SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The overarching objective of this project was developing a new sealant product and technology that significantly mitigate CO 2 leakage and increase reservoir storage efficiency for various wellbore conditions and chemical environments
The loss of platinum (Pt) electrochemically active surface area (ECSA) is a critical degradation mode that often becomes a limiting factor for heavy-duty proton exchange membrane fuel cell vehicles. High surface area carbon supports have been shown to improve Pt dispersion and limit detrimental ionomer-electrocatalyst interactions due to their large interior pore volume. Here, in this work, using automated scanning transmission electron tomography, the degradation of nanoparticles located on the interior versus exterior surfaces of the carbon support is compared following a catalyst-specific accelerated stress test (AST) of 90,000 voltage cycles between 0.6 V to 0.95 V. The results reveal a notable increase in median particle size for both interior and exterior Pt catalyst particles, with a slightly higher increase in particle size distribution and loss of specific surface area for the particles located on the exterior carbon surface. The fraction of Pt nanoparticles that reside within the interior of the carbon support also increased following the AST test, accompanied by evidence of an increase in average carbon mesopore size. Here, the results shed light on the degradation mechanisms affecting electrochemical properties and the enhanced particle accessibility at lower relative humidity.
Transparent conductive oxides (TCOs), such as indium tin-doped oxide (ITO), are ubiquitous as components of electronics and are ideal electrode substrates for catalysis, energy transformation reactions, and energy storage applications. Recently, researchers have recognized their effectiveness as electrode materials for manipulating actinide oxidation states in solution. Despite their popularity as electrode materials, prior studies focused extensively on the direct radiolysis of TCO materials in air and rarely examined these effects within a solution, limiting our fundamental understanding of the interactions between solvent radiolysis products and these substrates in high radiation environments. Here, in this study, we characterize the effects of solvent radiolysis products—arising from the gamma irradiation of water, aqueous nitric acid solutions, and n-dodecane—on the composition, surface speciation, and band structure of ITO thin films on a glass substrate as a function of absorbed dose using UV-visible spectroscopy, scanning electron microscopy, photoelectrochemistry, and X-ray photoelectron spectroscopy. Our work demonstrates that mesoporous thin film electrodes of ITO exposed to gamma radiation in each solvent accumulate defects and exhibit solvent and dose dependent changes to their surface and interfacial properties. These electrodes maintain their electrochemical function and improve their photoelectrochemical performance up to at least 100 kGy of accumulated gamma dose, confirming their utility in solvents exposed to ionizing radiation fields.
Smectite-based adsorbents are increasingly being studied as sustainable packaging materials for scavenging ethylene, a plant hormone that accelerates fruit ripening. However, the mechanisms governing their uptake and retention remain poorly understood. Here, to tackle this question we systematically investigate ethylene gas-solid interactions in pristine, acid-activated, and choline-functionalized montmorillonites using a complementary combination of structural, gravimetric, and spectroscopic techniques, including inelastic neutron scattering. We experimentally distinguish ethylene populations associated with interlayer confinement, mesopore, and external surface adsorption. We show that chemical functionalization distinctly controls adsorption pathways: acid activation enhances total uptake by generating mesoporous adsorption sites and promoting partial interlayer intercalation, yielding capacities comparable to those of leading smectite-based adsorbents, while choline functionalization promotes preferential confinement and stabilization of guest molecules within the interlayer galleries. Advanced spectroscopic analysis provides molecular-level insight into confinement environments and interaction strengths. We also establish clear structure-property relationships by correlating uptake values derived from independent techniques, linking chemical modification, accessible adsorption domains, and retention behavior. These findings provide general design principles for tuning gas-solid interactions in functionalized layered silicates and highlight their potential as adaptable platforms for sustainable ethylene gas capture and selective adsorption technologies.
Herein, we demonstrate that the performance of mesoporous silica SBA-15 and SBA-15-Ag during plasma ammonia synthesis depends on the plasma conditions. At high power, the mesoporous silica SBA-15 without Ag produces the largest amount of ammonia, but the addition of Ag provides a minor benefit at lower powers. Plasma conditions were analyzed through optical emission spectroscopy using N 2 , N 2 + , and NH molecular bands and H α line. Stark broadening of H α line was used to find electron density, and N 2 molecular bands were used to assess N 2 vibrational excitation, important for plasma nitrogen decomposition. At similar input conditions, reactors with SBA-15 have higher electron density and higher N 2 vibrational temperature. Consistent with higher electron density, SBA-15 reactors have stronger N 2 + emission intensity relative to the neutral N 2 . The addition of Ag results in higher N 2 rotational temperature, possibly due to localized heating. From the materials point of view, SBA-15 is a more robust catalyst with good surface area retention after plasma exposure due to the lack of local heating generated when a metal is in the structure. Furthermore, we identify two possible regimes during ammonia synthesis, a metal and a surface-plasma driven. At lower plasma densities, the addition of metal is beneficial, while at higher power and plasma density, the best performance is achieved without the aid of a metal catalyst.
