Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “runaway”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Heat Generation versus Heat Dissipation Maps for Batteries (Battery Safety Maps) [SWR-21-27]

NREL's Battery Safety Map (Heat Generation versus Heat Dissipation Maps for Batteries) generates a response surface that is grouped into regions where the battery is deemed safe from the propagation of thermal runaway, those where an engineering solution would render the battery safe, and finally instances where thermal runaway is inevitable. The demarcation for the different regions is provided by specifications or constraints imposed by the end user. NREL's Battery Safety Map is a user-defined subroutine that sweeps through a set of parameters describing the operating conditions and short-circuit scenarios for battery safety simulations. For each run, the electrochemical-thermal model implementing reaction kinetics and gas generation are run to evaluate the amount of heat generated. A thermal model then captures the amount of heat dissipation based on boundary conditions defined (e.g., forced convection, constant temperature at the surface, etc.). Based on the rate of heat transfer and the amount of heat generated, each run is classified into "safe," "mitigation possible," or "unsafe" zones. These categories are defined based on constraints or tolerance specifications provided by the end user.

Santhanagopalan, Shriram↗
DOE OSTI2026

The 10 September 2025 M w 4.1 Earthquake in Northeastern Utah, United States: An Archetypal Continental Mantle Event

The 10 September 2025 M w 4.1 earthquake in northeastern Utah, United States, had a focal depth 68 km beneath sea level, which is ∼20–25 km greater than estimates of local crustal thickness, making it a rare example of a continental mantle earthquake (CME). The focal depth is well resolved from arrival-time inversion (nearest station ∼13 km away) and moment tensor inversion of regional waveforms. Similar to other CMEs in the Intermountain West, there were no obvious aftershocks or foreshocks, and the waveforms were enriched in high-frequency energy. Spectral modeling gives a stress drop of ∼80 MPa and a radiation efficiency of ∼0.08, albeit with large uncertainties. The high stress drop and low radiation efficiency are consistent with a dissipative source process such as thermal runaway. Also similar to previous Intermountain West CMEs, the event occurred along the boundary of the Archean Wyoming craton, where pressure–temperature conditions favor ductile deformation. We hypothesize that edge-driven or regional-scale mantle convection produces increased strain rates near the craton boundary that make either conventional brittle failure or thermal runaway feasible at relatively high pressure–temperature conditions. High conductivity inferred around the edge of the craton may suggest that fluids also contribute to CME occurrence.

Koper, Keith D. [Univ. of Utah, Salt Lake City, UT↗
DOE OSTI2020

Evaluation of Multi-cell Failure Propagation

Failure propagation testing is of increasing interest to the designers and end users of battery systems. One of the chief difficulties, however, is choosing an appropriate initiation method to perform the test. Single cell abuse testing is typically used to initiate thermal runaway but this can involve a large amount of additional energy injected into the system. It is assumed that this will have some impact on the behavior of a propagating thermal runaway event, but there is little data available as to how significant this would be. Further, it is ultimately difficult to develop viable propagation tests for compliance and public safety activities without better knowledge of how test methods will impact the results. This work looks at propagating battery failure with a variety of chemistries, formats, configurations and initiation methods to determine the level of significance of the chosen initiation method on the test results. We have ultimately found while there is some impact on the detailed results of propagation testing, in most cases other factors, particularly the energy density of the system play a much greater role in the likelihood of a propagation event consuming an entire battery. We have also provided some guidelines for test design to support best practices in testing.

25 ENERGY STORAGE↗
DOE OSTI2022

Lithium-Ion Batteries with Safer Current Collectors

The US Department of Energy’s Oak Ridge National Laboratory and Soteria Battery Innovation Group collaborated to develop a metallized polymer film as a current collector for lithium-ion batteries and design slit patterns for electrodes to improve battery safety. The metallized polymer film serves as a fuse that will break under high temperature resulting from a short circuit. Consequently, the short circuit will be broken and the heat generated from the short circuit will be alleviated to avoid thermal runaway. The electrodes with slit patterns are expected to be broken into small segments upon mechanical impact, which can isolate the damaged electrodes from the rest. Thus, the heat generation associated with the mechanical impact will be reduced, along with the likelihood of thermal runaway. This effort aimed to improve lithium-ion battery safety by replacing traditional metal foils with metallized polymer films as current collector and introducing slit patterns to battery electrodes. The metallized polymer films were polyethylene terephthalate with a thin metal (aluminum for cathodes and copper for anodes) coating on both sides. Slit patterns with various geometries and dimensions were designed via simulation. Temperature distribution on cells with electrodes with and without slit patterns was also simulated via nemerical modeling. Electrodes on traditional metal foils and metallized polymer films were coated via a pilot-scale slot-die coater at the US Department of Energy Battery Manufacturing Facility at Oak Ridge National Laboratory. The electrodes were calendered to 35% porosity and punched out with and without slit patterns. Pouch cells were assembed with the electrodes inside a dry room for electrochemical and safety testing. Electrodes coated on metallized polymer films exhibited comparable electrochemical performance to their counterparts coated on traditional metal foils. They also showed improved safety in nail penetration and indentation tests.

