Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “loss factor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Optimization of Dimensions of Smooth and Twisted-Tape-Inserted Tubes for Heat Transfer with NaCl/KCl/MgCl 2 Molten Salts by Principle of Entropy Generation Minimization

The entropy generation minimization principle is used as the criterion to optimize the flow and heat transfer of solar collectors and heat exchangers that use molten salts NaCl–KCl–MgCl 2 and KCl–MgCl 2 . The Gnielinski correlation for the Nusselt number versus Reynolds number, as well as the Moody friction factor given by Petukhov, was used for the calculation of the convective heat transfer coefficient and pressure loss due to friction in smooth tubes. For twisted-tap-inserted tube, equations of Nu and friction factor provided by Manglik and Bergles were used. The objective function, the entropy generation rate of the heat transfer system, was expressed as the function of Reynolds number, Prandtl number, heating flux, tube diameter, etc. As a result of the analysis, the optimum Reynolds number was determined and thereby to determine the optimum Nusselt number, convective heat transfer coefficient, friction factor, and tube diameter, which also allows the calculation of optimum flow velocity. The analysis was conducted in the fluid temperature range of 500–700 °C, which covers the operation temperature for supercritical CO 2 power cycles in concentrated solar power (CSP) system. Here, optimized results from the smooth tube and twisted-tap-inserted tube are compared, which is important to the design of solar receivers for CSP systems.

14 SOLAR ENERGY↗
DOE OSTI2021

Loss channels affecting lithium niobate phononic crystal resonators at cryogenic temperature

Here, we investigate the performance of microwave-frequency phononic crystal resonators fabricated on thin-film lithium niobate for integration with superconducting quantum circuits. For different design geometries at millikelvin temperatures, we achieve mechanical internal quality factors Qi above 10 5 –10 6 at high microwave drive power, corresponding to 5×10 6 phonons inside the resonator. By sweeping the defect size of resonators with identical mirror cell designs, we are able to indirectly observe signatures of the complete phononic bandgap via the resonators' internal quality factors. Examination of quality factors' temperature dependence shows how superconducting and two-level system (TLS) loss channels impact device performance. Finally, we observe an anomalous low-temperature frequency shift consistent with resonant TLS decay and find that the material choice can help to mitigate these losses.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Combining variational autoencoders and physical bias for improved microscopy data analysis *

Electron and scanning probe microscopy produce vast amounts of data in the form of images or hyperspectral data, such as electron energy loss spectroscopy or 4D scanning transmission electron microscope, that contain information on a wide range of structural, physical, and chemical properties of materials. To extract valuable insights from these data, it is crucial to identify physically separate regions in the data, such as phases, ferroic variants, and boundaries between them. In order to derive an easily interpretable feature analysis, combining with well-defined boundaries in a principled and unsupervised manner, here we present a physics augmented machine learning method which combines the capability of variational autoencoders to disentangle factors of variability within the data and the physics driven loss function that seeks to minimize the total length of the discontinuities in images corresponding to latent representations. Our method is applied to various materials, including NiO-LSMO, BiFeO 3 , and graphene. The results demonstrate the effectiveness of our approach in extracting meaningful information from large volumes of imaging data. The customized codes of the required functions and classes to develop phyVAE is available at https://github.com/arpanbiswas52/phy-VAE.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Ants disperse seeds farther in habitat patches with corridors

Habitat fragmentation impacts ecosystems worldwide through habitat loss, reduced connectivity, and edge effects. Yet, these landscape factors are often confounded, leaving much to be investigated about their relative effects, especially on species interactions. In a landscape experiment, we investigated the consequences of connectivity and edge effects for seed dispersal by ants. We found that ants dispersed seeds farther in habitat patches connected by corridors, but only in patch centers. We did not see an effect on the total number of seeds moved or the rate ants detected seeds. Furthermore, we did not see any differences in ant community composition across patch types, suggesting that shifts in ant behavior or other factors increased ant seed dispersal in patches connected by corridors. Long-distance seed dispersal by ants that requires an accumulation of short-distance dispersal events over generations may be an underappreciated mechanism through which corridors increase plant diversity.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2024

