Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “hydrophilization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Cs retention and diffusion in C-S-H at different Ca/Si ratio

Cement and concrete are commonly used in the construction of repository sites for radioactive wastes. The correct isolation of those contaminants requires good adsorption and low diffusion rates. Both parameters are highly affected by many factors, such as pH, temperature or composition. The large variability of experimental conditions and formulations makes it extraordinarily difficult to tackle the influence of each of them independently in experimental samples. To this effect, molecular dynamics simulations have been employed in this study to investigate the role of the composition in the capacity to retain Cs and diffusivity of these ions in calcium silicate hydrate (C-S-H) gel pores. The results indicate that the adsorption of Cs ions is worsened at high Ca/Si ratios due to a lower interaction of the cations with the C-S-H surface, while hydrophilicity of the C-S-H nanopore rises, resulting in higher long-range ordering and lower diffusion coefficients of Cs ions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Impact of hydrophobic pendant phenyl groups on transport and co-transport of methanol and acetate in PEGDA-SPMAK cation exchange membranes

CO 2 reduction cells are innovative devices that reduce CO 2 into valuable chemicals (i.e. methanol (MeOH) and acetate (OAc – )) on the cathode. A major challenge with such devices is to develop ion exchange membranes that allow ion-selective transport (i.e., protons for cation exchange membranes, CEM) and suppress the crossover of CO 2 reduction products. To design such membranes, it is important to understand multi-solute transport behavior of these solutes. Previously, our group reported acetate diffusivities in co-transport with MeOH increase in sulfonated CEMs, where we speculated charge screening of the electrostatic interactions by co-diffusing MeOH has an impact. Here, crosslinked membranes fabricated by photopolymerization of poly(ethylene glycol) diacrylate (PEGDA), 3-sulfopropyl methacrylate potassium (SPMAK, SO 3 – -containing ionomer), and a phenyl-containing comonomer either phenoxyethyl acrylate (PEA) or poly(ethylene glycol) phenyl ether acrylate (PEGPEA)) are investigated. We observe OAc – diffusivities to both (1) PEGDA-SPMAK and (2) PEGDA-PEGPEA increase in co-diffusion with MeOH and those to (3) PEGDA-SPMAK/PEGPEA decrease. To rationalize this emergent co-transport behavior, we speculate (1) electrostatic interactions are interfered with by co-diffusing MeOH, (2) chain mobility (segmental dynamics) increases in the presence of MeOH and (3) for films with both hydrophobic (PEGPEA) and hydrophilic (SPMAK) comonomers chain mobility (segmental dynamics) decrease due to interactions between the comonomer sidechains depressing overall solute diffusivities. Finally, while further investigations are needed, this work contributes to improving our fundamental understanding of the relationships between polymer film chemistry, solute chemistry, and emergent cotransport behavior observed and described in this work (and others) towards enabling the design of improved membrane materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Rheological and microstructural characterization of aqueous suspensions of carbon black and reduced graphene oxide

Carbon black is often used as a conductivity enhancer in battery electrodes. Reduced graphene oxide is another conducting material, with a high aspect ratio sheet-like morphology, and offers the possibility of generating a conducting network at loadings that are small compared to carbon black. Suspensions of conducting carbon, active materials and binders are typically coated on current collectors during the formation of electrodes. The rheology of these suspensions is an important indicator of the connectivity of particles in the suspension and impacts the electrical conductivity as well as the thickness of the coated layer. In this work, the rheology and microstructures of aqueous suspensions of para-aminobenzoic acid terminated carbon black (CB) with and without reduced graphene oxide (RGO) were investigated. The CB loading varied between 0.05 wt.% -10 wt.%, while the samples containing RGO had an RGO loading of 0.05 wt.%. The pH of the suspension was varied from 7.5 to 3. The carboxyl groups on the CB surface are deprotonated at pH 7.5, making the particles hydrophilic. Protonation of the carboxylate groups at pH 3 makes the particles partially hydrophobic. Suspensions of CB showed Newtonian behavior at all loadings for pH 7.5, and at loadings below 1.5 wt.% for pH 3. They are shear thinning at loadings between 1.5–10 wt.%. Interestingly, the low shear viscosity is non-monotonic with CB loading, rising up to a CB loading of 7.5 wt.%, and then dropping at 10 wt.%. Cryogenic scanning electron microscopy (SEM) showed CB particles forming aggregates at pH 3 for CB loadings greater than 1.5 wt.%. At pH 3, addition of 0.05 wt.% RGO resulted in a viscosity increase for suspensions containing 0.5 wt.% CB, as the RGO formed connections with CB particles that enhanced network formation. Adding RGO had little effect on suspensions that had 1.5 wt.% CB. The combination of SEM imaging and suspension rheology provides insight into the particle connectivity for the carbon-based materials studied here. These insights will be useful in determining coating conditions for slurries used in rechargeable battery electrodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Simulation and analysis of slip flow of water at hydrophobic silica surfaces of nanometer slit pores