Direct air capture (DAC) of CO 2 by solid porous materials represents an attractive “negative emission” technology. However, state-of-the-art sorbents based on supported amines still suffer from unsolved high energy consumption and stability issues. For this work, taking clues from the CO 2 interaction with superbase-derived ionic liquids (SILs), high-performance and tunable sorbents in DAC of CO 2 was developed by harnessing the power of CaO- and SIL-engineered sorbents. Deploying mesoporous silica as the substrate, a thin CaO layer was first introduced to consume the surface-OH groups, and then active sites with different basicities (e. g., triazolate and imidazolate) were introduced as a uniformly distributed thin layer. The as-obtained sorbents displayed high CO 2 uptake capacity via volumetric (at 0.4 mbar) and breakthrough test (400 ppm CO 2 source), rapid interaction kinetics, facile CO 2 releasing, and stable sorption/desorption cycles. Operando diffuse reflectance infrared Fourier transformation spectroscopy (DRIFTS) analysis under simulated air atmosphere and solid-state NMR under 13 CO 2 atmosphere demonstrated the critical roles of the SIL species in low-concentration CO 2 capture. The fundamental insights obtained in this work provide guidance on the development of high-performance sorbents in DAC of CO 2 by leveraging the combined advantages of porous solid scaffolds and the unique features of CO 2 -philic ionic liquids.
This work details the synthesis, materials characterization and absorption capacity of graphene aerogel (GA) loaded with UiO-66-NH 2 metal organic framework (MOF). Throughout the study, a series of density-tunable MOF/GA composites were synthesized by adjusting the MOF/graphene oxide (GO) mass ratio of the precursors before hydrothermal reduction and subsequent critical point drying to achieve MOF-x%/GA composites, with x, ranging from 0 to 100, denoting the weight percent ratio of MOF to GO in the starting solution. Scanning electron microscopy (SEM) images and Barrett-Joyner-Halenda (BJH) pore size calculations supported that MOF loading enlarged the macroporous (>50 nm) structure of the GA framework but had no influence on the mesoporous (2–50 nm) structure of GA. The degree of MOF loading first decreased and then increased the density of resulting composites, exhibiting a minimum for the 10–30% samples. Such behavior with respect to MOF loading has not been reported previously. MOF-x%/GA samples were further investigated for absorption capacity using various organic liquids. MOF-30%/GA proved to be the best absorbent sample for all solvents tested, achieving the highest capacity for chloroform at 147.0 ± 10.0 mg/mg. The behavior is attributed to the structural changes induced by the MOF incorporation as well as the interactions between the organic molecules and the MOF.
Prediction of fluid properties in microporous and mesoporous confinement is non-trivial due to distinct influences from pore surface functionality and shape and fluid molecular characteristics. The vast majority of literature focuses nearly exclusively on a small number of components that are generally low molecular weight gases and vapors. Missing are studies that utilize a relatively large number of compounds that are liquid at ambient conditions to probe the impact of molecular shape and size on confined fluid properties. Such materials are of great interest in the extraction of oil and gas from shale reservoirs or for the design of selective adsorbents for chemical separation. In this work, we reveal non-intuitive relationships that emerge when comparing bulk fluid properties to those when confined in amorphous silica single-digit nanopores (approx. 5 nm SBA-15), specifically the confined density and self-diffusivity. A counterintuitive result was obtained where larger molecules had relatively faster self-diffusivities; however, this behavior was revealed to be caused by these larger compounds exhibiting a relatively low density when confined. As the prediction of confined fluid properties impacts a diversity of disciplines, the results highlight the need for additional investigations where consistent and large-scale experimental procedures are employed.
