Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “radiality”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Radial turbine cooling

Radial turbines have been used extensively in many applications including small ground based electrical power generators, automotive engine turbochargers and aircraft auxiliary power units. In all of these applications the turbine inlet temperature is limited to a value commensurate with the material strength limitations and life requirements of uncooled metal rotors. To take advantage of all the benefits that higher temperatures offer, such as increased turbine specific power output or higher cycle thermal efficiency, requires improved high temperature materials and/or blade cooling. Extensive research is on-going to advance the material properties of high temperature superalloys as well as composite materials including ceramics. The use of ceramics with their high temperature potential and low cost is particularly appealing for radial turbines. However until these programs reach fruition the only way to make significant step increases beyond the present material temperature barriers is to cool the radial blading.

Roelke, Richard J.↗
NASA NTRS1992

Comparison of diffusion and particle drift descriptions of radial transport in the earth's inner magnetosphere

The paper compares two approaches for describing the radial motion of charged particles in the equatorial plane of the earth's magnetosphere: the radial diffusion and the guiding-center drift. For this purpose, a time-dependent observation-based model electrostatic field is computed for the August 1990 storm event, and this field is used to (1) calculate the guiding-center drift of a ring of monoenergetic test particles and (2) compute the specific radial diffusion coefficient and solve the relevant diffusion equation. Generally, only fair agreement was found between the guiding-center and the diffusion calculation approaches. The best agreement could be obtained for the case of a series of small storms rather than for one substantial storm.

Riley, Pete↗
NASA NTRS1993

Radial transport of storm time ring current ions

Radial transport of energetic ions for the development of the main phase of geomagnetic storms is investigated with data from the medium energy particle analyzer (MEPA) on the Charge Composition Explorer spacecraft, which monitored protons, helium ions, and the carbon-nitrogen-oxygen group, which is mostly dominated by oxygen ions. From a study of four geomagnetic storms, we show that the flux increase of these ions in the inner ring current region can be accounted for by an inward displacement of the ring current population by 0.5 to 3.5 R(E). There is a general trend that a larger inward displacement occurs at higher L shells than at lower ones. These results are in agreement with previous findings. The radially injected population consists of the prestorm population modified by substorm injections which occur on a much shorter time scale than that for a storm main phase. It is also found that the inward displacement is relatively independent of ion mass and energy, suggesting that the radial transport of these energetic ions is effected primarily by convective motion from a large electric field or by diffusion resulting from magnetic field fluctuations.

Lui, A. T. Y.↗
NASA NTRS1993

Spatially extensive uniform stress fields on Venus inferred from radial dike swarm geometries: The Aphrodite Terra example

The high resolution and near global coverage of Magellan radar images is facilitating attempts to systematically investigate the stresses that have deformed the venusian crust. Here we continue earlier efforts to utilize approximately 170 large, radially lineated structures interpreted as dike swarms to assess the orientation of the regional maximum horizontal compressive stress (MHCS) which existed in their vicinities during emplacement. Examination of swarms near the equator reveals a link to broad scale regional structures, such as Aphrodite Terra, across distances in excess of 1000 km, suggesting the existence of first order stress fields which affect areas of more than 10(exp 6) sq km in a uniform fashion. Focusing further upon the Aphrodite Terra region, the MHCS field in the surrounding lowlands inferred from radial swarms is oriented approximately normal to the slope of the highland topography. This stress configuration appears, at a simple level, to be incompatible with that expected during either upwelling or downwelling construction of the highlands. In addition, the relatively undeformed geometry of the radial structures within the highlands implies that these dike swarm features formed more recently than their highly deformed surroundings. We conclude that the differential stresses which existed during emplacement of the dike swarms within and adjacent to the Aphrodite Terra highlands are related to the gravitational relaxation of pre-existing topography.

