Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fuel swelling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

A novel approach to mitigating the potential release of radioisotopes under fire conditions - enhancing fire resiliency of radiological contamination fixatives during deactivation & decommissioning activities

Savannah River National Laboratory (SRNL), in close collaboration with the Florida International University Applied Research Center (FIU ARC), successfully executed a technology development activity on behalf of the Department of Energy, Office of Environmental Management (DOE EM). The purpose of the activity was to improve the capability of fixative technologies in immobilizing residual contamination when exposed to thermal stressors as postulated in accident scenarios in Basis for Interim Operations (BIO) documents across the DOE EM complex. The effort resulted in the test and evaluation of a down-selected, commercial-off-the-shelf (COTS) intumescent technology in a radioactive environment at the Savannah River Site (SRS) Building 235-F Plutonium Fuel Form (PuFF) Facility and highlighted the potential use of this technology as a stand-alone, fire retardant fixative. Furthermore, this activity highlighted significant shortfalls in common fixatives currently used to support decommissioning activities and brought to the forefront the need for a methodical, uniformed approach to certifying fixative technologies for operational use in Deactivation and Decommissioning (D&D) activities. An essential component of this research was to evaluate the state of industry fixatives currently in use and set the foundation for comparison to alternative technological solutions. A baseline of five (5) commonly used fixatives and decontamination gels (hereafter collectively referred to as fixatives) was conducted, and notable shortfalls and deficiencies were revealed, particularly when exposed to thermal, water, and other environmental stressors. At temperatures as low as 300 °F - 400 °F (148.89 °C – 204.44 °C), all commonly used fixatives melted from the substrates within 3-5 minutes of exposure, resulting in contaminant transport. Significant degradation in terms of mass loss, desiccation, and off-gassing occurred, and the chemical breakdown of the polymer was so complete researchers assessed there would likely have been a release of residual contamination. Additional vulnerabilities became evident when exposed to water immersion and high humidity; existing fixatives took up water, swelling and frequently delaminating from the substrate, once again increasing the likelihood of a contaminant release.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

FFTF HT9 Cladding Microstructure Characterization

The sodium-cooled fast reactor (SFR) is a promising candidate for next generation nuclear reactors, operating at extreme conditions which include high temperatures (>500?C core outlet temperature) and significant neutron damage. High-Cr martensitic HT9 steel is an excellent candidate for SFR cladding and duct material due to its compatibility with liquid sodium, good thermal conductivity, resistance to void swelling, and strong creep rupture strength [1-4].However, the harsh in-core environment of SFRs can cause complex microstructural changes and mechanical property degradation in HT-9. Ensuring the safe use of HT9 cladding for metallic fuel requires both a thorough understanding of its mechanical response to microstructure evolution as well as reliable microstructure-sensitive modeling predictions. Microstructure-sensitive modeling of high temperature creep behavior in HT9 cladding for SFR applications currently lack experimental data to model the phenomena accurately. To fill this need, methods to perform microstructural characterization have been developed and performed on HT9.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Diffusion behavior of lanthanide fission products in bcc Fe cladding: A first-principles study

Fuel-cladding chemical interaction poses significant challenges in nuclear reactors, where fission products generated from nuclear fuel interact with Fe-based cladding materials, potentially compromising their structural integrity. This study investigates the diffusion behavior of lanthanide fission products, Lanthanum (La), Cerium (Ce), Praseodymium (Pr), and Neodymium (Nd), within body-centered cubic (bcc) Fe cladding using the density functional theory, nudged elastic band method, and self-consistent mean field theory. Our results reveal significant vacancy binding energies, particularly with the 1st and 2nd nearest neighbors, which diminish beyond the 5th nearest neighbor, with La exhibiting the strongest binding affinity, followed by Nd, Ce, and Pr. The nudged elastic band calculations indicate significant high barriers for the dissociation of 1st nearest neighbor vacancy-solute pairs for all fission products. The tracer diffusion coefficients of these fission products were derived in an Arrhenius form, with a magnetic correction that accounts for the high-temperature paramagnetic state. The significant trapping effect of vacancies caused by a very dilute concentration of fission products reduces vacancy mobility, potentially leading to modifications in point defect supersaturation, void nucleation, and swelling under irradiation. These represent critical challenges for irradiated cladding materials. The tracer diffusion coefficients indicate that Nd diffuses the fastest, followed by La, Ce, and Pr. Furthermore, this study provides essential insights for understanding fission product transport in cladding materials and informs future design strategies to mitigate fuel-cladding chemical interaction, ultimately enhancing nuclear reactor safety and performance.

