Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “graphite anodes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Revealing causes of macroscale heterogeneity in lithium ion pouch cells via synchrotron X-ray diffraction

Heterogeneous battery performance is a critical issue for maximization of cell lifetime capacity and safety. Using high energy synchrotron X-ray diffraction, the influence of charge rate, voltage limit, uneven stack pressure, and gas generation on the lithium transport properties was quantified in single-layer graphite/LiNi 0.5 Mn 0.3 Co 0.2 O 2 pouch cells. A freshly formatted cell tracked in operando during initial fast charge cycles indicated variable position-dependent performances, while lateral mapping showed a significant fast charge (6C) heterogeneity compared to slow charge (C/2). Pressure effects were non-dominant compared to charge rate. Maps of previously aged and rested cells indicate that lateral heterogeneity slowly equilibrates at rest, but regenerates upon further cycling at fast charge rate. Furthermore, an unformatted cell was mapped at charge and discharge during its first formation cycle to analyze the effect of byproduct gases on the heterogeneous lithium transport. Gas was observed as randomly interspersed “bubbles” which locally hindered lithium intercalation and caused significant heterogeneity. Electrode architectures and charging protocols that promote homogeneous intercalation are critical for predictable high-performance and long-life batteries.

25 ENERGY STORAGE↗
DOE OSTI2021

Role of silicon-graphite homogeneity as promoted by low molecular weight dispersants

This study explores low molecular weight polymers with the same chemical repeat structure as high molecular weight poly acrylic acid (PAA) and lithium poly acrylic acid (LiPAA) binders which act as a dispersant to improve the silicon-graphite electrode performance. The electrodes which utilize LiPAA as a dispersant perform, on average, the best with respect to the maximum capacity (compared to theoretical), rate performance, and capacity retention with time. These electrodes also have the poorest dispersion of binder, indicating that the poor binder dispersion is essential to electrode performance. In contrast, this study shows that electrodes formulated using PAA had good dispersion and performs the worst in cycling. Finally, this work demonstrates that the binder is not uniformly distributed in the electrode, but rather resides in local regions. Overall, the results indicate these regions accommodate volume expansion during cycling.

25 ENERGY STORAGE↗
DOE OSTI2025

Demonstration of and future perspective on scaling ultrafast-laser-ablation microstructuring of Li-ion battery electrodes to roll-to-roll production and large-format cells

This work demonstrates integration of an ultrafast laser onto a roll-to-roll machine, the laser structuring of a double-sided, 700 m long roll of graphite battery anode and its subsequent manufacture into 27 Ah prismatic cells. The electrode was ablated with a novel hybrid-microstructure composed of both hexagonally arranged pores for enhanced rate performance and channels for fast electrolyte wetting. Subsequently, this anode and a non-ablated baseline anode are paired with an NMC111 cathode for cell building and electrochemical characterization. Compared to the baseline, laser ablated cells demonstrated a reduction in soaking time of at least 60%, an improvement in fast charge capability with >30% more capacity accepted during 6C charging, and an extension of cycle life of >40% during 0.5C cycling. Further, a perspective is provided on scaling ultrafast laser ablation of battery electrodes to industrial throughputs. Additionally, lessons learned from this pilot-scale demonstration are provided in regards to optical architecture, debris removal, and system control. A techno-economic analysis is used to demonstrate that laser ablation can be integrated into existing electrode manufacturing facilities with only ≈$\$$1.3 per kWh increase (≈2%) in manufacturing cost. Preemptive electrode design for laser ablation is discussed as a further method for enhancing performance. Finally, an analysis of available laser systems and beam-scanning architectures is used to determine design requirements to scale process throughput to a state-of-the-art speed of 50 m min −1 . This analysis demonstrates that laser ablating Li-ion battery electrodes has multiple benefits to manufacturing and battery performance, that the technology already exists to achieve high laser-ablation throughputs, and that integrating ultrafast laser ablation to electrode manufacturing will not create a cost or processing bottleneck.

