Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “tidal modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Wave Energy Converter Power Take-Off Modeling and Validation From Experimental Bench Tests

This article describes the implementation of a new numerical model of the power take-off system installed in the Monterey Bay Aquarium Research Institute wave energy converter, a device developed to provide power to various oceanic research missions. The simultaneous presence of hydraulic, pneumatic, and electrical subsystems in the power take-off system represents a significant challenge in forging an accurate model able to replicate the main dynamic characteristics of the system. The validation of the new numerical model is addressed by comparing simulations with the measurements obtained during a series of bench tests. Data from the bench tests show good agreement with the numerical model. The validated model provides deeper insights into the complex nonlinear dynamics of the power take-off system and will support further performance improvements in the future.

16 TIDAL AND WAVE POWER↗
DOE OSTI2023

Turbine-based Power System Tool

Advanced research tools are essential to illustrate the effects of turbine-based power system operations on the electric grid network. This paper presents the development of an open-source tool to visualize the operation of turbine-based electricity generation. The tool exposes power system models, control parameters, and corresponding values of the turbine model and its electrical system, allowing them to customize the simulation according to their needs. The developed tool enables users to simulate power profiles for different turbinebased energy generation such as wind, tidal, and gas turbines. It allows users to investigate the details of the generated profiles of various types of turbine systems at various scales. It can provide valuable insights into model development and facilitate the analysis of integrated power systems. By enabling access to turbine-based operations visualization, the tool aims to bridge the gap between advanced research tools and users, facilitating broader adoption of renewable energy technologies and aiding in developing sustainable power systems.

Kini, Roshan L.↗
DOE OSTI2021

AT2017gfo: Bayesian inference and model selection of multicomponent kilonovae and constraints on the neutron star equation of state

The joint detection of the gravitational wave GW170817, of the short γ-ray burst GRB170817A and of the kilonova AT2017gfo, generated by the the binary neutron star (NS) merger observed on 2017 August 17, is a milestone in multimessenger astronomy and provides new constraints on the NS equation of state. We perform Bayesian inference and model selection on AT2017gfo using semi-analytical, multicomponents models that also account for non-spherical ejecta. Observational data favour anisotropic geometries to spherically symmetric profiles, with a log-Bayes’ factor of ~104, and favour multicomponent models against single-component ones. The best-fitting model is an anisotropic three-component composed of dynamical ejecta plus neutrino and viscous winds. Using the dynamical ejecta parameters inferred from the best-fitting model and numerical–relativity relations connecting the ejecta properties to the binary properties, we constrain the binary mass ratio to q < 1.54 and the reduced tidal parameter to $120\lt \tilde{\Lambda }\lt 1110$. Finally, we combine the predictions from AT2017gfo with those from GW170817, constraining the radius of a NS of 1.4 M ⊙ to 12.2 ± 0.5 km (1σ level). This prediction could be further strengthened by improving kilonova models with numerical-relativity information.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Recent Developments in the WEC-Sim Open-Source Design Tool: Preprint

WEC-Sim (Wave Energy Converter SIMulator) is an open-source code for simulating wave energy converters, which has been actively developed and applied to simulate a wide variety of device archetypes and has become a popular tool since its initial release in 2014. WEC-Sim is developed jointly by the National Renewable Energy Laboratory (NREL) and Sandia National Laboratories (SNL) within the MATLAB/SIMULINK environment. Figure 1 illustrates a general wave-to-wire model which begins with a deployment site resource characterization, which is used to complete the hydrodynamic simulation of a single WEC (or array), with the power generation profile imported to a grid simulator to understand the influence on the local electrical network. While modelling the entire wave-to-wire is difficult and encompass multiple time scales and physics, WEC-Sim is focused on the hydrodynamics simulation to predict, analyze and optimize WEC dynamics and power performance. WEC-Sim simulations are performed in the time domain based on the radiation and diffraction method using hydrodynamics coefficients derived from boundary element method (BEM) based-frequency-domain potential flow solvers (e.g., WAMIT, NEMOH, Capytaine, or ANSYS-AQWA). Within this level of modeling fidelity, WEC-Sim can handle floating body hydrodynamics, mechanical and electrical power generation methods, advanced control implementation, mooring systems, and other unique applications such as desalination. Table 1 lists additional WEC-Sim functionalities, which are created using prebuilt Simulink blocks and MATLAB scripts that can simulate a wide range of floating systems and the corresponding auxiliary subsystems.

