Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “molten”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

ALLOY SELECTION AND C-276 CODE DESIGN VALUE EXTENSION FOR ADVANCED MOLTEN SALT TECHNOLOGY TEST FACILITIES EXPERIMENTATION

Molten halide salts are being considered as working fluids for nuclear and concentrated solar power applications. High temperature molten fluoride and chloride salts are known to preferentially attack and deplete Cr in alloys, which leads to the use of high-Ni lower-Cr alloys in test facilities for advanced Molten Salt Technology. Alloys 600 and C-276 are two commercially available Ni alloys that have moderate Cr contents and are qualified to the maximum temperature of 649°C and 677°C (1,200°F and 1,251°F), respectively, in the Boiler and Pressure Vessel Code. Both alloys have good corrosion resistance to acids, are resistant to stress-corrosion cracking, and have long track records of use in the chemical industry. Comparatively, Alloy C-276 has a similar Cr content but much higher allowable stresses for temperatures greater than 600°C (1,112°F). Therefore, it has been considered as a structural material for test facilities that require operations at 700°C (1,292°F) or greater to develop high-temperature Molten Salt Technology. To meet the requirements, the current code design values were extended based on some experimental data. Analysis showed that above current Codified maximum temperature, strength of the alloy is mainly controlled by creep rupture life under the average stress, although the Sc creep rate criterion is close to the Favg.Savg rupture criterion. This paper presents the intended test facilities and the design requirements, alloy selection considerations, literature review, data analysis, and proposed allowable stress extension based on some creep test data for C-276 at temperatures greater than 677°C (1,251°F). Further research activities are also briefly mentioned.

Ren, Weiju↗
DOE OSTI2024

Reductive pathways in molten inorganic salts enable colloidal synthesis of III-V semiconductor nanocrystals

Colloidal quantum dots, with their size-tunable optoelectronic properties and scalable synthesis, enable applications in which inexpensive high-performance semiconductors are needed. Synthesis science breakthroughs have been key to the realization of quantum dot technologies, but important group III-group V semiconductors, including colloidal gallium arsenide (GaAs), still cannot be synthesized with existing approaches. The high-temperature molten salt colloidal synthesis introduced in this work enables the preparation of previously intractable colloidal materials. We directly nucleated and grew colloidal quantum dots in molten inorganic salts by harnessing molten salt redox chemistry and using surfactant additives for nanocrystal shape control. Synthesis temperatures above 425°C are critical for realizing photoluminescent GaAs quantum dots, which emphasizes the importance of high temperatures enabled by molten salt solvents. We generalize the methodology and demonstrate nearly a dozen III-V solid-solution nanocrystal compositions that have not been previously reported.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Modeling Molten Salt Reactor Fission Product Removal with SCALE

Liquid-fuel Molten Salt Reactors (MSRs) allow for continuous online fuel treatment and processing using a variety of subsystems. Among these subsystems, the off-gas system (OGS) continuously removes fission products from the primary fuel salt through a helium sparging process. Accurately modeling fission product behavior is paramount for the development of MSRs; while there are a variety of depletion modeling and simulation tools that allow for removal of material from a defined system, most of them work in a semicontinuous, batch-wise manner. The new tools implemented into TRITON, in the SCALE suite for reactor analysis and design, aim to address this issue by implementing truly continuous material feeds and removals. In addition, material accountancy is enhanced in these tools, which enable tracking of removed material in user-specified mixtures. These continuous depletion tools provide a way to model material transport throughout systems more efficiently and accurately. This report validates the new SCALE MSR modeling capabilities using data from the Molten Salt Reactor Experiment (MSRE). After a framework was established for deriving realistic removal rates based on design specifications, these rates were used by TRITON to continuously remove specific elements while performing burnup calculations. Results were compared to those obtained in MSRE, with a focus on the 135 Xe poison fraction. After these capabilities were validated, the learned concepts and best practices were applied to model the Molten Salt Breeder Reactor (MSBR) and the Molten Salt Demonstration Reactor (MSDR) to study the effects of continuous fission product removal in fuel salt reactivity, as well as the lifetime effects.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2021