25 ENERGY STORAGE↗
DOE OSTI2025

Revealing the roles of the solid–electrolyte interphase in designing stable, fast-charging, low-temperature Li-ion batteries

Designing the solid–electrolyte interphase (SEI) is critical for stable, fast-charging, low-temperature Li-ion batteries. Fostering a “fluorinated interphase,” SEI enriched with LiF, has become a popular design strategy. Although LiF possesses low Li-ion conductivity, many studies have reported favorable battery performance with fluorinated SEIs. Such a contradiction suggests that optimizing SEI must extend beyond chemical composition design to consider spatial distributions of different chemical species. In this work, we demonstrate that the impact of a fluorinated SEI on battery performance should be evaluated on a case-by-case basis. Sufficiently passivating the anode surface without impeding Li-ion transport is key. We reveal that a fluorinated SEI containing excessive and dense LiF severely impedes Li-ion transport. In contrast, a fluorinated SEI with well-dispersed LiF (i.e., small LiF aggregates well mixed with other SEI components) is advantageous, presumably due to the enhanced Li-ion transport across heterointerfaces between LiF and other SEI components. An electrolyte, 1 M LiPF 6 in 2-methyl tetrahydrofuran (2MeTHF), yields a fluorinated SEI with dispersed LiF. This electrolyte allows anodes of graphite, μSi/graphite composite, and pure Si to all deliver a stable Coulombic efficiency of 99.9% and excellent rate capability at low temperatures. Pouch cells containing layered cathodes also demonstrate impressive cycling stability over 1,000 cycles and exceptional rate capability down to −20 °C. Through experiments and theoretical modeling, we have identified a balanced SEI-based approach that achieves stable, fast-charging, low-temperature Li-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2021

Highly Concentrated Electrolytes: Electrochemical and Physicochemical Characteristics of LiPF 6 in Propylene Carbonate Solutions

Highly concentrated electrolytes (HCEs) based on LiPF 6 in propylene carbonate (PC) have been examined as lithium-ion battery electrolytes. These HCEs have lower ionic conductivities and higher viscosities than ethylene carbonate (EC) electrolytes with 1.2 M LiPF 6 , but they have higher Li + ion transference numbers. Electrochemical cycling behaviour of LiNi 0.8 Co 0.015 Al 0.05 O 2 //graphite cells with 3.2 M LiPF 6 in PC resembles that of cells with EC-based electrolytes; the HCE cells have higher impedance, which can be lowered by increasing test temperature. By employing Raman and infrared spectroscopy, combined with density functional theory and ab initio molecular dynamics simulations, we reveal that the Li + solvation structure and speciation are key factors that determine cell performance. Two distinct regimes are observed as a function of salt concentration—in the conventional regime, the solvation number (SN) is mostly constant, while in the HCE regime it decreases linearly. Graphite exfoliation is suppressed only at very high salt concentrations ( > 2.4 M), where [ PC ] free /[Li + ] < 1 and P F 6 − f r e e > P C f r e e . Results from the Advanced Electrolyte Model indicate that Li + desolvation improves at higher LiPF 6 concentrations, thereby mitigating PC co-intercalation into the graphite. However, Li + ion transport is hindered in the HCEs, which increases impedance at both the oxide-positive and graphite-negative electrodes.

