Results for “materials evaluation” — Page 13

NASA NTRS1981

Energy efficient engine high-pressure turbine single crystal vane and blade fabrication technology report

The objective of the High-Pressure Turbine Fabrication Program was to demonstrate the application and feasibility of Pratt & Whitney Aircraft-developed two-piece, single crystal casting and bonding technology on the turbine blade and vane configurations required for the high-pressure turbine in the Energy Efficient Engine. During the first phase of the program, casting feasibility was demonstrated. Several blade and vane halves were made for the bonding trials, plus solid blades and vanes were successfully cast for materials evaluation tests. Specimens exhibited the required microstructure and chemical composition. Bonding feasibility was demonstrated in the second phase of the effort. Bonding yields of 75 percent for the vane and 30 percent for the blade were achieved, and methods for improving these yield percentages were identified. A bond process was established for PWA 1480 single crystal material which incorporated a transient liquid phase interlayer. Bond properties were substantiated and sensitivities determined. Tooling die materials were identified, and an advanced differential thermal expansion tooling concept was incorporated into the bond process.

Giamei, A. F.↗

NASA NTRS1983

An Evaluation of Techroll Seal Flexible Joint Material

This study evaluated the materials utilized in the flexible joint for possible failure modes. Studies undertaken included effect of temperature on the strength of the system, effect of fatigue on the strength of the system, thermogravimetric analysis, thermochemical analysis, differential scanning calorimeter analysis, dynamic mechanical analysis, and peel test. These studies indicate that if the joint failed due to a materials deficiency, the most likely mode was excessive temperature in the joint. In addition, the joint material is susceptible to fatigue damage which could have been a contributing factor.

Hall, W. B.↗

NASA NTRS1986

Factors influencing the ultrasonic stress wave factor evaluation of composite material structures

To demonstrate that the finite-element model can be used to investigate some of the factors influencing the ultrasonic stress wave evaluation of materials, a hypothetical case was studied in which classical vibration theory was used. Vibration analysis and experiments for the undamaged case were conducted on an isotropic aluminum plate and a unidirectional graphite-epoxy plate, using a point source to excite the plates. The finite-element solution correlated within eight percent with the exact method. The frequencies predicted by the finite-element model were observed in the experiments in both plates, although in the composite plate, additional frequencies were observed which could not be accounted for. Damaged isotropic plates were also considered. The effects of increasing damage severity with constant damage area, and increasing damage area with constant severity on the resonant frequencies were analyzed.

Rebello, C. J.↗

NASA NTRS1985

Testing Ceramics for Diesel Engines

Adaptation of diesel engine allows prestressed ceramic materials evaluated under realistic pressure, temperature, and stress without introducing extraneous stress. Ceramic specimen part of prechamber of research engine. Specimen held in place by clamp, introduces required axial compressive stress. Specimen -- cylindrical shell -- surrounded by chamber vented or pressurized to introduce requisite radial stress in ceramic. Pressure chamber also serves as safety shield in case speimen disintegrates. Materials under consideration as cylinder liners for diesel engines.

Schneider, H. W.↗

NASA NTRS1988

Performance of lightweight nickel electrodes

The NASA Lewis Research Center is currently developing nickel electrodes for nickel-hydrogen (Ni-H2) batteries. These electrodes are lighter in weight and have higher energy densities than the heavier state-of-the-art (SOA) sintered nickel electrodes. In the present approach, lightweight materials or plaques are used as conductive supports for the nickel hydroxide active material. These plaques (fiber and felt, nickel plated plastic and graphite) are commercial products that are fabricated into nickel electrodes by electrochemically impregnating them with active material. Evaluation is performed in half cells structured in the bipolar configuration. Initial performance tests include capacity measurements at five discharge levels, C/2, 1.0C 1.37C, 2.0C and 2.74C. The electrodes that pass the initial tests are life cycle tested in a low Earth orbit regime at 80 percent depth of discharge. Different formulations of nickel fiber materials obtained from several manufacturers are currently being tested as possible candidates for nickel electrodes. One particular lightweight fiber mat electrode has accumulated over 3000 cycles to date, with stable capacity and voltage. Life and performance data of this electrode were investigated and presented. Good dimensional stability and active material adherence have been demonstrated in electrodes made from this lightweight plaque.