Feasibility of using crystal channeling for the beam loss mitigation in slow extraction at 8GeV

In the accelerator applications of slow extraction for High Energy Physics (HEP), one of the prime challenges is the mitigation of beam losses, which is becoming increasingly critical with the continuous rise in beam power. A significant breakthrough was achieved earlier at CERN through the successful deployment of proton beam channeling in a crystal at 400GeV, effectively diverting the beam away from extraction septa and offering new avenues for improving slow extraction efficiency. However, a crucial question remains whether this approach is still effective at lower and medium proton beam energies. In this paper, we present the promising results of the computer simulation studies of the septum shadowing at 8GeV for the Mu2e project slow extraction at Fermilab. In conclusion, across the wide range of beam parameters, the beam loss reduction is shown to range between 40% and factor of three.

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

An IRE1-proteasome system signalling cohort controls cell fate determination in unresolved proteotoxic stress of the plant endoplasmic reticulum

Excessive accumulation of misfolded proteins in the endoplasmic reticulum (ER) causes ER stress, which is an underlying cause of major crop losses and devastating human conditions. Here, ER proteostasis surveillance is mediated by the conserved master regulator of the unfolded protein response (UPR), Inositol Requiring Enzyme 1 (IRE1), which determines cell fate by controlling pro-life and pro-death outcomes through as yet largely unknown mechanisms. Here we report that Arabidopsis IRE1 determines cell fate in ER stress by balancing the ubiquitin–proteasome system (UPS) and UPR through the plant-unique E3 ligase, PHOSPHATASE TYPE 2CA (PP2CA)-INTERACTING RING FINGER PROTEIN 1 (PIR1). Indeed, PIR1 loss leads to suppression of pro-death UPS and the lethal phenotype of an IRE1 loss-of-function mutant in unresolved ER stress in addition to activating pro-survival UPR. Specifically, in ER stress, PIR1 loss stabilizes ABI5, a basic leucine zipper (bZIP) transcription factor, that directly activates expression of the critical UPR regulator gene, bZIP60, triggering transcriptional cascades enhancing pro-survival UPR. Collectively, our results identify new cell fate effectors in plant ER stress by showing that IRE1’s coordination of cell death and survival hinges on PIR1, a key pro-death component of the UPS, which controls ABI5, a pro-survival transcriptional activator of bZIP60.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Time dependent model for non-inductive ECH X-I current ramp-up for SHPD tokamak facility

Non-inductive (NI) plasma current start-up and ramp-up is an important research topic for spherical tokamak (ST) based reactors and fusion pilot plant (FPP). For a compact FPP, the OH flux availability is highly restricted due to its compact geometry. Efficient fundamental extraordinary mode (X-I) electron cyclotron heating (ECH) current start-up and ramp-up regime was identified for a reactor-like high toroidal magnetic field range which has more than a hundred times higher current drive efficiency compared to more conventional ECH methods for the relevant start-up temperature range. High current drive efficiency is possible due to the strong X-I fundamental ECH interaction only with unidirectional passing electrons constrained by the wave accessibility conditions. Here, we extend the X-I electron cyclotron current drive (ECCD) investigation to a time dependent model to simulate the non-inductive current ramp-up to 10 MA for the Sustained High-Power Density (SHPD) facility. As the X-I ECCD driven current I EC rises, due to the back EMF driven negative current, the net plasma current Ip rises more slowly with the current resistive time scale. For tokamak confinement time (both L-mode and H-Mode) which tends to rise with I p , a positive feedback results and even with constant applied ECH power, T e0 , I EC , and I p can continue to rise to very high values. However, in a realistic situation, the T e0 rise should saturate due to a number of factors such as enhanced core radiation and increased power loss at high temperature. To simulate this effect, we adopt a maximum T e0 model which would limit the temperature rise to certain T e0 . With this model, we investigated the current ramp-up for various ECH power levels and the maximum T e0 of 15, 20, and 25 keV. We find that while the power required is reduced with increasing T e0 limit due to increased current drive efficiency, the time to reach 10 MA tends to go up due to the reduced plasma resistivity for the higher T e0 limit. We also find for a given Te0 limit, the time to reach 10 MA tends to be reduced by increasing the applied ECH power by over driving the current ramp-up where I EC is driven at significantly higher level than 10 MA. While the current ramp-up time may not be an issue for the steady-state reactor systems, if it is desirable to minimize the current ramp-up time, it is prudent to have a sufficient ECH power for current over-drive and have some T e0 limiting tools such as impurity seeding for enhanced radiation. In conclusion, a well-controlled NI ECH start-up also has a potential of improving the tokamak start-up reliability and avoid run-away electrons while the NI off-axis current drive could enhance MHD stability and plasma performance improvements.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