25 ENERGY STORAGE↗
DOE OSTI2021

Time-Resolved X-ray Operando Observations of Lithiation Gradients across the Cathode Matrix and Individual Oxide Particles during Fast Cycling of a Li-Ion Cell

Lithiated transition metal oxides serve as active materials in the positive electrode (cathode) of lithium-ion cells. During electrochemical cycling, lithium ions intercalate and deintercalate into these oxide particles. This behavior causes two types of lithiation gradients to emerge: (i) a bulk gradient across the depth of the cathode matrix (averaged over individual oxide particles) and (ii) a microscopic gradient across the particles themselves, which also depends on their location in the electrode. Here we show how both gradients can be studied using operando X-ray diffraction during 4C charge and 4C discharge. The oxide (de)lithiation is estimated from the unit cell parameters by indexing the X-ray diffraction spectra. By fitting the lithiation profiles with orthogonal polynomials, the bulk gradients across the electrode thickness are quantified. These gradients develop as the current flows through the cell and dissipate during open-circuit and potentiostatic-hold periods. Further details of lithiation dynamics can be obtained through shape analysis of the Bragg peaks. In particular, from electrochemical model simulations, we show that the width and skewness of the (003) peak track (de)lithiation fronts moving across the individual oxide particles.

(003) peak↗
DOE OSTI2022

Electrochemical Modeling and Experimental Verification of Lithiation Gradients in Oxide Cathodes of Lithium-Ion Cells

Lithiated nickel-cobalt-manganese oxides, such as NCM523, are used in the positive electrode (cathode) of Li-ion cells. Using operando X-ray diffraction profilometry, lithiation gradients in the cathode matrix can be observed and quantified by expansion into Legendre polynomials with time-dependent weights. These weights (referred to as gradients) increase in magnitude when electric current flows through the cell, decrease during potentiostatic hold and finally relax to zero when the current is interrupted during open circuit rest. Both physics-based electrochemical models and operando X-ray experiments suggest that the time constants for gradient growth and abatement are primarily determined by ionic diffusion in the oxide particles, which in turn depends on their lithium content. In contrast, the magnitude of gradients depends mainly on the applied current. The X-ray profilometry provides a way of directly probing the formation and disappearance of Li gradients across the cathode during fast cycling, which can help to diagnose the effects of material degradation in the cells.

25 ENERGY STORAGE↗
DOE OSTI2024

Examining Performance Loss Mechanisms in Lithium-Ion Batteries with the High-Voltage Mn-Rich Spinel Positive Electrodes

The high-voltage spinel, with the nominal composition of LiNi 0.5-x Mn 1.5+x O 4 (LNMO), could be a sustainable alternative to the layered-oxide positive electrodes used in lithium-ion batteries. However, commercial acceptance has been limited as LNMO cells display rapid performance loss during cycling. To examine reasons for this loss we prepared cells with LNMO-based positive and either graphite or lithium titanate (LTO) based negative electrodes. Our initial cells displayed high impedance and rapid impedance rise during cycling. Adding single walled carbon nanotubes in the positive lowered initial cell impedance but impedance increased during cycling because of coating delamination from the Al foil. Using a primed Al current collector solved the delamination problem: cells with this current collector showed only a small impedance rise. Regarding capacity, cells with the LTO negative showed higher initial capacities and smaller fade. Our data indicate that cell capacity retention is determined by reduction reactions at the negative electrode that lower capacity and oxidation reactions at the positive electrode that increase capacity: both types of reactions deplete the cell electrolyte during extended cycling. All things considered, species generated at high voltages, either in the electrolyte or at the LNMO electrode, drive cell capacity fade.

25 ENERGY STORAGE↗
DOE OSTI2021

Design Considerations for Fast Charging Lithium Ion Cells for NMC/MCMB Electrode Pairs

Lithium ion cells that can be quickly charged are of critical importance for the continued and accelerated penetration of electric vehicles (EV) into the consumer market. Considering this, the U.S. Department of Energy (DOE) has set a cell recharge time goal of 10–15 min. The following study provides an investigation into the effect of cell design, specifically negative to positive matching ratio (1.2:1 vs. 1.7:1) on fast charging performance. By using specific charging procedures based on negative electrode performance, as opposed to the industrial standard constant current constant voltage procedures, we show that the cells with a higher N:P ratio can be charged to ~16% higher capacity in the ten-minute time frame. Cells with a higher N:P ratio also show similar cycle life performance to those with a conventional N:P ratio, despite the fact that these cells experience a much higher irreversible capacity loss, leading to a lower reversible specific capacity.

