Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “gain”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Spectral narrowing and broadening of Cr:ZnS/Se laser oscillation due to mode competition and spatial hole burning in the gain element

In this paper, we demonstrate the laser characterization of Cr:ZnS/Se polycrystalline gain media in non-selective unpolarized, linearly polarized, and twisted mode cavities. Lasers were based on post-growth diffusion-doped, commercially available antireflective-coated Cr:ZnSe and Cr:ZnS polycrystals with a length of 9 mm. The spectral output of lasers based on these gain elements in non-selective unpolarized and linearly polarized cavities was measured to be broadened to ∼20-50 nm due to the spatial hole burning (SHB) effect. SHB alleviation in the same crystals was realized in the “twisted mode” cavity, with linewidth narrowing to ∼80-90 pm. Both broadened and narrow-line oscillations were captured by adjusting the orientation of intracavity waveplates with respect to facilitated polarization.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Dual-wavelength channel GHz repetition rate mode-locked VECSEL cavities sourced from a common gain medium

Mode-locked vertical external cavity semiconductor lasers are a unique class of nonlinear dynamical systems driven far from equilibrium. We present a novel, to the best of our knowledge, experimental result, supported by rigorous microscopic simulations, of two coexisting mode-locked V-cavity configurations sourced by a common gain medium and operating as independent channels at angle controlled separated wavelengths. Microscopic simulations support pulses coincident on the common gain chip extracting photons from a nearby pair of coexisting kinetic holes burned in the carrier distributions.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Energy gain in a two-gap RF cavity

Velocity of a deeply non-relativistic particle can change during its acceleration inside an RF cavity significantly enough to cause a deviation of the energy gain from a linear model. This paper derives formulae for corrections to the energy gain in a two-gap RF cavity calculated by taking into account this velocity change in the next approximation. Then, the results are compared with direct particle tracking of an HWR cavity used at the PIP2IT test accelerator. The formulae significantly extend the range of parameters where analytical calculations work with a good accuracy. The approach is applied to two aspects of cavity phasing.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Technical Documents for Gateway for Accelerated Innovation in Nuclear (GAIN)

The Gateway for Accelerated Innovation in Nuclear (GAIN) provides the nuclear energy community with access to the technical, regulatory, and financial support necessary to move new or advanced nuclear reactor designs toward commercialization. GAIN provides the nuclear community with a single point of access to the broad range of capabilities (i.e., people, facilities, materials, and data) across the U.S. Department of Energy (DOE) complex and its National Lab capabilities. The Fast Flux Test Facility (FFTF) is the most recent liquid metal reactor (LMR) to be designed, constructed, and operated by DOE. The 400-MWt sodium-cooled, fast-neutron flux reactor plant was designed for irradiation testing of nuclear reactor fuels and materials for liquid metal fast breeder reactors. Following the demise of the breeder reactor program in the United States, FFTF continued to play a key role in providing a test bed for demonstrating performance of advanced fuel designs and demonstrating operation, maintenance, and safety of advanced liquid metal reactors. The FFTF Program provides valuable information for potential follow-on reactor projects in the areas of plant system and component design, component fabrication, fuel design and performance, reactor control, prototype testing, and site construction. This report provides documents related to three important aspects of FFTF design and operation: 1) irradiation behavior of structural alloys and absorber materials, 2) thermohydraulics of rod bundles (i.e., coolant mixing), and 3) natural circulation heat transfer in the areas of modeling and validation. These technical documents are believed to be of interest to the nuclear industry and in particular to designers of new liquid metal reactors.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Pressure Gain, Stability, and Operability of Methane/Syngas Based RDEs Under Steady and Transient Conditions (Final Project Report)

The scope of this work addresses key issues associated with losses associated with the detonation wave and other processes internal to the RDE operation, as well as it develops modeling tools for the evaluation of these losses and exhaust emissions in RDEs. The main challenge in studying RDEs is that RDE performance is highly reliant on the specifics of the design so much so that simple/canonical systems alone cannot provide useful engineering information, but practical RDE designs are sufficiently complex and involve extreme operational environments that detailed access either experimentally (laser diagnostics, for instance) or computationally (direct numerical simulations) are as yet to become practical. To overcome this challenge, we have conducted a combined experimental/simulation/analytical study investigating key phenomena that control the characteristics of operation of RDEs. As a result, the study has developed tools and methods that can be used to evaluate performance and design approaches using reduced-physics models, with the assumptions validated using detailed simulations, and the model prediction tested using experimental observations. The specific objectives of the research were: (1) Develop and demonstrate a low-loss fully axial injection concept, taking advantage of stratification effects to alter the detonation structure and position the wave favorably within the combustor; (2) Obtain stability and operability characteristics of an RDE across operating conditions to aid in the development of operability and performance rules for the operations of other systems; and (3) Develop quantitative metrics for performance gain as well as quantitative description of the loss mechanisms through a combination of diagnostics development, reduced-order modeling, and detailed simulations. The work conducted here has made contribution on design of low-loss inlets that has broad application within the power generation industry for use with pressure gain combustion. The operability and stability of different designs, while focusing on axial air inlet designs, has been analyzed. The effect of nozzle and injection conditions was studied. Models and simulations of exhaust emissions, focusing on NOx emission has been developed and used to investigate how operation of the RDE affect NOx production using Lagrangian analysis of RDE simulations. This work has built on previous programs, with the goal of further understanding operation of RDEs and elevate the readiness of design consideration. In addition, a suite of diagnostic and modeling tools have been developed to obtain quantitative metrics on performance based on measurements, which can be readily transferred to other experimental configurations.