Britton, Doris L.↗

NASA NTRS1988

Performance of lightweight nickel electrodes

The NASA Lewis Research Center is currently developing nickel electrodes for nickel-hydrogen (Ni-H2) batteries. These electrodes are lighter in weight and have higher energy densities than the heavier state-of-the-art (SOA) sintered nickel electrodes. In the present approach, lightweight materials or plaques are used as conductive supports for the nickel hydroxide active material. These plaques (fiber and felt, nickel plated plastic and graphite) are commercial products that are fabricated into nickel electrodes by electrochemically impregnating them with active material. Evaluation is performed in half cells structured in the bipolar configuration. Initial performance tests include capacity measurements at five discharge levels, C/2, 1.0C, 1.37C, 2.0C and 2.74C. The electrodes that pass the initial tests are life cycle tested in a low earth orbit regime at 80 percent depth of discharge. Different formulations of nickel fiber materials obtained from several manufacturers are currently being tested as possible candidates for nickel electrodes. One particular lightweight fiber mat electrode has accumulated over 3000 cycles to date, with stable capacity and voltage. Life and performance data of this electrode were investigated and presented. Good dimensional stability and active material adherence have been demonstrated in electrodes made from this lightweight plaque.

Britton, Doris L.↗

NASA NTRS2023

Damage Tolerance Comparison of IM7/8552 and T1100/3960 Carbon Fiber/Epoxy Sandwich Structure in Support of the Space Launch System Payload Adapter Fitting

As technology evolves and improves within the science of composite materials, new fiber/ resin systems are being developed for improved properties given certain loading and environmental scenarios. Improving the room temperature damage tolerance capabilities has long been one of the goals in the carbon fiber/polymer composite industry. Recently a new fiber/epoxy system has been introduced that is claimed to have superior damage tolerance capabilities. To examine if this new carbon fiber/epoxy composite material would be of benefit to a program to manufacture a Payload Adapter Fitting (PAF) for NASA’s Space Launch System (SLS) rocket, the question was asked as to just how much damage tolerance could be realized if this new system were used. Compression after impact (CAI) strength of sandwich structure is one of the leading metrics being used to evaluate materials for the PAF program. As a result, a comparison of this new fiber/resin system with a very common (and planned baseline) fiber/resin system with respect to CAI was considered in this study. While it was already known that the older, baseline carbon fiber structure would not have as good damage tolerance characteristics as the newer carbon fiber system, the quantitative difference in damage tolerance was sought in this study since no other CAI data could be found in open literature on sandwich structures made with this new fiber/resin system.

A.T. Nettles↗

NASA NTRS2019

Fracture Control for Additively Manufactured Spacecraft Structures

This paper describes how the intent of current NASA fracture control requirements may be applied to “fracture critical” additively manufactured spacecraft hardware. Fracture control is a multi-discipline design and certification methodology that is applied in order to mitigate catastrophic failure of structures resulting from growth of an undetected crack-like defect. The methodology is defined in existing NASA standards and is required on all human-rated space structures. As legacy spacecraft structures have been built using primarily metallic and composite materials manufactured using well established methods, guidance for application of fracture control to parts composed of these material types has been established and is documented in several NASA requirements. Additive manufactured structures offer advantages in design flexibility and manufacturing efficiency and as a result are expected to continue to be used more and more in the future. Recently, relevant guidance has been published by NASA to define materials and processes requirements for certain additive manufactured hardware, but procedures for fracture control are not addressed yet in any requirements or guidance document. While use of additive manufactured parts in non-critical scenarios may be of relatively low concern in current structural certification processes, there is a need for new fracture control guidance in order to use and certify additively manufacture hardware that is “fracture critical” where failure of the part may result in loss of life or loss of vehicle. Assurance of damage tolerance, i.e., that as-built flaws in a given part either do not exist or will not grow to become catastrophic, is of particular interest to the fracture control community. This poses a challenge due to the fact that damage tolerance behavior is not well understood in additive manufactured parts compared to legacy material types and manufacturing techniques. The discussion contained herein is necessary at this time as new guidance in this area should be founded collaboratively by the technical community at large. Different hardware types (e.g., pressure vessel, structural member) are described to highlight specific challenges and solutions for each. The discussion concludes with considering specific disciplines within fracture control (non-destructive evaluation, materials & processes, fracture mechanics, and structural certification) in a proposed extension of existing fracture control requirements to additive manufactured parts.

