Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “seals”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

TEAMER: Biofouling Analysis for Wave Energy Piston Design - Load Cell Data

Biofouling and corrosion are a major concern for all ocean-deployed components, especially when mechanical motion is involved. Triton has developed the concept of a biofouling mitigation seal as part of the piston sealing assembly for the Triton Wave Energy Converter (TSI-WEC). This mitigation seal has the purpose of preventing the formation of a biofilm on the inside of the piston cylinder. It is hypothesized that the prevention of a biofilm will reduce the amount of macro-biofouling that can occur in the piston assembly. The mitigation seal can also reduce the wear on the main dynamic seal, helping to maintain smooth operation and water-tightness. The cylinder is made from a thermoset composite epoxy, which is resistant to corrosion. However, no studies have researched the material's performance with biofouling. Triton placed two prototype Power Take-Off (PTO) assemblies in a PNNL biofouling tank, one with a biofouling mitigation seal and one without, allowing for an evaluation of seal effectiveness at the prevention of biofouling. In actual WEC operation, wave action would react against the piston, which would drive the linear actuator and electric generator, providing electrical power. In the test setup, this was reversed; a linear actuator was powered to drive the piston in a consistent motion within the cylinder. There are two assemblies: one has a biofouling mitigation seal, the other (control) does not. The following data encompasses a 4 month test period, with load cells being used to monitor piston friction force. Results from this testing will be used to improve seal design and material selection, mitigating risk of premature failure during open water testing and evaluation. This project is part of the TEAMER RFTS 3 (request for technical support) program.

16 TIDAL AND WAVE POWER↗
DOE OSTI2022

Leak test for solid oxide fuel cells and solid oxide electrolysis cells

A simple, fast, and economical alcohol penetration method for assessing the solid oxide cell to metal window frame seal in a typical planar design is presented. An alcohol such as ethanol or isopropanol is placed into the cavity of a cell sealed to the window frame. Within 3–5 min, one can determine if the glass seal is hermetic by visual observation along the seal edges on the side of the sealed frame. Cross bubbling and open circuit voltage methods for determining whether the seal failed or cracked at high temperature after final stack firing are also discussed.

25 ENERGY STORAGE↗
DOE OSTI2024

Simulation of Microcapsule Transport in Fractured Media Using Coupled CFD‐DEM

Geothermal energy is sustainable and gaining momentum as a solution to energy crises and environmental issues. However, challenges like production temperature and thermal breakthrough can impact geothermal project efficiency. One innovative solution to alleviate the thermal breakthrough is to inject polymer-based materials that are encapsulated in microcapsules into fractures to modify fracture permeability and prevent preferential flow. In our study, we utilized a coupled computational fluid dynamics and discrete element method to simulate the transport of microcapsules under various scenarios controlled by microcapsule size, microcapsule concentration, and fracture roughness. For a smooth fracture, the results indicate that small microcapsules can travel through a smooth fracture regardless of their concentrations. Large microcapsules can transport through a smooth fracture when present in lower concentrations. However, medium and mixed-size microcapsules tend to cause the sealing of a smooth fracture, irrespective of their concentrations. For a rough fracture, the transport of microcapsules is complicated by their interactions with the rough fracture walls. The presence of two sealing positions in a rough fracture adds further complexity to this transport phenomenon. The size and concentration of microcapsules control one sealing location, while the rough fracture walls determine the other sealing location. The rough walls substantially affect microcapsule transport, rendering the role of microcapsule size and concentration less significant. The simulation results suggest that complex fracture surfaces significantly elevate the occurrence of sealing behavior. To mitigate sealing behavior within more complex fractures, it would be beneficial to use smaller and lower concentrations of microcapsules.

15 GEOTHERMAL ENERGY↗
DOE OSTI2020

An Integrated Multiscale Experimental-Numerical Analysis on Reconsolidation of Salt-Clay Mixture for Disposal of Heat-Generating Waste (Final NEUP Technical Report)

