Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “interfacial degradation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

The mechanism of hydroxyapatite coatings degradation at high substrate temperatures

Physical vapor deposition methods used for hydroxyapatite (HA) coatings typically require elevated substrate temperatures and post-deposition annealing to induce crystallization. However, such thermal treatments can degrade both the mechanical integrity and bioactivity of the coating, particularly when substrate temperatures exceed 500 °C. The mechanisms underlying these phenomena remain insufficiently understood. In this study, HA thin films were deposited on silicon and Ti6Al4V substrates using pulsed laser deposition and were systematically characterized to elucidate these mechanisms. XPS and SIMS analyses revealed a temperature-dependent loss of OH − and PO 4 3− groups, an increased Ca/P ratio, and the formation of interfacial oxides, all of which contribute to weakened adhesion. To clarify the temperature-dependent decline in bioactivity, protein adsorption behavior was analyzed using a Kramers-type kinetic framework; the fitted desorption kinetics indicate that coatings deposited near ∼500 °C provide the most stable protein attachment, whereas higher temperatures accelerate desorption due to dehydroxylation and carbonate substitution. Together, these findings provide mechanistic insight into the thermal degradation of HA coatings and offer a framework for optimizing deposition parameters to preserve stoichiometry, adhesion, and bioactivity for long-term biomedical applications.

Kylychbekov, Salizhan [Univ. of Oxford (United Kin↗
DOE OSTI2021

Prospects for the expansion of standing wave ambient pressure photoemission spectroscopy to reactions at elevated temperatures

Standing wave ambient pressure photoemission spectroscopy (SWAPPS) is a promising method to investigate chemical and potential gradients across solid-vapor and solid-liquid interfaces under close-to-realistic environmental conditions, far away from high vacuum. Until now, these investigations have been performed only near room temperature, but for a wide range of interfacial processes, chief among them being heterogeneous catalysis, measurements at elevated temperatures are required. One concern in these investigations is the temperature stability of the multilayer mirrors, which generate the standing wave field. At elevated temperatures, degradation of the multilayer mirror due to, for example, interdiffusion between the adjacent layers, decreases the modulation of the standing wave field, thus rendering SWAPPS experiments much harder to perform. Here, we show that multilayer mirrors consisting of alternate B4C and W layers are stable at temperatures exceeding 600 °C and are, thus, promising candidates for future studies of surface and subsurface species in heterogeneous catalytic reactions using SWAPPS.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Irradiation-induced amorphization of UO 2 films prepared by spraying-assisted combustion synthesis

Spraying-assisted combustion synthesis with uranyl nitrate – acetylacetone – 2-methoxyethanol solutions was used to prepare UO 2 films on an aluminum alloy substrate. The tuning of the spraying parameters and annealing temperatures allowed the preparation of UO 2 films with thicknesses varying from 10–300 nm and 5–10 nm UO 2 grain size. High-resolution electron microscopy and X-ray photoelectron spectroscopy showed that increasing the annealing temperature promotes Mg diffusion from the substrate into the films. The incorporation of Mg reduced the overall crystallinity of the films. The irradiation with Ar 2+ ions (1.7 MeV energy and a fluence of 2 × 10 16 ions/cm 2 ) did not degrade the quality of the films. However, the Mg content significantly influenced the irradiation-induced restructuring of the UO 2 films. Irradiated films with low or no Mg content exhibit high crystallinity, and the UO 2 /Al interfacial layer becomes highly porous. Films with higher Mg content are mostly amorphized after irradiation. The origin of irradiation-induced amorphization was related to the formation of Mg y U 1-y O 2±x solid solutions. Chemically complex, pore-free, and amorphous Mg-Al-O film/substrate interfacial layers enable continuous Mg diffusion during irradiation. As a result, the gradual increase in Mg amounts triggers irradiation-induced precipitation of a crystalline MgO-rich phase within the amorphous films.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
NASA NTRS1990