25 ENERGY STORAGE↗
DOE OSTI2026

MAT 332: Recyclable-By-Design Carbon Fiber Composites for Battery Enclosures

This work aims to fabricate a small-scale battery module with the baseline RBD-CFRC and conduct mechanical crush test to develop an initial thermal runaway model. Test the adhesive properties of the RBD-CFRCs using their resin constituent, ultrasonic welding, and other resins employed today. Recommend a future direction for resin development to enable the welding of RBDCFRCs to dissimilar materials. Time and Cost Permitting. Iterate on resin development for flame resistance and adhesive properties, demonstrating how thermal runaway can be reduced or joining properties can be improved.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

MOA-2009-BLG-319Lb: A Sub-Saturn Planet inside the Predicted Mass Desert

We present an adaptive optics (AO) analysis of images from the Keck II telescope NIRC2 instrument of the planetary microlensing event MOA-2009-BLG-319. The ∼10 yr baseline between the event and the Keck observations allows the planetary host star to be detected at a separation of 66.5 ± 1.7 mas from the source star, consistent with the light-curve model prediction. The combination of the host star brightness and light-curve parameters yields host star and planet masses of M {sub host} = 0.524 ± 0.048M {sub ⊙} and m {sub p} = 67.3 ± 6.2M {sub ⊕} at a distance of D {sub L} = 7.1 ± 0.7 kpc. The star−planet projected separation is 2.03 ± 0.21 au. The planet-to-star mass ratio of this system, q = (3.857 ± 0.029) × 10{sup −4}, places it in the predicted “planet desert” at 10{sup −4} < q < 4 × 10{sup −4} according to the runaway gas accretion scenario of the core accretion theory. Seven of the 30 planets in the Suzuki et al. sample fall in this mass ratio range, and this is the third with a measured host mass. All three of these host stars have masses of 0.5 ≤ M {sub host}/M {sub ⊙} ≤ 0.7, which implies that this predicted mass ratio gap is filled with planets that have host stars within a factor of two of 1M {sub ⊙}. This suggests that runaway gas accretion does not play a major role in determining giant planet masses for stars somewhat less massive than the Sun. Our analysis has been accomplished with a modified DAOPHOT code that has been designed to measure the brightness and positions of closely blended stars. This will aid in the development of the primary method that the Nancy Grace Roman Space Telescope mission will use to determine the masses of microlens planets and their hosts.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Alcator C-Mod: Research in support of ITER and steps beyond

This paper presents an overview of recent highlights from research on Alcator C-Mod. Significant progress has been made across all research areas over the last two years, with particular emphasis on divertor physics and power handling, plasma-material-interaction studies, ELM-suppressed pedestal dynamics, core transport and turbulence, and RF heating and current drive utilizing Ion Cyclotron and Lower Hybrid tools. Specific results of particular relevance to ITER include: inner wall SOL transport studies that have led, together with results from other experiments, to the change of the detailed shape of the inner wall in ITER; runaway electron studies showing that the critical electric field required for runaway generation is much higher than predicted from collisional theory; core tungsten impurity transport studies reveal that tungsten accumulation is naturally avoided in typical C-Mod conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Overview of the TCV tokamak program: Scientific progress and facility upgrades