Domestic Safeguards Material Control and Accountancy Considerations for Molten Salt Reactors

Molten salt reactors (MSRs) are a class of nuclear reactor designs with features and operational characteristics that vary significantly more than the class of light water reactors (LWRs). MSR design concepts can be broadly categorized as solid-fueled reactors with molten salt as the coolant, liquid-fueled reactors with fuel dissolved in molten salt coolant and liquid-fueled reactors with fuel dissolved in molten salt that is contained in distinct fuel tubes with a nonfissile coolant. Proposed MSR concepts include features that are specific to each design. MSR concepts vary widely across these design features, including the physical, chemical, and isotopic composition of fresh and irradiated fuel. Operational neutron energy spectrums and breeding ratios also vary significantly across design concepts. Some concepts are burner reactors designed to transmute the spent nuclear fuel from LWRs or pressurized heavy water reactors (PHWRs), while others are breeder reactors designed to breed fissile 233 U from naturally occurring fertile 232 Th. Some MSR concepts are designed to be a part of a once-through fuel cycle, while others involve chemical separation. Those that include plans to recycle the fuel differ by whether the chemical processing would be done onsite, as a process connected to the fuel salt itself, or offsite at a reprocessing facility similar to how LWR or PHWR spent fuel is reprocessed in some countries. Each overall design concept contains various aspects of each of these features to produce a unique facility

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Material Control & Accountancy for Molten Salt Reactors (FY2021 Report)

There is significant domestic and international interest, investment, and research and development momentum to pursue advanced nuclear reactor technologies. Molten salt reactor (MSR) concepts display the largest variability in fuel type and design features among the current advanced concepts. MSRs have been proposed with various core designs, sizes (power), and fuel cycles. Salt-fueled molten salt systems represent the only advanced reactor type with fuel that is not in a solid form during operation. These “liquid-fueled” MSRs are unique from perspectives of fuel fabrication, spent irradiated fuel and waste components, licensing, and material control and accountability (MC&A) including the potential of fissile material holdup. The liquid fuel salt is the defining distinction in comparison to other advanced reactors that propose TRI-structural ISOtropic particle fuel pebbles, various coolant options (e.g., molten salts or metals, high temperature gas), or small modular alternatives using solid fuel variants including both light water reactors and non-light water reactors. MSRs are appealing to the nuclear energy industry because of the diverse reactor characteristics they can support including various neutron energy spectra, fueling requirements, fuel cycles, and/or fuel utilization. However, because of the significant deviation and diversity of a salt-fueled system compared to traditional solid fuel light water-cooled reactors (LWRs), the history, regulatory licensing framework, modeling capabilities, and supporting engineering technology are either lacking or, in some cases, nonexistent. Therefore, the research community is actively supporting advanced MSR development on many of these fronts in particular to assist MSR vendors with licensing requirements. ORNL is leading the research and development of respective MC&A approaches for salt-fueled MSRs. This report summarizes the research performed at Oak Ridge National Laboratory (ORNL) under the US Department of Energy, Office of Nuclear Energy, Advanced Reactor Safeguards (ARS) program to investigate safeguards and security by design concepts, licensing and regulatory considerations, and dynamic system-level modeling to understand radioisotope concentrations for salt-fueled MSRs. The report builds upon the previous research and literature, identifies the MC&A challenges inherent to a salt-fueled MSR, reviews current regulatory frameworks for LWRs and their applicability towards salt-fueled MSRs, summarizes the status and progress of an MSR dynamic modeling tool, and discusses a prospective MC&A approach based on the Molten Salt Demonstration Reactor (MSDR) model.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2021

