SEARCH · Engineering Papers

Results for “linear power flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Rapid Load Transition for Integrated Solid Oxide Fuel Cell - Gas Turbine (SOFC-GT) Energy Systems: A Demonstration of the Potential for Grid Response

Rapid load transition is an essential requirement for integrated energy systems to maintain grid resilience as more renewable resources are added to the grid. Integrated solid oxide fuel cell - gas turbine (SOFC-GT) systems can provide high efficiency and low carbon emissions over a broad range of turndown. These hybrids also have the potential to enable rapid grid response. The challenge has been to demonstrate effective control strategies to manage load transitions. In the present study, a load transition of ~50% was achieved in 10 s using a novel but simple strategy. Power demand on the SOFC and the GT were ramped down concurrently. During this transition, the SOFC anode fuel was manipulated to maintain SOFC fuel utilization while the cathode inlet air flow and temperature were also manipulated to thermally protect the SOFC. This study was conducted using the Hybrid Performance (Hyper) facility at the National Energy Technology Laboratory (NETL) in a co-simulation environment with the Idaho National Laboratory (INL)'s grid-simulation. The load ramping strategy was tested using a hardware-based cyber-physical simulation methodology. The results demonstrate a high-fidelity representation of SOFC-GT hybrid dynamics and validation of the control strategy. Thermal and electrochemical transients indicated that the SOFC was well protected during rapid load turndown without violating operability constraints. This demonstration revealed the non-linear nature of tightly coupled SOFC-GT system components, especially the non-linear response of SOFC cathode air flow and inlet temperature controls. These results highlight the needs and challenges in developing adaptive automatic controls for autonomous rapid load transitions. This work demonstrates that SOFC-GT hybrids are a viable option to provide the fast-ramping characteristics essential to accommodate high levels of variable renewable power while maintaining grid resilience, reliability, and environmental performance. The results also demonstrate the utility of co-simulation in advancing the tightly-coupled integrated energy systems needed to meet goals for zero-carbon power generation.

DIRECT ENERGY CONVERSION,POWER TRANSMISSION AND DI↗

NASA NTRS1972

The aluminum electrode in AlCl3-alkali-halide melts.

Passivation phenomena have been observed upon cathodic and anodic polarization of the Al electrode in AlCl3-KCl-NaCl melts between 100 and 160 C. They are caused by formation of a solid salt layer at the electrode surface resulting from concentration changes upon current flow. The anodic limiting currents increased with temperature and with decreasing AlCl3 content of the melt. Current voltage curves obtained on a rotating aluminum disk showed a linear relationship between the anodic limiting current and omega to the minus 1/2 power. Upon cathodic polarization, dendrite formation occurs at the Al electrode. The activation overvoltage in AlCl3-KCl-NaCl was determined by galvanostatic current step methods. An apparent exchange current density of 270 mA/sq cm at 130 C and a double layer capacity of 40 plus or minus 10 microfarad/sq cm were measured.

Holleck, G. L.↗

NASA NTRS2020

Model Rotor Hover Performance at Low Reynolds Number

Hover performance data from four key experiments has been analyzed in detail to shed some light on model rotor hover performance at low Reynolds number. Each experiment used the simplest blade geometry. The blades were constant chord and untwisted. Three experiments used blades with the NACA 0012 airfoil from root to tip. The NACA 0015 was used in the earliest test. The four experiments provide data spanning a Reynolds number range of 136,500 to 548,700. The specific objective of this report is to ask and answer two questions: 1. Does blade aspect ratio influence hover performance or is rotor solidity the fundamental rotor geometry parameter for practical engineering purposes? ANSWER: Rotor solidity is the fundamental rotor geometry parameter for practical engineering purposes. Any effect of blade aspect ratio appears to be such a secondary variable that its effect lies within the range of experimental error. 2. Is Reynolds number a significant factor in scaling up hover performance to full-scale rotor performance? The answer is twofold. ANSWER: (a) Reynolds number effects on the increase of power with thrust do not appear to be a significant factor for practical engineering purposes, and (b) Reynolds number effects on minimum profile power at or very near zero rotor thrust could not be clearly established primarily because the low torque levels could not be accurately measured with the test equipment used. This has led to significant data scatter. A number of other observations can be made based on the analysis provided herein. For instance: 1. The test matrices used in the four key references contained far too few data points. A collective pitch variation of four or five data points is insufficient to establish experimental accuracy and data repeatability. 2. A common property of the power-versus-thrust (raised to the 3/2 exponent) graphs was that this curve was linear below the onset of blade stall. 3. The blade-to-blade interference at or near zero thrust may, in fact, be creating a turbulent flow field such that the effective Reynolds number at a blade element is considerably greater than what theories using two-dimensional (2D) airfoil properties at a blade element would calculate. 4. Definitive experiments answering the two key questions have yet to be made.