Water flow in nanopores is controlled fundamentally by pore wettability and interfacial water features. In the research herein reported, Molecular dynamics (MD) was used to simulate water flow in nanometer slit pores of silica surfaces with variable wetting characteristics. Compared to Couette flow, the simulated slit-pores of the talc (001) and octadecyltrichlorosilane (OTS) monolayer surfaces exhibited water flow enhancement and a positive slip length at the interface, whereas water flow velocity at the quartz (001) and amorphous silica surfaces was zero, adhering to the no slip condition. More intensive interactions between the interfacial water and hydrophilic silica surfaces were confirmed by MD simulation and sum-frequency vibrational spectroscopy (SFVS) results. A water exclusion zone of approximately 3 Å was found at the hydrophobic silica surfaces by quantitative MD interfacial water analysis and validated by SFVS. This exclusion zone dimension was similar in magnitude to the slip length (4–5 Å) as determined from simulated water flow in hydrophobic silica slit pores. The simulated slip lengths at the hydrophobic surfaces (0.2–1 nm) were significantly less than the experimental slip lengths (>40 nm) reported in the literature. In the case of the experimental results, this difference appears to be due to nanobubbles expected to be present at hydrophobic surfaces.

42 ENGINEERING↗
DOE OSTI2025

Sizing of discontinuous natural fibers: Effect of sizing approach and sizing concentration on composite properties

Natural fiber reinforced composites (NFRCs) are gaining attention in automotive applications as an alternative to glass fiber composites due to their lightweight and renewable sourcing. However, the inherent hydrophilicity of natural fibers leads to poor compatibility with hydrophobic polymers which adversely affects the mechanical properties of the composites and can limit their application to non-structural parts. Sizing is a common approach used for synthetic fibers to improve the interface between fiber and matrix. However, there is limited study on the sizing of natural fibers, and hence the focus of this work. Here, in this study, two different approaches to sizing discontinuous coir fibers were investigated, namely; (1) ex-situ sizing and (2) in-situ sizing. A commercial polypropylene (PP) based sizing agent was used and the effects of varying sizing solution concentrations (1.5, 2.5, and 3.5 wt%) on the properties of the composites was studied. Results showed that composites prepared via the in-situ sizing process had better fiber–matrix adhesion and improved tensile properties compared to ex-situ sized composites. On studying the effect of different sizing concentrations on composite properties, we found that the tensile strength of the composites increased (by ∼ 42 %) up to 2.5 wt% sizing concentration (in solution) and then decreased. However, the impact strength decreased significantly on increasing the sizing content beyond 1.5 wt% (by ∼ 40 %). Additionally, the study was further extended to investigate the effect of sizing on different NFRCs (coir, banana, and cottonized hemp fiber) where effectiveness of sizing was found to be influenced by the fiber surface morphology.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effects of graphene surface functionalities towards controlled reinforcement of a lignin based renewable thermoplastic rubber