Recent studies have shown that dynamic nuclear polarization (DNP) can be used to detect 17 O solid-state NMR spectra of naturally abundant samples within a reasonable experimental time. Observations using indirect DNP, which relies on 1 H mediation in transferring electron hyperpolarization to 17 O, are currently limited mostly to hydroxyls. Direct DNP schemes can hyperpolarize non-protonated oxygen near the radicals; however, they generally offer much lower signal enhancements. In this study, we demonstrate the detection of signals from non-protonated 17 O in materials containing silicon. The sensitivity boost that made the experiment possible originates from three sources: indirect DNP excitation of 29 Si via protons, indirect detection of 17 O through 29 Si nuclei using two-dimensional 29 Si{ 17 O} D-HMQC, and Carr-Purcell-Meiboom-Gill refocusing of 29 Si magnetization during acquisition. This 29 Si-detected scheme enabled, for the first time, 2D 17 O– 29 Si heteronuclear correlation spectroscopy in mesoporous silica and silica-alumina surfaces at natural abundance. In contrast to the silanols showing motion-averaged 17 O signals, the framework oxygens exhibit unperturbed powder patterns as unambiguous fingerprints of surface sites. Furthermore, along with hydroxyl oxygens, detection of these moieties will help in gaining more atomistic-scale insights into surface chemistry.
Abstract Fast energy storage via intercalation requires quick ionic diffusion and often results in pseudocapacitive behavior. The cycling stability of such energy storage materials remains understudied despite the relevance to lifetime cost. Orthorhombic niobium oxide (T‐Nb 2 O 5 ) is a rapid ion intercalation material with a theoretical capacity of 201.7 mAh g −1 (Li 2 Nb 2 O 5 ) and good cycling stability due to the minimal unit cell strain during (de)intercalation. Prior reports of T‐Nb 2 O 5 cycling between 1.3–3.1 V versus Li/Li + noted a 50% loss in capacity after 10 000 cycles. Here, cyclic voltammetry is used to identify the role of the voltage window, state of charge, and potentiostatic holds on the cycling stability of mesoporous T‐Nb 2 O 5 thin films. Films cycled between 1.2–3.0 V versus Li/Li + without voltage holds (Li 1.1 Nb 2 O 5 ) exhibited extreme cycling stability with 90.8% capacity retention after 0.25 million cycles without detectable morphological/crystallographic changes. In contrast, the inclusion of 60 s voltage holds (Li 2.18 Nb 2 O 5 ) led to rapid capacity loss with 61.6% retention after 10 000 cycles with corresponding X‐ray diffraction evidence of amorphization. Cycling with other limited voltage windows identifies that most crystallographic degradation occurs at higher extents of lithiation. These results reveal remarkable stability over limited conditions and suggest that T‐Nb 2 O 5 amorphization is associated with high extents of lithiation.
Vanadium oxides are widely tunable materials, with many thermodynamically stable phases suitable for applications spanning catalysis to neuromorphic computing. The stability of vanadium in a range of oxidation states enables mixed-valence polymorphs of kinetically accessible metastable materials. Low-temperature synthetic routes to, and the properties of, these metastable materials are poorly understood and may unlock new optoelectronic and magnetic functionalities for expanded applications. In this work, we demonstrate topochemical reduction of α-V 2 O 5 to produce metastable vanadium oxide phases with tunable oxygen vacancies (>6%) and simultaneous substitutional tin incorporation (>3.5%). The chemistry is carried out at low temperature (65 °C) with solution-phase SnCl 2 , where Sn 2+ is oxidized to Sn 4+ as V 5+ sites are reduced to V 4+ during oxygen vacancy formation. Despite high oxygen vacancy and tin concentrations, the transformations are topochemical in that the symmetry of the parent crystal remains intact, although the unit cell expands. Band structure calculations show that these vacancies contribute electrons to the lattice, whereas substitutional tin contributes holes, yielding a compensation doping effect and control over the electronic properties. The SnCl 2 redox chemistry is effective on both solution-processed V 2 O 5 nanoparticle inks and mesoporous films cast from untreated inks, enabling versatile routes toward functional films with tunable optical and electronic properties. The electrical conductance rises concomitantly with the SnCl 2 concentration and treatment time, indicating a net increase in density of free electrons in the host lattice. This work provides a valuable demonstration of kinetic tailoring of electronic properties of vanadium–oxygen systems through top-down chemical manipulation from known thermodynamic phases.