Model Rotor Hover Performance↗

NASA NTRS1988

Nature and the nonlinear evolution of electrostatic waves associated with the AMPTE solar wind releases

The nonlinear evolution of the electrostatic waves observed during the AMPTE (Active Magnetosphere Particle Tracer Explorers) solar wind releases is investigated. Previous linear studies indicate two distinct sets of instabilities may be responsible for the generation. One set consists of ion-acoustic type instabilities which are insensitive to the presence of a background magnetic field, while the other group corresponds to the modified two stream instabilities and requires the solar wind flow to be across the ambient magnetic field. To establish which set of instabilities is more viable a detailed linear Vlasov theory has been conducted by numerically solving the full electromagnetic dispersion relation. In addition both the plasma wave as well as the magnetic field measurements by the IRM (Ion Release Module) spacecraft were used to correlate the frequency and the power of the observed waves with the magnitude and the direction of the solar wind magnetic field. The results of these analyses indicate that the ion-acoustic type instabilities have growth rates that are an order of magnitude or more larger than those of the modified two stream instabilities. Results show that both the solar wind protons and the released ions may be heated and accelerated in the directions oblique to the solar wind flow velocity.

Omidi, N.↗

DOE OSTI2024

Power Analysis of an ePump Applied to the Linear Functions of an Agricultural Planter

Like many other industries, the agricultural industry has recently ex-perienced pressure to reduce vehicle emissions while improving productivity. Electric actuation is perceived as a viable solution to replace or augment hydrau-lic and mechanical actuation. However, electrification presents challenges with regards to linear functions, where hydraulic actuators have advantages in terms of compactness, tolerance to contamination and resistance to shocks. A combined electro-hydraulic actuation architecture can leverage the benefits of both electric and hydraulic actuation, while reducing the drawbacks of both approaches. This work investigates the potential of a centralized electric driven pump (ePump) system powering the pressure-controlled linear functions of an agricul-tural planter, with the goal of improving the operating point of the main supply pump. In this application, the rotary functions are hydraulically actuated, alt-hough such a solution could be applied also to electric rotary actuation. This is accomplished by setting the ePump to boost the pressure supplied by the tractor to the level required by the linear functions. An accumulator is used to stabilize the flow requirements of the linear functions, and control the pressure supplied to the actuators. Two control schemes are proposed for the regulation of the ac-cumulator pressure, one favoring an efficient operating point for the ePump, the other favoring stable steady state operation. A simulation model of the baseline system and proposed system is developed and validated using experimental data from a full-scale machine. Using the vali-dated simulation, both control architectures are then evaluated for improvement in system power consumption and dynamic requirements on the ePump to assess their effectiveness. Both systems demonstrate significant improvement in power consumption over the baseline system, with the best solution improving effi-ciency by 64%.

24 POWER TRANSMISSION AND DISTRIBUTION↗

NASA NTRS1986

Simulation of double layers in a model auroral circuit with nonlinear impedance

A reduced circuit description of the U-shaped potential structure of a discrete auroral arc, consisting of the flank transmission line plus parallel-electric-field region, is used to provide the boundary condition for one-dimensional simulations of the double-layer evolution. The model yields asymptotic scalings of the double-layer potential, as a function of an anomalous transport coefficient alpha and of the perpendicular length scale l(a) of the arc. The arc potential phi(DL) scales approximately linearly with alpha, and for alpha fixed phi (DL) about l(a) to the z power. Using parameters appropriate to the auroral zone acceleration region, potentials of phi (DPL) 10 kV scale to projected ionospheric dimensions of about 1 km, with power flows of the order of magnitude of substorm dissipation rates.