Signature Analysis Utilizing a Dynamic Molten Salt Reactor Model for MC&A

Moving from traditional fixed fuel nuclear reactor systems to a mobile, dynamic fuel system that has dissolved special nuclear material in a molten salt is a paradigm shift in several respects. One major consideration is how to develop effective nuclear material controls and accounting for these novel reactor systems. The Molten Salt Reactor Experiment is one example of a critical molten salt system and provided a significant reference library based on the documented effort. But it was low thermal power that was not intended to reflect a commercial scale electricity production design. Therefore, to facilitate and assist vendors with domestic licensing considerations, research is underway to identify methods that could be used for domestic safeguards approaches for these novel reactor systems. This research presents the results of a signature analysis of data generated from three simulated scenarios using the molten salt demonstration reactor model defined in the Transient Simulation Framework of Reconfigurable Modules. Each scenario provides 1 hour isotope inventories over a 180 day period. The scenarios investigated provide test cases to examine if direct gamma-ray spectroscopy of the fuel can be used to identify changes comparing a base case (no reactivity control and fixed fission contribution) to an insertion of reactivity (10 pcm no change in fission composition) and a change in fission composition. The analysis demonstrates that monitoring the total count rate in a highly collimated high-resolution photon energy spectrum is sensitive to perturbations imposed into the reactor model. The total photon count rate changes ≈2% for the fission composition change and ≈4.5% for the reactivity insertion compared to the base case. However, both scenarios show an increase in the total photon count rate. The total photon count rate can be used to identify changes due to power (number of fissions) but not due to a change in the material undergoing fission. To distinguish between the two cases of increased power, the photon spectrum would require an intensive analysis technique. A photon peak count rate ratio analysis could be used to identify changes in the fissile material fission generation in the core through identification of a static peak that shows little variation to the source of fission and a highly varying peak. The photon peak strength will ultimately be determined by the isotope’s fission yield. A preliminary analysis investigating the coupling of the isotope’s fission yield and its concentration in the fuel salt derived from the modeling has been performed. A ratio analysis of the photon peak count rates of 140 La to 99 Mo demonstrated that the reactivity insertion creates a distinct difference in the ratio compared to the fission composition change scenario.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

Hardness Prediction by Incorporating Heat Transfer and Molten Pool Fluid Flow in a Multi-pass, Multi-layer Weld for Onsite Repair of Grade 91 steel

Introduction: In the current fleet of fossil-fired power plants, creep strength enhanced ferritic steels (CSEF) are used to sustain the harsh service conditions. Enhanced properties of Grade 91 steel result from tempered martensite with a fine distribution of MX and M23C6 carbides. Grade 91 steel is subjected to onsite welding repair to remedy their degradation due to extreme service condition. Knowledge of weld repairability of these steels, such as as-welded hardness distribution, is essential to establishing sound repair procedures. Experimental trial and error tests can consume a lot of time as many welding variables need to be studied. For numerical modelling, most of the multi-pass multi-layer models are based on finite element method, which are limited to solve the heat conduction equation and ignore convective heat transfer due to melt flow. Moreover, the mesh has to be pre-built based on a known or assumed weld cross-section geometry. These finite element based models thus have limited predictive capability as defects are not considered and nugget size are pre-assumed. This research aims at developing a thermal and microstructure evolution model incorporating molten pool dynamics in a multi-pass multi-layer material deposition to predict the as-welded hardness distribution. Technical Approach: All the thermal, physical, and metallurgical properties of Grade 91 as a function of temperature are collected from the literature and inputted into the thermo-fluid model based on Flow-3D, a computational fluid dynamics software. A multi-pass, multi-layer material deposition is simulated where the melting of filler wire into the molten pool is directly considered based on the volume of fluid (VOF) method. The flow behaviour of the molten pool is used to understand the formation of deposition geometry and defects. The temperature profiles during the multi-pass, multi-layer welding are calculated. The results computed using the new model are compared against the experimental data of fusion zone geometry and thermal cycles. Hardness prediction in the heat-affected zone (HAZ) are made using Johnson-Mehl-Avrami (JMA) equation for solid-state phase transformation kinetics. The JMA parameters are extracted from the experimental data available in the literature. For comparison, a standard finite element heat conduction model is also developed to predict the thermal cycles and hardness distribution in the multi-pass, multi-layer weld. Expected Result: Results obtained using the molten pool dynamic simulation versus the finite element heat conduction model are compared. Specifically, the effects of convective heat transfer on the accuracy of the calculated thermal history, bead shape and size, and HAZ hardness distribution are examined.