McElroy, Mark↗

NASA NTRS2019

Fracture Control for Additive Manufactured Spacecraft Structures

This paper describes how the intent of current NASA fracture control requirements may be applied to “fracture critical” additively manufactured spacecraft hardware. Fracture control is a multi-discipline design and certification methodology that is applied in order to mitigate catastrophic failure of structures resulting from growth of an undetected crack-like defect. The methodology is defined in existing NASA standards and is required on all human-rated space structures. As legacy spacecraft structures have been built using primarily metallic and composite materials manufactured using well established methods, guidance for application of fracture control to parts composed of these material types has been established and is documented in several NASA requirements. Additive manufactured structures offer advantages in design flexibility and manufacturing efficiency and as a result are expected to continue to be used more and more in the future. Recently, relevant guidance has been published by NASA to define materials and processes requirements for certain additive manufactured hardware, but procedures for fracture control are not addressed yet in any requirements or guidance document. While use of additive manufactured parts in non-critical scenarios may be of relatively low concern in current structural certification processes, there is a need for new fracture control guidance in order to use and certify additively manufacture hardware that is “fracture critical” where failure of the part may result in loss of life or loss of vehicle. Assurance of damage tolerance, i.e., that as-built flaws in a given part either do not exist or will not grow to become catastrophic, is of particular interest to the fracture control community. This poses a challenge due to the fact that damage tolerance behavior is not well understood in additive manufactured parts compared to legacy material types and manufacturing techniques. The discussion contained herein is necessary at this time as new guidance in this area should be founded collaboratively by the technical community at large. Different hardware types (e.g., pressure vessel, structural member) are described to highlight specific challenges and solutions for each. The discussion concludes with considering specific disciplines within fracture control (non-destructive evaluation, materials & processes, fracture mechanics, and structural certification) in a proposed extension of existing fracture control requirements to additive manufactured parts.

McElroy, Mark↗

NASA NTRS2003

Overview of NASA GRC Stirling Technology Development

The Stirling Radioisotope Generator (SRG) is currently being developed by Lockheed Martin Astronautics (LMA) under contract to the Depar1ment of Energy (DOE). The generator will be a high efficiency electric power source for NASA Space Science missions with the capability to operate in the vacuum of deep space or in an atmosphere such as on the surface of Mars. High system efficiency is obtained through the use of free-piston Stirling power conversion technology. Power output of the generator will be greater than 100 watts at the beginning of life with the decline in power being largely due to the decay of the plutonium heat source. In suppOl1 of the DOE SRG project, the NASA Glenn Research Center (GRC) has established a near-term technology effort to provide some of the critical data to ensure a successful transition to flight for what will be the first dynamic power system used in space. Initially, a limited number of technical areas were selected for the GRC effort, however this is now being expanded to more thoroughly cover a range of technical issues. The tasks include in-house testing of Stirling convertors and controllers, materials evaluation and heater head life assessment, structural dynamics, electromagnetic interference, organics evaluation, and reliability analysis. Most of these high-level tasks have several subtasks within. There is also an advanced technology effort that is complementary near-term technology effort. Many of the tests make use of the 55-We Technology Demonstration Convel10r (TDC). There have been multiple controller tests to support the LMA flight controller design effort. Preparation is continuing for a thermal/vacuum system demonstration. A pair of flight prototype TDC's have recently been placed on an extended test with unattended, continuous operation. Heater head life assessment efforts continue, with the material data being refined and the analysis moving toward the system perspective. Long-term magnet aging tests are continuing to characterize any possible aging in the strength or demagnetization resistance of the permanent magnets used in the linear alternator. In a parallel effort, higher performance magnets are also being evaluated. A reliability effort is being initiated that will help to guide the development activities with an increased focus on the necessary components and subsystems. Some other disciplines that are active in the GRC technology effort include structural dynamics, linear alternator analysis, EMI/EMC, controls, and mechanical design evaluation. This paper will provide an overview of some of the GRC technical efforts, including the current status, and a description of future efforts.