Thermo-oxidative stability studies of PMR-15 polymer matrix composites reinforced with various continuous fibers

An experimental study was conducted to measure the thermooxidative stability of PMR-15 composites reinforced with various fibers and to observe differences in the way they degrade in air. The fibers studied include graphite and the thermally stable Nicalon and Nextel ceramic fibers. Weight-loss rates for the different composites were assessed as a function of mechanical properties, specimen geometry, fiber sizing, and interfacial bond strength. Differences were observed in rates of weight loss, matrix cracking, geometry dependency, and fiber sizing effects. It was shown that Celion 6000 fiber-reinforced composites do not exhibit a straight-line Arrhenius relationship at temperatures above 316 C.

Bowles, Kenneth J.↗
NASA NTRS1995

Fatigue Crack Growth and Crack Bridging in SCS-6/Ti-24-11

Interfacial damage induced by relative fiber/matrix sliding was found to occur in the bridged zone of unidirectional SCS-6/Ti-24Al-11Nb intermetallic matrix composite specimens subjected to fatigue crack growth conditions. The degree of interfacial damage was not uniform along the bridged crack wake. Higher damage zones were observed near the machined notch in comparison to the crack tip. The interfacial friction shear strength tau(sub f) measured in the crack wake using pushout testing revealed lower values than the as-received interface. Interfacial wear also reduced the strength of the bridging fibers. The reduction in fiber strength is thought to be a function of the magnitude of relative fiber/matrix displacements ind the degree of interfacial damage. Furthermore, two different fiber bridging models were used to predict the influence of bridging on the fatigue crack driving force. The shear lag model required a variable tau(sub f) in the crack wake (reflecting the degradation of the interface) before its predictions agreed with trends exhibited by the experimental data. The fiber pressure model did an excellent job in predicting both the FCG data and the DeltaCOD in the bridged zone even though it does not require a knowledge of tau(sub f).

Ghosn, Louis J.↗
DOE OSTI2021

Balancing Interfacial Reactions to Achieve Long Cycle Life in High Energy Lithium Metal Batteries

Rechargeable lithium (Li) metal batteries have attracted wide attentions as the next generation energy storage technologies. However, simultaneously achieving high cell-level energy density and long cycle life in realistic batteries is still a great challenge. Here we investigate the cell degradation mechanisms of Li||LiNi0.6Mn0.2Co0.2O2 pouch cells using different, but representative cell configurations to understand the fundamental linkage among Li thickness, electrolyte depletion and the structure evolution of solid electrolyte interphase (SEI) layers. Different cell failure modes were discovered when tuning the anode to cathode capacity (N/P) ratio in compatible electrolyte. With a thick-Li anode (N/P ratio = 2.5), initial stable cycling is obtained because of the abundant Li supply from the anode together with an artificially inflated high Coulombic Efficiency, followed by a premature sudden cell death appears due to the enrichment of “ineffective SEI” which does not participate in the electrochemical reactions but keep increasing cell impedance. The anode-free cell (N/P 0:1) displays a steady capacity decay because cathode Li loss dominates from the beginning to the end of cell cycle life. An optimized thin-Li (N/P 1:1) well balances the Li consumption rate with the impedance buildup by minimizing the growth of ineffective SEI layer, thus decelerates cell polarization increasing and extends cycling. Contrary to conventional wisdoms, long cycle life is observed by using ultra thin-Li (20 µm) in balanced cells. A prototype 350 Wh kg-1 pouch cell (2.0 Ah) achieves over 600 long stable cycles with 76% capacity retention without sudden cell death.