Grosfils, Eric B.↗
NASA NTRS1991

Radial evolution of the solar wind turbulence with application to charged particle transport

The proposed research efforts funded by the Pioneer-Venus Guest Investigator Grant to the Bartol Research Institute center on a study of the radial and temporal variation of the large-scale interplanetary magnetic field (IMF) and include a study of the radial variation of the observed north-south asymmetry of the IMF spiral based on the previous results of Bieber (1988). The preliminary results of Bieber demonstrated that at Earth orbit there exists an asymmetry between the yearly average winding angles of toward and away sector fields that can be as large as 10 degrees. The Bieber (1988) analysis employed the NSSDC omnitape data set of 1 AU measurements. When the observed asymmetry is related to the state of the solar magnetic dipole, it is possible to conclude that the IMF north of the heliospheric current sheet is more tightly wound than the IMF spiral south of the current sheet. The average difference in the winding angle as measured over a 21 year period spanning 1965 through 1985 was 3.1 degrees + 1.1 degrees. The Bieber analysis was able to rule-out several possible sources for the observed behavior including a possible asymmetry in the solar wind speed or the observed hemispherical dependence of solar rotation. The object of this research was to extend this previous result to include observations within the inner and outer heliosphere, to examine the radial dependence of the reported asymmetry, and to better resolve the possible source of the observations. The Pioneer-Venus Orbiter has proven to be the perfect monitor for the inner heliospheric observations. It has provided 9 years of continuous observations at a fixed heliocentric distance (except for those periods when the spacecraft was within the region of space where the magnetic field is influenced by the presence of the planet). Comparisons between the 1 AU observations recorded on the NSSDC omnitape and the 0.7 AU observations of the Pioneer-Venus Orbiter have greatly improved our understanding of the IMF winding angle asymmetry. Further comparison with outer heliospheric measurements have proven interesting, although less conclusive.

Smith, Charles W.↗
NASA NTRS1993

Radial distribution of metallicity in the LMC cluster systems

New determinations of the deprojected distances to the galaxy center for 94 star clusters and their metal abundances are used to investigate the variation of metallicity across the two LMC star cluster systems (Kontizas et al. 1990). A systematic radial trend of metallicity is observed in the extended outer cluster system, the outermost clusters being significantly metal poorer than the more central ones, with the exception of six clusters (which might lie out of the plane of the cluster system) out of 77. A radial metallicity gradient has been found, qualitatively comparable to that of the Milky Way for its system of the old disk clusters. If the six clusters are taken into consideration then the outer cluster system is well mixed up to 8 kpc. The spatial distribution of metallicities for the inner LMC cluster system, consisting of very young globulars does not show a systematic radial trend; they are all metal rich.

Kontizas, M.↗
NASA NTRS1994

Supersymmetry and radial squeezed states for Rydberg wave packets

Atomic supersymmetry provides an analytical effective-potential model useful for describing certain aspects of Rydberg atoms. Experiments have recently demonstrated the existence of Rydberg wave packets localized in the radial coordinated with p-state angular distribution. This paper shows how atomic supersymmetry can be used to treat radial Rydberg wave packets via a particular analytical type of squeezed state, called a radial squeezed state.

Bluhm, Robert↗
NASA NTRS1994

A simulation study of radial expansion of an electron beam injected into an ionospheric plasma

Injections of nonrelativistic electron beams from a finite equipotential conductor into an ionospheric plasma have been simulated using a two-dimensional electrostatic particle code. The purpose of the study is to survey the simulation parameters for understanding the dependence of beam radius on physical variables. The conductor is charged to a high potential when the background plasma density is less than the beam density. Beam electrons attracted by the charged conductor are decelerated to zero velocity near the stagnation point, which is at a few Debye lengths from the conductor. The simulations suggest that the beam electrons at the stagnation point receive a large transverse kick and the beam expands radially thereafter. The buildup of beam electrons at the stagnation point produces a large electrostatic force responsible for the transverse kick. However, for the weak charging cases where the background plasma density is larger than the beam density, the radial expansion mechanism is different; the beam plasma instability is found to be responsible for the radial expansion. The simulations show that the electron beam radius for high spacecraft charging cases is of the order of the beam gyroradius, defined as the beam velocity divided by the gyrofrequency. In the weak charging cases, the beam radius is only a fraction of the beam gyroradius. The parameter survey indicates that the beam radius increases with beam density and decreases with magnetic field and beam velocity. The beam radius normalized by the beam gyroradius is found to scale according to the ratio of the beam electron Debye length to the ambient electron Debye length. The parameter dependence deduced would be useful for interpreting the beam radius and beam density of electron beam injection experiments conducted from rockets and the space shuttle.