hydrodynamics modeling↗
DOE OSTI2023

Investigating Marine Environmental Degradation of Additive Manufacturing Materials for Renewable Energy Applications

Marine renewable energy is a relatively young industry where there is a great need for rapid prototyping in design-build-test campaigns to quickly mature groundbreaking technologies. Additive manufacturing has an important role to play in the industry; however, little information is available to marine energy developers to help inform them on which additive manufacturing materials are appropriate for highly loaded structures in harsh marine environments. This paper presents an initial study on the mechanical characterization of polymeric additive manufacturing materials and the degradation effects due to the marine environment. Ultem 9085, acrylonitrile styrene acrylate, and chopped carbon-filled nylon, as well as continuous carbon and glass fiber-reinforced nylon were chosen for this study. Samples were manufactured to perform a variety of tension, shear, and compression mechanical characterization tests on the materials. Half of the samples were conditioned in Pacific Ocean water for approximately 6 months at the Pacific Northwest National Laboratory's Marine and Coastal Research Laboratory before being returned for mechanical characterization. The mechanical testing results showed that the Ultem 9085 and acrylonitrile styrene acrylate materials experienced little to no degradation in stiffness or strength after exposure to the marine environment. On the other hand, the nylon-based materials suffered significant stiffness and strength degradation (over 50% in some cases) after environmental conditioning. Ultimately, these data sets should serve as starting points to allow marine renewable energy developers to make informed additive manufacturing material choices for their prototype deployments.

additive manufacturing↗
DOE OSTI2024

Advanced Features and Recent Developments in the WEC-Sim Open-Source Design Tool: Preprint

WEC-Sim is an open-source tool developed in Matlab/Simulink to simulate wave energy converters. WEC-Sim has been developed jointly by the National Renewable Energy Laboratory (NREL) and Sandia National Laboratories (SNL) since its initial release in 2014. WEC-Sim simulations are performed in the time domain based on the radiation and diffraction method using hydrodynamics coefficients derived from boundary element method (BEM)-based frequency-domain potential flow solvers (e.g., WAMIT, NEMOH, Capytaine, or ANSYS-AQWA). Within this level of modeling fidelity, WEC-Sim can handle floating body hydrodynamics, mechanical and electrical power generation methods, advanced control implementation, mooring systems, and other unique applications such as desalination. WEC-Sim functionalities are developed using Simulink blocks and Matlab functions. WEC-Sim is capabilities include simulation of different wave conditions, constraints and PTOs, body dynamics, mooring systems, among other advanced features such as nonlinear hydrodynamics, nonlinear PTOs, body-to-body interactions, etc.

hydrodynamics modeling↗
DOE OSTI2020

Verdant Power TriFrame, Gen5 KHPS Turbine, and BOP System Content Models

This submission includes System Content Models with data following manufacture for the Verdant Power TriFrame, Gen5 Kinetic Hydropower System (KHPS) Turbines, and Balance of Plant (BOP). The TriFrame installs 3 Gen5 KHPS Turbines. The BOP system controls the turbines and interconnects the TriFrame to shoreline with supervisory control and data acquisition (SCADA).

16 TIDAL AND WAVE POWER↗
DOE OSTI2022

Design, dynamic modeling and wave basin verification of a Hybrid Wave–Current Energy Converter

Massive and high-density Marine and Hydrokinetic (MHK) energy is contained in the ocean, including waves, tidal streams, and ocean currents. Traditional MHK energy converters harvest energy from only a single MHK energy source, which does not fully exploit the energy potential that co-exists in multiple forms of MHK energy in the ocean. This paper presents the design and dynamics of a Hybrid Wave–Current Energy Converter (HWCEC) that can simultaneously convert both wave and current energy to electricity with a single Power Take-off (PTO) through the engagement and disengagement of the three one-way clutches. The critical design parameters are analyzed through modeling and simulation, including the transmission ratios, the electrical impedance, and the turbine-heave plate distance. Water basin tests in a wave–current tank were conducted, which shows the prototyped HWCEC can improve the electric power output by 38%–71% for regular waves and 79% for irregular waves, while providing a 70% reduction of the Peak to Average Ratio (PAR) of power compared to the baseline Wave Energy Converter (WEC). Here we further analyze the occurring percentages of the instant power of both WEC and HWCEC in irregular wave tests, shedding new insight on how HWCEC reduces the PAR.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

A Multi-variable, Multi-value Hydrodynamic Modeling Approach to Support Marine Energy and Coastal Resilience Applications

