Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “static area”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Structural design considerations for the beam transmission optical system

The paper describes the JPL study leading to a baseline design of the Beam Transmission Optical System (BTOS), designed for the delivery of laser energy from earth to space targets. The study identified the driving environmental and functional requirements; developed a conceptual design of the BTOS telescope; and performed static, thermal distortion, and model analyses to verify that these requirements are met. The study also identified major areas of concern which should be investigated further.

Macneal, Paul D.↗
NASA NTRS1993

Sensitivity analysis of discrete systems

A selection is presented of methods used in the calculation of sensitivity derivatives of behavior and response of discretely modeled structure. Attention is given to methods for the selection of finite-difference step sizes for structural constraint derivatives, and techniques for finite difference derivatives in iteratively-solved problems. Also noted are methods for sensitivity of linear static response, and methods for second derivatives of structural response, derivatives of stresses, and nonlinear response; an emerging area of interest concerns the derivatives of transient response.

Adelman, Howard M.↗
NASA NTRS1955

Investigation in the Langley Free-Flight Tunnel of the Low-Speed Stability and Control Characteristics of a 1/10-Scale Model Simulating the Convair F-102A Airplane

An investigation of the low-speed, power-off stability and control characteristics of a 1/10-scale model simulating the Convair F-102A airplane has been made in the Langley free-flight tunnel. The model in its basic configuration and with two modifications involving leading- edge slats and an increase in vertical-tail size was flown through a lift-coefficient range from 0.7 to the stall. Only relatively low-altitude conditions were simulated. The longitudinal stability characteristics of the model were considered satisfactory for all conditions investigated. The lateral stability characteristics were considered satisfactory for the basic configuration over the lift-coefficient range investigated, except near the stall, where large values of static directional instability caused the model to be directionally divergent. An 80-percent increase in vertical-tail area increased the angle of attack at which the model became directionally divergent. The longitudinal and lateral control characteristics were generally satisfactory. Although the adverse sideslip characteristics for the model were considered acceptable over the angle-of-attack range, analysis indicates that the adverse sideslip characteristics of the airplane may be objectionable at high angles of attack.

Boisseau, Peter C.↗
NASA NTRSDate not supplied

Error Localization Examples: Looking for a Needle in a Hay-stack

Finite element models (FEM) are routinely developed and used during fabrication of high dollar-value hardware. NASA as part of the pre-flight certification of launch vehicles routinely conducts vibration and static tests to calibrate models used for flight-risk assessments. As part of the calibration process, certain areas in the model are modified, using engineering judgment and sensitivity analysis, to match the test results. Unfortunately, tools to identify problem areas in the FEM using test data directly are scarce. Over the years, Error Localization Algorithms (ELA) have been proposed with very limited success. Recently, the Analytical Dynamics Model Improvement (ADMI) algorithm, which computes closed-form mass and stiffness corrections to match the test data exactly, have been shown to be effective for error localization. The paper will present several FEM example problems where ELA is used with simulated test data to determine FEM problem areas. For each example, the correct answer is shown along with ELA results. It is shown that the ELA process is able to identify general problem areas in the FEM, which are consistent with known model perturbations. However, in most cases the ELA identified area of improvement is larger than the true answer. Nonetheless, with proper optimization tools, calibration results using the ELA identified areas provide excellent results.

error localization↗
NASA NTRS1984

Hot-flow tests of a series of 10-percent-scale turbofan forced mixing nozzles

An approximately 1/10-scale model of a mixed-flow exhaust system was tested in a static facility with fully simulated hot-flow cruise and takeoff conditions. Nine mixer geometries with 12 to 24 lobes were tested. The areas of the core and fan stream were held constant to maintain a bypass ratio of approximately 5. The research results presented in this report were obtained as part of a program directed toward developing an improved mixer design methodology by using a combined analytical and experimental approach. The effects of lobe spacing, lobe penetration, lobe-to-centerbody gap, lobe contour, and scalloping of the radial side walls were investigated. Test measurements included total pressure and temperature surveys, flow angularity surveys, and wall and centerbody surface static pressure measurements. Contour plots at various stations in the mixing region are presented to show the mixing effectiveness for the various lobe geometries.