Koga, J.↗
NASA NTRS1993

Radially fractured domes: A comparison of Venus and the Earth

Radially fractured domes are large, tectonic and topographic features discovered on the surface of Venus by the Magellan spacecraft. They are thought to be due to uplift over mantle diapirism, and to date are known to occur only on Venus. Since Venus and the Earth are grossly similar in size, composition and structure, we seek to understand why these features have not been seen on the Earth. We model the uplift and fracturing over a mantle diapir as functions of lithospheric thickness and diapir size and depth. We find that lithospheres of the same thickness on the Earth and Venus should respond similarly to the same sized diapir, and that radially fractured domes should form most readily in thin oceanic lithospheres on Earth if diapiric activity is similar on the two planets. However, our current knowledge of the Earth's oceanic floors is insufficient to confirm or deny the presence of radially fractured domes. We compute the expected dimensions for these features on the Earth and suggest a search for them to determine whether mantle diapirism operates similarly on the Earth and Venus.

Janes, Daniel M.↗
NASA NTRS1995

Aerodynamic Evaluation of Two Compact Radial-Inflow Turbine Rotors

The aerodynamic evaluation of two highly loaded compact radial turbine rotors was conducted at the NASA Lewis Research Center Small Engine Component Test Facility (SECTF). The experimental results were used for proof-of-concept, for modeling radial inflow turbine rotors, and for providing data for code verification. Two rotors were designed to have a shorter axial length, up to a 10-percent reduced diameter, a lighter weight, and equal or higher efficiencies with those of conventional radial inflow turbine rotors. Three configurations were tested: rotor 1, having a 40-percent shorter axial length, with the design stator (stator 1); rotor 1 with the design stator vanes closed down (stator 2); and rotor 2, slightly shorter axially and having higher loading, with stator 2. The stator had 36 vanes and the rotors each had 14 solid blades. Although presently uncooled, the rotor blades were designed for thicknesses which would allow cooling passages to be added. The overall stage performance measurements and the rotor and stator exit flow field surveys were obtained. Measurements of steady state temperatures, pressures, mass flow rates, flow angles, and output power were made at various operating conditions. Data were obtained at corrected speeds of 80, 90, 100, 110, and 120 percent of design over a range of equivalent inlet-to-exit pressure ratios of 3.5, 4.0, 4.5, and 5.0, the maximum pressure ratio achieved. The test showed that the configuration of rotor 1 with stator 1 running at the design pressure ratio produced a flow rate which was 5.6 percent higher than expected. This result indicated the need to close down the stator flow area to reduce the flow. The flow area reduction was accomplished by restaggering the vanes. Rotor 1 was retested with the closed-down stator vanes and achieved the correct mass flow. Rotor 2 was tested only with the restaggered vanes. The test results of the three turbine configurations were nearly identical. Although the measured efficiencies of the compact designs fell 2 to 3 points below the predicted efficiency of 91 percent, they did meet and exceed by up to 2.5 percentage points the efficiences of state-of-the-art turbines found in the literature.

Simonyi, P. Susan↗
NASA NTRS1995

Non-radial flow in the solar wind

Although the radial component of the solar wind dominates the solar wind speed, significant non-radial velocity components are also present. These flows are more difficult to measure accurately, but we now have data sets including the east-west (tangential) and north-south (normal) flows from PVO at Venus, IMP 8 at Earth, and Voyagers 1 and 2 from 1 to 45 AU. We compare the non-radial flow observations from these spacecraft. One of the more interesting features is that the north-south flow angle observed at Earth and Venus oscillates with the period of a local (Earth or Venus) year. These oscillations occur throughout two solar cycles in the IMP 8 data set and are very apparent in the PVO data from 1978 to 1986 but less obvious after this. We will report on the origin of this feature. The tangential flow observed by both IMP 8 and Voyager is on average slightly positive (approximately 1.75 km/s). The magnitudes of the nonradial velocity components decrease with distance from the Sun.