In this report, we describe methods to enhance mechanical properties of a renewable thermoplastic rubber by incorporating functional graphene platelets into an equal-mass mixture of lignin, a feedstock from plant biomass, and a nitrile-butadiene rubber having 41 mol % acrylonitrile content (NBR41) that form a nanocomposite. Not all lignins yield mechanically strong material when they are combined with NBR41, and thus, limit its use for such rubbery products. Here, we evaluate different graphene oxides (GO) and reduced graphene oxides (rGO) dry-powders with different surface areas, functionality, and wettability in the synthesis of performance-enhanced nanocomposites of soft lignin/NBR41 matrix via a solvent-free, high shear reactive process. High surface area GO (HSGO) platelets with strong hydrophilicity exhibit good dispersion in the multiphase lignin/NBR41 composites with lignin dispersion varying from 200 to 2000 nm, resulting in superior reinforcement over other graphene derivatives. The addition of 1–4 wt % HSGO increased the tensile stress of the lignin/NBR41 thermoplastic rubber matrix by 60–160% (15–24 MPa) and the modulus by 200–700% (60–140 MPa). Scanning electron microscopy and small angle X-ray scattering results show that the well-dispersed HSGO platelets effectively disrupt the lignin-rich aggregates in NBR41 matrix, resulting in both strength and stiffness enhancements in the formed nanocomposites. This report on performance enhancement of lignin-based renewable polymers via the production of nanocomposite would increase potential for ‘finding the value of lignin’—a grand challenge associated with modern biorefineries.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Fouling characterization and treatment of water reuse concentrate with membrane distillation: Do organics really matter

Membrane distillation (MD) for the treatment of concentrated brines has been limited in part by membrane fouling, resulting in subsequent flux decline and membrane wetting. This study provides new insight into the identification of fouling and scaling mechanisms and pretreatment strategies for mitigating flux decline with MD treatment of water reuse reverse osmosis concentrate (ROC). Bench-scale direct contact MD experiments were performed with untreated and pretreated ROC. Biological activated carbon (BAC), chemical water softening, or fluidized bed crystallization reactor coupled with ion exchange (FBCR-IX) were selected as pretreatment strategies to isolate the effects of organic fouling and calcium scaling. Organic and inorganic compounds were analyzed by high-performance liquid chromatography (HPLC) and inductively coupled plasma mass spectrometry (ICP-MS). Calcium ions were found to be the major contributor to flux decline despite the high organic content in the ROC. Minimal organic fouling is likely because the organic matter in the ROC is hydrophilic, limiting hydrophobic-hydrophobic interactions between the organics and the membrane. Furthermore, the water flux declined by 63 % after removing organic compounds by BAC pretreatment, with 60 % of the calcium mass precipitating from the solution. Whereas, the water flux remained constant after removing multivalent ions with fluidized bed crystallization. Cleaning the membrane by acid washing and temperature reversal recovered 73 % and 12 % of the water flux, respectively. The analyses outlined in this study can assist in selecting appropriate fouling and scaling mitigation strategies for water reuse ROC and a wide range of feed solutions used in MD applications.

42 ENGINEERING↗
DOE OSTI2026

Solar-powered self-descaling seesaw extractor for lithium production from seawater

The low Li + concentration and the abundance of competing ions limit the efficiency of lithium extraction from seawater. Here, in this work, we report a solar-powered seesaw extractor (SPSE) to boost Li + adsorption while minimizing scaling caused by competing ions during photothermal evaporation. The SPSE features a sandwich architecture, with a hydrophilic adsorbent layer placed between two hydrophobic photothermal layers. The seesaw configuration enables Li + to be elevated and concentrated through evaporation to overcome sluggish adsorption kinetics, while the associated salt scaling is removed by the seesawing motion. As a demonstration, we assembled 60 SPSEs into a 3 × 20 array that achieved a 15.5-fold increase in local Li + concentration and a 69.1% improvement in Li + uptake over 120 h, with a Li + /Na + separation factor exceeding 370,000.

localized enrichment↗
DOE OSTI2022

Electronic interactions and stability issues at the copper-graphene interface in air and in alkaline solution under electrochemical control

A micro-electrochemical cell is sealed with a polymer-free single-layer graphene (SLG) membrane to monitor the stability of Cu nanoparticles (NPs) attached to SLG, as well as the interfacial electronic interactions between Cu NPs and SLG both in air and in a mildly alkaline aqueous solution under electrochemical control. A combination of techniques, including in-situ Kelvin probe force microscopy (KPFM) and ex-situ electron microscopy, are applied. When Cu NPs are metallic at cathodic potentials, there is a relatively bias-independent offset in the SLG work function due to charge transfer at the Cu-SLG contact. When Cu NPs are oxidized at anodic potentials, on the other hand, the work function of SLG also depends on the applied bias in a quasi-linear fashion due to electrochemical gating, in addition to charge transfer at the CuOx-SLG contact. Furthermore, Cu NPs were found to oxidize and detach from SLG when kept under anodic potentials for a few hours, whereas they remain adhered to SLG at cathodic potentials. This is attributed to water intercalation at the CuO-SLG interface associated with the enhanced hydrophilicity of positively polarized graphene, as supported by the absence of Cu detachment following oxidation by galvanic corrosion in air.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

