Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “parametric study”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Parametric study of ion heating in a burnout device (HIP-1)

Results of further studies on the Lewis Research Center hot-ion plasma source (HIP-1) are reported. Changes have been made in both the electrode geometry and materials to produce higher ion temperatures. Ion temperature increased significantly with increased vacuum pumping speed. The best ion temperatures achieved, so far, for H(+), D(+), and He(+) plasmas are estimated to be equal to, or greater than 0.6, equal to, or greater than 0.9, and equal to, greater than 2.0 keV, respectively. Electrode pairs produced high ion temperatures whether on the magnetic axis or off it by 5.5 cm. Multiple sources, one on-axis and one off-axis, were run simultaneously from a single power supply by using independent gas feed rates. A momentum analyzer has been added to the charge-exchange neutral particle analyzer to identify particles according to mass, as well as energy. Under any given plasma condition, the higher mass ions have higher average energies but not by as much as the ratio of their respective masses.

Sigman, D. R.↗
NASA NTRS1974

Parametric study of STOL short-haul transport engine cycles and operational techniques to minimize community noise impact

The effect of aircraft operational techniques in the terminal area on community noise impact of future short haul aircraft was investigated. Aircraft equipped with mechanical flap (MF) and aircraft with externally blown flap (EBF) were used to study the noise impact at four U.S. airports. The four airports were: (1) Hanscom Field (Boston), (2) Washington National (D.C.), (3) Midway (Chicago) and (4) Orange County (California). With the exception of Washington National (D.C.), the study showed that a reduction of approximately 40 percent in the number of people highly annoyed can be obtained by using the recommended operational techniques. The evaluation procedures and methodology developed in the study represent an advance in acoustical state-of-the-art and provide an effective and useful tool for determining aircraft noise impact on the airport community.

Source record↗
NASA NTRS1974

Parametric study of near-wake structure of spherical and cylindrical bodies in the laboratory

Some aspects of the interaction between metal bodies and streaming rarefied plasmas were studied in a newly constructed plasma wind tunnel as part of an attempt to investigate (via simulation) phenomena relevant to the spacecraft/space plasma interaction. Detailed near-wake ion current profiles for both spherical and cylindrical bodies at different body potentials and at different plasma flow parameters are presented. Various features of the profiles can be correlated, at least qualitatively, with both plasma and body characteristics. The general importance of body geometry is qualitatively demonstrated. In addition, a discussion of the relevance of the above studies to previous in situ data obtained from the Ariel I and Gemini/Agena missions is given.

Oran, W. A.↗
NASA NTRS1974

Parametric study of STOL short-haul engine cycles and operational techniques to minimize community noise impact

The effect of aircraft operational techniques in the terminal area on community noise impact of future short-haul aircraft was investigated. These operational techniques affected altitude, flap retraction rate, thrust cutback altitude, amount of thrust cutback, and amount of turning. During landing the parameters varied were glide slope angle, change in slope angle (two segment approach), and flap extension rate. One mechanical-flap (MF) aircraft and one externally-blown-flap (EBF) aircraft were used to study by noise impact at four U.S. airports, Hanscom Field (Boston); Washington National; Midway (Chicago); and Orange County (California). With the exception of Washington National (DCA), the study showed that a reduction of approximately 40 percent in the number of people highly annoyed (as defined in the study) can be obtained by using these operational techniques. At DCA the number of people highly annoyed using the standard procedure was quite low, but it is significant that the minimumimpact case for Runway 36 reduced the number of people highly annoyed to zero using a power cutback and a turning departure path. The evaluation procedures and methodology developed in this study represents an advance in acoustical state-of-the-art and should provide an effective and useful tool for determining aircraft noise impact upon the airport community.

Source record↗
NASA NTRS1974

Exhaust emissions of a double annular combustor: Parametric study

A full scale double-annular ram-induction combustor designed for Mach 3.0 cruise operation was tested. Emissions of oxides of nitrogen, carbon monoxide, unburned hydrocarbons, and smoke were measured over a range of combustor operating variables including reference velocity, inlet air temperature and pressure, and exit average temperature. ASTM Jet-A fuel was used for these tests. An equation is provided relating oxides of nitrogen emissions as a function of the combustor, operating variables. A small effect of radial fuel staging on reducing exhaust emissions (which were originally quite low) is demonstrated.