Cage topology controlled at the nanometer length scale is expected to enable original functionalities, e.g., in catalysis and therapeutics. Cages are fundamental structural motifs of clathrates and their topological duals, Frank-Kasper phases, and are constituents of mesoporous silica frameworks. However, with one exception, they have not been synthesized as discrete particles. By varying reactant ratios of surfactant, oil, and silane, we report the discovery of 5(12)6(2) and 5(12)6(8) amorphous silica polyhedra, each coexisting with the previously identified 5(12) cage, using combined cryo-transmission electron microscopy (cryo-TEM) and single-particle reconstruction (SPR). Notably, the 5(12)6(8) polyhedron represents a topology not previously observed in mesoporous silica frameworks. Control over structural features is demonstrated, and insights into cage formation mechanisms are provided. Structural outcomes are summarized in a ternary morphology diagram alongside prior results, bridging serendipitous discovery and intentional design of silica cages displaying a level of control over silica polymerization rivaling nature.
The primary goal of this project is to leverage data-driven methods and machine learning strategies to develop accurate multi-physics models for all-solid-state Li-S battery (ASLSB) materials that can capture electrochemical and transport phenomena over atomic to mesoscopic length/timescales. These models will be rigorously validated by synthesis and advanced characterization experiments. The team will leverage the predictive power of these models, alongside synthesis/characterization experiments and battery fabrication to address longstanding issues at the electrode/electrolyte interfaces in ASLSBs. The project’s proposed technology involves the following: (1) halide-doped solid sulfide electrolytes that can concurrently provide high Li + ion conductivity and suppress dendrite growth; (2) novel mesoporous cathode composed of super-P and carbon nanotubes co-infiltrated with sulfur and sulfide electrolyte, which hold potential to allow high sulfur loading and optimal ion/electron pathways; and (3) functionalization of sulfide electrolyte with ionic liquids to improve physical contact and minimize impedance at the cathode/electrolyte interface. Successful development of proposed predictive models (at multiple scales) will bridge this knowledge gap and will advance fundamental understanding of reaction chemistry, kinetics, charge transfer, and dendrite growth at electrified SSIs. This will enable predictive design of effective strategies to mitigate interfacial problems in ASSLSBs, including poor interfacial contact, interfacial impedance to Li + ion transport, and poor electron/ion conduction within cathodes. Ultimately, the fundamental knowledge gained will lead to development of high-performance ASSLSBs.
Micro- and nanoscale information on the activating and deactivating coking behaviour of zeolite catalyst materials increases our current understanding of many industrially applied processes, such as the methanol-to-hydrocarbon (MTH) reaction. Atom probe tomography (APT) was used to reveal the link between framework and coke elemental distributions in 3D with sub-nanometre resolution. APT revealed 10–20 nanometre-sized Al-rich regions and short-range ordering (within nanometres) between Al atoms. With confocal fluorescence microscopy, it was found that the morphology of the zeolite crystal as well as the secondary mesoporous structures have a great effect on the microscale coke distribution throughout individual zeolite crystals over time. Additionally, a nanoscale heterogeneous distribution of carbon as residue from the MTH reaction was determined with carbon-rich areas of tens of nanometres within the zeolite crystals. Finally, a short length-scale affinity between C and Al atoms, as revealed by APT, indicates the formation of carbon-containing molecules next to the acidic sites in the zeolite.
Abstract The synthesis of a wavy mesoporous 2D covalent organic framework (COF) with a 6‐nm hexagonal pore lattice ( Joa‐COF‐1 ) is reported. This has been achieved by the synthesis of a terpyrenyl linker of approximately 2.7 nm in length and its subsequent condensation with a 3‐connected non‐planar cata‐hexabenzocoronene. Joa‐COF‐1 exists as non‐covalent tubular domains composed of π‐stacked 4 to 5 pores in 2D COF sections that can be separated by mild sonication, resulting in a family of tubular COF nanostructures that combine a 1D morphology with accessible mesopores.
Abstract The synthesis of a wavy mesoporous 2D covalent organic framework (COF) with a 6‐nm hexagonal pore lattice ( Joa‐COF‐1 ) is reported. This has been achieved by the synthesis of a terpyrenyl linker of approximately 2.7 nm in length and its subsequent condensation with a 3‐connected non‐planar cata‐hexabenzocoronene. Joa‐COF‐1 exists as non‐covalent tubular domains composed of π‐stacked 4 to 5 pores in 2D COF sections that can be separated by mild sonication, resulting in a family of tubular COF nanostructures that combine a 1D morphology with accessible mesopores.