The overall purpose of this research is to improve understanding of THMC coupling effect on the reconsolidation of granular (or crushed) salt-clay mixture used for seal systems of shafts and drifts in salt repositories. This proposed work is partially motivated by the recent work on the Waste Isolation Pilot Plant (WIPP) that shows the promising sealing capability of clay-salt mixture compared to crushed salt. In particular, primary emphasis is to develop a fully integrated multiscale experiment-numerical study to determine and explain what leads to the superior sealing ability of the clay-salt mixture. These research activities are designed to seek further understanding of (1) why clay additives may enhance the fluid trapping and (2) whether this flow barrier effect may prevail under different combinations of temperature, confining pressure, deviatoric stress and other foreseeable environmental factors. If successful, this enhanced flow trapping ability of the seal provides significant improvement to the seal and repository performance and therefore make the repository safer in the long-term. The experiment component includes microstructural investigation and macroscopic tests on a reconsolidated salt-clay mixture. In the microstructural study, the goal is to (1) characterize microscopic distributions of distinct phases (e.g., clay, salt crystal boundaries, trapped brine, and pore) to examine the connectivity of the pore network inside the salt-clay mixture with different amounts of clay additive and moisture content and (2) analyze multiscale imaging data to reconstruct the polycrystalline microstructures for numerical simulations. Meanwhile, macroscopic tests are performed to analyze how clay alters the failure/creep mechanisms in the salt-clay mixture. Microscopic and macroscopic experimental observations will both be used to calibrate and validate a multiscale model that explicitly simulates the capillary and multiphase flow in the connected pores and the deformation due to the presence of intra-crystalline brine at the pore scale via a new polyhedral discrete element–lattice Boltzmann method (DEM-LBM) coupling model. The pore-scale simulations are homogenized via an upscaling procedure that converts pore-scale information (e.g. force exerted on grain boundary, sliding, pressure-solution) to continuum measures (e.g. Cauchy stress, Darcy’s flow) at each integration point in the macroscopic multiphase TMHC model. This multiscale scheme will allow coupling be- tween high-fidelity simulations of brine-salt-clay interaction and the macroscopic TMHC model. The multiscale model helps the understanding of how the trapped brine inclusion affects the pressure-solution mechanism with the presence of clay and moisture. This work brings new insight into the sealing capacity of salt-clay mixture under elevated temperature over a long period of time - a key to evaluating the potential of salt-clay mixture usage for salt repositories.

42 ENGINEERING↗
DOE OSTI2020

PDRD Project 19039 - All metal vacuum scroll pump development for tritium

Currently the United States relies on a single source, foreign company, Eumeca (formerly Normetex) for the supply of an all metal vacuum scroll pump to process tritium. This “one of a kind”, all metal, vacuum scroll pump utilizes no “wetted”, polymeric materials that degrade prematurely when exposed to tritium. U.S. based vacuum scroll pump suppliers typically utilize a polymer, Teflon®, as a tip seal material at the edge of the scroll impellers for proper pump function. Teflon® is known to degrade within a relatively short time frame (approximately 1 year) when continually exposed to tritium gas. This degradation results in “flaking” of the Teflon® material which results in particulate contamination of the process gas stream. While filtration of the particulate is possible, doing so requires additional maintenance which is costly in a glovebox environment. In addition, filtration can degrade pumping system performance as particulate collects in the filter media over time. To date, all of the well established U.S and European based vacuum scroll pump manufacturers have been uninterested in developing an all metal vacuum scroll pump that does not use a polymeric scroll tip seal. This position is taken as the vacuum scroll pump manufacturers do not see a large enough market to make it profitable for them to develop and market an all metal vacuum scroll pump. In the mid 2000s, one company, Air Squared, Inc., a small Original Equipment Manufacturer (OEM) specializing in design and fabrication of custom scroll vacuum pumps and compressors, was willing to pursue the effort. The first design effort incorporated Vespel® as a polymeric tip seal material. Results of this effort led to realizing the affect that the Met-Bel MB-601 metal bellows pump has on performance when used as a backing pump for an all metal vacuum scroll pump without a scroll tip seal. As a result, Air Squared subsequently designed an all metal vacuum scroll pump without a tip seal material for evaluation. Although the initial, all metal version of the Air Squared pump was found deficient in regard to scroll impeller stiffness, which resulted in scroll contact, general design and pump performance was verified to be adequate. SRS PDRD Project 19039 was launched in 2019 as a 3rd attempt with Air Squared, Inc. in regard to development of an all metal vacuum scroll pump for consideration as an equivalent to the Eumeca/ Normetex pump. The effort specified 300 series stainless steel for the scroll impellers, all metal sealing, and design to meet tritium throughput and ultimate vacuum requirements. In addition, a 60 psig design pressure rating requirement was specified for the pump containment boundary. The 3rd generation Air Squared pump has been designed, fabricated, and has received preliminary testing. Preliminary testing has indicated proper leak tightness and pump performance. However, work continues regarding development of a pumping chamber containment bellows that can be subjected to 66 psig without damage to the bellows. Work will continue in 2020 and 2021 to pursue a pumping chamber containment bellows that meets the pressure rating requirement.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Assessing Suitable Geologic Carbon Storage Sites Across Utah