Smith, R. A.↗

NASA NTRS1989

Gravitational instability in a primordial collapsing gas cloud

This paper presents an analysis of the linear evolution of short-wavelength perturbations in a background fluid flow which is undergoing gravitational collapse on large scales. Local evolution equations for perturbations to an arbitrary flow are derived in the linear regime and the short-wavelength limit. Local perturbation behavior in an inhomogeneous flow is found to be the same as that in a homogeneous anisotropic flow having the same local velocity field. Background flows in which the scale factors vary as power laws in time are considered to illustrate the relative effects of self-gravity, pressure and kinematics of the background flow on the density perturbation evolution. Perturbation analyses are then presented for more realistic background flows arising from the evolution into the nonlinear regime of initially small density perturbations in an isotropically expanding cosmological model. For low-pressure, inhomogeneous collapses, kinematic effects tend to dominate over self-gravity in driving perturbation growth as the collapse proceeds.

Lacey, Cedric G.↗

NASA NTRS1995

Nonlinear Waves in Magnetized Accretion Disks

Time-dependent accretion for a magnetized disk can exhibit short timescale outbursts of high-power jets associated with bursts of disk radiation. The burst of energy in jets can produce outward propagating disturbances in preexisting (+/- z) jet flows. the disturbances are strong and can be expected to steepen and form strong shock waves. The strong linear polarization (up to approximately 30%) and large polarization position angle changes (90 deg and more) seen in the optical outbursts of some quasars clearly indicate synchrotron radiation, and this component of the radiation is probably associated with the burst in jet energy in the present model.

Lovelace, R. V. E.↗

NASA NTRS2000

Novel Integrated Radial and Axial Magnetic Bearing

Typically, fully active magnetically suspended systems require one axial and two radial magnetic bearings. Combining radial and axial functions into a single device allows for more compact and elegant packaging. Furthermore, in the case of high-speed devices such as energy storage flywheels, it is beneficial to minimize shaft length to keep rotor mode frequencies as high as possible. Attempts have been made to combine radial and axial functionality, but with certain drawbacks. One approach requires magnetic control flux to flow through a bias magnet reducing control effectiveness, thus resulting in increased resistive losses. This approach also requires axial force producing magnetic flux to flow in a direction into the rotor laminate that is undesirable for minimizing eddy-current losses resulting in rotational losses. Another approach applies a conical rotor shape to what otherwise would be a radial heteropolar magnetic bearing configuration. However, positional non-linear effects are introduced with this scheme and the same windings are used for bias, radial, and axial control adding complexity to the controller and electronics. For this approach, the amount of axial capability must be limited. It would be desirable for an integrated radial and axial magnetic bearing to have the following characteristics, separate inputs for radial and axial control for electronics and control simplicity, all magnetic control fluxes should only flow through their respective air gaps and should not flow through any bias magnets for minimal resistive losses, be of a homopolar design to minimize rotational losses, position related non-linear effects should be minimized, and dependent upon the design parameters, be able to achieve any radial/axial force or power ratio as desired. The integrated radial and axial magnetic bearing described in this paper exhibits all these characteristics. Magnetic circuit design, design equations, and analysis results will be presented.

Blumenstock, Kenneth A.↗

NASA NTRS2000

Novel Integration Radial and Axial Magnetic Bearing

Typically, fully active magnetically suspended systems require one axial and two radial magnetic bearings. Combining radial and axial functions into a single device allows for more compact and elegant packaging. Furthermore, in the case of high-speed devices such as energy storage flywheels, it is beneficial to minimize shaft length to keep rotor mode frequencies as high as possible. Attempts have been made to combine radial and axial functionality, but with certain drawbacks. One approach requires magnetic control flux to flow through a bias magnet reducing control effectiveness, thus resulting in increased resistive losses. This approach also requires axial force producing magnetic flux to flow in a direction into the rotor laminate that is undesirable for minimizing eddy-current losses resulting in rotational losses. Another approach applies a conical rotor shape to what otherwise would be a radial heteropolar magnetic bearing configuration. However, positional non-linear effects are introduced with this scheme and the same windings are used for bias, radial, and axial control adding complexity to the controller and electronics. For this approach, the amount of axial capability must be limited. It would be desirable for an integrated radial and axial magnetic bearing to have the following characteristics; separate inputs for radial and axial control for electronics and control simplicity, all magnetic control fluxes should only flow through their respective air gaps and should not flow through any bias magnets for minimal resistive losses, be of a homopolar design to minimize rotational losses, position related non-linear effects should be minimized, and dependent upon the design parameters, be able to achieve any radial/axial force or power ratio as desired. The integrated radial and axial magnetic bearing described in this paper exhibits all these characteristics. Magnetic circuit design, design equations, and magnetic field modeling results will be presented.