The TCV tokamak is augmenting its unique historical capabilities (strong shaping, strong electron heating) with ion heating, additional electron heating compatible with high densities, and variable divertor geometry, in a multifaceted upgrade program designed to broaden its operational range without sacrificing its fundamental flexibility. The TCV program is rooted in a three-pronged approach aimed at ITER support, explorations towards DEMO, and fundamental research. A 1 MW, tangential neutral beam injector (NBI) was recently installed and promptly extended the TCV parameter range, with record ion temperatures and toroidal rotation velocities and measurable neutral-beam current drive. ITER-relevant scenario development has received particular attention, with strategies aimed at maximizing performance through optimized discharge trajectories to avoid MHD instabilities, such as peeling-ballooning and neoclassical tearing modes. Experiments on exhaust physics have focused particularly on detachment, a necessary step to a DEMO reactor, in a comprehensive set of conventional and advanced divertor concepts. The specific theoretical prediction of an enhanced radiation region between the two X-points in the low-field-side snowflake-minus configuration was experimentally confirmed. Fundamental investigations of the power decay length in the scrape-off layer (SOL) are progressing rapidly, again in widely varying configurations and in both D and He plasmas; in particular, the double decay length in L-mode limited plasmas was found to be replaced by a single length at high SOL resistivity. Experiments on disruption mitigation by massive gas injection and electron-cyclotron resonance heating (ECRH) have begun in earnest, in parallel with studies of runaway electron generation and control, in both stable and disruptive conditions; a quiescent runaway beam carrying the entire electrical current appears to develop in some cases. Developments in plasma control have benefited from progress in individual controller design and have evolved steadily towards controller integration, mostly within an environment supervised by a tokamak profile control simulator. TCV has demonstrated effective wall conditioning with ECRH in He in support of the preparations for JT-60SA operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

The Impact of Anomalous Resistivity in Vacuum Contaminant Plasmas on the Electrothermal Instability

This manuscript presents an assessment of the electrothermal instability (ETI) in the presence of anomalous resistivity (AR) in vacuum contaminant plasmas (VCP) when applied to a magnetized liner inertial fusion (MagLIF)-like load.Pulsed-power driven dielectrically coated metallic liners, like in MagLIF, experience the current-driven electrothermal instability which occurs when a material’s resistivity changes with temperature and is subject to ohmic heating. Large scale pulsed-power facilities that use magnetically insulated transmission lines (MITL) have been shown to generate low-density plasma which enters the target chamber and coalesces around the load. The low-density high-temperature vacuum contaminant plasmas (VCP) can parasitically divert current from the load through causing a short in the anode-cathode gap inside the target chamber. Resistive magnetohydrodynamic (MHD) simulations of these VCP experience unphysical runaway ohmic heating due to under predicting the resistivity by using a purely collisional resistivity model.AR provides a physics-based way to address this runaway heating through increasing the resistivity in a proportional way with the drift speed. In this work, 1D simulations probe the effect that AR in VCP has on the magnetic diffusion rate, and 2D simulations show how this effect manifests in the nonlinear striation form of the ETI for a MagLIF-like load. Beryllium and aluminum dielectrically coated liners are used for the 1D and 2D simulations in this work. The1D simulations show that a VCP causes a delay in the current delivery to the load by upwards of 8 ns at 60 ns into atypical current pulse for an 1 × 10 7 A scale pulsed-power accelerator. The 2D simulations show the delay observed in the 1D simulations is reduced substantially (4 ns) by 2D turbulence that disrupts the VCP layer early in time. Here, the 2Dsimulated ETI growth varies across AR models, more so for the beryllium liner than the aluminum liner because the beryllium liner shows an enhanced rate of penetration for the magnetic diffusion wave in comparison to the aluminum liner. The 2D simulations show the bulk dielectric thickness varies across AR models with the Davidson AR model beingthe largest and the Buneman AR model being the smallest, and in connection with the thickness the Rayleigh-Taylor bubble-spike distances varies correspondingly.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Design of passive and structural conductors for tokamaks using thin-wall eddy current modeling

Abstract A new three-dimensional electromagnetic modeling tool ( ThinCurr ) has been developed using the existing PSI-Tet finite-element code in support of conducting structure design work for both the SPARC and DIII-D tokamaks. Within this framework a 3D conducting structure model was created for both the SPARC and DIII-D tokamaks in the thin-wall limit. This model includes accurate details of the vacuum vessel and other conducting structural elements with realistic material resistivities. This model was leveraged to support the design of a passive runaway electron mitigation coil (REMC), studying the effect of various design parameters, including coil resistivity, current quench duration, and plasma vertical position, on the effectiveness of the coil. The REMC is a non-axisymmetric coil designed to passively drive large non-axisymmetric fields during the plasma disruption thereby destroying flux surfaces and deconfining RE seed populations. These studies indicate that current designs should apply substantial 3D fields at the plasma surface during future plasma current disruptions as well as highlight the importance of having the REMC conductors away from the machine midplane in order to ensure they are robust to off-normal disruption scenarios.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Hierarchical Cellulose Superinsulation Membrane