Schreiber, Jeffrey↗

NASA NTRS2016

Improved ASTM G72 Test Method for Ensuring Adequate Fuel-to-Oxidizer Ratios

The ASTM G72/G72M-15 Standard Test Method for Autogenous Ignition Temperature of Liquids and Solids in a High-Pressure Oxygen-Enriched Environment is currently used to evaluate materials for the ignition susceptibility driven by exposure to external heat in an enriched oxygen environment. Testing performed on highly volatile liquids such as cleaning solvents has proven problematic due to inconsistent test results (non-ignitions). Non-ignition results can be misinterpreted as favorable oxygen compatibility, although they are more likely associated with inadequate fuel-to-oxidizer ratios. Forced evaporation during purging and inadequate sample size were identified as two potential causes for inadequate available sample material during testing. In an effort to maintain adequate fuel-to-oxidizer ratios within the reaction vessel during test, several parameters were considered, including sample size, pretest sample chilling, pretest purging, and test pressure. Tests on a variety of solvents exhibiting a range of volatilities are presented in this paper. A proposed improvement to the standard test protocol as a result of this evaluation is also presented. Execution of the final proposed improved test protocol outlines an incremental step method of determining optimal conditions using increased sample sizes while considering test system safety limits. The proposed improved test method increases confidence in results obtained by utilizing the ASTM G72 autogenous ignition temperature test method and can aid in the oxygen compatibility assessment of highly volatile liquids and other conditions that may lead to false non-ignition results.

Juarez, Alfredo↗

NASA NTRS2016

Improved ASTM G72 Test Method for Ensuring Adequate Fuel-to-Oxidizer Ratios

The ASTM G72/G72M-15 Standard Test Method for Autogenous Ignition Temperature of Liquids and Solids in a High-Pressure Oxygen-Enriched Environment is currently used to evaluate materials for the ignition susceptibility driven by exposure to external heat in an enriched oxygen environment. Testing performed on highly volatile liquids such as cleaning solvents has proven problematic due to inconsistent test results (non-ignitions). Non-ignition results can be misinterpreted as favorable oxygen compatibility, although they are more likely associated with inadequate fuel-to-oxidizer ratios. Forced evaporation during purging and inadequate sample size were identified as two potential causes for inadequate available sample material during testing. In an effort to maintain adequate fuel-to-oxidizer ratios within the reaction vessel during test, several parameters were considered, including sample size, pretest sample chilling, pretest purging, and test pressure. Tests on a variety of solvents exhibiting a range of volatilities are presented in this paper. A proposed improvement to the standard test protocol as a result of this evaluation is also presented. Execution of the final proposed improved test protocol outlines an incremental step method of determining optimal conditions using increased sample sizes while considering test system safety limits. The proposed improved test method increases confidence in results obtained by utilizing the ASTM G72 autogenous ignition temperature test method and can aid in the oxygen compatibility assessment of highly volatile liquids and other conditions that may lead to false non-ignition results.

Juarez, Alfredo↗

NASA NTRS1981

Silicon solar cell process development, fabrication and analysis

The fabrication of solar cells from several unconventional silicon materials is described, and cell performance measured and analyzed. Unconventional materials evaluated are edge defined film fed grown (EFG), heat exchanger method (HEM), dendritic web grown, and continuous CZ silicons. Resistivity, current voltage, and spectral sensitivity of the cells were measured. Current voltage was measured under AM0 and AM1 conditions. Maximum conversion efficiencies of cells fabricated from these and other unconventional silicons were compared and test results analyzed. The HEM and continuous CZ silicon were found to be superior to silicon materials considered previously.

Minahan, J. A.↗

NASA NTRS2005

Nondestructive Evaluation of Advanced Materials with X-ray Phase Mapping

X-ray radiation has been widely used for imaging applications since Rontgen first discovered X-rays over a century ago. Its large penetration depth makes it ideal for the nondestructive visualization of the internal structure and/or defects of materials unobtainable otherwise. Currently used nondestructive evaluation (NDE) tools, X-ray radiography and tomography, are absorption-based, and work well in heavy-element materials where density or composition variations due to internal structure or defects are high enough to produce appreciable absorption contrast. However, in many cases where materials are light-weight and/or composites that have similar mass absorption coefficients, the conventional absorption-based X-ray methods for NDE become less useful. Indeed, the light-weight and ultra-high-strength requirements for the most advanced materials used or developed for current flight mission and future space exploration pose a great challenge to the standard NDE tools in that the absorption contrast arising from the internal structure of these materials is often too weak to be resolved. In this presentation, a solution to the problem, the use of phase information of X-rays for phase contrast X-ray imaging, will be discussed, along with a comparison between the absorption-based and phase-contrast imaging methods. Latest results on phase contrast X-ray imaging of lightweight Space Shuttle foam in 2D and 3D will be presented, demonstrating new opportunities to solve the challenging issues encountered in advanced materials development and processing.