Richardson, J. D.↗
NASA NTRS1995

Radial gradients of ion densities and temperatures observed by SWICS/Ulysses

Mean density and temperature gradients of solar wind protons and alpha-particles between 1 and 5.4 AU are established from SWICS/Ulysses observations. All parameters are classified in speed intervals. au order scheme giving us a natural extension of the Helios observations. which were usually classified according to speed of the wind. The radial gradients show a similar behaviour of both particle species, while the particles radially propagate and thereby cool off in the heliosphere. The slow solar wind is found, for protons as well as a particles. to expand adiabatically all the way out to 5.4 AU, while the fast wind evolves non-adiabatically and is heated by interplanetary sources. It, seems that the heating rate of the a-particles is larger than the heating rate of the protons. The ion temperature ratio and density ratio are determined. They do not indicate any radial dependence. The temperature ratio T(sub alpha)/T(sub p) is on average about 4. It has a maximum of 4.5 in the velocity interval where 400 km/s is less than v(sub p) is less than 500 km/s, while in slow wind with v(sub p) is less than 400 km/s it has a minimum value of 37. and for fast wind with v(sub p) is greater than 500 km/s it is 3.9. The density gradients shows compression effects resulting from fast wind overtaking the slow wind.

Liu, S.↗
NASA NTRS1998

An Assessment of the Axial and Radial Dilation of a DPIMS Tantalum Cartridge for Space Shuttle Flight Experiments

Ground-based heat treatment tests are planned on an argon gas-filled tantalum cartridge developed as pan of a Diffusion Processes in Molten Semiconductors (DPIMS) experiment conducted on NASA's Space Shuttle. The possibility that the cartridge may creep during testing and touch the furnace walls is of real concern in this program. The present paper discusses the results of calculations performed to evaluate this possibility. Deformation mechanism maps were constructed using literature data in order to identify the creep mechanism dominant under the appropriate stresses and temperatures corresponding to the test conditions. These results showed that power-law creep was dominant when the grain size of the material exceeded 55 gm but Coble creep was the important mechanism below this value of grain size. Finite element analysis was used to analyze the heat treatment tWs assuming a furnace run away condition (which is a worst case scenario) using the appropriate creep parameters corresponding to grain sizes of 1 and 100 gm. Calculations were also conducted to simulate the effect of an initial 3 tilt of the cartridge assembly, the maximum possible tilt angle. The von Mises stress and su-ain distributions were calculated assuming that the cartridge was fixed at one end as it was heated from ambient temperature to 1823 K in 1.42 h, maintained at 1823 K for 9.5 h and then further heated to an over temperature condition of 2028 K in 0.3 h. The inelastic axial and radial displacements of the cartridge walls were evaluated by resolving the von Mises strain along the corresponding directions. These calculations reveal that the maximum axial and radial displacements are expected to be about 2.9 and 0.25 mm, respectively, for both fine and coarse-grained materials at 2028 K. It was determined that these displacements occur during heat-up to temperature and creep of the cartridge is likely to be relatively insignificant irrespective of grain size. Furthermore, with a 3' tilt of the cartridge, the deflection is increased by only 0.39 gm which is negligible. Since the gap between the furnace heating elements and the cartridge is about 7.5 mm and less than the maximum radial dilation of 0.25 mm at 2028 K, it is concluded that the cartridge is unlikely to touch the furnace walls during the experiments.

Raj, S.V.↗
NASA NTRS1998

Track Structure Model for Radial Distributions of Electron Spectra and Event Spectra from High-Energy Ions

An analytic method is described for evaluating the average radial electron spectrum and the radial and total frequency-event spectrum for high-energy ions. For high-energy ions, indirect events make important contributions to frequency-event spectra. The method used for evaluating indirect events is to fold the radial electron spectrum with measured frequency-event spectrum for photons or electrons. The contribution from direct events is treated using a spatially restricted linear energy transfer (LET). We find that high-energy heavy ions have a significantly reduced frequency-averaged final energy (yF) compared to LET, while relativistic protons have a significantly increased yF and dose-averaged lineal energy (yD) for typical site sizes used in tissue equivalent proportional counters. Such differences represent important factors in evaluating event spectra with laboratory beams, in space- flight, or in atmospheric radiation studies and in validation of radiation transport codes. The inadequacy of LET as descriptor because of deviations in values of physical quantities, such as track width, secondary electron spectrum, and yD for ions of identical LET is also discussed.

