Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “neutron diffraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Real-Time In Situ Neutron Diffraction Investigation of Phase-Specific Load Sharing in a Cold-Rolled TRIP Sheet Steel

Real-time in situ neutron diffraction was used to investigate the loading-direction dependence of phase-specific load sharing in a cold-rolled TRIP 780 sheet steel under tension at room temperature. A slightly lower yield stress and relatively faster initial strain hardening were observed for the tension along the rolling direction (RD), than those along the transverse direction (TD) and the diagonal direction (DD). In all three loading directions, the redistribution of inter-phase and inter-granular load sharing occurs upon the yields of the BCC matrix and the FCC phase. The FCC phase is found to yield earlier along the RD than those along the TD and DD. Based on the Hooke’s law and the rule of mixture, it is found that the lattice strains of BCC-(211)/FCC-(311) reflections via single peak fit are better representative of phase elastic strains than the strains calculated via the lattice parameters by Rietveld refinement. The quantitative evolution of phase-specific stress indicates a rapid strain hardening in the FCC phase after yielding during the RD tension. Possible mechanisms of the direction-dependent phase-specific load sharing are discussed in association with the different initial textures in the RD, DD and TD.

Yu, Dunji↗
DOE OSTI2020

Imaging Based Detector with Efficient Scintillators for Neutron Diffraction Measurements

The Anger Camera developed by the detector group at the Oak Ridge National Laboratory was utilized for the present work for its unique advantage of employing multiple modules to obtain large active measurement area for detecting diffracted/scattered thermal neutrons. Considering the relatively small flux associated with diffracted/scattered neutrons, suitable efficiency with high spatial resolution is a requirement for utilizing two-dimensional imaging detectors. The potential to implement pulse shape (in addition to pulse height) discrimination-based scintillators further enhances the ability to detect diffracted neutrons with improved signal to noise ratio. In this paper, initial results associated with 6Li glass-based scintillator will be presented. The authors explored the feasibility of using this system to detect and quantify diffraction peaks and peak shifts at the Neutron Residual Stress Facility (NRSF2), High Flux Isotope Reactor (HFIR) in the Oak Ridge National Laboratory (ORNL). Suitable camera mounting and shielding had to be developed. Reference measurements using polycrystalline powders with known atomic planar spacing will be discussed along with measurement settings associated with expected resolution for peak shift measurements. Initial results are promising and demonstrate that a suitable scintillation-based neutron detecting system is viable for residual stress-based diffraction measurements. Small area detectors are also feasible with suitable consideration to scattering volume and distance to detector.

Seals, Matthew↗
DOE OSTI2018

Non-destructive compositional and microstructural characterization of Sardinian Bronze Age swords through Neutron Diffraction

Highlights: • Determination of the manufacturing technique of some “Sa Idda” swords • New data on their provenience • Determination of: alloy composition, dendritic segregation, mineralization phase - Abstract: The Monte Sa Idda type swords belong to a well characterized typological class, whose origin has long been debated and seems to coincide with the Iberian Peninsula. The name comes from the site of the first discovery of a hoard containing this type of swords, among other bronze artefacts, namely Monte Sa Idda, Decimoputzu-Cagliari, Italy. The swords were produced through fusion inside a casting mould. Such kind of casting mould has not been found in Sardinia, and this may suggests that finished objects were either imported or made using clay or sand casting mould. Moreover, the discovery of these types of sword, in hoards and in votive deposits, raises the problem of their functional use. It is unknown if the blades were intended to be used as weapons, and therefore subjected to cold working necessary for thinning and sharpening of the blade, or as ceremonial objects. In order to answer to these questions, a neutron diffraction experiment was performed on three swords belonging to the Monte Sa Idda type. The results obtained are presented and discussed in the paper.

36 MATERIALS SCIENCE↗
DOE OSTI2021

H-Atom Assignment and Sb–O Bonding of [Mes 3 SbOH][O 3 SPh] Confirmed by Neutron Diffraction, Multipole Modeling, and Hirshfeld Atom Refinement

Neutron wavelength-resolved Laue diffraction experiments permit accurate refinement of the H-atom positions and anisotropic displacement parameters of [Mes 3 SbOH][O 3 SPh]. A multipole-based charge density refinement and a topological analysis of the refined electron density were also performed. Hirshfeld atom refinement (HAR) recovers the neutron-determined H-atom parameters, and the quantum-mechanical electron density used in HAR recovers the electron density topology from the refined multipole model. We report these results confirm that [Mes 3 SbOH][O 3 SPh] does indeed feature a hydroxystibonium cation with a nominal Sb–O single bond and not a stibine oxide with an Sb=O/Sb + –O – bond.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2016