High-performance plasmas after pellet injections in Wendelstein 7-X

A significant improvement of plasma parameters in the optimized stellarator W7-X is found after injections of frozen hydrogen pellets. The ion temperature in the post-pellet phase exceeds 3 keV with 5 MW of electron heating and the global energy confinement time surpasses the empirical ISS04-scaling. The plasma parameters realized in such experiments are significantly above those in comparable gas-fuelled discharges. Here, we present details of these pellet experiments and discuss the main plasma properties during the enhanced confinement phases. Local power balance is applied to show that the heat transport in post-pellet phases is close to the neoclassical level for the ion channel and is about a factor of two above that level for the combined losses. In comparable gas-fuelled discharges, the heat transport is by about ten times larger than the neoclassical level, and thus is largely anomalous. It is further observed that the improvement in the transport is related to the peaked density profiles that lead to a stabilization of the ion-scale turbulence.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Quantum state preparation by adiabatic evolution with custom gates

Quantum state preparation by adiabatic evolution is currently rendered ineffective by the long implementation times of the underlying quantum circuits, comparable to the decoherence time of present and near-term quantum devices. These implementation times can be significantly reduced by realizing these circuits with custom gates. Using classical computing, we model the output of a realistic two-qubit processor implementing the adiabatic evolution of a two-spin system by means of custom gates. This modeled output is then compared with the results of quantum simulations solving the same problem on IBM Quantum (IBMQ) systems. Additionally, when used to emulate the behavior of the IBMQ quantum circuit, our realistic model yields state fidelities ranging from 65% to 85%, similar to the actual performance of a diverse set of IBMQ devices. When we reduced the implementation time by using custom gates, however, the loss of fidelity was reduced by at least a factor of 4, allowing us to accurately extract the energy of the target state. This improvement is enough to render adiabatic evolution useful for quantum state preparation for small systems or as a preconditioner for other state preparation methods.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Focusing transformers/filters in isotropic/anisotropic piezoelectrics

A focusing interdigital transducer (IDT) and corresponding single- and dual-port piezoelectric devices are disclosed. The focusing interdigital transducer, which generates Lamé acoustic waves, permits operation at significantly higher frequencies than those possible with traditional IDTs. The focusing IDT employs multiple arced fingers formed both above and below the piezoelectric layer to improve coupling efficiency by coupling through both the e31 and e33 piezoelectric coefficients to the piezoelectric layer. By optimizing both anchor design and location, acoustic wave losses are minimized, thereby improving the device's quality factor Q. Through proper bus design and selection of the number of IDT fingers, a device's impedance can be tuned for a given application. The focusing IDTs may be used in single-port filter devices and dual-port transformer devices. The single- and dual-port devices may operate at a single frequency, at two frequencies, or over a band of frequencies.