Cucinotta, F. A.↗
NASA NTRS1996

1985 Voyager 2 Radio Ranging Measurements of Coronal Density: Asymmetry in the Radial Profiles Explained

An asymmetry in the radial variation of electron density above the cast and west limbs of the Sun was inferred from centimeter wavelength ranging measurements conducted by Voyager 2 during its 1985 solar conjunction. The Voyager 2 ranging measurements, which took place in the heliocentric distance range of 7-40 solar radius, have been compared with the white-light coronagraph measurements of the underlying corona collected by the Mark 3 K-coronameter located at the Mauna Loa Solar Observatory. It is shown that the disparity in radial profiles is not real but is instead caused by longitudinal variations stemming from the probing of significantly different source regions its revealed in the white-light measurements. These results improve our understanding of the probing abilities of ranging measurements and their relationship to white-light measurements. They reinforce the notion that the high-precision and high-sensitivity features of ranging measurements are more fully exploited in the investigation of density variations across the ubiquitous low-contrast raylike structures that permit the corona, rather than in determining radial density profiles.

Woo, Richard↗
NASA NTRS1999

Determination of the Solid/Liquid Interface Shape and Resultant Radial Homogeneity in Directionally Solidified Hg(0.89)Mn(0.11)Te

Directional solidification and interrupted directional solidification experiments were used to determine tile shape of the solid/liquid interface and the resultant radial homogeneity in Hg(0.89)Mg(0.11)Te. For directionally solidified samples solidified at a rate of 0.09 microns/sec in a thermal gradient of 83 C/cm, a maximum of 0.006 molar percent MnTe radial variation across the Hg0.89)Mn(0.11)Te boules at specific locations was determined using an FTIR technique. This FTIR evaluation of the radial homogeneity also indicated an asymmetrical, convex interface shape during solidification. The asymmetrical, convex shape of the growth interface was confirmed by interrupted directional solidification experiments. These were performed under the same growth conditions as the normally completed directional solidification experiments except that the samples were quenched before the final growth transient was reached. In these experiments, etching and scanning X-ray fluorescence were used to reveal the shape of the solid/liquid interface. Microprobe analysis of composition gradients across the interface was used to confirm the authors' previous work in evaluating the segregation coefficient of Hg(0.89)Mn(0.11)Te alloy. Microprobe analysis of the interface region of the interrupted growth sample revealed a dendritic structure containing secondary and tertiary dendritic arms.

Price, M. W.↗
NASA NTRS2001

Multiple Radially Aligned Plasmaspheric Structures as Evidence of Standing Hydromagnetic Waves: IMAGE EUV Observations and Forward Modeling

The IMAGE EUV imager has observed several instances where the outer plasmasphere is populated by multiple radially aligned structures resembling "plasmaspheric fingers". The observation of these plasmaspheric structures suggests the presence of an azimuthal standing hydromagnetic wave mode. Eiganmodes appear to explain finger-like. nearly radial density structures that sometimes divide into two structures with increasing radial distance. The implication is of boundaries at fixed local times, which results in a widening "box" in which standing waves are developed. The structures also suggest a single driving frequency for the source of the waves. We present EUV observations of plasmaspheric fingers observed on August 2000 as well as plasmaspheric modeling of azimuthal wave modes in an effort to quantify the origin of these observed structures

Gallagher, D. L.↗
NASA NTRS2002

Radial Field Piezoelectric Diaphragms

A series of active piezoelectric diaphragms were fabricated and patterned with several geometrically defined Inter-Circulating Electrodes "ICE" and Interdigitated Ring Electrodes "ICE". When a voltage potential is applied to the electrodes, the result is a radially distributed electric field that mechanically strains the piezoceramic along the Z-axis (perpendicular to the applied electric field). Unlike other piezoelectric bender actuators, these Radial Field Diaphragms (RFDs) strain concentrically yet afford high displacements (several times that of the equivalent Unimorph) while maintaining a constant circumference. One of the more intriguing aspects is that the radial strain field reverses itself along the radius of the RFD while the tangential strain remains relatively constant. The result is a Z-deflection that has a conical profile. This paper covers the fabrication and characterization of the 5 cm. (2 in.) diaphragms as a function of poling field strength, ceramic thickness, electrode type and line spacing, as well as the surface topography, the resulting strain field and displacement as a function of applied voltage at low frequencies. The unique features of these RFDs include the ability to be clamped about their perimeter with little or no change in displacement, the environmentally insulated packaging, and a highly repeatable fabrication process that uses commodity materials.

Bryant, R. G.↗