Head, V. L.↗
NASA NTRS1980

VCE early acoustic test results of General Electric's high-radius ratio coannular plug nozzle

Results of variable cycle engine (VCE) early acoustic engine and model scale tests are presented. A summary of an extensive series of far field acoustic, advanced acoustic, and exhaust plume velocity measurements with a laser velocimeter of inverted velocity and temperature profile, high radius ratio coannular plug nozzles on a YJ101 VCE static engine test vehicle are reviewed. Select model scale simulated flight acoustic measurements for an unsuppressed and a mechanical suppressed coannular plug nozzle are also discussed. The engine acoustic nozzle tests verify previous model scale noise reduction measurements. The engine measurements show 4 to 6 PNdB aft quadrant jet noise reduction and up to 7 PNdB forward quadrant shock noise reduction relative to a fully mixed conical nozzle at the same specific thrust and mixed pressure ratio. The influences of outer nozzle radius ratio, inner stream velocity ratio, and area ratio are discussed. Also, laser velocimeter measurements of mean velocity and turbulent velocity of the YJ101 engine are illustrated. Select model scale static and simulated flight acoustic measurements are shown which corroborate that coannular suppression is maintained in forward speed.

Knott, P. R.↗
NASA NTRS1951

Dynamics of a turbojet engine considered as a quasi-static system

A determination of the dynamic characteristics of a typical turbojet engine with a centrifugal compressor, a sonic-flow turbine-nozzle diaphragm, and fixed area exhaust nozzle is presented. A generalized equation for transient behavior of the engine was developed; this equation was then verified by calculations using compressor and turbine performance charts extrapolated from equilibrium operating data and by experimental data obtained from an engine operated under transients in fuel flow. The results indicate that a linear differential equation for engine acceleration as a function of fuel flow and engine speed for operation near a steady-state operating condition can be written. The coefficients of this equation can be obtained either from actual transient data or, with a fair degree of accuracy, from the steady-state performance maps of the compressor and turbine, and can be corrected for altitude in the same manner that steady-state performance data are corrected.

Otto, Edward W↗
NASA NTRS1994

Static stability of a three-dimensional space truss

Space station requirements for power have resulted in a need for photovoltaic solar arrays possessing large blanket surface area. However, due to the limited shuttle payload volume solar array designers have been driven to a deployable concept that by nature is extremely flexible. The principal support for this array system is the Folding Articulating Square Truss Mast (FASTMast). In order to accomodate service loads the FASTMast is expected to exhibit nonlinear behavior which could possibly result in structural instability. Presented herein are the results of the Lewis Research Center test and analysis efforts performed in an effort to characterize the FASTMast structural behavior in terms of stability. Results include those obtained from recent nonlinear testing and analysis involving a 1/10 segment of the FASTMast flight article. Implications of these results as they relate to expected behavior of the flight unit will also be discussed.

Shaker, John F.↗
NASA NTRS1994

Static Stability of a Three-Dimensional Space Truss

Space Station requirements for power have resulted in a need for photovoltaic solar arrays possessing large blanket surface area. However, due to the limited Shuttle payload volume solar array designers have been driven to a deployable concept that by nature is extremely flexible. The principal support for this array system is the Folding Articulating Square Truss Mast (FASTMast). In order to accommodate service loads the FASTMast is expected to exhibit nonlinear behavior which could possibly result in structural instability. Presented herein are the results of the Lewis Research Center test and analysis efforts performed in an effort to characterize the FASTMast structural behavior in terms of stability. Results include those obtained from recent nonlinear testing and analysis involving a 1/10 segment of the FASTMast flight article. Implications of these results as they relate to expected behavior of the flight unit will also be discussed.

Shaker, John F.↗
NASA NTRS1979

The XFV-12A Thrust-Augmented Wing (TAW) prototype aircraft

The XFV-12A, a unique V/STOL technology prototype aircraft being developed for the Navy, is described. The innovative design features a thrust augmented wing and a canard ejector. Structural, functional, and control test performances are discussed. Static tether test results are also discussed. Assessment of test results are given along with projections for future modification areas.