Modeling, Grade 91 steel, Multi-pass multi-layer d↗
DOE OSTI2023

Property Measurements of NaCl-UCl 3 and NaCl-KCl-UCl 3 Molten Salts (Rev.1)

Thermochemical and thermophysical property values of several salt compositions of interest are needed by molten salt reactor (MSR) developers to design, license, and operate their reactors. Thermochemical and thermophysical properties being measured at Argonne include thermal transitions, phase behavior, heat capacity, density, volumetric thermal expansion of the liquid phase, thermal diffusivity, thermal conductivity, and viscosity. Several properties of eutectic compositions in the ternary NaCl-KCl-UCl 3 and binary NaCl-UCl 3 systems that may be used by MSR developers as fuel bearing salts are being measured. A 65.8 mol % NaCl–34.2 mol % UCl 3 mixture and a near-eutectic mixture of 50.9 mol % NaCl–24.4 mol % KCl–24.7 mol % UCl 3 were synthesized and the thermochemical properties of the mixtures were measured by using differential scanning calorimetry (DSC). The measured transition temperatures were compared to transition temperatures predicted using two models. A thermodynamic model of the binary NaCl-UCl 3 system was constructed using data in the Molten Salt Thermal Properties Database–Thermochemical Version 2.0 (MSTDB-TC V2.0). A ternary NaClKCl-UCl 3 system model constructed at Argonne and was described in a previous report. These comparisons can be used to validate the models. Thermophysical property values of molten salts are needed to model how salt retains and transfers heat in an MSR system. These property values are essential to the entire MSR design because molten salt is used as both the fuel and the coolant material in a salt fueled reactor. Heat capacity of the synthesized NaCl-UCl 3 and NaCl-KCl-UCl 3 salt mixtures was measured by using DSC and thermal diffusivity was measured by using laser flash analysis (LFA) at temperatures spanning the typical operating range of an MSR.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Report on Initial Tribological Studies of Graphite in Dry Argon and Molten Salt Environment

This report documents completion of the Advanced Reactor Technologies (ART) Level 2 Milestone M2TG-24OR0501081: “Complete report on initial tribological studies within molten salt environment”, due January 31, 2024. This milestone is a carryover milestone from FY23 M2TG-23OR0501091. The report summarizes the initial studies on tribological characterization of the graphite–graphite sliding interface in a dry argon and molten FLiNaK salt environment. The experiments were conducted on a high-temperature multifunctional tribometer placed in a glovebox. This configuration enables probing the wear and friction properties at high temperatures in an inert environment. The worn surfaces were analyzed using high-resolution microscopy and white-light profilometry to determine the wear modes and wear rates. This report discusses the previous wear and friction studies on 316H stainless steel (SS) sliding against graphite in molten salt for different temperatures, sliding speeds, and salt amount. Moreover, key tribological parameters of pebble-on-pebble interaction in gas-cooled and molten salt reactors (MSRs) are analyzed and used to design an experimental test matrix for future studies. The outcomes of this project could provide key information about the tribological behavior of graphite pebbles in gas-cooled and MSRs, thereby contributing to safer operation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Method for Real-Time Salt Aerosol Concentration and Size Measurements for Molten Salt Reactor Safety Assessments