Hu, Zhengwei↗

NASA NTRS1973

Design and analysis of the radiator structure for space power systems

The design, analysis, fabrication, and development of the 5-kWe radiator structure are shown. Thermal performance, meteoroid protection, structural capability during launch, development testing and space operation, material evaluation, and the configuration selection are described. The fin-tube development program depends on the relative values of the thermal coefficients of expansion. The initial selection of aluminum fins and Type 316 stainless-steel tubes was based on previous experience; however, the large differential in their expansion rates showed that an alternate, more compatible, combination was needed. Copper, stainless-steel-clad copper, boron-impregnated aluminum, and an independent radiator with a titanium structure were all considered as alternate materials. The final selection was Lockalloy fins with Type 304 stainless-steel D tubes.

Dauterman, W. H.↗

NASA NTRS1971

Vacuum and ultraviolet radiation effects on binders and pigments for spacecraft thermal control coatings

An evaluation of several silicone resin binders and powdered inorganic pigments for potential use in spacecraft thermal-control paint formulations is presented. The pigments were selected on the basis of a hypothesis relating the heat of formation of a compound to the compound's resistance to ultra-radiation-induced degradation. Reflectance measurements were made in situ to determine degradation rates due to ultraviolet radiation. The tested polydimethylsiloxane resins were not significantly affected by long exposures to ultraviolet radiation. All the pigments, which were dispersed in a polydimethylsiloxane resin, were degraded by ultraviolet radiation as determined by an increase of solar absorptance. For the materials evaluated in this study, no evidence was found to indicate that pigments with high heats of formation were resistant to ultraviolet degradation.

Progar, D. J.↗

NASA NTRS1973

Design, process development, manufacture, test and evaluation of boron-aluminum for space shuttle components

A multi phase boron-aluminum design and evaluation program for space shuttle components was conducted, culminating in the fabrication of a 1.22 m (48 inch) x 1.83 m (72 inch) boron-aluminum compression panel capable of distributing a point load of 1555 kN (350,000 lbs) into a uniform running load at a temperature of 589 K (600 F). This panel was of the skin-stringer construction with two intermediate frame supports; seven unidirectional stringers varied in thickness from 5 plies to 52 plies and the skin was contoured to thicknesses ranging from 10 plies to 62 plies. Both the stringers and the skin incorporated Ti-6Al-4V titanium interleaves to increase bearing and in-plane shear strength. The discrete program phases were materials evaluation, design studies, process technology development, fabrication and assembly, and test and evaluation.

Garrett, R. A.↗

NASA NTRS1973

Magnetic materials selection for static inverter and converter transformers

A program to study magnetic materials is described for use in spacecraft transformers used in static inverters, converters, and transformer-rectifier supplies. Different magnetic alloys best suited for high-frequency and high-efficiency applications were comparatively investigated together with an investigation of each alloy's inherent characteristics. The materials evaluated were the magnetic alloys: (1) 50% Ni, 50% Fe; (2) 79% Ni, 17% Fe, 4% Mo; (3) 48% Ni, 52% Fe; (4) 78% Ni, 17% Fe, 5% Mo; and (5) 3% Si, 97% Fe. Investigations led to the design of a transformer with a very low residual flux. Tests were performed to determine the dc and ac magnetic properties at 2400 Hz using square-wave excitation. These tests were performed on uncut cores, which were then cut for comparison of the gapped and ungapped magnetic properties. When the data of many transformers in many configurations were compiled the optimum transformer was found to be that with the lowest residual flux and a small amount of air gap in the magnetic material. The data obtained from these tests are described, and the potential uses for the materials are discussed.

Mclyman, W. T.↗