Blumenstock, Kenneth↗

NASA NTRS2015

Comparison of Computational and Experimental Results for a Transonic Variable-Speed Power-Turbine Blade Operating with Low Inlet Turbulence Levels

A computational assessment of the aerodynamic performance of the midspan section of a variable-speed power-turbine blade is described. The computation comprises a periodic single blade that represents the 2-D Midspan section VSPT blade that was tested in the NASA Glenn Research Center Transonic Turbine Blade Cascade Facility. A commercial, off-the-shelf (COTS) software package, Pointwise and CFD++, was used for the grid generation and RANS and URANS computations. The CFD code, which offers flexibility in terms of turbulence and transition modeling options, was assessed in terms of blade loading, loss, and turning against test data from the transonic tunnel. Simulations were assessed at positive and negative incidence angles that represent the turbine cruise and take-off design conditions. The results indicate that the secondary flow induced at the positive incidence cruise condition results in a highly loaded case and transitional flow on the blade is observed. The negative incidence take-off condition is unloaded and the flow is very two-dimensional. The computational results demonstrate the predictive capability of the gridding technique and COTS software for a linear transonic turbine blade cascade with large incidence angle variation.

turbomachinery↗

DOE OSTI2021

Adiabatic behavior of an elliptical vortex in a time-dependent external strain flow

The adiabatic behavior of two-dimensional (2D) fluid vortices subject to slowly varying, time-dependent external strain flows is studied theoretically, and experimentally using magnetized non-neutral electron plasmas. Here the E × B drift dynamics of the electrons perpendicular to the magnetic field are analogous to the motion of fluid vorticity under the 2D Euler equations describing ideal fluids. A low-dimensional elliptical vortex patch model is used along with a WKB approximation to derive a formula for the breaking of an adiabatic invariant due to the changing external flow. The invariant is interpreted as the amplitude of a perturbative oscillation about a stable fixed point corresponding to a steady elliptical vortex. Smooth, hyperbolic tangent and piecewise linear ramp functions are considered for the external strain time dependence. Standard exponential breaking is observed in the former case, whereas the latter exhibits a power-law breaking curve with periodic modulation. It is found that a driving term in the equations of motion contributes the majority of the breaking whereas the frequency variation plays a weaker, but significant role. The experimental data agree closely with the theoretical model. The most significant deviation is due to inviscid damping behavior associated with the smooth edges of the experimental vortices, which tends to reduce the amplitude of the oscillation. Finally, the results are compared and contrasted with other related experimental, numerical, and theoretical work.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

High Fidelity Computational Model for Fluidized Bed Experiments (Final Report)

MFiX was integrated with preconditioners and linear solver packages in Trilinos via MFIX, Fortran, C, and C++ wrappers. The MFIX wrapper interpreted the structure of the matrix and vector from MFiX while the Fortran wrapper transfers this information to a low-level language, C. C-wrapper transforms the memory semantic between Fortran and C++ language. C++ wrapper passes the matrix and vector to a Trilinos package and gets the solution. This solution was transferred to MFiX via C++, C, Fortran, MFIX wrapper. The framework is used to integrate first, second and third generation linear solvers in Trilinos with MFiX.

20 FOSSIL-FUELED POWER PLANTS↗

NASA NTRS2015

Comparison of Computational and Experimental Results for a Transonic Variable-speed Power-Turbine Blade Operating with Low Inlet Turbulence Levels

rotary wing↗

DOE OSTI2025

Pump with Broadband Probe Experiments for Single-Shot Measurements of Plasma Conditions and Crossed-Beam Energy Transfer

Here, a novel technique for measuring plasma conditions using monochromatic pump-broadband-probe laser interactions has been experimentally demonstrated. Originally proposed in Ludwig et al. [Phys. Plasmas 26, 113108 (2019)], this method utilizes crossed-beam energy transfer between the broadband probe and the pump, mediated by plasma ion acoustic waves. The complete energy transfer spectrum can be captured in a single shot, enabling the inference of plasma parameters such as density, electron and ion temperatures, and flow velocity. Compared to Thomson scattering, this technique offers signal enhancements typically larger than 9 orders of magnitude, significantly reducing the required probe laser intensity and facilitating interactions that are linear and measurements that are nonperturbative of the plasma. Furthermore, it provides a powerful tool for advancing studies of crossed-beam energy transfer under conditions relevant to inertial confinement fusion experiments.