The energy saving potential of thermo-responsive desiccants for air dehumidification

The desiccant wheel is a promising technology for energy-efficient humidity control. However, its overall efficiency—hindered by the desiccant materials’ properties—remains low because traditional desiccants (e.g., silica gels) have a single isotherm regardless of their adsorption temperature. Thermo-responsive materials have been proposed to break this fixed affinity to water vapor, with drastically different adsorption isotherms depending on temperature. Its potential for improving dehumidification efficiency, however, has not been addressed. In this paper, we model the potential of a thermo-responsive interpenetrating polymer network (IPN) desiccant with temperature-dependent adsorption isotherms for energy-efficient dehumidification via a validated transient desiccant wheel model for humidity control of buildings. Thermo-responsive desiccants can improve the dehumidification performance due to their thermo-responsive switchable hydrophilicity below/above the lower critical solution temperature. Our analysis shows that thermo-responsive IPN desiccants can potentially reduce energy consumption by up to 30% compared to silica gels. Finally, the savings depend strongly on the critical temperature of the thermo-responsive desiccant and should be higher when the inlet temperatures are expected to be higher.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Superhydrophobic heat exchangers delay frost formation and enhance efficency of electric vehicle heat pumps

The number of electric vehicles has rapidly expanded as high-performance automotive lithium-ion batteries have become more affordable. However, the range of electric vehicles decreases in cold climates partly because of the additional thermal loads associated with cabin heating. One way to improve the efficiency of cabin heating is to replace resistive heating elements with an air-source heat pump system. However, to gain the full benefit of heat pumping, frost formation on the outdoor heat exchanger must be minimized. In this work, we modified the surface wettability of aluminum louvered-fin automotive heat pump evaporators and tested them under realistic operating conditions in a transcritical carbon dioxide (CO 2 ) heat pump. Each heat exchanger underwent several consecutive frosting and defrosting cycles to understand the cyclic performance of the system. The heat exchanger with a superhydrophobic outer surface was able to delay frost formation and maintain higher heat transfer rates when compared to heat exchangers with higher surface energies (hydrophilic). The delayed frost formation resulted in a system efficiency benefit in the first few frosting cycles but diminished in later cycles due to water retention and incomplete defrosting. However, for most automotive applications the superhydrophobic heat exchanger showed substantial benefits for normal driving trips. We report the scalable and optimized superhydrophobic heat exchangers developed here have the potential to increase the efficiency of automotive heat pumps and consequently increase the range and reduce energy consumption of electric vehicles.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2022

Coupled continuum and network model framework to study catalyst layers of polymer electrolyte fuel cells

The nanostructured thin film (NSTF) catalyst layers which have demonstrated high power densities, mass activities, and exceptional metal and support stability can have limited operational robustness due to their thin thickness and the hydrophilicity of the metal-coated nano whiskers. The dispersed nanostructured thin film (dNSTF) catalyst layers have been developed by dispersing the NSTF Pt whiskers with ionomer and carbon support to increase the thickness and hydrophobicity. Continuum and network models (NM) are coupled through boundary conditions to study the polymer electrolyte fuel cell with a dNSTF cathode catalyst layer. The coupled model combines the computational efficiency of the continuum model with the pore-scale information in the dNSTF cathode catalyst layer of the NM. It captures the special morphology of the partially ionomer/water covered cylindrical whiskers, as well as water percolation through the pore structures and their impact on the cell performance. Here we observe optimal ionomer coverage on whiskers to be 0.5, ionomer to carbon ratio to be 0.9 and higher whisker to carbon ratios to be desired.

