Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “paraffin”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

228 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

Phase Change Material Heat Sink for an ISS Flight Experiment

A flight experiment is being constructed to utilize the persistent microgravity environment of the International Space Station (ISS) to prove out operation of a microgravity compatible phase change material (PCM) heat sink. A PCM heat sink can help to reduce the overall mass and volume of future exploration spacecraft thermal control systems (TCS). The program is characterizing a new PCM heat sink that incorporates a novel phase management approach to prevent high pressures and structural deformation that often occur with PCM heat sinks undergoing cyclic operation in microgravity. The PCM unit was made using brazed aluminum construction with paraffin wax as the fusible material. It is designed to be installed into a propylene glycol and water cooling loop, with scaling consistent with the conceptual designs for the Orion Multipurpose Crew Vehicle. This paper reports on the construction of the PCM heat sink and on initial ground test results conducted at UTC Aerospace Systems prior to delivery to NASA. The prototype will be tested later on the ground and in orbit via a self‐contained experiment package developed by NASA Johnson Space Center to operate in an ISS EXPRESS rack.

Quinn, Gregory↗
NASA NTRS2014

An Innovative Aperture Cover Mechanism Used on SDO/EVE and MMS/SDP

This paper describes an aperture cover mechanism that was successfully flown in four locations on SDO/EVE, and is awaiting launch in sixteen locations on MMS. This design uses a paraffin actuator and a latch that secures the cover closed and removes the actuator from the load path. This latch allows the assembly to operate both as a light weight contamination cover (SDO/EVE), and also as a high-strength sensor restraint mechanism (MMS/SDP). The paper provides design/analysis/test information about the mechanism.

Steg, Stephen↗
NASA NTRS2018

Fuel Sensitivity of Gas Emissions, Lean Blowout and Combustion Dynamics for a 9-Point LDI Combustor

Fuel sensitivity of gaseous emissions, approach to lean blowout and combustion dynamics are evaluated in this study. Experiments were conducted at the NASA Glenn Research Center's CE-5 flame tube test facility with a 9-point Swirl-Venturi Lean Direct Injection (SV-LDI) combustor. A reference jet fuel (A2) and two test fuels (C1 and C3) from were provided by the National Jet Fuels Combustion Program (NJFCP). C1 is essentially a 2-component iso-paraffin test fuel with a low cetane number of 17, and C3 is a high viscosity test fuel. Approach to lean blowout was monitored in terms of the rapid increase in CO emissions index as equivalence ratio decreased, but testing did not proceed all the way to lean blowout (LBO). Burning C1 was found to produce lower NOx emissions, but C1 flame temperatures were about 25 K higher relative to A2 at near LBO points (where CO emissions increased very rapidly). The NOx emissions of C3 were similar to A2. At low power conditions where fuel injector performance is not optimized for this 9-point LDI combustor, C3 had higher CO emissions than A2 and C1, likely due to C3's higher viscosity relative to A2 and C1. No discernable difference in combustion dynamics was observed between the three fuels tested in the 9-point LDI combustor. While a systematic ignition test campaign was not conducted, it was observed that C1 required a higher equivalence ratio and inlet air temperature for test rig ignition compared to A2 and C3.

Lean Direct Injection↗
NASA NTRS2018

Outgas and Vacuum Storage Testing for MAV Hybrid Fuel Grain

As a part of the Mars Ascent Vehicle mission, NASA MSFC has formulated a new hybrid fuel grain from a paraffin blend, named SP-7. As a part of the necessary preparation for the mission, this material must be tested for any outgassing behavior or other property changes due to vacuum exposure. This type of testing had not yet been conducted for this material. The goal of this project was to set up and begin automated analysis of this material, which would then run over the course of a year. To accomplish this goal, a few primary objectives were necessary-construction of a vacuum chamber to house the test, implementation of an automated gas analyzer system, preparation of SP-7 samples, and test initialization.

Mars Ascent Vehicle↗
NASA NTRS2018

Fuel Sensitivity of Gas Emissions, Lean Blowout and Combustion Dynamics for a 9-Point LDI Combustor

Fuel sensitivity of gaseous emissions, approach to lean blowout and combustion dynamics are evaluated in this study. Experiments were conducted at the NASA Glenn Research Center's CE-5 flame tube test facility with a 9-point Swirl-Venturi Lean Direct Injection (SV-LDI) combustor. A reference jet fuel (A2) and two test fuels (C1 and C3) from were provided by the National Jet Fuels Combustion Program (NJFCP). C1 is essentially a 2-component iso-paraffin test fuel with a low cetane number of 17, and C3 is a high viscosity test fuel. Approach to lean blowout was monitored in terms of the rapid increase in CO emissions index as equivalence ratio decreased, but testing did not proceed all the way to lean blowout (LBO). Burning C1 was found to produce lower NOx emissions, but C1 flame temperatures were about 25 K higher relative to A2 at near LBO points (where CO emissions increased very rapidly). The NOx emissions of C3 were similar to A2. At low power conditions where fuel injector performance is not optimized for this 9-point LDI combustor, C3 had higher CO emissions than A2 and C1, likely due to C3's higher viscosity relative to A2 and C1. No discernable difference in combustion dynamics was observed between the three fuels tested in the 9-point LDI combustor. While a systematic ignition test campaign was not conducted, it was observed that C1 required a higher equivalence ratio and inlet air temperature for test rig ignition compared to A2 and C3.