Funded by the Marine Energy Seedling Laboratory Program, the study reported on here aimed to develop a multi-variable, multi-value hydrodynamic modeling approach based on the Finite-Volume Community Ocean Model (FVCOM) to support a wide range of marine renewable energy and coastal resilience applications. We migrated the marine hydrokinetic energy module to simulate tidal energy extraction by tidal turbines under wave-current interactions. We explored the particle tracking module in FVCOM and applied it to Sequim Bay, Washington, to illustrate the surface current field and mimic the pollutant transport near the surface. A tracer-water age module was added to FVCOM to examine water exchange through the entrance. Lastly, a user-specified vertical coordinate option was added to FVCOM to improve simulation of the effect of floating turbines on surface currents and scalar transport. The above-described model development has been tested using a simplified model domain and demonstrated in real-world coastal systems. The outcome of this project will provide a useful modeling code and approach for marine renewable energy and coastal resilience research and applications.

16 TIDAL AND WAVE POWER↗
DOE OSTI2026

Implementation of a Three-Dimensional Planetary Boundary Layer Parameterization in a Coupled Modeling System and Evaluation of "Gray Zone" Simulations of a Wind-Wave Event Off the US California Coast Using Observations

A three-dimensional (3D) planetary boundary layer (PBL) parameterization was added to the Coupled Ocean Atmosphere Wave Sediment Transport (COAWST) model and the first coupled atmosphere/wave "gray zone" simulations were carried out using the 3D PBL parameterization. A case study of a significant wind-wave event from 4-8 November 2020 off the US west coast was examined, with a focus on the impacts of the event within an approximate 280x280 km central California coastal region covering the Bureau of Ocean Energy Management Morro Bay wind energy lease area. Simulations with both one-dimensional (1D; Yonsei University) and 3D PBL parameterizations were examined in this nest with ..delta..x=400 m. Two-way coupling was active, with near-surface winds feeding back to the wave model and bulk wave statistics feeding back to the atmospheric model. Both simulations compared favorably with buoy observations in capturing the timing and magnitude of wind speed, temperature, dewpoint, and significant wave height, as the front associated with the maritime weather system moved southward across coastal California. However, wind speed errors over land were larger. Time series of the vertical profile of winds below z=250 m from the simulations compared favorably with observations from the US Dept. of Energy Morro Bay Doppler lidar buoy. Differences between the coupled 1D and 3D PBL simulations were minor. The most notable difference was that the simulation using the 3D PBL parameterization had approximately 10 % weaker winds at the peak of the event causing 10 % lower significant wave heights. This difference was shown to be mostly due to differences in the vertical mixing treatment between the parameterizations, in particular the nonlocal downward mixing of higher momentum air in the 1D Yonsei University parameterization in convective conditions. Overall, this work demonstrates that the 3D PBL parameterization can be used in a coupled atmosphere/wave modeling framework with similar behaviors as traditional PBL parameterizations that do not provide horizontal turbulent variances and fluxes.

16 TIDAL AND WAVE POWER↗
DOE OSTI2021

NREL Data, Modeling, and Tools Empower Marine Energy Analysis

NREL performs R&D and economic analyses to drive and empower the development of wave energy and tidal, ocean, and river current energy technologies. These technologies deliver renewable electricity to the grid and provide energy solutions that support the evolving "blue economy."

HYDRO ENERGY↗
DOE OSTI2024

TEAMER: Numerical Modeling and Optimization of the iProTech Pitching Inertial Pump (PIP) Wave Energy Converter (WEC)

This project focused on developing an automated workflow to evaluate and optimize the iProTech Pitching Inertial Pump (PIP) wave energy converter (WEC) using open-source Python packages and the MATLAB/Simulink tool, WEC-Sim. The process involved parameterizing key design variables, running time-domain simulations, and performing sensitivity analyses to determine their impact on power output. The workflow, designed for the PIP device, is generalized and can be extended to optimize other WECs that can be simulated in WEC-Sim. This work establishes a foundation for future time-domain-based WEC design optimizations. Included in this submission are all figures from the final report and the model inputs required to generate them. This includes Python scripts with inputs that produce the meshes, boundary element method (BEM) models, hydrodynamic coefficients, and the WEC-Sim models used for time-domain analyses. Although data for every single run is not included to save space, all of it can be reproduced using the provided models. Detailed instructions for setting up the environment and running the codes are also included.