The environment-friendly components coupled with the ability to mimic the simplicity and originality of nature necessitate advanced sustainable materials with structural capabilities for energy-efficient applications. The use of feedstock deriving from plant-based, renewable organic material to produce nanofibril that embodies enhanced insulating properties and high mechanical strength constitutes an efficient development strategy. In this work, a free-standing, hierarchical superinsulation membrane by leveraging the principle of the bottom-up method is reported. The electrospun cellulose nanofibrils/aerogel-based core layer provides exceptional thermal properties with its thermal conductivity of 10.2 mW m –1 K –1 . The lightweight, flexible, and durable paper-like membrane features a tensile strength of 11.3 MPa and a bending rigidity in the order of 4.6 cN mm –1 . The hydrophobic superinsulation membrane material also exhibits a ΔT of ≈25 °C under continuous sunlight illumination and allows thermal runaway mitigation of rechargeable lithium-ion batteries. All the aforementioned properties position this hybrid superinsulation membrane as a promising material for energy-saving thermal management applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Simultaneously Blocking Chemical Crosstalk and Internal Short Circuit via Gel-Stretching Derived Nanoporous Non-Shrinkage Separator for Safe Lithium-Ion Batteries

The separator, an ionic permeable and electronic insulating membrane between cathode and anode, plays a crucial role in the electrochemical and safety performance of batteries. However, the commercial polyolefin separators not only suffer from inevitable thermal shrinkage at elevated temperature, but also fail to inhibit the hidden chemical crosstalk of reactive gases such as O 2 , leading to often reported thermal runaway (TR) and hence preventing large-scale implementation of high-energy-density lithium-ion batteries. Herein, a nanoporous non-shrinkage separator (GS-PI) was fabricated via a novel gel-stretching orientation approach to eliminate TR. In situ synchrotron small angle X-ray scattering during heating clearly showed that the as-prepared thin GS-PI separator exhibits superior mechanical tolerance at high temperature, thus effectively preventing internal short circuit. Meanwhile, the unique nanoporous structure design further blocks chemical crosstalk and the associated exothermic reactions. Accelerating Rate Calorimetry test revealed that the practical 1 Ah LiNi 0.6 Co 0.2 Mn 0.2 O 2 (NCM622)/graphite pouch cell using GS-PI nanoporous separator show a maximum temperature rise (dT/dt max ) of only 3.7 °C s -1 compared to 131.6 °C s -1 in the case of Al 2 O 3 @PE macroporous separator. Furthermore, despite the reduced pore size, the GS-PI separator demonstrates better cycling stability than conventional Al 2 O 3 @PE separator at high temperature without sacrificing specific capacity and rate capability.

25 ENERGY STORAGE↗
DOE OSTI2021

Multiscale Understanding of Surface Structural Effects on High-Temperature Operational Resiliency of Layered Oxide Cathodes

The worldwide energy demand in electric vehicles and the increasing global temperature have called for development of high-energy and long-life lithium-ion batteries (LIBs) with improved high temperature operational resiliency. However, current attention has been mostly focused on cycling aging at elevated temperature, leaving considerable gaps of knowledge in the failure mechanism and practical control of abusive calendar aging and thermal runaway that are highly related to the eventual operational lifetime and safety performance of LIBs. Herein, using a combination of various in situ synchrotron X-ray and electron microscopy techniques, we report a multiscale understanding of surface structure effects involved in regulating the high temperature operational tolerance of polycrystalline Ni-rich layered cathodes. Our results collectively show that an ultraconformal poly (3,4-ethylenedioxythiophene) coating can effectively prevent LiNi 0.8 Co 0.1 Mn 0.1 O 2 cathode from undesired phase transformation and transition metal dissolution on the surface, atomic displacement and dislocations within primary particles, intergranular cracking along the grain boundaries within secondary particles, and intensive bulk oxygen release during high state-of-charge and high temperature aging. As a result, the present work highlights the essential role of surface structure controls in overcoming the multiscale degradation pathways of high-energy battery materials at extreme temperature.