Transformation-induced plasticity in bulk metallic glass composites evidenced by in-situ neutron diffraction

Transformation-induced plasticity in a strain-softening amorphous matrix consisting of austenite B2 phase was studied by in-situ neutron diffraction, coupled with molecular dynamic simulation. It was found that the martensitic transformation from B2 to B19' upon loading commenced at the macroscopic yielding which increased with the decrease of the fraction of the parent austenite B2 phase, and the threshold lattice strain for the martensitic transformation is almost the same in different samples, suggesting that the martensitic transformation in the current glassy matrix is strain-controlled. Analysis of load partition and strain accommodation unveiled that B2 has elastic anisotropy, and the desirable elastic match between B2 and the amorphous matrix ensures a good cooperative deformation. Additionally, molecular dynamic simulation revealed that atoms at the interface between B2 and the amorphous matrix deviated from the standard B2 lattices and acted as nucleation site for the martensitic transformation, eventually giving rise to the strain-controlled martensitic transformation. Our findings provide new insights into the mechanism of phase transformation-mediated plasticity at the microscopic level, and have useful implications for developing novel, high-performance bulk metallic glass composites.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Advancing neutron diffraction for accurate structural measurement of light elements at megabar pressures

Over the last 60 years, the diamond anvil cell (DAC) has emerged as the tool of choice in high pressure science because materials can be studied at megabar pressures using X-ray and spectroscopic probes. In contrast, the pressure range for neutron diffraction has been limited due to low neutron flux even at the strongest sources and the resulting large sample sizes. Here, we introduce a neutron DAC that enables break-out of the previously limited pressure range. Key elements are ball-bearing guides for improved mechanical stability, gem-quality synthetic diamonds with novel anvil support and improved in-seat collimation. We demonstrate a pressure record of 1.15 Mbar and crystallographic analysis at 1 Mbar on the example of nickel. Additionally, insights into the phase behavior of graphite to 0.5 Mbar are described. These technical and analytical developments will further allow structural studies on low-Z materials that are difficult to characterize by X-rays.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2019

Comprehensive study of the magnetic phase transitions in Tb 3 Co combining thermal, magnetic and neutron diffraction measurements

A comprehensive study of the magnetic phase transitions in Tb 3 Co has been undertaken combining different techniques. Using single crystal neutron diffraction in the paramagnetic state a weak crystal structure distortion from the room temperature orthorhombic structure of the Fe 3 C type described with the Pnma space group toward structure with lower symmetry has been observed with cooling below 100 K. At 81 K there is a second order phase transition to an antiferromagnetic incommensurate phase with the propagation vector k = (0.155, 0, 0). As derived from thermal diffusivity measurements, the critical exponents for this transition are very close to the 3D-Heisenberg universality class, proving that the magnetic interactions are short-range but with a deviation from perfect isotropy due to crystal field effects. At T 2 ≈ 70 K there is another magnetic phase transition to a ferromagnetic state whose character is shown to be weakly first order. The low temperature magnetic state has a non-coplanar ferromagnetic structure with strong ferromagnetic components of Tb magnetic moments along the crystallographic c-axis. The application of an external magnetic field B = 2 T along the crystallographic c-axis suppresses the incommensurate antiferromagnetic phase and gives rise to the ferromagnetic phase. The magnetic entropy peak change as well as the refrigerant capacity indicate that Tb 3 Co is a competitive magnetocaloric material in this temperature range.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2026

Uncovering hidden bias in neutron diffraction residual strain measurements

When calculating residual strain via neutron or X-ray diffraction, uncertainties propagated from the peak fit are often inadequate to describe the true scatter of measurements about a singular strain state, such as one that should describe a macroscopic continuum. Because diffraction is inherently a selective process, orientation-dependent scatter arises from the sub-sampling of strong microstructure and strain gradients. This paper investigates the appropriateness of propagated uncertainties with reference to their original intention, i.e. noise about a mean value. Thirty-six unique orientations of strain measurements are taken at multiple locations within an additive friction-stir deposition component with fine-scale gradients (∼200 µm) of plastic strain, texture and residual elastic strain. Multiple strain and stress calculation pathways are compared: direct substitution of three measurements into Hooke's law, direct inversion of any six unique orientations into the strain state tensor and thirty-six measurement least-squares estimation. For the last two cases, the appropriateness of the uncertainty interval is statistically evaluated on the basis of a physical constraint: common agreement under the strain transformation law. For this sample, the direct inversion of six measurements retains a conservative estimate of the uncertainty. However, propagated uncertainties in the least-squares solution greatly underestimate the true experimental scatter. A simple pathway to estimate appropriate uncertainty intervals is suggested. These results demonstrate that the interpretation of uncertainty in residual strain is strongly dependent on intrinsic sample-dependent effects, and that oversampling orientations and statistical analysis can give more accurate results with realistic uncertainties.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Determination of Stress-Free Lattice Spacing (D₀) for Residual Stress Relaxation Measurement in Ni-based Superalloys by Neutron Diffraction