Licensing a new nuclear reactor involves evaluating credible accident scenarios by developing models that simulate accident progression to predict possible outcomes and their impact on safety. The formation of radionuclide-bearing aerosols in the respirable size range can significantly affect dose consequence and threaten human health and is therefore a focus of nuclear reactor safety assessments. Recent reviews of the literature identified a lack of existing experimental data describing the mechanisms of formation and properties (size, concentration, and composition) of radionuclide-bearing aerosols that may be produced from molten salt reactor (MSR) facilities during postulated accident scenarios. Experiments on aerosol formation from molten salt systems are a high priority need that will support MSR licensing by indicating the radiological consequences of aerosol formation and providing the data required for model development and validation. The evolving conditions that occur during a MSR accident, such as a spill of molten fuel salt, may affect aerosol formation mechanisms and aerosol properties over time. There is a need to conduct experiments that simulate credible MSR accidents in a laboratory to generate aerosols with realistic characteristics and behaviors and a need to measure these aerosols in real time under accident-relevant conditions. This report describes the development of a method that can be used to quantify the size and concentration of salt aerosol particles that form from molten salt systems in real time. This method will be employed in future integral effects tests that are conducted at an engineering scale to simulate realistic MSR accidents and in future separate effects tests that will provide mechanistic insight into aerosol formation and properties to support process model development.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

An Overview of the Molten Salt Thermal Properties Database–Thermophysical, Version 4.0 (MSTDB-TP V.4.0)

A central repository of thermophysical and thermochemical properties of molten salt compositions of relevance to molten salt reactors (MSRs) is vital in supporting the broad community of MSR developers, who are at various stages of developing and deploying their reactor designs. In general, these MSR designs differ significantly from developer to developer (e.g., with respect to the hardness of the neutron spectra, level of fissile loading, target multicomponent temperatures and power levels, and moderating capabilities). Therefore, the fuel and coolant salts being considered vary greatly: they may be chlorides or fluorides, they utilize different actinides at different ratios, and the cations in the melt are selected based on perceived advantages and disadvantages. Considering the general need for thermal properties, and the vastness of the array of potential candidate salt mixtures, the Molten Salt Thermal Properties Database (MSTDB) was initiated in 2018 with the goal of providing thermophysical and thermochemical characterization of key molten salt compounds and mixtures across their temperature and compositional domains. The MSTDB is thus divided into the thermophysical arm (MSTDB-TP) and the thermochemical arm (MSTDB-TC). The MSTDB is an effort funded by the Department of Energy, Office of Nuclear Energy (DOE-NE) Nuclear Energy Advanced Modeling and Simulation (NEAMS) program, and the MSR Campaign. This report provides an overview of the MSTDB-TP v4.0 in terms of the data contained within, the state of the tools used to access the data, the availability of predictive models that leverage the raw data in the database, the preliminary status of developmental efforts that are currently underway, and an account of future goals for MSTDB-TP. The primary goal for the update from MSTDB-TP v.3.1 to v4.0 was the incorporation of surface tension data into the database; this property is important for thermal hydraulics modeling and species transport in other tools that have been developed under the NEAMS program. A breakdown of the surface tension data that have been added into MSTDB-TP v4.0 is provided herein, and the manner in which the quality of the data has been assessed is also documented. For MSTDB-TP v4.0, newly published thermophysical property data—primarily from collaborative experimental efforts under the MSR Campaign—have been incorporated into the database, and the resulting expansion is documented here. Because of the size to which MSTDB-TP has grown, the raw data format has now been recast into JavaScript Object Notation (JSON) format for easier connection with the MSTDB-TP application programming interface (API). Saline; the pre-existing comma-separated value (CSV) format has been deprecated but is still maintained, accessible, and up to date. As a final effort in packaging the MSTDB-TP v4.0 update, the graphical user interface (GUI) for MSTDB has been updated to allow full accessibility to the density and viscosity predictive models, which are based on Redlich-Kister expansions of MSTDB-TP raw data. Some other major aspects of this report, in terms of preliminary and future work, include: (1) documentation of the formalism and preliminary testing of a kinetic theory model that may act as a predictive model for thermal conductivity; (2) documentation of the candidate predictive models that may be considered in the future for surface tension, making use of the surface tension data now in MSTDB-TP v4.0; (3) a preliminary account of a data collection process that will enable the filling of additional gaps within MSTDB-TP, namely with data which have been collected computationally (e.g., through ab initio molecular dynamics).