25 ENERGY STORAGE↗
DOE OSTI2020

Electrochemical behavior and separation of iodide in molten LiF-NaF-KF melt

This work studied the electrochemical behavior of iodide in molten LiF-NaF-KF mixture and the separation of iodide from the molten salt at 973 K using a graphite working electrode. The cyclic voltammetry (CV) and chronoamperometry (CA) measurements indicated an anodic passivation layer was formed on the graphite electrode in this melt and the layer blocked the charge transfer across the electrolyte/electrode interface. However, the added I- ions could pass through the passivation layer and were oxidized at the graphite electrode. The characterization of the obtained products proved that iodide ions was efficiently oxidized to I2 gas during electrolysis. Furthermore, the graphite anode showed excellent stability without any obvious change in dimensions after electrolysis, which showed the high current efficiency of I2 evolution reaction. Thus, the graphite electrode was possible to be served as an excellent anode to separate other anions (such as Br) from molten fluoride salts.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Siloxane Deposition on the Ni-YSZ Solid Oxide Fuel Cell Anode Exposed to Bio-Syngas

Siloxane, a common contaminant present in biogas, is known for adverse effects on cogeneration prime movers. In this study, the siloxane deposition products and mechanism in the solid oxide fuel cell nickel-yttria stabilized zirconia (Ni-YSZ) anode are investigated analytically and experimentally. An SOFC with Ni-YSZ anode and pure Ni/YSZ pellets were exposed to a simulated biogas-reformate fuel with octamethylcyclotetrasiloxane (D4) contamination at 750 °C. The electrochemical characterization results show that the SOFCs performance degradation caused by D4 contamination is irreversible. Morphology and XRD results illustrate that silicon and carbon deposition can both be detected in the anode and pellets. Graphite, SiC and SiO2 are all possible products based on the results of XRD test. Here, according to the formation of graphite and SiC, the new mechanism suggests that carbon is also an essential factor in siloxane contamination of Ni-YSZ anodes besides silicon, which can be explained by the catalytic and electrochemical analysis.

25 ENERGY STORAGE↗
DOE OSTI2024

Exploring Lead Zirconate Titanate, the Potential Advancement as an Anode for Li-Ion Batteries

Graphite, widely adopted as an anode for lithium-ion batteries (LIBs), faces challenges such as an unsustainable supply chain and sluggish rate capabilities. This emphasizes the urgent need to explore alternative anode materials for LIBs, aiming to resolve these challenges and drive the advancement of more efficient and sustainable battery technologies. The present research investigates the potential of lead zirconate titanate (PZT: PbZr 0.53 Ti 0.47 O 3 ) as an anode material for LIBs. Bulk PZT materials were synthesized by using a solid-state reaction, and the electrochemical performance as an anode was examined. A high initial discharge capacity of approximately 686 mAh/g was attained, maintaining a stable capacity of around 161 mAh/g after 200 cycles with diffusion-controlled intercalation as the primary charge storage mechanism in a PZT anode. These findings suggest that PZT exhibits a promising electrochemical performance, positioning it as a potential alternative anode material for LIBs.

25 ENERGY STORAGE↗
DOE OSTI2022

Analytical and Numerical Analysis of Lithium Plating Onset in Single and Bilayer Graphite Electrodes during Fast Charging