Siddiqui, Aleem↗
DOE OSTI2025

High-Quality Factor Microwave Resonators using Rhenium

Coplanar waveguide resonators are a perfect tool to evaluate the losses induced by defects and interfaces in superconducting devices. Even if niobium is the most used superconductor for resonators and qubits, its native oxide at the metal-air (MA) interface limits the device results. Tantalum has recently significantly improved qubit performances due to a thinner and less disordered oxide layer compared to Nb. To further improve the MA interface, we used rhenium, a superconducting material with 1.7 K critical temperature resistant to oxidation: it forms an oxide layer thinner than 1 nm. In this study, we will present a thorough investigation of rhenium CPW resonator measurements with internal quality factors at the single photon level exceeding 2 million. The devices have been fabricated on a sapphire substrate while the processing parameters have been varying and optimized. The measurements have been performed as a function of power and temperature to disentangle different sources of losses, such as two-level systems (TLS) and quasi-particles. A peculiar TLS temperature dependence has been measured and analyzed. In this work, we also vary the participation ratio of the devices to extract the losses introduced by the involved interfaces with higher fidelity and precision. We carried on a deep material characterization effort to link the results to the differences in the fabrication steps, and we will present material characterization measurements performed via AFM, ToF-SIMS, XPS, and TEM.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Unraveling Hydrogen Induced Geochemical Reaction Mechanisms through Coupled Geochemical Modeling and Machine Learning

Underground hydrogen storage (UHS) provides a promising large-scale, long-term energy storage solution. A reasonable recovery of stored hydrogen is critical for a successful storage scheme. However, in subsurface reservoirs hydrogen is subject to active geochemical reactions that might result in hydrogen loss. In this study, we implemented a geochemical modeling approach coupled with an unsupervised machine learning technique called non-negative matrix factorization (NMF) to unravel the complex brine-rock-H 2 geochemical processes responsible for hydrogen losses, with particular focus on sulfate reduction reactions. NMF is applied to modeled mineral evolution and fluid component profiles to retrieve profiles that can be interpreted to more easily assess competing processes. NMF decouples simulated competing equilibrium reactions. This facilitates separation of overlapping reaction profiles from redox processes, dissolution fronts, and secondary precipitation while considering the effects of simulation parameters such as salinity, temperature, and total H 2 pressure. NMF successfully discriminates these competing effects in nonlinear ways, allowing robust interpretation. In addition, NMF reveals subtle coupled mineral associations and reaction fronts that are invisible to conventional model analysis. This integrated approach strengthens the conceptual understanding of complex nonlinear hydrogen-brine-rock interactions and advances geochemical research on UHS systems to resolve complexities in modeled geochemical systems without the need for direct experiments or prior knowledge. Furthermore, this study highlights the efficacy of combining geochemical modeling with machine learning techniques to enhance the interpretability of the intricate geochemical simulation output through deciphering the overlapping reaction path that cannot be achieved only using conventional analysis of geochemical models alone.

08 HYDROGEN↗
DOE OSTI2021

A two-dimensional analytical unit cell model for redox flow battery evaluation and optimization

Cell performance optimization is important for improving the overall system efficiency of a redox flow battery. To gain better insights into key controlling factors of system efficiency, this work first proposed a theoretical model for a unit flow battery cell by extending a two-dimensional analytic model to a full battery cell. Such a model is then used for cell performance optimization after validating it with experimental and numerical modeling data. With the model results, the activation, equilibrium, and pump energy losses are identified as the dominant sources of battery energy losses. Further, a guideline for reducing these sources is also proposed. Following the guideline, the mass transport coefficient is shown as a key control factor of the equilibrium energy loss and Coulombic efficiency (CE). Approaches are then proposed to improve CE and the overall system efficiency. The mass transport is also revealed as the mechanism of pump rate optimization where an optimal pump rate significantly reduces the equilibrium energy loss. With both low equilibrium and pump energy losses, an optimal electrode porosity or specific area design can further improve a battery's system efficiency based on an optimal porosity predicted by the present model. The model also demonstrates distinct behaviors and overestimation in the system efficiency when reduced to a zero-dimensional model with neglected mass transport resistance. With the new model, the guideline, and new insights, this work provides a reliable and efficient tool for the evaluation and optimization of redox flow battery design in practical applications.