16 TIDAL AND WAVE POWER↗
DOE OSTI2026

Evidence for Environmental Stripping in the Coma Cluster

The stability and longevity of globular clusters (GCs) make them effective tracers of the dynamical histories of galaxies in cluster environments. We construct a catalog of 23,351 GC candidates in the Coma Cluster using imaging from the Hubble Space Telescope Advanced Camera for Surveys. We cross-match galaxy data from the SIMBAD, NASA/IPAC Extragalactic Database, and Sloan Digital Sky Survey archives to construct a galaxy sample and model their GC populations using the GC specific frequency. We find several galaxies with significantly smaller GC populations than expected from their luminosities, consistent with either tidal stripping or intrinsically low formation efficiencies. We analyze annular and Voronoi GC radial profiles of the two brightest cluster galaxies (BCGs), NGC 4874 and NGC 4889, as well as other Coma galaxies. A two-dimensional Voronoi density mapping reveals GC populations with marked deficits compared to our modeled expectations, including galaxies in proximity to the BCGs (e.g., IC 3998, NGC 4875, and NGC 4876) and others distributed across Coma (e.g., NGC 4908, NGC 4883, and IC 4042). Azimuthal symmetry testing suggests past dynamical interactions may have truncated GC systems in some galaxies, while intrinsic deficits are probable in others (e.g., IC 3973, IC 3976, IC 4040, and IC 4045). Our results show that GC deficits exist in several Coma galaxies and that the two-dimensional density structure reveals environmental signatures, with asymmetry statistics consistent with directional stripping. These findings highlight GC populations as powerful probes of environmental processing and the dynamical histories of galaxies in dense cluster environments.

Pomeroy, Richard T. [University of Texas Rio Grand↗
DOE OSTI2025

Benchmark study of the DTU OWC chamber with both two-way and one-way absorption

This paper reports on a benchmark study based on small-scale (1:50) measurements of a single, oscillating water column chamber mounted sideways in a long flume. The geometry of the OWC chamber is extracted from a barge-like, attenuator-type floating concept “KNSwing” with 40 chambers targeted for deployment in the Danish part of the North Sea. In addition to traditional two-way energy extraction we also consider one-way energy extraction with passive venting and compare chamber response, pressures and total absorbed energy between the two methods. A blind study was established for the numerical modeling, with participants applying several implementations of weakly nonlinear potential flow theory and commercial Navier–Stokes solvers (CFD). Both compressible and incompressible models were used for the air phase. Potential flow calculations predict more energy absorption near the chamber resonance for one-way absorption than for two-way absorption, but the opposite is found from the experimental measurements. This outcome is mainly attributed to energy losses in the experimental passive valve system, but this conclusion must be confirmed by better experimental measurements. Modeling the one-way valve in CFD proved to be very challenging and only one team was able to provide results which were generally closer to the experiments. The study illustrates the challenges associated with both numerical and experimental analysis of OWC chambers. Air compressibility effects were not found to be important at this scale, even with the large volume of additional air used for the one-way case.

16 TIDAL AND WAVE POWER↗
DOE OSTI2025

From TPL assessment to design optimization: Wave energy converter control co-design applied to the RM3

The Reference Model (RM) project developed six marine energy converter concepts using a sequential design methodology, which, while widely adopted in the industry, often overlooks interactions between system components, resulting in suboptimal designs. One such example is the Reference Model 3 (RM3), a two-body point absorber wave energy converter (WEC). An assessment using the Technology Performance Level (TPL) revealed that RM3’s low power-to-cost ratio, partly due to expensive steel construction, limits its techno-economic performance. Here, this study aims to redesign RM3 by reducing its scale and employing control co-design to integrate WEC and Power Take-Off (PTO) dynamics, constraints, and cost considerations within an optimization framework. We demonstrate the limitations of RM3’s current PTO design and explore the benefits of scaling down to enhance techno-economic viability by lowering material costs. Using WecOptTool, we conduct a parameter sweep over gear ratios and spring stiffnesses for various Commercial Off-The-Shelf generators in irregular wave conditions. Our findings emphasize the importance of aligning PTO components with WEC dynamics, showing that control co-design and strategic scaling can improve RM3’s power-to-cost ratio. This study presents a transferable example of applied control co-design for other WECs, supporting early-stage developers in their design decisions.