Schultz, D. F.↗
NASA NTRS1975

Experimental parametric studies of transonic T-tail flutter

Wind-tunnel tests of the T-tail of a wide-body jet airplane were made at Mach numbers up to 1.02. The model consisted of a 1/13-size scaled version of the T-tail, fuselage, and inboard wing of the airplane. Two interchangeable T-tails were tested, one with design stiffness for flutter-clearance studies and one with reduced stiffness for flutter-trend studies. Transonic antisymmetric-flutter boundaries were determined for the models with variations in: (1) fin-spar stiffness, (2) stabilizer dihedral angle (-5 deg and 0 deg), (3) wing and forward-fuselage shape, and (4) nose shape of the fin-stabilizer juncture. A transonic symmetric-flutter boundary and flutter trends were established for variations in stabilizer pitch stiffness. Photographs of the test configurations are shown.

Ruhlin, C. L.↗
NASA NTRS1975

A parametric study of the value of hydrological information for irrigation and hydropower management of the Feather River

A case study analysis is presented of the relationships between improvements in the accuracy, frequency, and timeliness of information used in making hydrological forecasts and economic benefits in the areas of hydropower and irrigation. The area chosen for the case study is the Oroville Dam and Reservoir. Emphasis is placed on the use of timely and accurate mapping of the aerial extent of snow in the basin by earth resources survey systems such as LANDSAT. The subject of benefits resulting from improved runoff forecasts is treated in a generalized way without specifying the source of the improvements.

Wetzler, E.↗
NASA NTRS1976

Parametric study of the noise produced by the interaction of the main rotor wake with the tail rotor

A model was designed, fabricated and wind tunnel tested to identify some of the parameters which were pertinent to the noise produced by the interaction of the main rotor wake with the tail rotor. The model provided for variations in many geometric and operating parameters. The initial set of tests indicated that the noise produced by the tail rotor was, in general, sensitive to the location of the vortex interaction on the tail rotor disk, direction of rotation, lateral rotor fin spacing, tip speed and the operating mode of the tail rotor; and generally insensitive to main rotor thrust coefficient, longitudinal spacing and tail rotor to main rotor rotational speed ratios. Refinements in the analyses to adequately predict the noise phenomenon have been outlined to complement further experimental investigations.

Balcerak, J. C.↗
NASA NTRS1976

Theoretical optimization and parametric study of n-on-p Al/x/Ga/1-x/As-GaAs graded band-gap solar cell

A comprehensive theoretical model of the graded band-gap Al(x)Ga(1-x)As-GaAs solar cell is used to optimize the n-on-p cell. The model includes power losses due to surface, bulk, and junction minority-carrier recombination, series resistance, and photon reflection from an SiO antireflection coating of optimum thickness. The optimized cell has a junction depth/graded band-gap layer thickness of 1.0 micron, respective donor and acceptor concentrations of 4 x 10 to the 17th power and 2 x 10 to the 17th power per cu cm, and a surface AlAs mode fraction of x = 0.35. The optimized graded band-gap cell has an air-mass-zero efficiency of 17.7% (not corrected for a 13% front surface contact area) and is shown to be less sensitive than a similar n-on-p GaAs cell to material degradation in the form of decreased minority-carrier diffusion lengths and increased surface-recombination velocity

Hutchby, J. A.↗
NASA NTRS1977

Theoretical Parametric Study of the Relative Advantages of Winglets and Wing-Tip Extensions

This study provides sweeping confirmation, for a wide range of wings, of the recommendations of Whitcomb in NASA TN D-8560. For identical increases in bending moment, a winglet provides a greater gain in induced efficiency than tip extension. Winglet toe angle allows design trades between efficiency and root moment. A winglet shows the greatest benefit when the wing loads are heavy near the tip. Washout diminishes the benefit of either tip modification, and the gain in induced efficiency becomes a function of lift coefficient; thus, heavy wing loadings obtain the greatest benefit from a winglet, and low-speed performance is enhanced even more than cruise performance. Both induced efficiency and bending moment increase with winglet length and outward cant. The benefit of a winglet relative to a tip extension is greatest for a nearly vertical winglet. Root bending moment is proportional to the minimum weight of bending material required in the wing; thus, it is a valid index of the impact of tip modifications on a new wing design.

Aerodynamics↗
NASA NTRS1977

Parametric study of transport aircraft systems cost and weight

The results of a NASA study to develop production cost estimating relationships (CERs) and weight estimating relationships (WERs) for commercial and military transport aircraft at the system level are presented. The systems considered correspond to the standard weight groups defined in Military Standard 1374 and are listed. These systems make up a complete aircraft exclusive of engines. The CER for each system (or CERs in several cases) utilize weight as the key parameter. Weights may be determined from detailed weight statements, if available, or by using the WERs developed, which are based on technical and performance characteristics generally available during preliminary design. The CERs that were developed provide a very useful tool for making preliminary estimates of the production cost of an aircraft. Likewise, the WERs provide a very useful tool for making preliminary estimates of the weight of aircraft based on conceptual design information.