08 HYDROGEN↗
DOE OSTI2026

Solar-Tracker Diffuse-Response Algorithm for Balancing Energy Gain and Mechanical Wear in Photovoltaic Systems

Single-axis solar tracking maximizes photovoltaic energy production under clear-sky conditions; however, its effectiveness decreases under cloudy and overcast skies, where diffuse irradiance dominates and the optimal module orientation changes. Conventional tracking algorithms either neglect sky conditions or rely on simplified diffuse-response strategies that may trigger frequent tracker repositioning under variable cloud cover, leading to increased mechanical wear with marginal energy gains. This work proposes an enhanced diffuse-response tracking algorithm that explicitly accounts for both the intensity and temporal persistence of cloudiness. By requiring overcast conditions to persist for a minimum duration before reorienting the tracker to a diffuse-stow position, the proposed approach reduces unnecessary movements while preserving the benefits of diffuse-response operation. The algorithm is evaluated through numerical simulations based on historical meteorological data and validated using field measurements on monofacial and bifacial photovoltaic strings. The results show that the proposed strategy reduces excess tracker movement from 114% to 0.16% while maintaining nearly the same energy yield. Compared to a conventional diffuse-response algorithm, the associated energy reduction is minimal (≈0.17%) relative to the ≈0.37% yield gain observed at the studied location. These findings demonstrate that incorporating cloudiness duration enables a practical compromise between energy performance and tracker durability, particularly for monofacial photovoltaic systems.

14 SOLAR ENERGY↗
DOE OSTI2025

Fabrication of 4H-SiC Low Gain Avalanche Detectors (LGADs)

Low gain avalanche detectors (LGADs) offer high temporal resolution for high energy particle detection, which is critical for next generation experiments in hadron colliders. While silicon LGADs (Si-LGADs) have rapidly matured in the last decade, research into silicon carbide (SiC) LGADs has only recently begun. By accounting for fundamental differences in material properties and fabrication processes, we present a prototype device design and process flow for 4H-SiC LGADs with etch-based isolation. Critical steps of the process flow and their results are discussed, including plasma etching, passivation, and the formation of low resistivity contacts. Electrical characterization (I-V, C-V) shows sufficient depletion of the device structure to demonstrate low-gain charge carrier multiplication.

High Energy Physics↗
DOE OSTI2021

A High Gain Lens-Coupled On-Chip Antenna Module for Miniature-Sized Millimeter-Wave Wireless Transceivers

This paper presents high gain and compact Transmit/Receive (TX/RX) integrated antennas in a standard BiCMOS 130nm technology for millimeter-scale millimeter-wave (mm-wave) applications, including high data rate radios and high resolution radars. The proposed TX/RX antenna module utilizes an integrated dipole antenna for the receiver and a slot antenna for the transmitter, placed orthogonally. The achieved gain and radiation efficiency are 5.7dBi and 41.3% for the slot antenna, respectively, and 6dBi and 39% for the dipole antenna. The link budget is improved by 16dB by optimization on the geometry aswell as application of a high resistivity hemispheric silicon dielectric lens.

Engineering↗
DOE OSTI2023

Increased power gains from wake steering control using preview wind direction information

Abstract. Yaw controllers typically rely on measurements taken at the wind turbine, resulting in a slow reaction to wind direction changes and subsequent power losses due to misalignments. Delayed yaw action is especially problematic in wake steering operation because it can result in power losses when the yaw misalignment angle deviates from the intended one due to a changing wind direction. This study explores the use of preview wind direction information for wake steering control in a two-turbine setup with a wind speed in the partial load range. For these conditions and a simple yaw controller, results from an engineering model identify an optimum preview time of 90 s. These results are validated by forcing wind direction changes in a large-eddy simulation model. For a set of six simulations with large wind direction changes, the average power gain from wake steering increases from only 0.44 % to 1.32 %. For a second set of six simulations with smaller wind direction changes, the average power gain from wake steering increases from 1.24 % to 1.85 %. Low-frequency fluctuations are shown to have a larger impact on the performance of wake steering and the effectiveness of preview control, in particular, than high-frequency fluctuations. From these results, it is concluded that the benefit of preview wind direction control for wake steering is substantial, making it a topic worth pursuing in future work.