Off the shelf components↗
DOE OSTI2021

The Radius of PSR J0740+6620 from NICER and XMM-Newton Data

PSR J0740+6620 has a gravitational mass of 2.08 ± 0.07 M ⊙ , which is the highest reliably determined mass of any neutron star. As a result, a measurement of its radius will provide unique insight into the properties of neutron star core matter at high densities. Here we report a radius measurement based on fits of rotating hot spot patterns to Neutron Star Interior Composition Explorer (NICER) and X-ray Multi-Mirror (XMM-Newton) X-ray observations. We find that the equatorial circumferential radius of PSR J0740+6620 is 13.7$^{+2.6}_{–1.5}$ km (68%). We apply our measurement, combined with the previous NICER mass and radius measurement of PSR J0030+0451, the masses of two other ~2 M ⊙ pulsars, and the tidal deformability constraints from two gravitational wave events, to three different frameworks for equation-of-state modeling, and find consistent results at ~1.5-5 times nuclear saturation density. For a given framework, when all measurements are included, the radius of a 1.4 M ⊙ neutron star is known to ±4% (68% credibility) and the radius of a 2.08 M ⊙ neutron star is known to ±5%. The full radius range that spans the ±1σ credible intervals of all the radius estimates in the three frameworks is 12.45 ± 0.65 km for a 1.4 M ⊙ neutron star and 12.35 ± 0.75 km for a 2.08 M ⊙ neutron star.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

Physics-constrained Gaussian process model for prediction of hydrodynamic interactions between wave energy converters in an array

To improve the efficiency of wave farms and achieve maximum power generation, the layout of wave energy converters (WECs) in an array needs to be carefully designed so that the hydrodynamic interactions can be positively exploited. For this, the hydrodynamic characteristics of the WEC array in different layouts need to be calculated. However, such calculations using numerical models usually entail significant computational cost, especially for large arrays of WECs. To address the computational challenge, a physics-constrained Gaussian process (GP) model is proposed to replace the original expensive numerical model and predict the hydrodynamic characteristics of the WECs for any array layout. By exploring the relationship between the WEC array (i.e., the input) and different hydrodynamic characteristics (i.e., the output), here we summarize a set of physical constraints/features, including invariance, symmetry, and additivity. This prior knowledge about the input-output relationship is then directly embedded in the constructed GP model through the design of physics-constrained kernels. In particular, a double-sum invariant kernel is first developed to incorporate the invariance and symmetry features, and then an additive kernel is developed to incorporate the additive feature of the problem. The invariant kernel and the additive kernel are then integrated to construct the physics-constrained GP model. Compared to the standard GP model, the proposed physics-constrained GP models require less training data to achieve the desired accuracy in predicting the hydrodynamic characteristics and are also less vulnerable to the curse of dimensionality (i.e., good scalability for large arrays) due to the use of an additive kernel. The efficiency, accuracy, and scalability of the proposed approach are demonstrated through an application to predict the hydrodynamic characteristics for WEC arrays of different sizes and layouts.

16 TIDAL AND WAVE POWER↗
DOE OSTI2025

Modelling the Effects of Wetland Restoration on Coastal Hydrology: A Case Study of Elkhorn Slough Watershed, California

ABSTRACT Coastal wetlands, some of the most productive ecosystems on Earth, provide critical ecosystem services, including support of biodiversity, carbon sequestration and flood protection. In recent decades, these ecosystems have experienced extensive coastal wetland loss. Coastal wetland restoration provides a beacon of hope, offering a chance to reclaim these important habitats. However, even with billions of dollars invested worldwide in restoring coastal wetlands, we still lack comprehensive knowledge about the effectiveness of these restoration efforts in recovering wetland ecosystem functions and how future climate change may affect these efforts. The ability to evaluate how these ecosystems will function in the future is vital for examining current investments and developing future protection and management plans. We selected Elkhorn Slough, a tidal estuary, in California, to investigate the impact of wetland restoration and sea level rise (SLR) on coastal hydrology using the process‐based coastal hydrologic model, Advanced Terrestrial Simulator (ATS), informed by site‐specific data. We designed a novel modelling workflow for incorporating wetland restoration features into land cover and soil properties for the model parameterization. The validation results demonstrate a strong agreement between modelled and observed data. We studied the characteristics of coastal watershed hydrology, then focused on the surface water dynamics at two wetland sites within Elkhorn Slough, a reference site and a restored site. Our simulation results indicate that the restored site successfully maintains surface elevation, resulting in reduced surface inundation. We also examined the impact of wetland restoration under expected SLR over the next few decades. The low‐lying Yampah Marsh, the reference site, is likely to be inundated due to future SLR when highest tides arrive, while a higher percentage of Hester Marsh, the restored site, would retain marsh vegetation in coming decades, regardless of tidal conditions. Our study provides important information for examining the outcome of restoration practices that include surface elevation in tidal wetlands under climate changes.

advanced terrestrial simulator↗