Physics - Plasma physics↗

NASA NTRS1990

The Mach number of the cosmic flow - A critical test for current theories

A new cosmological, self-contained test using the ratio of mean velocity and the velocity dispersion in the mean flow frame of a group of test objects is presented. To allow comparison with linear theory, the velocity field must first be smoothed on a suitable scale. In the context of linear perturbation theory, the Mach number M(R) which measures the ratio of power on scales larger than to scales smaller than the patch size R, is independent of the perturbation amplitude and also of bias. An apparent inconsistency is found for standard values of power-law index n = 1 and cosmological density parameter Omega = 1, when comparing values of M(R) predicted by popular models with tentative available observations. Nonstandard models based on adiabatic perturbations with either negative n or small Omega value also fail, due to creation of unacceptably large microwave background fluctuations.

Ostriker, Jeremiah P.↗

NASA NTRS1952

Air forces and moments on triangular and related wings with subsonic leading edges oscillating in supersonic potential flow

This analysis treats the air forces and moments in supersonic potential flow on oscillating triangular wings and a series of sweptback and arrow wings with subsonic leading edges and supersonic trailing edges. For the wings undergoing sinusoidal torsional oscillations simultaneously with vertical translations, the linearized velocity potential is derived in the form of a power series in terms of a frequency parameter. This method can be useful for treatment of similar problems for other plan forms and for wings undergoing other sinusoidal motions. For triangular wings, as many terms of such a series expansion as may be derived can be determined; however, the terms after the first few become very cumbersome. Closed expressions that include the reduced frequency to the fifth power, an order which is sufficient for a large class of practical application, are given for the velocity potential and for the components of chordwise section force and moment coefficients. These wings are found to exhibit the possibility of undamped torsional oscillations for certain ranges of Mach number and locations of the axis of rotation. The ranges of these parameters are delineated for triangular wings.

Watkins, Charles E↗

NASA NTRS2012

Mars Science Laboratory Drill

This drill (see Figure 1) is the primary sample acquisition element of the Mars Science Laboratory (MSL) that collects powdered samples from various types of rock (from clays to massive basalts) at depths up to 50 mm below the surface. A rotary-percussive sample acquisition device was developed with an emphasis on toughness and robustness to handle the harsh environment on Mars. It is the first rover-based sample acquisition device to be flight-qualified (see Figure 2). This drill features an autonomous tool change-out on a mobile robot, and novel voice-coil-based percussion. The drill comprises seven subelements. Starting at the end of the drill, there is a bit assembly that cuts the rock and collects the sample. Supporting the bit is a subassembly comprising a chuck mechanism to engage and release the new and worn bits, respectively, and a spindle mechanism to rotate the bit. Just aft of that is a percussion mechanism, which generates hammer blows to break the rock and create the dynamic environment used to flow the powdered sample. These components are mounted to a translation mechanism, which provides linear motion and senses weight-on-bit with a force sensor. There is a passive-contact sensor/stabilizer mechanism that secures the drill fs position on the rock surface, and flex harness management hardware to provide the power and signals to the translating components. The drill housing serves as the primary structure of the turret, to which the additional tools and instruments are attached. The drill bit assembly (DBA) is a passive device that is rotated and hammered in order to cut rock (i.e. science targets) and collect the cuttings (powder) in a sample chamber until ready for transfer to the CHIMRA (Collection and Handling for Interior Martian Rock Analysis). The DBA consists of a 5/8-in. (.1.6- cm) commercial hammer drill bit whose shank has been turned down and machined with deep flutes designed for aggressive cutting removal. Surrounding the shank of the bit is a thick-walled maraging steel collection tube allowing the powdered sample to be augured up the hole into the sample chamber. For robustness, the wall thickness of the DBA was maximized while still ensuring effective sample collection. There are four recesses in the bit tube that are used to retain the fresh bits in their bit box. The rotating bit is supported by a back-to-back duplex bearing pair within a housing that is connected to the outer DBA housing by two titanium diaphragms. The only bearings on the drill in the sample flow are protected by a spring-energized seal, and an integrated shield that diverts the ingested powdered sample from the moving interface. The DBA diaphragms provide radial constraint of the rotating bit and form the sample chambers. Between the diaphragms there is a sample exit tube from which the sample is transferred to the CHIMRA. To ensure that the entire collected sample is retained, no matter the orientation of the drill with respect to gravity during sampling, the pass-through from the forward to the aft chamber resides opposite to the exit tube.

Okon, Avi B.↗