08 HYDROGEN↗
DOE OSTI2025

Ectopic expression of pectate lyase PtxtPL1-27 in aspen affects leaf cuticle development

Cuticle - a hydrophobic barrier of cutin and waxes covering the outer cell wall surface of plants - enables survival in terrestrial habitats. However, it is not understood how the hydrophobic cuticle precursors travel through the homogalacturonan-rich hydrophilic cell wall. To elucidate the role of homogalacturonan in cuticle development, we disrupted its integrity by overexpressing a pectate lyase, PtxtPL1-27, in aspen. PtxtPL1-27 had pleiotropic effects on shoot development, including the reduction of cuticle thickness and changes in cutin and wax composition, but the expression of cutin biosynthetic genes was little affected. Despite a reduction in homogalacturonan content in the leaves, labeling with the homogalacturonan-specific antibody JIM5 in the outer epidermal cell wall layer increased and displayed an altered pattern. Moreover, the ultrastructure of cell walls was changed concomitant with lipid accumulation. We propose that the disruption of homogalacturonan integrity affected the cutinsome-dependent transport and polymerization of cutin monomers in the cell wall.

Plant Biology↗
DOE OSTI2021

Identification and quantification of distinct active sites in Hf-Beta zeolites for transfer hydrogenation catalysis

Despite the significant progress made in characterizing different framework heteroatom sites that exist in Lewis acidic zeolites with probe molecule adsorption and spectroscopy, methods to reliably quantify site counts remain indefinite and have been primarily limited to Sn and Ti Lewis acid sites. Here, methods to quantify framework Lewis acidic Hf 4+ sites in zeolite Beta (Hf-Beta) with two Lewis base titrants (pyridine, deuterated acetonitrile) were developed using infrared (IR) spectroscopy. Lewis acid site counts for Hf-Beta zeolites were validated by measuring integrated molar extinction coefficients (IMECs; ε, cm μmol –1 ) on Sn-Beta zeolites using identical Lewis base titrants to benchmark site counts with established literature procedures to quantify Lewis acid sites in Beta zeolites from IR spectra. Highlighting the importance of benchmarking active site counts against well-established experimental protocols, IMECs of CD 3 CN bound to open (ε(Sn; 2316 cm –1 ): 1.80 ± 0.25) and closed (ε(Sn; 2308 cm –1 ): 3.76 ± 0.33) Sn sites were ~1.8x larger than those previously reported while total Lewis acid site counts agreed with those measured by pyridine (ε(Sn; 1451 cm –1 ): 1.58 ± 0.16) on six different Sn-Beta zeolites. IMECs measured for IR peaks reflecting pyridine bound to Lewis acidic Hf sites (ε(Hf; 1448 cm –1 ): 1.54 ± 0.21) and CD 3 CN bound to open (ε(Hf; 2313 cm –1 ): 2.40 ± 0.22) and closed (ε(Hf; 2307 cm –1 ): 3.55 ± 0.41) Hf sites, gave similar counts for the total number of Lewis acidic sites across six Hf-Beta zeolites (Si/Hf = 100–413). Consistent with previous reports with Sn-Beta catalysts where open Sn sites are responsible for catalytic turnover, apparent first and zero-order MPVO rate constants (0.01–1 M cyclohexanone in 2-butanol; per total Hf, 373 K) correlated with the total number of open Hf sites, per total Hf, but not with the total number of closed Hf sites or total Lewis acid site counts. Measured initial MPVO rates (0.1 M cyclohexanone in 2-butanol, per open Hf, 373 K) were ~25x higher on hydrophobic Hf-Beta-F than on hydrophilic Hf-Beta-OH zeolites. Overall, the apparent first-order MPVO rate constants (2-butanol solvent, per open Hf, 373 K) were ~6x higher on Hf-Beta-F than on Hf-Beta-OH zeolites. The characterization methods reported here enable normalization of MPVO turnover rates on Sn- and Hf-Beta zeolites by their number of open sites. Finally, this enables performing quantitative rate comparisons across Lewis acid zeolites of varying active site identity, solvation, and pore topology used in liquid-phase catalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Unexpected Conformational Behavior of Poly(poly(ethylene glycol) methacrylate)-Poly(propylene carbonate)-Poly(poly(ethylene glycol) methacrylate) (PPEGMA-PPC-PPEGMA) Amphiphilic Block Copolymers in Micellar Solution and at the Air-Water Interface