Niu, Chaojiang↗
NASA NTRSDate not supplied

Bio Inspired Surface Structures to Mitigate Interfacial Particle Adhesion: A Review

Nature has perfected surface chemical and topographical engineering to enable survival in extreme environments. Biomimetics is a rapidly expanding field where biologically inspired design facilitates elegant, yet practical, solutions across many applications. NASA’s ARTEMIS program focused on lunar missions will require unique ways to solve the challenge of highly abrasive, chemically reactive and electrostatically charged lunar dust that adheres strongly to all exposed surfaces and degrades functionality. While seeking solutions to find a surface for mitigating lunar dust adhesion, we looked at natural terrestrial surfaces that successfully minimize dust adhesion and wear for inspiration. Lunar dust is comprised of highly abrasive particles, more than 90% of which are composed of silicate materials. Adapting to somewhat similar particulates in hot and arid deserts of the world, the sandfish lizard has a skin structure that allows it to swim in the sand with minimum friction and adhesion. Special surface adaptations of the tamarisk plant help protect it from severe sandstorms. The desert scorpion has grooves and bumps on its carapace that have been shown to minimize erosion in the sand. Beyond these examples, there are numerous other natural surfaces that have evolved to mitigate particle adhesion and wear. Several efforts have been made by different researchers to replicate these natural surfaces using methods such as laser patterning, 3D printing, chemical vapor deposition and other physical and chemical processes. The resulting bio-inspired patterned surfaces have shown reduction in interfacial particle adhesion, friction, and wear, among other properties. This paper aims to review published research on the subject that might help develop lunar dust adhesion and wear mitigating material surfaces for future lunar applications.

Lunar dust, Lunar surface, Adhesion mitigation, Bi↗
NASA NTRS1990

Thermo-oxidative stability studies of PMR-15 polymer matrix composites reinforced with various fibers

An experimental study was conducted to measure the thermo-oxidative stability of PMR-15 polymer matrix composites reinforced with various fibers and to observe differences in the way they degrade in air. The fibers that were studied included graphite and the thermally stable Nicalon and Nextel ceramic fibers. Weight loss rates for the different composites were assessed as a function of mechanical properties, specimen geometry, fiber sizing, and interfacial bond strength. Differences were observed in rates of weight loss, matrix cracking, geometry dependency, and fiber-sizing effects. It was shown that Celion 6000 fiber-reinforced composites do not exhibit a straight-line Arrhenius relationship at temperatures above 316 C.

Bowles, Kenneth J.↗
DOE OSTI2026

Biocatalyst discovery and design for plastics deconstruction: A multi‐scale perspective

Plastic waste accumulation poses significant environmental challenges due to a lack of economical solutions for the molecular deconstruction of diverse synthetic polymers. Biological‐based degradation offers promise but is hindered by the crystallinity, hydrophobicity, and additive complexity of plastics, which restrict biocatalyst access and activity. To address these problems, we propose a multi‐scale framework that combines detailed materials characterization, optimization of plastic‐biomolecular interfacial interactions, and enhancement of biocatalytic kinetics to develop effective plastic‐deconstructing enzymes. This approach leverages principles from reaction kinetics, transport and interfacial phenomena, and enzyme engineering to systematically address barriers across diverse plastic types. Our framework aims to accelerate the discovery and optimization of biocatalysts capable of scalable, selective, and efficient deconstruction of plastic waste. These advances hold potential to enable sustainable biological recycling and upcycling pathways, contributing to global efforts in mitigating plastic pollution and promoting circular material economies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Electro-Chemo-Mechanical Evolution at the Garnet Solid Electrolyte–Cathode Interface