Utah has a wealth of potential geological reservoirs for carbon dioxide storage (CS) and a long history of geologic research resulting in an abundance of available subsurface data to evaluate CS potential. Reservoirs may include sandstone, carbonate, and basalt; these rock types are plentiful in Utah’s subsurface and the complex Phanerozoic history throughout the state requires evaluating each geologic region individually for promising reservoir-seal pairs for CO2 storage. Classifying Utah by geologic provinces (or “geo-regions”) allows for customized thinking about suitable CS reservoir and seal distribution, CO2 point sources, land use, and existing infrastructure. Preliminary results from this study highlight the geologic CS potential across 15 geo-regions. Four regions stand out as having high CS potential: the Uinta Basin, San Rafael Swell, Paradox Basin, and the southern Basin and Range Province. The Uinta Basin and San Rafael Swell geo-regions are well suited for CS and have several projects ongoing to evaluate Cretaceous Frontier and Naturita Formations, Jurassic Navajo Sandstone and Entrada Sandstone, and Permian Weber Sandstone reservoir units that lie beneath robust sealing units like the ~5000-ft-thick Mancos Shale and Carmel Formation. Reservoirs such as the Navajo and Weber Sandstones have been demonstrated to be suitable reservoirs through a long history of oil and gas exploration in Utah. New areas of interest include the southern Basin and Range in southwest Utah, where the Jurassic Navajo Sandstone is overlain by the sealing Carmel Formation at suitable depths (>3000 ft), and has good porosities based on outcrop analogue data. Just to the north (e.g., central Basin and Range), legacy wells and 2D seismic data show possible salt and subsurface basalt flows that may provide additional possible CS reservoirs and seals. This geo-region also has the advantage of being coupled with geothermal energy resources that may be used to power burgeoning direct air capture technologies. In the Paradox Basin of southeastern Utah, the Leadville Limestone is a potential storage reservoir beneath the thick (4000–5000 ft), salt-bearing Pennsylvanian Paradox Formation. Although the northern and western parts of Utah offer CS potential, these areas typically contain less infrastructure and subsurface penetrations, creating geologic uncertainty associated with subsurface seals and reservoirs due to a lack of data. Overall, this statewide assessment and ranking is the first step to aid in evaluating CS potential across Utah and provides a foundation for future research in the most favorable locations.

58 GEOSCIENCES↗
DOE OSTI2025

Pose Estimation for the Inspecta Project

In this addendum report we take the lessons learned from our initial generic object pose estimation research described in (Smartt, et al., 2025) and apply it to metal cup seals, which are attached to items after an international nuclear safeguards inspection (i.e., metal cup seals may be attached to containers of spent nuclear fuel after an inspector has measured and verified the material). We have also refined our software pipeline and training techniques since the final Inspecta report and will describe that process here. The objective of this task is to allow a robot to acquire images of the engraved seal characters to confirm that the correct seal is attached to the correct container. However, the seal may be attached in any orientation and therefore the robot manipulator arm with a camera needs to align with the normal face of the seal.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
DOE OSTI2022

Insulated exhaust port liner for a cylinder head assembly of a motor vehicle

An insulated exhaust port liner of a cylinder head assembly for fluidly connecting to an internal combustion engine of a motor vehicle includes a sealing layer. The sealing layer has a first surface defining a passage for fluidly connecting to the internal combustion engine and receiving exhaust gas. The sealing layer further includes a second surface opposite to the first surface. The liner further includes a thermal barrier layer coated onto the second surface of the sealing layer. The thermal barrier layer is a porous non-woven material for supporting the sealing layer on the cylinder head and reducing a transfer of heat from the sealing layer to the cylinder head.