Self-assemblies (bulk micelles and Langmuir monolayers) of a new amphiphilic block copolymer, poly(poly(ethylene glycol) methacrylate)-poly(propylene carbonate)-poly(poly(ethylene glycol) methacrylate) (PPEGMA-PPC-PPEGMA), were investigated in dilute aqueous solution and at the air-water interface. An important feature that distinguishes PPEGMA-PPC-PPEGMA from conventional linear PEG-based polymer surfactants is that in the hydrophilic PPEGMA block the PEG moieties exist as side chains attached to the poly(methacrylate) (PMA) backbone. This study was performed using three PPEGMA-PPC-PPEGMA samples having an identical PPC molecular weight (5.6 kDa) and different PPEGMA molecular weights (7.3, 2.8 and 2.1 kDa on either side) (named as “G7C6G7”, “G3C5G3”, and “G2C6G2”, respectively). Cryo-TEM images revealed that G2C6G2 micelles form large clusters, whereas G7C6G7 micelles exist as unimers; the behavior of G3C6G3 is intermediate. The average core surface distance between two adjacent G2C6G2 micelles in a cluster was estimated to be only about 3.7 nm, which suggests that in the micelle corona layer only the PEG side chains (but not the PMA backbone) exist as hydrated brush chains. A calculation showed that at the small micelle separation distance observed, the van der Waals attractive forces become significant, and are thus likely responsible for the cluster formation. Steady shear rheometry measurements confirmed that G2C6G2 micelles are indeed only weakly bound in clusters, and these micelle clusters are thus prone to breakup even under mild steady shear. The micelle breakup force estimated from the shear viscosity data is in reasonable agreement with an estimate obtained from the theoretical van der Waals interaction potential. Langmuir monolayers formed at the air-water interface by PPEGMA-PPC-PPEGMA were also characterized; surface pressure-area measurements were performed. Detailed features of the surface pressure-area isotherms further supported that only the PEG side chains are hydrated in the subphase, while the PMA backbone remains unhydrated and situated on the water surface.

Lee, Jaewon↗
DOE OSTI2020

Ionic complexation of endblock-sulfonated thermoplastic elastomers and their physical gels for improved thermomechanical performance

Thermoplastic elastomers (TPEs) composed of nonpolar triblock copolymers constitute a broadly important class of (re)processable network-forming macromolecules employed in ubiquitous commercial applications. Physical gelation of these materials in the presence of a low-volatility oil that is midblock-selective yields tunably soft TPE gels (TPEGs) that are suitable for emergent technologies ranging from electroactive, phase-change and shape-memory responsive media to patternable soft substrates for flexible electronics and microfluidics. Many of the high-volume TPEs used for these purposes possess styrenic endblocks that are inherently limited by a relatively low glass transition temperature. To mitigate this shortcoming, we sulfonate and subsequently complex (and physically crosslink) the endblocks with trivalent Al3+ ions. Doing so reduces the effective hydrophilicity of the sulfonated endblocks, as evidenced by water uptake measurements, while concurrently enhancing the thermomechanical stability of the corresponding TPEGs. Chemical modification results, as well as morphological and property development, are investigated as functions of the degree of sulfonation, complexation and TPEG composition. (C) 2020 Published by Elsevier Inc.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Phase diagrams and microstructures of aqueous short alkyl chain polyethylene glycol ether carboxylate and carboxylic acid triblock surfactant solutions

The surfactant C 8 Eo 8 CH 2 COOH (Akypo LF2) and its salts have a small hydrophobic and a significantly longer hydrophilic part. As a consequence, there must be a significant steric constraint, once these surfactant molecules form micelles. In addition, the partially charged headgroups should bring some additional fine-tuning via electrostatic interactions to this "essentially non-ionic" surfactant. Experiments: Phase diagrams of binary mixtures of water and C 8 Eo 8 CH 2 COOH are established over large concentration and temperature ranges, also at different pHs and in the presence of sodium and calcium ions. Surface tensions and osmotic pressures are measured to understand the systems. To evaluate the microstructures, also Dynamic Light Scattering and Small-Angle X-ray Scattering are performed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