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Real-Time Characterization of Salt Aerosols Generated from Static and Sparged Molten Salt

The formation of radionuclide-bearing aerosols in the respirable size range has the potential to significantly influence offsite dose consequences and is, therefore, an important consideration in nuclear facility safety assessments. Molten salt reactor (MSR) developers will likely need to demonstrate an understanding of the conditions under which radionuclide-bearing aerosols may be generated from their reactor under normal operating and accident conditions, as well as the characteristics and transport behavior of these aerosols, to demonstrate to the U.S. Nuclear Regulatory Commission (NRC) that the facility can be operated safely. Recent reviews of the literature identified a lack of experimental data describing the mechanisms of formation and properties (size, concentration, and composition) of salt aerosol particles that are produced from molten salts. Experiments that identify the conditions that lead to radionuclide-bearing salt aerosol releases and quantify the characteristics of salt aerosols formed by different mechanisms are high-priority needs to support MSR licensing. This report describes tests that were conducted within the Argonne Salt Aerosol Test Stand (a sealed vessel and measurement system) to generate salt aerosols from static and sparged molten salts and measure their size and concentration in real-time. The results provide insight into salt aerosol formation by the vapor condensation and bubble bursting mechanisms and inform the potential radiological consequences of aerosol formation from molten fuel salt. Videos of the salt surface were taken during salt sparge tests to observe surface bubble behavior. The data in this report can be used to develop mechanistic source term and accident progression models for MSRs. The real-time salt aerosol characterization technique used in this study will be employed in future integral effects tests that are conducted at an engineering scale to simulate realistic MSR accidents and in future separate effects tests to address additional variables that may impact salt aerosol characteristics (e.g., presence of fission products in salt and humidity in atmosphere).

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Molten sodium batteries: advances in chemistries, electrolytes, and interfaces

The need for clean, renewable energy has driven the expansion of renewable energy generators, such as wind and solar. However, to achieve a robust and responsive electrical grid based on such inherently intermittent renewable energy sources, grid-scale energy storage is essential. The unmet need for this critical component has motivated extensive grid-scale battery research, especially exploring chemistries “beyond Li-ion”. Among others, molten sodium (Na) batteries, which date back to the 1960s with Na-S, have seen a strong revival, owing mostly to raw material abundance and the excellent electrochemical properties of Na metal. Recently, many groups have demonstrated important advances in battery chemistries, electrolytes, and interfaces to lower material and operating costs, enhance cyclability, and understand key mechanisms that drive failure in molten Na batteries. For widespread implementation of molten Na batteries, though, further optimization, cost reduction, and mechanistic insight is necessary. In this light, this work provides a brief history of mature molten Na technologies, a comprehensive review of recent progress, and explores possibilities for future advancements.

25 ENERGY STORAGE↗
DOE OSTI2024

The Melting Behavior of Hydrogen Direct Reduced Iron in Molten Steel and Slag: An Integrated Computational and Experimental Study

Direct reduced iron (DRI) and hot briquetted iron (HBI) are essential feedstocks for tramp element control in the electric arc furnace (EAF). Due to greenhouse gas (GHG) concerns related to CO2 emissions, hydrogen as a substitute for natural gas and a reductant in DRI production is being widely explored to reduce GHG emissions in ironmaking. This study examines the melting behavior of hydrogen DRI (H-DRI) pellets in the EAF containing low-carbon (0.1 wt.%) molten steel and molten slag. A computational heat transfer model was developed to predict the melting behavior of H-DRI pellets. To validate the model, a set of experimental laboratory simulations was conducted by immersing H-DRI in a molten steel bath and slag. The temperature history at the center of the pellet during melting and the shell thickness at different melting stages were utilized to validate the model. The simulation results agree with the experimental measurements of steel balls and H-DRI in different metallic molten steel and slag baths.