Andruskiewicz, IV, Peter P.↗
DOE OSTI2023

Upscaling of asymmetric hollow fiber‐supported thin film membranes for oxygen separation from air: Proof of concept

Abstract Hollow fiber membranes demonstrate various advantages for high performance oxygen separation. However, the small diameters of hollow fibers and the brittleness of ceramics limit their mechanical strength, imposing great difficulties on stack and module development. Gas‐tight sealing is another challenge for upscaling of hollow fiber membrane technology. Low temperature sealant materials of epoxy resin or silicon are typically used for hollow fiber stacks, requiring that the sealing portions be located out of hot zone. Consequently, only partial length of hollow fibers participates in oxygen permeation. In this study, upscaling of our recently developed asymmetric hollow fiber‐supported thin film membranes is conducted, where individual hollow fibers are assembled in parallel to form a stack. A reliable gas‐tight sealing is obtained by combining ceramic paste with conductive adhesive ink cohesively. Comprehensive oxygen permeation test is conducted with the sealing portions being in hot zone and compared with a single hollow fiber membrane. Fundamental mechanism is discussed to understand the performances and their differences. An accelerated long‐term test (∼320 h, 16 thermal cycles) demonstrates excellent stability and robustness of the stack and sealing. The characterization of post‐test samples further confirms excellent stability and robustness of the phases and microstructures of the stack.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Geothermal play fairway analysis, part 1: Example from the Snake River Plain, Idaho

The Snake River Plain (SRP) volcanic province overlies the track of the Yellowstone hotspot, a thermal anomaly that extends deep into the mantle. Most of the area is underlain by a basaltic volcanic province that overlies a mid-crustal intrusive complex, which in turn provides the long-term heat flux needed to sustain geothermal systems. Previous studies have identified several known geothermal resource areas within the SRP. For the geothermal study presented herein, our goals were to: (1) adapt the methodology of Play Fairway Analysis (PFA) for geothermal exploration to create a formal basis for its application to geothermal systems, (2) assemble relevant data for the SRP from publicly available and private sources, and (3) build a geothermal PFA model for the SRP and identify the most promising plays, using GIS-based software tools that are standard in the petroleum industry. The study focused on identifying three critical resource parameters for exploitable hydrothermal systems in the SRP: heat source, reservoir and recharge permeability, and cap or seal. Data included in the compilation for heat source were heat flow, distribution and ages of volcanic vents, groundwater temperatures, thermal springs and wells, helium isotope anomalies, and reservoir temperatures estimated using geothermometry. Reservoir and recharge permeability was inferred from the analysis of stress orientations and magnitudes, post-Miocene faults, and subsurface structural lineaments based on magnetics and gravity data. Data for cap or seal included the distribution of impermeable lake sediments and clay-seal associated with hydrothermal alteration below the regional aquifer. These data were used to compile Common Risk Segment maps for heat, permeability, and seal, which were combined to create a Composite Common Risk Segment map for all southern Idaho that reflects the risk associated with geothermal resource exploration and identifies favorable resource tracks. Our regional assessment indicated that undiscovered geothermal resources may be located in several areas of the SRP. Two of these areas, the western SRP and Camas Prairie, were selected for more detailed assessment, during which heat, permeability, and seal were evaluated using newly collected field data and smaller grid parameters to refine the location of potential resources. These higher resolution assessments illustrate the flexibility of our approach over a range of scales.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

A constitutive model for glass–ceramic materials

Glass–ceramics have received recent attention for use in glass–ceramic to metal hermetic seals. Due to their heterogeneous microstructure, these materials exhibit a number of advantageous responses over conventional glass based seals. Key amongst them is the possibility of a controllable thermal strain response and apparent coefficient of thermal expansion which may be used to minimize thermally induced residual stresses for aforementioned seals. Furthermore, these behaviors result from an inorganic glass matrix and variety of crystalline ceramic phases including silica polymorph(s) that may undergo reversible solid-to-solid transformations with associated inelastic strain. Correspondingly, these materials exhibit complex thermomechanical responses associated with multiple inelastic mechanisms (viscoelasticity and phase transformation). While modeling these behaviors is essential for developing and analyzing the corresponding applications, no such model exists. Therefore, in this work a three-dimensional continuum constitutive model for glass–ceramic materials combining these various inelastic mechanisms is developed via an internal state variable approach. A corresponding fully implicit three dimensional numerical formulation is also proposed and implemented. The model is used to simulate existing experiments and validate the proposed formalism. As an example, the simple seal problem of a glass–ceramic seal inside a concentric metal shell is explored. Finally, the impact of the cooling rates, viscoelastic shift factors, and inelastic strain on final residual stress state are all investigated and the differing contributions highlighted.