Solid-state batteries promise higher energy density and improved safety compared with lithium-ion batteries. However, electro-chemomechanical instabilities at the solid electrolyte interface with the cathode and the anode hinder their large scale implementation. Here, in this study, we focus on resolving electro-chemo-mechanical instability mechanisms and their onset conditions between a state-of-the-art cathode, LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622), and the garnet Li 7 La 3 Zr 2 O 12 (LLZO) solid electrolyte. We used thin-film NMC622 on LLZO pellets to place the interfacial region within the detection depth of the X-ray characterization techniques. The experimental probes of the near-interface region included in operando X-ray absorption spectroscopy and ex situ focused ion beam scanning electron microscopy. Electrochemical degradation was not observable during cycling at room temperature with 4.3 V versus Li/Li + charge voltage cutoff, or with stepwise potentiostatic hold up to 4.1 V versus Li/Li + . In contrast, secondary phases including reduced transition metal species (Ni 2+ , Co 2+ ) were found after cycling up to 4.3 V versus Li/Li + at 80 °C and during potentiostatic hold at 4.3 V versus Li/Li + (Ni 2+ ). Intergranular cracks between NMC622 grains and delamination at the NMC622|LLZO interface occurred readily after the first charge. These interface reaction products and mechanical failure lowered the capacity and cell efficiency due to partial loss of the NMC622 phase, partial loss of contact at the interface, and a higher polarization resistance. Electrochemical instability between delithiated NMC622 and LLZO could be mitigated by using a low charge voltage cutoff or cycling at lower temperature. Ways to engineer the mechanical properties to avoid crack deflection and delamination at the interface are also discussed for enhancing mechanical stability.

36 MATERIALS SCIENCE↗
NASA NTRS1989

The application of electrochemical impedance spectroscopy for characterizing the degradation of Ni(OH)2/NiOOH electrodes

Electrochemical impedance spectra of rolled and bonded and sintered porous nickel battery electrodes were recorded periodically during charge/discharge cycling in concentrated KOH solution at various temperatures. A transmission line model (TLM) was adopted to represent the impedance of the porous electrodes, and various model parameters were adjusted in a curve fitting routine to reproduce the experimental impedances. Degradation processes for rolled and bonded electrodes were deduced from changes in model parameters with electrode cycling time. In developing the TLM, impedance spectra of planar (non-porous) electrodes were used to represent the pore wall and backing plate interfacial impedances. These data were measured over a range of potentials and temperatures, and an equivalent circuit model was adopted to represent the planar electrode data. Cyclic voltammetry was used to study the characteristics of the oxygen evolution reaction on planar nickel electrodes during charging, since oxygen evolution can affect battery electrode charging efficiency and ultimately electrode cycle life if the overpotential for oxygen evolution is sufficiently low. Transmission line modeling results suggest that porous rolled and bonded nickel electrodes undergo restructuring during charge/discharge cycling prior to failure.

Macdonald, D. D.↗
NASA NTRS1987

Temperature-dependent tensile and shear response of graphite/aluminum

The thermo-mechanical response of unidirectional P100 graphite fiber/6061 aluminum matrix composites was investigated at four temperatures:-150, +75, +250, and +500 F. Two types of tests, off-axis tension and losipescu shear, were used to obtain the desired properties. Good experimental-theoretical correlation was obtained for Exx, vxy, and G12. It is shown that E11 is temperature independent, but E22, v12, and G12 generally decrease with increasing temperature. Compared with rather high longitudinal strength, very low transverse strength was obtained for the graphite/aluminum. The poor transverse strength is believed to be due to the low interfacial bond strength in this material. The strength decrease significantly with increasing temperature. The tensile response at various temperatures is greatly affected by the residual stresses caused by the mismatch in the coefficients of thermal expansion of fibers and matrix. The degradation of the aluminum matrix properties at higher temperatures has a deleterious effect on composite properties. The composite has a very low coefficient of thermal expansion in the fiber direction.

Fujita, T.↗
NASA NTRS1992

Design for progressive fracture in composite shell structures

The load carrying capability and structural behavior of composite shell structures and stiffened curved panels are investigated to provide accurate early design loads. An integrated computer code is utilized for the computational simulation of composite structural degradation under practical loading for realistic design. Damage initiation, growth, accumulation, and propagation to structural fracture are included in the simulation. Progressive fracture investigations providing design insight for several classes of composite shells are presented. Results demonstrate the significance of local defects, interfacial regions, and stress concentrations on the structural durability of composite shells.