Murphy, R.↗
NASA NTRS1990

Advanced recovery systems wind tunnel test report

Pioneer Aerospace Corporation (PAC) conducted parafoil wind tunnel testing in the NASA-Ames 80 by 120 test sections of the National Full-Scale Aerodynamic Complex, Moffett Field, CA. The investigation was conducted to determine the aerodynamic characteristics of two scale ram air wings in support of air drop testing and full scale development of Advanced Recovery Systems for the Next Generation Space Transportation System. Two models were tested during this investigation. Both the primary test article, a 1/9 geometric scale model with wing area of 1200 square feet and secondary test article, a 1/36 geometric scale model with wing area of 300 square feet, had an aspect ratio of 3. The test results show that both models were statically stable about a model reference point at angles of attack from 2 to 10 degrees. The maximum lift-drag ratio varied between 2.9 and 2.4 for increasing wing loading.

Geiger, R. H.↗
NASA NTRS2003

On Classification in the Study of Failure, and a Challenge to Classifiers

Classification schemes are abundant in the literature of failure. They serve a number of purposes, some more successfully than others. We examine several classification schemes constructed for various purposes relating to failure and its investigation, and discuss their values and limits. The analysis results in a continuum of uses for classification schemes, that suggests that the value of certain properties of these schemes is dependent on the goals a classification is designed to forward. The contrast in the value of different properties for different uses highlights a particular shortcoming: we argue that while humans are good at developing one kind of scheme: dynamic, flexible classifications used for exploratory purposes, we are not so good at developing another: static, rigid classifications used to trap and organize data for specific analytic goals. Our lack of strong foundation in developing valid instantiations of the latter impedes progress toward a number of investigative goals. This shortcoming and its consequences pose a challenge to researchers in the study of failure: to develop new methods for constructing and validating static classification schemes of demonstrable value in promoting the goals of investigations. We note current productive activity in this area, and outline foundations for more.

Wasson, Kimberly S.↗
NASA NTRS2006

Sealing in Turbomachinery

Clearance control is of paramount importance to turbomachinery designers and is required to meet today's aggressive power output, efficiency, and operational life goals. Excessive clearances lead to losses in cycle efficiency, flow instabilities, and hot gas ingestion into disk cavities. Insufficient clearances limit coolant flows and cause interface rubbing, overheating downstream components and damaging interfaces, thus limiting component life. Designers have put renewed attention on clearance control, as it is often the most cost effective method to enhance system performance. Advanced concepts and proper material selection continue to play important roles in maintaining interface clearances to enable the system to meet design goals. This work presents an overview of turbomachinery sealing to control clearances. Areas covered include: characteristics of gas and steam turbine sealing applications and environments, benefits of sealing, types of standard static and dynamics seals, advanced seal designs, as well as life and limitations issues.

Chupp, Raymond E.↗
NASA NTRS2007

Turbomachinery Clearance Control

Controlling interface clearances is the most cost effective method of enhancing turbomachinery performance. Seals control turbomachinery leakages, coolant flows and contribute to overall system rotordynamic stability. In many instances, sealing interfaces and coatings are sacrificial, like lubricants, giving up their integrity for the benefit of the component. They are subjected to abrasion, erosion, oxidation, incursive rubs, foreign object damage (FOD) and deposits as well as extremes in thermal, mechanical, aerodynamic and impact loadings. Tribological pairing of materials control how well and how long these interfaces will be effective in controlling flow. A variety of seal types and materials are required to satisfy turbomachinery sealing demands. These seals must be properly designed to maintain the interface clearances. In some cases, this will mean machining adjacent surfaces, yet in many other applications, coatings are employed for optimum performance. Many seals are coating composites fabricated on superstructures or substrates that are coated with sacrificial materials which can be refurbished either in situ or by removal, stripping, recoating and replacing until substrate life is exceeded. For blade and knife tip sealing an important class of materials known as abradables permit blade or knife rubbing without significant damage or wear to the rotating element while maintaining an effective sealing interface. Most such tip interfaces are passive, yet some, as for the high-pressure turbine (HPT) case or shroud, are actively controlled. This work presents an overview of turbomachinery sealing. Areas covered include: characteristics of gas and steam turbine sealing applications and environments, benefits of sealing, types of standard static and dynamics seals, advanced seal designs, as well as life and limitations issues.