36 MATERIALS SCIENCE↗
DOE OSTI2020

In-situ gloveport glove leak tester

The invention provides a system for detecting leaks in glovebox gloves, the system having a first seal within a glovebox aperture; a second seal contacting exterior surfaces of a glovebox, wherein the exterior surfaces define a periphery of the aperture; a first fluid supply for circumferentially expanding the first seal against center facing surfaces of the aperture to a first pressure; a second fluid supply for inflating the glove to a second pressure; and a pressure gauge for detecting a pressure decrease of the second pressure. Also provided is an in situ method for detecting leaks in glove box gloves, the method having the steps of applying a radially directed force to inside surfaces of cuffs of the gloves to hermetically seal the gloves from the exterior of the glovebox, thereby establishing a seal; inflating the gloves to a pressure; and monitoring the pressure for any decrease in pressure.

42 ENGINEERING↗
DOE OSTI2020

Lithium ion battery

A multi-core lithium ion battery includes a sealed enclosure and a support member disposed within the sealed enclosure. The sealed enclosure may be fabricated with a clamshell configuration. The sealed enclosure may further include at least two support members housed within individual compartments, separated by shared wall(s). The support member(s) includes a plurality of cavities and a plurality of lithium ion core members which are disposed within the plurality of cavities. The battery may further include a plurality of cavity liners, each of which is positioned between a corresponding one of the lithium ion core members and a surface of a corresponding one of the cavities. The hermetically sealed enclosure may be formed using a clamshell configuration. Structures may be included in proximity to or in contact with the lithium ion core members to control gas/fluid flow therefrom.

25 ENERGY STORAGE↗
DOE OSTI2021

Wellbore Leakage Mitigation Using Advanced Mineral Precipitation Strategies (Final Scientific/Technical Report)

This research project, entitled Wellbore Leakage Mitigation using Advanced Mineral Precipitation Strategies, was directed toward advancing mineral precipitation technologies to seal wellbore leaks and other potential carbon dioxide (CO 2 ) leakage pathways, including compromised wellbore cement and fracture networks of varying geometries throughout the wellbore and surrounding formation. The advanced mineral sealing techniques were evaluated in the laboratory and the field to expand the range of temperature, pressure, and chemical conditions where mineral precipitation could be used. Rates of enzymatically or thermally induced calcium carbonate precipitation (EICP, TICP) were determined as well as rates of enzyme inactivation at elevated temperatures (>60 °C). Immobilization was shown to enhance the thermal stability of urease enzyme and provide protection from inhibition in low pH conditions. Mineral seals promoted by EICP and TICP were used to seal fractured composite (cement/sandstone) and shale cores in high pressure reactors operated at temperatures greater than 55 °C and 130 °C, respectively. A computational model was updated to model processes of EICP and TICP. The work resulted in a successful field test, which showed that EICP in the presence of low pH fluids (CO 2 -impacted brine) could promote permeability reduction and seal a channel in the near-wellbore environment.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

An Improved Model For Determining Salinity Recharge Time for Deep Borehole Disposal - 20405

In a previous publication (K. P. Travis, D. Burley and F. G. F. Gibb, WM2017 Conference, Phoenix Arizona paper no. 17480) we introduced a numerical model to estimate the time it would take for a pressure perturbation to subside following its creation from the construction of a deep geological borehole in water-saturated rock. The model was based on the notion of a point source of momentum - a solution of the time-dependent pressure-diffusion equation. Using the model, we estimated that it would take on the order of 10 k years for physical equilibrium to become re-established following the sinking of a 5 km borehole in granite. The significance of such a model is that it places an upper bound on the lifetime required of a borehole sealing system - a necessary input to a borehole post-closure safety case assessment. No engineered sealing system has ever been devised which is capable of retaining its sealing properties for 10 half-lives of long-lived radioisotopes in spent fuel or high-level waste. One of the key advantages of disposing of nuclear waste via Deep Borehole Disposal (DBD) is the natural sealing provided by density stratified groundwater. Upon sinking of a borehole, and subsequent filling with fresh water, brine or drilling mud, this natural barrier may be temporarily damaged. Over time, fresh brine from the far-field will flow towards or away from the hole (driven by a pressure gradient) and will eventually re-establish the original salinity gradient. It follows that the engineered seals need last only as long as the time required for this salinity gradient to reset itself. One of the limitations of our previous model was the use of a static boundary condition on the borehole wall. The model used a boundary pressure which varied quadratically with depth (arising from differences between the pressure of a column of fresh water in the borehole and that of a column of brine in the host rock). However as brine replaces fresh water in the borehole (driven by a pressure gradient), the boundary function must change with time. We now introduce an improved model which takes this time dependent boundary condition into account. The model also takes into account the time taken for a mixture of brine and fresh water to re-establish chemical equilibrium through the process of diffusion. The paper contains the mathematical details of our new iterative model as well as results showing the time taken to reach steady state, and concentration profiles for the components of the brine-filled borehole as a function of time together with a discussion on the implications of the results for developing a post-closure safety assessment for DBD. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Towards Polymer-Free, Femto-Second Laser-Welded Glass/Glass Solar Modules