Minnetyan, Levon↗
NASA NTRS1982

SiC or B4C-B/low strategic element content composite

Advancements in materials technologies are needed to provide the aerospace industry with alternate material options in the event of future strategic metal shortages and to optimize performance of engines. Composite materials are promising candidates for such an application. The potential of SiC and B4C-B filament reinforced low strategic element iron-base alloy content composites or use at 760 to 870 C is considered. A limiting factor towards developing this material for high temperature use has been the reaction between the filament and matrix material during fabrication and service which degrades filament strength. A low temperature fabrication process to limit filament/matrix reaction is being developed which involves the use of hollow cathode sputtering to coat the filaments with iron-base alloys of various compositions. An investigation is being conducted to determine the interfacial reaction effects of SiC and B4C-B filaments with iron-base alloys to develop an understanding of filament/matrix alloy compatibility for 760 to 870 C service.

Petrasek, D. W.↗
DOE OSTI2023

Consequences of utilizing a redox-active polymeric binder in Li-ion batteries

Development of new polymeric binders can help enable the use of silicon-rich anodes in Li-ion batteries, by providing stronger adhesion to the active material particles. The compositional features that improve interfacial interactions and mechanical properties can often impart electronic conductivity and redox activity to these polymers, which are generally seen as beneficial to cell performance. Alternatively, it is also possible that the addition of charge-transferring centers to the electrode can accelerate cell degradation. Here, we use an aromatic polyimide (∼320 mA h/g of reversible capacity) to explore how a redox-active conductive polymer can affect cell performance. We demonstrate that the lithiated polymer is less stable than the traditional binders upon storage, leading to increased rates of calendar aging. Furthermore, we determine that the adhesion properties of the polymer deteriorate upon repeated cycling, to an extent that is proportional to the degree of delithiation of the binder. More critically, we establish that progressive degradation of the redox behavior of the polymer leads to the release of “extra” Li + into the cell, which can give the false perception of good performance even under conditions of poor stability. In conclusion, our work suggests that redox-active conductive binders can sometimes be detrimental to cell performance, and that works evaluating new polymers must include careful experimental validation under realistic conditions.

25 ENERGY STORAGE↗
DOE OSTI2022

Transmission Electron Microscopy Study on the Effect of Thermal and Electrical Stimuli on Ge2Te3 Based Memristor Devices

Memristor devices fabricated using the chalcogenide Ge 2 Te 3 phase change thin films in a metal-insulator-metal structure are characterized using thermal and electrical stimuli in this study. Once the thermal and electrical stimuli are applied, cross-sectional transmission electron microscopy (TEM) and X-ray energy-dispersive spectroscopy (XEDS) analyses are performed to determine structural and compositional changes in the devices. Electrical measurements on these devices showed a need for increasing compliance current between cycles to initiate switching from low resistance state (LRS) to high resistance state (HRS). The measured resistance in HRS also exhibited a steady decrease with increase in the compliance current. High resolution TEM studies on devices in HRS showed the presence of residual crystalline phase at the top-electrode/dielectric interface, which may explain the observed dependence on compliance current. XEDS study revealed diffusion related processes at dielectric-electrode interface characterized, by the separation of Ge 2 Te 3 into Ge- and Te- enriched interfacial layers. This was also accompanied by spikes in O level at these regions. Furthermore, in-situ heating experiments on as-grown thin films revealed a deleterious effect of Ti adhesive layer, wherein the in-diffusion of Ti leads to further degradation of the dielectric layer. This experimental physics-based study shows that the large HRS/LRS ratio below the current compliance limit of 1 mA and the ability to control the HRS and LRS by varying the compliance current are attractive for memristor and neuromorphic computing applications.