Beltramo, M. N.↗
NASA NTRS1977

Theoretical parametric study of the relative advantages of winglets and wing-tip extensions

It was found that for identical increases in bending moment, a winglet provides a greater gain in induced efficiency than a tip extension. Winglet toe-in angle allows design trades between efficiency and root moment. A winglet showed the greatest benefit when the wing loads were heavy near the tip. Washout diminished the benefit of either tip modification, and the gain in induced efficiency became a function of lift coefficient; heavy wing loadings obtained the greatest benefit from a winglet, and low speed performance was enhanced even more than cruise performance. Both induced efficiency and bending moment increased with winglet length and outward cant. The benefit of a winglet relative to a tip extension was greatest for a nearly vertical winglet. Root bending moment was proportional to the minimum weight of bending material required in the wing; it is a valid index of the impact of tip modifications on a new wing design.

Heyson, H. H.↗
NASA NTRS1977

Parametric study of ascent performance of a vertically launched hydrogen-fueled single-stage reusable transport

Ascent performance characteristics were studied for a vertical-take-off, horizontal-landing, single-stage-to-orbit transport vehicle powered by hydrogen fuel rocket with a mixture of fixed- and dual-position nozzles. The analysis was made by systematically varying two sets of trajectory similarity parameters based on the propulsive and aerodynamic characteristics of the vehicle and by calculating a trajectory for each combination of the parameters. The propulsion parameters were the initial thrust-weight ratio, engine combination, and the two expansion ratios of the dual-position rocket nozzles. The aerodynamic parameters were the ratio of reference area to initial weight and the ratio of maximum allowable normal force to initial weight. A first-order analysis was carried out to determine the effect on the performance of including the engine mass penalty. This analysis indicates that the configuration with the lowest initial mass for a given payload requires all dual-position nozzles with initial expansion ratio of 50 and a final expansion ratio of 150.

Rehder, J. J.↗
NASA NTRS1977

Parametric studies of North East Corridor rail passenger service between New York City and Washington, D. C.

Speed profiles of rail passenger service between New York City and Washington, D.C. were developed and showed progressively fewer speed restrictions and increasing maximum speeds. The significant equipment characteristics include the portion of the total weight on driven axles, i.e., multiple unit (MU) cars versus locomotive hauled trains, and the short term tractive effort rating of the motors. The ratio of acceleration plus braking time to total time is provided for validation of the use of the short term propulsion equipment ratings. Absolute trip times are shown to be determined primarily by the allowed speed profile. Locomotive hauled train weights and lengths and the locomotive capabilities and characteristics that are required to make the performance of this type of train comparable to that of MU trains are given.

Stallkamp, J. A.↗
NASA NTRS1978

Parametric study of large-scale eddy properties. II - The zonal scale

The paper studies the average zonal wavenumber in relation to theoretical and experimental consideration not taken into account by Srivatsangam (1976b). A result of the laboratory experiments with rotating cylindrical annuli is the inverse relationship between the horizontal temperature gradient and the azimuthal wavenumber. Such a relationship is sought in the atmosphere in order to delineate in which belt, if anywhere, there is a similarity between the atmosphere and the laboratory experiments. Linear baroclinic theory reveals the existence of a functional dependence between the zonal wavelength of the most rapidly amplifying waves and the static stability. Results pertaining to the dependence of the average zonal wavenumber on the meridional temperature gradient along with results on the correlation between the average zonal wavenumber and static stability are presented.

Srivatsangam, S.↗
NASA NTRS1978

Parametric study of two planar high power flexible solar array concepts

The design parameters examined were: frequency, aspect ratio, packaging constraints, and array blanket flatness. Specific power-to-mass ratios for both solar arrays as a function of array frequency and array width were developed and plotted. Summaries of the baseline design data, developed equations, the computer program operation, plots of the parameters, and the process for using the information as a design manual are presented.

Garba, J. A.↗
NASA NTRS1980

Parametric study of helicopter aircraft systems costs and weights

Weight estimating relationships (WERs) and recurring production cost estimating relationships (CERs) were developed for helicopters at the system level. The WERs estimate system level weight based on performance or design characteristics which are available during concept formulation or the preliminary design phase. The CER (or CERs in some cases) for each system utilize weight (either actual or estimated using the appropriate WER) and production quantity as the key parameters.

Beltramo, M. N.↗