology to recruit geographically diverse guest lecturers and used the MIRO tool for virtual whiteboarding. Lastly, we provide an accounting of course outcomes drawn from student feedback which—in tandem with the complete distribution of course material—facilitates the integration of nuclear history into the curriculum for the wider nuclear engineering and physics communities.

Berliner, Aaron J.↗

Model building techniques for analysis.

The practice of mechanical engineering for product development has evolved into a complex activity that requires a team of specialists for success. Sandia National Laboratories (SNL) has product engineers, mechanical designers, design engineers, manufacturing engineers, mechanical analysts and experimentalists, qualification engineers, and others that contribute through product realization teams to develop new mechanical hardware. The goal of SNL's Design Group is to change product development by enabling design teams to collaborate within a virtual model-based environment whereby analysis is used to guide design decisions. Computer-aided design (CAD) models using PTC's Pro/ENGINEER software tools are heavily relied upon in the product definition stage of parts and assemblies at SNL. The three-dimensional CAD solid model acts as the design solid model that is filled with all of the detailed design definition needed to manufacture the parts. Analysis is an important part of the product development process. The CAD design solid model (DSM) is the foundation for the creation of the analysis solid model (ASM). Creating an ASM from the DSM currently is a time-consuming effort; the turnaround time for results of a design needs to be decreased to have an impact on the overall product development. This effort can be decreased immensely through simple Pro/ENGINEER modeling techniques that summarize to the method features are created in a part model. This document contains recommended modeling techniques that increase the efficiency of the creation of the ASM from the DSM.

99 GENERAL AND MISCELLANEOUS↗

The Integrated Virtual Blast Furnace: Enabling Physics-Based Operational Guidance

As part of a DOE-supported research effort, Purdue University Northwest researchers are collaborating with Oak Ridge National Laboratory and United States Steel Corporation to develop a tool to provide blast furnace operators and engineers with process performance insight comparable to high-fidelity computational fluid dynamics modeling, accelerated to provide “what-if” scenarios at near-real-time speed. This is accomplished by pre-simulating a baseline case and a range of potential operating scenarios to establish how the furnace responds to changing inputs, then training a neural network-based Reduced Order Model to accelerate the speed at which predictions of key parameters can be generated.

Okosun, Tyamo↗

Three-dimensional grain mapping of open-cell metallic foam by integrating synthetic data with experimental data from high-energy X-ray diffraction microscopy

Highlights: • High-energy X-ray measurements are made for ligaments of an open-cell aluminum foam. • Grain centroids and orientations are measured using high-energy X-ray diffraction. • 3D grain map is virtually reconstructed by integrating measured and synthetic data. - Abstract: The complex mechanical response of open-cell foams depends strongly on the hierarchy of length scales inherent in them, from engineering-part scale to the ligament scale through the grain scale down to the crystal-lattice scale. A first step toward understanding and predicting the coordinated mechanical response across length scales requires characterizing the open-cell foam structure in three dimensions at relevant scales. Here, we present an initial attempt to digitally represent a physically-realized aluminum alloy foam in terms of both its geometry/topology as well as its underlying crystallographic orientations by integrating several advanced techniques. Specifically, we use a combination of X-ray computed tomography and X-ray diffraction microscopy in conjunction with synthetic grain mapping. Experimental investigation of the foam shows relatively large grain sizes with respect to the ligament length scale, implying that competing mechanics at different length scales (i.e. grain scale vs. ligament scale) will need to be fully incorporated to understand the mechanical behavior of the foam. The integration of non-destructive measurement techniques with synthetic-data generation provides a path toward realistic modeling of bulk samples of open-cell metal foam resolved at the scale of individual grains.

36 MATERIALS SCIENCE↗