Lithium plating is commonly observed in anodes charged at fast rates, and can lead to capacity loss and battery safety issues. The increased risk of plating has been attributed to transport limitations, and architectured electrodes may reduce plating risk. However, while theoretical studies have shown that reaction non-uniformity arises due to interplay of transport limitations, anode open circuit voltage behavior and reaction kinetics, its effect on lithium plating has not been studied. We use analytic and numerical simulations to predict onset of plating in graphite anode half-cells at high C-rates and demonstrate how anodes with layered porosities can delay plating. Simplified analytical models identify trends for plating onset and predictions are calibrated against numerical models. A calibrated numerical model of graphite demonstrates qualitative agreement with analytical model predictions. This reaction inhomogeneity mechanism occurs in the absence of lithium ion depletion, indicating that these mechanisms may contribute to capacity loss independently or simultaneously. A bilayer model of graphite exhibits delayed plating onset, and an optimization procedure is presented. This theoretical work presents quantitative and mechanistic insight on how reaction inhomogenity affects lithium metal plating onset and can be used as a guide to engineer anodes resistant to lithium plating.

Mijailovic, Aleksandar S.↗
DOE OSTI2023

Interfacial pressure improves calendar aging of lithium metal anodes

Lithium (Li) metal is a promising anode because its theoretical specific capacity is approximately ten times larger than graphite. However, Li anodes suffer from long-term capacity fade due to Li stranding (becoming electronically disconnected) and electrolyte decomposition. Applied interfacial pressure has been shown to improve Li anode cycling, likely due to reincorporating stranded or “dead” Li into the anode. Calendar aging can also lead to Li capacity loss due to electrolyte decomposition/Li corrosion and the formation of stranded Li. Some research suggests that calendar aging during cycling results in reversible capacity losses due to Li stranding and reconnection. We here investigate the effect of applied interfacial pressure on Li anode calendar aging during cycling with incorporated rest steps in a localized high-concentration electrolyte (LHCE) to understand if pressure can mitigate stranded Li formation during rest by manipulating the Li morphology. Pouch cells exhibit more stable cycling and denser Li deposits between 10 kPa and 1,000 kPa of applied pressure compared to no applied pressure. Despite drops in CE during periodic rest cycles, the average cumulative lost capacity and average coulombic efficiency (CE) of cells over 50 cycles show that cells aged with incorporated rest steps perform similarly to cells cycled without added rests. This similar average CE suggests that dead Li is largely responsible for drops in CE during rest rather than irreversible Li corrosion and that the dead Li can be reconnected in subsequent cycling. The addition of a lithiophilic ZnO coating to the Cu working electrode increases the adhesion and coverage of Li deposits at low pressures and improves CE during the first cycle.

25 ENERGY STORAGE↗
DOE OSTI2021

Quantification of heterogeneous, irreversible lithium plating in extreme fast charging of lithium-ion batteries

Realization of extreme fast charging (XFC, ≤15 minutes) of lithium-ion batteries is imperative for the widespread adoption of electric vehicles. However, dramatic capacity fading is associated with XFC, limiting its implementation. To quantitatively elucidate the effects of irreversible lithium plating and other degradation mechanisms on the cell capacity, it is important to understand the links between lithium plating and cell degradation at both the local and global (over the full cell) scales. Here, we study the nature of local lithium plating after hundreds of XFC cycles (charging C-rates ranging from 4C to 9C) in industrially-relevant pouch cells using spatially resolved X-ray diffraction. Our results reveal a spatial correlation at the mm scale between irreversible lithium plating on the anode, inactive lithiated graphite phases, and local state-of-charge of the cathode. In regions of plated lithium, additional lithium is locally and irreversibly trapped as lithiated graphite, contributing to the loss of lithium inventory (LLI) and to a local loss of active anode material. The total LLI in the cell from irreversibly plated lithium is linearly correlated to the capacity loss in the batteries after XFC cycling, with a non-zero offset originating from other parasitic side reactions. Finally, at the global (cell) scale, LLI drives the capacity fade, rather than electrode degradation. We anticipate that the understanding of lithium plating and other degradation mechanisms during XFC gained in this work will help lead to new approaches towards designing high-rate batteries in which irreversible lithium plating is minimized.