Shallcross, Austin↗
DOE OSTI2022

Thermally Insulating, Thermal Shock Resistant Calcium Aluminate Phosphate Cement Composites for Reservoir Thermal Energy Storage

This paper presents the use of hydrophobic silica aerogel (HSA) and hydrophilic fly ash cenosphere (FCS) aggregates for improvements in the thermal insulating and mechanical properties of 100- and 250 °C-autoclaved calcium aluminate phosphate (CaP) cement composites reinforced with micro-glass (MGF) and micro-carbon (MCF) fibers for deployment in medium- (100 °C) and high-temperature (250 °C) reservoir thermal energy storage systems. The following six factors were assessed: (1) Hydrothermal stability of HSA; (2) Pozzolanic activity of the two aggregates and MGF in an alkali cement environment; (3) CaP cement slurry heat release during hydration and chemical reactions; (4) Composite phase compositions and phase transitions; (5) Mechanical behavior; (6) Thermal shock (TS) resistance at temperature gradients of 150 and 225 °C. The results showed that hydrophobic trimethylsilyl groups in trimethylsiloxy-linked silica aerogel structure were susceptible to hydrothermal degradation at 250 °C. This degradation was followed by pozzolanic reactions (PR) of HSA, its dissolution, and the formation of a porous microstructure that caused a major loss in the compressive strength of the composites at 250 °C. The pozzolanic activities of FCS and MGF were moderate, and they offered improved interfacial bonding at cement-FCS and cement-MGF joints through a bridging effect by PR products. Despite the PR of MGF, both MGF and MCF played an essential role in minimizing the considerable losses in compressive strength, particularly in toughness, engendered by incorporating weak HSA. As a result, a FCS/HSA ratio of 90/10 in the CaP composite system was identified as the most effective hybrid insulating aggregate composition, with a persistent compressive strength of more than 7 MPa after three TS tests at a 150 °C temperature gradient. This composite displayed thermal conductivity of 0.28 and 0.35 W/mK after TS with 225 and 150 °C thermal gradients, respectively. These values, below the TC of water (TC water = 0.6 W/mK), were measured under water-saturated conditions for applications in underground reservoirs. However, considering the hydrothermal disintegration of HSA at 250 °C, these CaP composites have potential applications for use in thermally insulating, thermal shock-resistant well cement in a mid-temperature range (100 to 175 °C) reservoir thermal energy storage system.

58 GEOSCIENCES↗
NASA NTRS2007

Growth and Characterization of 3C-SiC and 2H-AIN/GaN Films and Devices Produced on Step-Free 4H-SiC Mesa Substrates

While previously published experimental results have shown that the step-free (0 0 0 1) 4H-SiC mesa growth surface uniquely enables radical improvement of 3C-SiC and 2H-AlN/GaN heteroepitaxial film quality (greater than 100-fold reduction in extended defect densities), important aspects of the step-free mesa heterofilm growth processes and resulting electronic device benefits remain to be more fully elucidated. This paper reviews and updates recent ongoing studies of 3C-SiC and 2H-AlN/GaN heteroepilayers grown on top of 4H-SiC mesas. For both 3C-SiC and AlN/GaN films nucleated on 4H-SiC mesas rendered completely free of atomic-scale surface steps, TEM studies reveal that relaxation of heterofilm strain arising from in-plane film/substrate lattice constant mismatch occurs in a remarkably benign manner that avoids formation of threading dislocations in the heteroepilayer. In particular, relaxation appears to occur via nucleation and inward lateral glide of near-interfacial dislocation half-loops from the mesa sidewalls. Preliminary studies of homojunction diodes implemented in 3C-SiC and AlN/GaN heterolayers demonstrate improved electrical performance compared with much more defective heterofilms grown on neighbouring stepped 4H-SiC mesas. Recombination-enhanced dislocation motion known to degrade forward-biased 4H-SiC bipolar diodes has been completely absent from our initial studies of 3C-SiC diodes, including diodes implemented on defective 3C-SiC heterolayers grown on stepped 4H-SiC mesas.

Neudeck, P. G.↗