This project explores the use of femto-second (fs) lasers to form glass-to-glass welds for hermetically sealed, polymer-free solar modules. Low iron solar glass coupons were welded together without the use of glass filler using a fs laser with dedicated optics to elongate the focal plane parallel to the incident beam. The resulting welds were then stress tested to failure to reveal the critical stress intensity factor, KIc. These values were used in a structural mechanics model of a 1 m by 2 m glass/glass module under a simulated static load test. The results show that the fs laser welds are strong enough for a suitably framed module to pass the IEC 61215 static load test with a load of 5400 Pa. Key to this finding is that the module must be framed and braced, and the glass must be ribbed to allow pockets for the cells and welds inside the border of the module. The result is a module design that is completely polymer-free, hermetically sealed, has improved thermal properties, and is easily recycled.

femto-second laser welded↗
DOE OSTI2024

Beyond the Surface: Non-Invasive Low-Field NMR Analysis of Microbially-Induced Calcium Carbonate Precipitation in Shale Fractures

Microbially-induced calcium carbonate precipitation (MICP) is a biological process in which microbially-produced urease enzymes convert urea and calcium into solid calcium carbonate (CaCO 3 ) deposits. MICP has been demonstrated to reduce permeability in shale fractures under elevated pressures, raising the possibility of applying this technology to enhance shale reservoir storage safety. For this and other applications to become a reality, non-invasive tools are needed to determine how effectively MICP seals shale fractures at subsurface temperatures. In this study, two different MICP strategies were tested on 2.54 cm diameter and 5.08 cm long shale cores with a single fracture at 60 °C. Flow-through, pulsed-flow MICP-treatment was repeatedly applied to Marcellus shale fractures with and without sand (“proppant”) until reaching approximately four orders of magnitude reduction in apparent permeability, while a single application of polymer-based “immersion” MICP-treatment was applied to an Eagle Ford shale fracture with proppant. Low-field nuclear magnetic resonance (LF-NMR) and X-Ray computed microtomography (micro-CT) techniques were used to assess the degree of biomineralization. With the flow-through approach, these tools revealed that while CaCO 3 precipitation occurred throughout the fracture, there was preferential precipitation around proppant. Without proppant, the same approach led to premature sealing at the inlet side of the core. In contrast, immersion MICP-treatment sealed off the fracture edges and showed less mineral precipitation overall. This study highlights the use of LF-NMR relaxometry in characterizing fracture sealing and can help guide NMR logging tools in subsurface remediation efforts.

MICP↗
DOE OSTI2025

Designing a repository in domal salt: The influence of design variants in different modelling environments

To understand the long-term environmental impact of disposing radioactive waste of in a deep geological repository and to optimise its design, performance assessments are used. In this study, four teams (COVRA, GRS, Quintessa, and DOE) modified the previously developed generic repository of DECOVALEX task F2 to identify commonalities and differences between the teams for specific changes in repository design. The teams tested six design modifications: (1) Replacing concrete abutments with run-of-mine salt; (2) Replacing the salt seal with a concrete abutment and using run-of-mine salt instead for the two concrete abutments in each drift seal; (3) Halving the size of the infrastructure area; (4) Using run-of-mine salt instead of gravel for backfilling the infrastructure area; (5) Disposal of spent nuclear fuel without the POLLUX-10 containers (6); Lower initial saturation of the spent nuclear fuel and vitrified waste disposal drifts. Despite different modelling strategies used, models agreed that a smaller infrastructure area has a limited effect on radionuclide transport. Responses to the absence of the two concrete abutments in each seal, the use of single large concrete abutments (200 m each), or the use of run-of-mine salt in the infrastructure area differ between teams due to differing modelling assumptions. Based on these results, the estimated efficacy of containment depends strongly on the model assumptions of each team. More specifically, it appears to depend on the compaction model used and therefore on the backfill material used in different areas of the repository. However, the drift seal appears to be a critical design element in all models, effectively limiting radionuclide transport by hydrologically disconnecting sections of the repository. Additional beneficial design choices include the use of dry salt in disposal drifts to limit radionuclide transport and reducing the infrastructure area costs and minimizing host rock damage.

DECOVALEX↗