17 WIND ENERGY↗
NASA NTRS1966

Optical automatic gain channel

Automatic Gain Control /AGC/ channel automatically compensates for gain changes in the azimuth error channel due to time varying optical sight degrading effects. This system is useful in remote television monitors, automatic navigation systems, and surveying and mapping instrumentation.

Mrus, G.↗
NASA NTRS1968

Power consumption in acoustic amplifiers under conditions of maximum stable gain

Comparison is made of the power consumed and the acoustic amplification realized when a dc bias field is placed across a piezoelectric semiconductor and adjusted to amplify a microwave acoustic signal to the point where the forward gain is just equal to the reverse attenuation. This represents the maximum possible gain condition.

Johnson, V. R.↗
NASA NTRS1972

Pole placement with constant gain output feedback

Given a linear time invariant multivariable system with m inputs and p outputs, it was shown that p closed loop poles of the system can be preassigned arbitrarily using constant gain output feedback provided (A circumflex, B circumflex) is controllable. These data show that if (A circumflex, B circumflex, C circumflex) is controllable and observable, and Rank B circumflex = m, Rank C circumflex = p, then max (m,p) poles of the system can be assigned arbitarily using constant gain output feedback. Further, it is shown that in some cases more than max (m,p) poles can be arbitrarily assigned. A least square design technique is outlined to approximate the desired pole locations when it is not possible to place all the poles.

Sridhar, B.↗
NASA NTRS1972

Gain calibration of a horn antenna using pattern integration

Gain measurement of a horn antenna using three different techniques is discussed. The methods include a two-antenna insertion loss measurement, a pattern integration method, and a near-field measurement method. The application of the pattern integration method is considered, as well as the evaluation of the near-field gain correction factors for the horn, which are determined by a method based directly on measured data. This method involves a spherical wave expansion of the experimental radiation pattern of the specific antenna being tested, rather than evaluation of an assumed analytical model. The spherical wave expansion is also compared to experimental near-field pattern data.

Ludwig, A. C.↗
NASA NTRS1972

Helicopter payload gains utilizing water injection for hot day power augmentation

An analytical investigation was undertaken to assess the gains in helicopter mission payload through the use of water injection to produce power augmentation in an altitude-hot day environment. Substantial gains are shown for two representative helicopters, the UH-lH and CH-47B. The UH-lH payload increased 86.7 percent for a 50 n.mi. (92.6 km) radius mission involving two out-of-ground effect (OGE) hover take-offs of 2 minutes each at 5000 ft. (1525 m) 35 C ambient conditions. The CH-47B payload increased 49.5 percent for a 50 n.mi. (92.6 km) radius mission with sling loaded cargo as the outbound payload and a 3000 lb. (1360 kg) internal cargo on the return leg. The mission included two 4 min. OGE hovers at 6000 ft. (1830 m) 35 C. An improvement in take off performance and maximum performance climb also resulted as a consequence of the OGE hover capability and higher maximum power available.

Stroub, R. H.↗
NASA NTRS1971

Gain kinetics of CO2 gasdynamic laser mixtures at high pressure.

Description of a combined analytical and experimental investigation of rapidly expanded CO2 laser mixtures. Study of the vibrational kinetics indicates that population inversions with high vibrational energy density can be produced at high pressures by utilizing low (starved) concentrations of CO2. Scaling laws for predicting the gain of starved systems are developed. A description is given of gain measurements carried out using a CO2 laser to probe the flow in a nozzle at the point where the Mach number is approximately four. Population inversions at static pressures as high as about 1 atm have been observed and found to be in reasonable agreement with predictions.

Christiansen, W. H.↗
NASA NTRS1972

A curve-fitting technique for the determination of gain and saturation intensity in homogeneously-broadened gas lasers: Application to a waveguide CO2 laser

A least squares curve-fitting algorithm is derived which allows the simultaneous estimation of the small signal gain and the saturation intensity from an arbitrary number of data points relating power output to the incidence angle of an internal coupling plate. The method is used to study the dependence of the two parameters on tube pressure and discharge current in a waveguide CO2 laser having a 2 mm diameter capillary. It is found that, at pressures greater than 28 torr, rising CO2 temperature degrades the small signal gain at current levels as low as three milliamperes.

Degnan, J. J.↗
NASA NTRS1973

Computer simulation of space station computer steered high gain antenna

The mathematical modeling and programming of a complete simulation program for a space station computer-steered high gain antenna are described. The program provides for reading input data cards, numerically integrating up to 50 first order differential equations, and monitoring up to 48 variables on printed output and on plots. The program system consists of a high gain antenna, an antenna gimbal control system, an on board computer, and the environment in which all are to operate.

Beach, S. W.↗