25 ENERGY STORAGE↗
DOE OSTI2025

Study of the Design and Characteristics of a Modified Pulsed Plasma Thruster with Graphite and Tungsten Trigger Electrodes

The paper presents experimental results for a modified pulsed plasma thruster (PPT) with solid propellant, using a coaxial anode–cathode design. Graphite from pencil leads served as propellant, and a tungsten trigger electrode was tested to reduce carbonization effects. Experiments were performed in a vacuum chamber at 0.001 Pa, employing diagnostics such as discharge current/voltage recording, power measurement, ballistic pendulum, time-of-flight (TOF) method, and a Faraday cup. Current and voltage waveforms matched an oscillatory RLC circuit with variable plasma channel resistance. Key discharge parameters were measured, including current pulse duration/amplitude and plasma channel formation/decay dynamics. Impulse bit values, obtained with a ballistic pendulum, reached up to 8.5 μN·s. Increasing trigger capacitor capacitance reduced thrust due to unstable “pre-plasma” formation and partial pre-discharge energy loss. Using TOF and Faraday cup diagnostics, plasma front velocity, ion current amplitude, current density, and ion concentration were determined. Tungsten electrodes produced lower charged particle concentrations than graphite but offered better adhesion resistance, minimal carbonization, and stable long-term performance. The findings support optimizing trigger electrode materials and PPT operating modes to extend lifetime and stabilize thrust output.

Faraday cup↗
DOE OSTI2020

TiO2 Nanocrystal-Framed Li 2 TiSiO 5 Platelets for Low-Voltage Lithium Battery Anode

Titanium-based anode materials are attracting considerable attention for use in high-performance lithium-ion batteries, but the compromised energy density caused by high voltage plateaus and unsatisfactory capacities severely retards their practical applications. Herein, a molten-salt synthesis of Li 2 TiSiO 5 crystalline platelets and a subsequent selective facet modification by in situ growth of TiO 2 nanocrystal frames are facilely achieved. The discharge voltage plateau at around 0.5 V renders the Li 2 TiSiO 5 anode safe compared with graphite and confers a high energy density compared with zero-strain Li 4 Ti 5 O 12 anode. With the optimized size, structure, and content of modified TiO2 nanocrystals associated with the exposed (001) plane of Li 2 TiSiO 5 , the Li 2 TiSiO 5 -based anodes can deliver a capacity of above 300 mAh g -1 , enhanced rate performance, and a capacity retention of 66% after 10 000 cycles. In situ X-ray diffraction and ex situ transmission electron microscopy have demonstrated the structural stability of the anodes upon charge/discharge. Further theoretical calculation reveals 3D migration paths of Li + ions in Li 2 TiSiO 5 . The selective modification of in situ grown TiO2 nanocrystals on certain facets of crystallites opens a new door for the development of electrode materials possessing superior electrochemical properties.

anodes↗
DOE OSTI2023

Interfacial Issues and Modification of Solid Electrolyte Interphase for Li Metal Anode in Liquid and Solid Electrolytes

Abstract The high energy density required for the next generation of lithium batteries will likely be enabled by a shift toward lithium metal anode from the conventional intercalation‐based anode such as graphite. However, several critical challenges for Li metal originate from its highly reactive nature and the hostless reaction of deposition and stripping impede the practical use of Li metal as an anode. The role of the solid electrolyte interphase (SEI) is very important for the Li metal anode where the SEI must protect the dynamically changing surface of the Li metal. Since the SEI‐generating reaction mechanisms for the two different electrolyte systems, liquid and solid, are considerably different, the SEI layers formed between the Li metal and the electrolytes in the two electrolyte systems have substantially different properties, causing different interfacial issues. Inhibition of the interfacial problems requires different strategies to reinforce the SEI layer for each of the electrolyte systems. However, the differences in the two electrolyte systems have not been clearly compared in the prior literature. In this report, the interfacial issues for the two different electrolyte systems are compared and different strategies for SEI modification are provided to overcome the issues.

25 ENERGY STORAGE↗