The residual stress and its relaxation in critical engineering components are key to structural materials reliability. The determination of residual stress in bulk engineering structures like Ni-based superalloys can be conducted by measuring the lattice strain with penetrating neutron diffraction. The state-of-the-art engineering diffraction beamline VULCAN at the Oak Ridge National Laboratory (ORNL) Spallation Neutron Source (SNS) provides the critical capability to evaluate the residual strain/stress relaxation in engineering component thanks to the high flux and event data features. By the means of residual stress/strain calculation, it is critical to accurately determine the stress-free lattice spacing d₀, which can be altered by the change of chemistry, unrelieved stress, and measurement scheme. Here we reported d₀ determination for determining residual stress relaxation and distribution in Alloy 718 superalloys after different quenching treatments. Selection of locations for d₀ measurement was discussed by considering the neutron path, attenuation and sample alignment. A dynamic d₀ that resulted from atom diffusion and chemistry change was estimated as function of time for the in-situ relaxation characterization. It demonstrated how the dynamic d₀ values may influence on the strain calculation in different thermally treated samples. The results highlight the importance of dynamic d₀ for in-situ relaxation involving chemical changes and provide guidance to the dynamic d₀ measurement and simulation.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Neutron diffraction studies of a four-coordinated hydride in near square-planar geometry

The structure of a nanospheric polyhydrido copper cluster, [Cu 20 (H) 11 {S 2 P(O i Pr) 2 } 9 ], was determined by single-crystal neutron diffraction. Cu 20 cluster consists of an elongated triangular orthobicupola constructed from 18 Cu atoms that encapsulate a [Cu 2 H 5 } 3- ion in the center with an exceptionally short Cu-Cu distance. The eleven hydrides in the cluster display three different coordination modes to the Cu atoms: Six μ 3 -hydrides in pyramidal geometry, two μ 4 -hydrides in tetrahedral cavity, and three μ 4 -hydrides in an unprecedented near square-planar geometry. The neutron data set was collected on a small crystal of the size 0.20 mm x 0.50 mm x 0.65 mm for seven days using the Spallation Neutron Source TOPAZ single-crystal time-of-flight Laue diffractometer at the Oak Ridge National Laboratory. Furthermore, the final R-factor is 8.64% for 16014 reflections.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2014

Extracting grain-orientation-dependent data from in situ time-of-flight neutron diffraction. I. Inverse pole figures

The problem of calculating the inverse pole figure (IPF) is analyzed from the perspective of the application of time-of flight neutron diffraction to in situ monitoring of the thermomechanical behavior of engineering materials. On the basis of a quasi-Monte Carlo (QMC) method, a consistent set of grain orientations is generated and used to compute the weighting factors for IPF normalization. The weighting factors are instrument dependent and were calculated for the engineering materials diffractometer VULCAN (Spallation Neutron Source, Oak Ridge National Laboratory). The QMC method is applied to face-centered cubic structures and can be easily extended to other crystallographic symmetries. Examples include 316LN stainless steel in situ loaded in tension at room temperature and an Al–2%Mg alloy, substantially deformed by cold rolling and in situ annealed up to 653 K.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2014

High-pressure cell for neutron diffraction with in situ pressure control at cryogenic temperatures

Pressure generation at cryogenic temperatures presents a problem for a wide array of experimental techniques, particularly neutron studies due to the volume of sample required. We present a novel, compact pressure cell with a large sample volume in which load is generated by a bellow. Using a supply of helium gas up to a pressure of 350 bar, a load of up to 78 kN is generated with leak-free operation. In addition, special fiber ports added to the cryogenic center stick allow for in situ pressure determination using the ruby pressure standard. Mechanical stability was assessed using finite element analysis and the dimensions of the cell have been optimized for use with standard cryogenic equipment. Load testing and on-line experiments using NaCl and BiNiO{sub 3} have been done at the WISH instrument of the ISIS pulsed neutron source to verify performance.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2016

Chemical disorder determines the deviation of the Slater–Pauling rule for Fe 2 MnSi-based Heusler alloys: evidences from neutron diffraction and density functional theory