25 ENERGY STORAGE↗
DOE OSTI2023

Hollow Ptychography: Toward Simultaneous 4D Scanning Transmission Electron Microscopy and Electron Energy Loss Spectroscopy

With the recent development of high-acquisition-speed pixelated detectors, 4D scanning transmission electron microscopy (4D-STEM) is becoming routinely available in high-resolution electron microscopy. 4D-STEM acts as a “universal” method that provides local information on materials that is challenging to extract from bulk techniques. It extends conventional STEM imaging to include super-resolution techniques and to provide quantitative phase-based information, such as differential phase contrast, ptychography, or Bloch wave phase retrieval. However, an important missing factor is the chemical and bonding information provided by electron energy loss spectroscopy (EELS). 4D-STEM and EELS cannot currently be acquired simultaneously due to the overlapping geometry of the detectors. Here, the feasibility of modifying the detector geometry to overcome this challenge for bulk specimens is demonstrated, and the use of a partial or defective detector for ptycholgaphic structural imaging is explored. Here, results show that structural information beyond the diffraction-limit and chemical information from the material can be extracted together, resulting in simultaneous multi-modal measurements, adding the additional dimensions of spectral information to 4D datasets.

4D-scanning transmitting electron microscopy (STEM↗
DOE OSTI2022

Donor End-Capped Alkyl Chain Length Dependent Non-Radiative Energy Loss in All-Small-Molecule Organic Solar Cells

A critical bottleneck for further efficiency breakthroughs in organic solar cells (OSCs) is to minimize the non-radiative energy loss (eΔV nr ) while maximizing the charge generation. With the development of highly emissive low-bandgap non-fullerene acceptors, the design of high-performance donors becomes critical to enable the blend with the electroluminescence quantum efficiency to approach or surpass the pristine acceptor. Herein, by shortening the end-capped alkyl chains of the small-molecular donors from hexyl (MPhS-C6) to ethyl (MPhS-C2), the material obtained aggregation that was insensitive to thermal annealing (TA) along with condensed packing simultaneously. The former leads to small phase separation and suppressed upshifts of the highest occupied molecular orbital energy level during TA, and the latter facilitates its efficient charge-transport at aggregation-less packing. Hence, the ΔV nr decreases from 0.242 to 0.182 V, from MPhS-C6 to MPhS-C2 based OSCs. An excellent PCE of 17.11% is obtained by 1,8-diiodoctane addition due to almost unchanged high J sc (26.6 mA cm –2 ) and V oc (0.888 V) with improved fill factor, which is the record efficiency with the smallest energy loss (0.497 eV) and ΔV nr (0.192 V) in all-small-molecule OSCs. Finally, these results emphasize the potential material design direction of obtaining concurrent TA-insensitive aggregation and condensed packing to maximize the device performances with a super low ΔV nr .

36 MATERIALS SCIENCE↗
DOE OSTI2024

Superconducting microwave cavities and qubits for quantum information systems

Superconducting microwave cavities featuring ultrahigh Q-factors, which measure the efficiency of energy storage in relation to energy loss in a system, are revolutionizing quantum computing by providing long coherence times exceeding 1 ms, crucial for the development of scalable multi-qubit quantum systems with low error rates. Here, in this work, we provide an in-depth analysis of recent advances in ultrahigh Q-factor cavities, integration of Josephson junction-based qubits, and bosonic-encoded qubits in 3D cavities. We examine the sources of quantum state dephasing caused by damping and noise mechanisms in cavities and qubits, highlighting the critical challenges that need to be addressed to achieve even higher coherence times. We critically survey the latest progress made in implementing single 3D qubits using superconducting materials, normal metals, and multi-qubit and multi-state quantum systems. Our work sheds light on the promising future of this research area, including novel materials for cavities and qubits, modes with nontrivial topological properties, error correction techniques for bosonic qubits, and new light–matter interaction effects.