25 ENERGY STORAGE↗
DOE OSTI2023

Comprehensive Battery Safety Risk Evaluation: Aged Cells versus Fresh Cells Upon Mechanical Abusive Loadings

Abstract Despite their wide applications, lithium‐ion batteries (LIBs) have been struggling with their safety risks arising from different lifetime stages. Here, the NCMA pouch cell is taken as an example, and the safety of both fresh and aged cells from three milestone stages, that is, internal short circuit (ISC) triggering risk, ISC mode, and the subsequent thermal runaway (TR) consequence is investigated. By combining mechanical abusive testing and physics‐based models on commercialized cells with various states‐of‐health (SOH) and states‐of‐charge, it is discovered that the ISC triggering delays with the decay of SOH and soft ISC mode will be triggered more frequently, which is mainly due to the mechanical behaviors of the current collectors. The temperature rises and peak temperature during the subsequent TR also become milder for aged cells due to the reduced capacity and deterministic soft ISC process. Results here provide a mechanistic explanation of the safety risk comparison between the fresh and aged cells, offering cornerstone guidance to the evaluation and design of next‐generation safer LIBs.

25 ENERGY STORAGE↗
DOE OSTI2024

Dynamics of Intra-Cell Thermal Front Propagation in Lithium-Ion Battery Safety Issues

Thermal runaway (TR), a critical failure mode in lithium-ion batteries (LIBs), poses significant safety risks and hinders wider application of LIBs. TR typically begins at a localized heat source and spreads across the cell. Understanding thermal front propagation (TFP) characteristics, such as front and velocity, is crucial for assessing energy release and temperature distribution for battery hazardous estimation. Recent studies assume that TR within cells propagates at a near-constant velocity, based on the reaction kinetics and thermal properties. Here, in this study, an intra-battery TR model is further proposed and it indicates that TFP velocity stabilizes when the front is distanced from the heat source. Theoretical estimates for propagation velocity and front are developed and validated through numerical simulations and experimental tests from the NREL Battery Failure Databank. The energy release rate during TFP and the impact of preheating based on a point heat source are explored. This work clarifies the long-standing clouds of the thermal font propagation behaviors within the single cell, highlights the power and beauty of mathematics modeling to describe the complicated thermal behaviors, and provides important guidelines for thermal hazardous understanding for next-generation batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Swelling and permeability effects during propellant cookoff

Large rocket motors may violently explode when exposed to accidental fires. Even hot metal fragments from a nearby accident may penetrate the propellant and ultimately cause thermal ignition. A mechanistic understanding of heated propellants leading to thermal runaway is a major unsolved problem. Here we show that thermal ignition in propellants can be predicted using a universal cookoff model coupled to a micromechanics pressurization model. Our model predicts the time to thermal ignition in cookoff experiments with variable headspace volumes. Furthermore, we found that experiments with headspace volumes are more prone to deformation which distorts pores and causes increased permeability when the propellant expands into this headspace. Delayed ignition with larger headspace volume correlates with lower headspace pressures during decomposition. We found that our predictions matched experimental measurements best when the initial propellant was impermeable to gas flow rather than being permeable. Similar behavior is expected with other energetic materials with rubbery binders. Our model is validated using data from a separate laboratory. We also present an uncertainty analysis using Latin Hypercube Sampling (LHS) of thermal ignition caused by a steel fragment embedded in the propellant.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Development of cathode-electrolyte-interphase for safer lithium batteries

Accompanied by the adoption of aggressive cathodes to continuously improve batteries energy density, enhancing their safety is becoming increasingly urgent for the electric vehicle development. In-situ controllable formation of robust cathode-electrolyte interphase (CEI) with high inorganic content seems to be the most promising strategy to address the thermal runaway concerns. Moreover, the in-situ formation strategy via suitable electrolyte replacement or electrolyte additives is extremely simple yet effective, especially for industrial manufacture of batteries. Here, this paper briefly reviews recent advanced CEIs formed by conventional carbonate-based electrolytes, fluorinated electrolytes, concentrated electrolytes, and solid state electrolytes. The focus on the thermal stability of the cathodes after CEI modification, and at the same time conduct safety tests at the material, cell, and module levels for comprehensive evaluation are encouraged. The review will provide inspiration for future developments in battery safety and push forward the practical applications of newly developed high-energy density batteries.

25 ENERGY STORAGE↗