Materials Science↗
NASA NTRS1989

Compatibility of molten salts with advanced solar dynamic receiver materials

Metal-coated graphite fibers are being considered as a thermal conductivity enhancement filler material for molten salts in solar dynamic thermal energy storage systems. The successful metal coating chosen for this application must exhibit acceptable wettability and must be compatible with the molten salt environment. Contact angle values between molten lithium fluoride and several metal, metal fluoride, and metal oxide substrates have been determined at 892 C using a modification of the Wilhelmy plate technique. Reproducible contact angles with repeated exposure to the molten LiF indicated compatibility.

Jaworske, D. A.↗
NASA NTRS1996

Corrosion of Mullite by Molten Salts

The interaction of molten salts of different Na2O activities and mullite is examined with furnace and burner tests. The more-acidic molten salts form small amounts of Al2O3; the more-basic molten salts form various Na2O-Al2O3-SiO2 compounds. The results are interpreted using the Na2O-Al203-SiO2 ternary phase diagram, and some possible diffusion paths are discussed. The generally higher melting points of Na2O-Al2O3-SiO2 compounds lead to better behavior of mullite in molten salts, as compared to SiO2-protected ceramics such as SiC. Mullite-coated SiC is discussed, and the corrosion behavior is evaluated.

Jacobson, Nathan S.↗
NASA NTRS1983

Conduit for high temperature transfer of molten semiconductor crystalline material

A conduit for high temperature transfer of molten semiconductor crystalline material consists of a composite structure incorporating a quartz transfer tube as the innermost member, with an outer thermally insulating layer designed to serve the dual purposes of minimizing heat losses from the quartz tube and maintaining mechanical strength and rigidity of the conduit at the elevated temperatures encountered. The composite structure ensures that the molten semiconductor material only comes in contact with a material (quartz) with which it is compatible, while the outer layer structure reinforces the quartz tube, which becomes somewhat soft at molten semiconductor temperatures. To further aid in preventing cooling of the molten semiconductor, a distributed, electric resistance heater is in contact with the surface of the quartz tube over most of its length. The quartz tube has short end portions which extend through the surface of the semiconductor melt and which are lef bare of the thermal insulation. The heater is designed to provide an increased heat input per unit area in the region adjacent these end portions.

Fiegl, George↗
NASA NTRS2010

Development and Testing of High Surface Area Iridium Anodes for Molten Oxide Electrolysis

Processing of lunar regolith into oxygen for habitat and propulsion is needed to support future space missions. Direct electrochemical reduction of molten regolith is an attractive method of processing, because no additional chemical reagents are needed. The electrochemical processing of molten oxides requires high surface area, inert anodes. Such electrodes need to be structurally robust at elevated temperatures (1400-1600 C), be resistant to thermal shock, have good electrical conductivity, be resistant to attack by molten oxide (silicate), be electrochemically stable and support high current density. Iridium with its high melting point, good oxidation resistance, superior high temperature strength and ductility is the most promising candidate for anodes in high temperature electrochemical processes. Several innovative concepts for manufacturing such anodes by electrodeposition of iridium from molten salt electrolyte (EL-Form process) were evaluated. Iridium electrodeposition to form of complex shape components and coating was investigated. Iridium coated graphite, porous iridium structure and solid iridium anodes were fabricated. Testing of electroformed iridium anodes shows no visible degradation. The result of development, manufacturing and testing of high surface, inert iridium anodes will be presented.

Shchetkovskiy, Anatoliy↗