Chupp, Raymond E.↗
NASA NTRS2010

Utilization of 3-D Imaging Flash Lidar Technology for Autonomous Safe Landing on Planetary Bodies

NASA considers Flash Lidar a critical technology for enabling autonomous safe landing of future large robotic and crewed vehicles on the surface of the Moon and Mars. Flash Lidar can generate 3-Dimensional images of the terrain to identify hazardous features such as craters, rocks, and steep slopes during the final stages of descent and landing. The onboard flight computer can use the 3-D map of terrain to guide the vehicle to a safe site. The capabilities of Flash Lidar technology were evaluated through a series of static tests using a calibrated target and through dynamic tests aboard a helicopter and a fixed wing aircraft. The aircraft flight tests were performed over Moon-like terrain in the California and Nevada deserts. This paper briefly describes the Flash Lidar static and aircraft flight test results. These test results are analyzed against the landing application requirements to identify the areas of technology improvement. The ongoing technology advancement activities are then explained and their goals are described.

Amzajerdian, Farzin↗
NASA NTRS2016

Feasibility of Varying Geo-Fence Around an Unmanned Aircraft Operation Based on Vehicle Performance and Wind

Managing trajectory separation is critical to ensuring accessibility, efficiency, and safety in the unmanned airspace. The notion of geo-fences is an emerging concept, where distance buffers enclose individual trajectories and areas of operation in order to manage the airspace. Currently, the Air Traffic Management system for commercial travel defines static distance buffers around the aircraft; however, commercial UASs are envisioned to operate in significantly closer proximity to other UAS requiring a geo-fence for spacing operations. The geo-fence size can be determined based on vehicle performance characteristics, state of the airspace, weather, and other unforeseen events such as emergency or disaster response. Calculation of the geo-fence size could be determined as part of pre-flight planning and during real-time operations. A largely non-homogeneous fleet of UASs will be operating in low altitude and will likely be commercially developed. Due to intellectual property concerns, the operators may not provide detailed specifications of the control system to UTM. In addition, the huge variety of UAS makes modeling each control system prohibitive and flight data for these vehicles may not exist. Therefore, a generalized, simple geo-fence sizing algorithm must be developed such that it does not rely on detailed knowledge of the vehicle control system, accounts for the presence of urban winds, and is sufficiently accurate. In this work, two simple models are investigated to determine its feasibility as an adequate means for calculating the geo-fence size. The vehicle data used in this work are provided by UAS manufactures who have partnered with NASA's UTM project and some publicly available websites. The first model utilizes wind data processed from the NOAA HRRR (Hourly Rapid Refresh) product and Sonar Annemometer data provided by San Jose State. The second model utilizes OpenFOAM which is a CFD code used to generate a wind field for flow around a single building. The key vehicle performance parameters can include UAS response time to disturbances, command to actuation latency, control system rate limits, time to recovery to desired path, and aerodynamics. It was found that the first model provides an initial understanding of geo-fence sizing, but does not provide enough accuracy to provide UTM with an efficient means of scheduling vehicles. The results of the second model reveal that modeling UAS controls systems with a linearized plant and gain scheduled PID controller does not allow capture the UAS flight dynamics within a significant envelope of the wind disturbances.

uncertainty↗
NASA NTRS1952

Wind-tunnel Investigation of the Contribution of a Vertical Tail to the Directional Stability of a Fighter-type Airplane

Contributions of vertical tail and fuselage to directional stability are determined from pressure distributions measured over wide ranges of angle of attack and angle of yaw with stabilizer in each of three vertical positions, with stabilizer removed and with both stabilizer and vertical tail removed. Results point out inadequacies of current design methods and show that more accurate methods must treat separately contributions of vertical tail, fuselage area above stabilizer, and fuselage area below stabilizer.

LOADS, STEADY - TAIL↗
NASA NTRS1999

Electro-Statically Stricted Polymers (ESSP)

Miniature, lightweight, miser actuators that operate similar to biological muscles can be used to develop robotic devices with unmatched capabilities and impact many technology areas. Electroactive polymers (EAP) offer the potential to producing such actuators and their main attractive feature is their ability to induce relatively large bending or longitudinal strain. EAP actuators can change the paradigm about the complexity of robots, where robotic components such as motors, gears, bearings, and others can be eliminated with simple drive mechanisms. Generally, these materials produce a relatively low force and the applications that can be considered at the current state of the art are relatively limited. While improved material are being developed there is a need for methods to develop longitudinal actuators that can contract similar to muscles. In this study, the authors began investigating the electromechanical behavior of polymers in reaction to a complex configuration of electric fields. A computer model was used to simulate the electromechanical response. Efforts were made to develop both the material basis as well as the electromechanical modeling of the actuator.

Liu, C.↗