Combustion dynamics↗
NASA NTRSDate not supplied

Lean Blowout (LBO) Simulations in a Rich-Burn Quick-Quench Lean-Burn (RQL) Gas Turbine Combustor

The transient processes involving lean blowout (LBO) in a RQL combustor such as the single cup combustor in the National Jet Fuels Combustion Program (NJFCP) referee rig are simulated with the reduced mechanisms based on Hybrid Chemistry for two different fuels, Cat-A2 and Cat-C1. Cat-A2 fuel is Jet-A with average or nominal properties based on a survey of the Petroleum Quality Information System database. The Cat-C1, an alternative jet fuel, is a GEVO alcohol-to-jet (ATJ) fuel composed almost entirely of two highly-branched C12 and C16 iso-paraffins. Experiments conducted in the NJFCP referee rig established a stable flame at an equivalence ratio of 0.096 (the near LBO condition) as the starting condition for LBO tests performed with all Category A and C fuels. Simulations of the approach to LBO verify that a stable flame is established at the near-LBO condition for each fuel before reducing fuel flow rate (and thus equivalence ratio) in a step-wise manner. At each new equivalence ratio, the global heat release rate and total fuel evaporation time histories are monitored to verify a new stable flame condition has been established before performing the next reduction in equivalence ratio until the flame is approaching the blowout. Main conclusions are threefold: (1) For Cat-C1 fuel the equivalence ratio for LBO is around 0.087. (2) For Cat-A2 fuel the equivalence ratio for LBO is either 0.082 or 0.078 depended on the time span of equivalence ratio of 0.085. (3) The averaged difference from LES on LBO for Cat-C1 relative to Cat-A2 is 8.75% versus 7.8% from the experimental data.

LES, Lean blow out↗
NASA NTRSDate not supplied

CFD Evaluation of Aviation Fuels for Commercial Supersonics Technology

An overview is provided of a CFD analysis of a Lean-Direct Injection (LDI) combustion concept for NASA’s Commercial Supersonic Transport (CST) program. The National Combustion Code (OpenNCC) was used to perform two-phase reacting flow computations with three different aviation fuels for UTRC’s Axially Controlled Stoichiometry (ACS) combustor at CST cruise conditions. All computations were performed with a consistent approach of mesh-generation, spray and chemical-kinetics modeling for the combustor. Emissions (EICO, EINOx) and performance characteristics were predicted with OpenNCC, to evaluate the impact of replacing Jet-A with RP2 and Iso-Paraffinic Kerosene (IPK) for supersonic combustor applications. The CFD predictions of flame structure for IPK fuel were significantly different in comparison to those of Jet-A and RP2 fuel. However, the CFD analysis predicted very similar EINOx emissions for Jet-A, RP-2 and IPK fuels. The predicted EINOx emissions for all three fuels also compared very well with measured experimental data.

gas turbine combustion↗
NASA NTRSDate not supplied

Impact of Simulated Galactic Cosmic Radiation and Hindlimb Unloading on the Mouse Adrenal Gland Morphology and Histology

Stress related impact of Galactic Cosmic Radiation (GCR) combined with microgravity in space are concerns for astronauts going beyond the Van Allen belts on their way to the Moon and Mars. The adrenal gland is the central endocrine tissue involved in stress management, adrenal hormones regulate the immune system, cellular and tissue metabolism, and glucose and sodium balances. Adult (6 m old) female (n=18) and male (n=18) C57BL/6J mice were divided evenly into 6 treatment groups (control, hindlimb unloading (HU), irradiated (IR), HU+IR, group house control, and group house IR). Adrenals were dissected and fixed for 24 h in 4% paraformaldehyde, followed by transfer to 70% EtOH, and shipment to KUMC. Adrenals were then embedded in paraffin and serial sectioned and 4 central sections from each were stained with H&E, prior to imaging on a Nikon 80i microscope. Whole adrenal cross section area, medullary area, and cortex area were determined. General adrenal gland morphology and histology did not appear to be affected by hindlimb unloading or GCR exposure. Total cross-sectional area, medullary region, and cortex of the adrenal were not different across treatment groups. Male adrenal cross-sectional areas are half the size of the female adrenals, due to a difference in cortex area. In conclusion, simulated microgravity and GCR did not dramatically affect the adrenal gland histology or size. Support from Accelerate Cancer Education Internship Program (KUCC) and KINBRE Summer Scholars Program (KUMC) and NASA Human Research Program (HRP) Human Factors Behavioral Performance Element Grant 18 18FLAG 2 0028

radiation↗
NASA NTRS2015

Solar Probe Plus MAG Sensor Thermal Design for Low Heater Power and Extreme Thermal Environment

The heater power available for the Solar Probe Plus FIELDS MAG sensor is less than half of the heritage value for other missions. Nominally the MAG sensors are in the spacecraft's umbra. In the worst hot case, approximately 200 spacecraft communication downlinks, up to 10 hours each, are required at 0.7 AU. These downlinks require the spacecraft to slew 45 deg. about the Y-axis, exposing the MAG sensors and boom to sunlight. This paper presents the thermal design to meet the MAG sensor thermal requirements in the extreme thermal environment and with low heater power. A thermal balance test on the MAG sensor engineering model has verified the thermal design and correlated the thermal model for flight temperature predictions.

Thermal design↗