3D printing↗
DOE OSTI2025

Subventricular Accumulation of Cu in the Aging Mouse Brain Does Not Associate with Anticipated Increases in Markers of Oxidative Stress

Natural aging is associated with mild memory loss and cognitive decline, and age is the greatest risk factor for neurodegenerative diseases, such as Alzheimer’s disease. There is substantial evidence that oxidative stress is a major contributor to both natural aging and neurodegenerative disease, and coincidently, levels of redox active metals such as Fe and Cu are known to be elevated later in life. Recently, a pronounced age-related increase in Cu content has been reported to occur in mice and rats around a vital regulatory brain region, the subventricular zone of lateral ventricles. In our study herein, we have characterized lateral ventricle Cu content in a unique murine model of accelerated aging, senescence accelerated mouse-prone 8 (SAMP8) mice. Our results confirm an age-related increase in ventricle Cu content, consistent with the studies by others in wild-type mice and rats. Specifically, we observed Cu content to increase over the time frame 1 to 5 months and 5 to 9 months, but interestingly, no significant increase occurred between 9 and 12 months (although brain Cu content at 12 months was significantly elevated relative to 1 and 5 month-old animals). Despite the magnitude of Cu increase observed within the cells that comprise the subventricular zone of lateral ventricles (average 3 mM Cu, with isolated subcellular concentrations of 17 mM), we did not detect spectroscopic markers of thiol oxidation, protein aggregation, or lipid oxidation. The lack of evidence for oxidative stress in ex vivo animal tissue is in contrast to in vitro studies demonstrating that thiol, protein, and lipid oxidation is pronounced at these Cu concentrations. We suggest that our findings most likely indicate that the Cu ions in this brain region are sequestered in an unreactive form, possibly extended chains of Cu-thiolate complexes, which do not readily redox cycle in the aqueous cytosol. In conclusion, these results also appear to partially challenge the long-held view that age-related increases in brain metal content drive oxidative stress as we did not observe a concomitant association between age-related Cu increase and markers of oxidative stress, nor did we observe a net increase in Cu content between mice aged 9 and 12 months.

X-ray fluorescence↗
DOE OSTI2024

The Relative Importance of Antarctic Sea Ice Loss within the Response to Greenhouse Warming

Abstract The response to Antarctic sea ice loss within a coupled modeling framework is examined in comparison to the response to Arctic sea ice loss and within the context of general greenhouse warming. Sea ice loss responses are found to be linear (particularly in response to Antarctic or global sea ice loss) with respect to the degree of imposed perturbation and additive when perturbations are applied in hemispheres separately and concurrently. Globally, and in the tropical Pacific in particular, Antarctic sea ice loss plays a relatively larger role than Arctic sea ice loss in both the atmosphere and the ocean, within the parameters of our experiments. The pattern of response to Antarctic sea ice loss is also found to more closely resemble that of greenhouse warming, again particularly in the tropics. An extension to multiparameter pattern scaling is developed to include a scaling factor for Antarctic change in addition to those for tropical warming and Arctic sea ice loss. The decomposition is applied to the modeled response to Antarctic sea ice loss to break it down into component partial responses that scale with Antarctic, tropical, and Arctic changes. This reveals the aspects of the response that are directly related to Antarctic change, such as an equatorward intensification of tropical precipitation in the Northern Hemisphere, and those that are modified via the induced changes in the tropics and Arctic, such as Northern Hemisphere temperature change. With this, we hope to gain a deeper understanding of the role of each of these changes for the development of physical mechanisms of the response.

Meteorology & Atmospheric Sciences↗