Fe 2 MnSi fails to follow the Slater–Pauling rule. This phenomenon is thought to originate from either: (i) an antiferromagnetic arrangement of Mn ions at low temperature and/or (ii) chemical disorder. An important insight on this issue could be achieved by considering Fe 2 MnSi 1-x Ga x compounds, thoroughly studied here by means of magnetization, neutron diffraction and density functional calculations (DFT). Our results indicate that chemical disorder (and not the antiferromagnetic arrangement) is responsible for the deviation of the Slater–Pauling rule on Fe 2 MnSi-based Heusler alloys. Furthermore, evidences suggest that Ga substitution into Si site favors the Fe/Mn disorder, further enhancing the observed deviation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2014

Polymorphism in Photoluminescent KNdW2O8: Synthesis, Neutron Diffraction, and Raman Study

Polymorphs of KNdW2O8 ( -KNdW2O8 and -KNdW2O8) phosphors were synthesized by an efficient solution combustion technique for the first time. The crystal structure of the polymorphs analyzed from Rietveld refinement of neutron diffraction data confirms that -KNdW2O8 crystallizes in the tetragonal system (space group I4 ), and -KNdW2O8 crystallizes in the monoclinic system (space group C2/m). The local structure of both polymorphs was elucidated using combined neutron pair distribution function (PDF) and Raman scattering techniques. Photoluminescence measurements of the polymorphs showed broadened emission line width and increased intensity for -KNdW2O8 in the visible region compared to -KNdW2O8. This phenomenon is attributed to the increased distortion in the coordination environment of the luminescing Nd3+ ion. Combined PDF, Rietveld, and Raman measurements reveal distortions of the WO6 octahedra and NdO8 polyhedra in -KNdW2O8. This crystal structure photoluminescence study suggests that this class of tungstates can be exploited for visible light emitting devices by tuning the crystal symmetry.

Swain, Diptikanta↗
DOE OSTI2018

Time and frequency dependent mechanical properties of LaCoO 3 -based perovskites: Neutron diffraction and domain mobility

The study of domain wall movement and texture formation in ferroelastic LaCoO 3 perovskite under constant applied compressive stress has been performed using in situ neutron diffraction. Additionally, it was established that under constant applied compressive stress the domain walls show mobility that may lead both to the shrinkage (creep strain) and to the expansion (negative creep strain) of LaCoO 3 perovskite. The domain wall movement and texture formation can be explained by the availability, mobility, and interaction of twins, stacking faults, antiphase boundaries, dislocations, and point defects, such as oxygen vacancies and their complexes as well as impurity atoms. Lastly, the equation of motion was used to describe the possible mechanisms of domain wall movement under applied stress, and it was determined that the available solutions of this equation allow both for the shrinkage (creep strain) and for the expansion (negative creep strain) of LaCoO 3 perovskite to occur.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Crystallization of a fungal lytic polysaccharide monooxygenase expressed from glycoengineered Pichia pastoris for X-ray and neutron diffraction

Lytic polysaccharide monooxygenases (LPMOs) are carbohydrate-disrupting enzymes secreted by bacteria and fungi that break glycosidic bonds via an oxidative mechanism. Fungal LPMOs typically act on cellulose and can enhance the efficiency of cellulose-hydrolyzing enzymes that release soluble sugars for bioethanol production or other industrial uses. The enzyme PMO-2 from Neurospora crassa ( Nc PMO-2) was heterologously expressed in Pichia pastoris to facilitate crystallographic studies of the fungal LPMO mechanism. Diffraction resolution and crystal morphology were improved by expressing Nc PMO-2 from a glycoengineered strain of P. pastoris and by the use of crystal seeding methods, respectively. These improvements resulted in high-resolution (1.20 Å) X-ray diffraction data collection at 100 K and the production of a large Nc PMO-2 crystal suitable for room-temperature neutron diffraction data collection to 2.12 Å resolution.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2014

Six-axis multi-anvil press for high-pressure, high-temperature neutron diffraction experiments

We developed a six-axis multi-anvil press, ATSUHIME, for high-pressure and high-temperature in situ time-of-flight neutron powder diffraction experiments. The press has six orthogonally oriented hydraulic rams that operate individually to compress a cubic sample assembly. Experiments indicate that the press can generate pressures up to 9.3 GPa and temperatures up to 2000 K using a 6-6-type cell assembly, with available sample volume of about 50 mm{sup 3}. Using a 6-8-type cell assembly, the available conditions expand to 16 GPa and 1273 K. Because the six-axis press has no guide blocks, there is sufficient space around the sample to use the aperture for diffraction and place an incident slit, radial collimators, and a neutron imaging camera close to the sample. Combination of the six-axis press and the collimation devices realized high-quality diffraction pattern with no contamination from the heater or the sample container surrounding the sample. This press constitutes a new tool for using neutron diffraction to study the structures of crystals and liquids under high pressures and temperatures.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