Diffusion↗
DOE OSTI2022

A Review of Irradiation Damage and Effects in α-Uranium

Understanding irradiation damage and effects in α-uranium (α-U) is critical to modeling the behavior of U-based metallic fuels. The aim of this review is to address the renewed interest in U-based metallic fuels by examining the state-of-the-art knowledge associated with the effect of irradiation on the microstructure, dimensional changes, and properties of α-U. We critically review the research progress on irradiation-induced growth and swelling, the enhancement of plastic flow and superplasticity by irradiation, and the effect of irradiation on thermal and electrical properties of α-U. Finally, we outline the research directions that require advancements, specifically the need to carry out fundamental research on several of the less understood mechanisms of irradiation damage and effects in α-U.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Assessing the Long-Term Stability of Anion Exchange Membranes for Electrochemical CO 2 Reduction

Materials and cell components used in CO 2 electrolysis have largely been adapted from technologies initially developed for water electrolysis and fuel cells. However, electrochemical CO 2 reduction introduces distinct material challenges due to the unique chemical environment in this process. Here, in this study, we conducted ex-situ 1000 h stability tests on commonly used anion exchange membranes, exposing them exclusively to electrolytes and organic molecules used or produced during CO 2 electrolysis, at concentrations relevant to and compatible with postseparation processes. Notably, 15% w/w n-propanol and 5 M acetic acid caused complete dissolution or partial disintegration of the membranes unless cross-linking was present and remained stable throughout the test. When the membranes stayed physically intact, most of them exhibited excellent chemical stability in alkaline medium containing alcohols or formic acid, which was confirmed by vibrational spectroscopy and ion exchange capacity measurements. However, exposure to alcohol-and acid-containing solutions led to a substantial increase in swelling and water uptake, with potential implications for mechanical stability, ion/product crossover, and compression management of adjacent components. The potential effects of CO 2 electroreduction products on membrane stability, their subsequent impact on electrolyzer performance, and mitigation strategies are discussed.

CO2RR↗
DOE OSTI2024

Selective ion transport through hydrated micropores in polymer membranes

Abstract Ion-conducting polymer membranes are essential in many separation processes and electrochemical devices, including electrodialysis 1 , redox flow batteries 2 , fuel cells 3 and electrolysers 4,5 . Controlling ion transport and selectivity in these membranes largely hinges on the manipulation of pore size. Although membrane pore structures can be designed in the dry state 6 , they are redefined upon hydration owing to swelling in electrolyte solutions. Strategies to control pore hydration and a deeper understanding of pore structure evolution are vital for accurate pore size tuning. Here we report polymer membranes containing pendant groups of varying hydrophobicity, strategically positioned near charged groups to regulate their hydration capacity and pore swelling. Modulation of the hydrated micropore size (less than two nanometres) enables direct control over water and ion transport across broad length scales, as quantified by spectroscopic and computational methods. Ion selectivity improves in hydration-restrained pores created by more hydrophobic pendant groups. These highly interconnected ion transport channels, with tuned pore gate sizes, show higher ionic conductivity and orders-of-magnitude lower permeation rates of redox-active species compared with conventional membranes, enabling stable cycling of energy-dense aqueous organic redox flow batteries. This pore size tailoring approach provides a promising avenue to membranes with precisely controlled ionic and molecular transport functions.

Science & Technology - Other Topics↗
DOE OSTI2021

Thermal properties of U-Mo alloys irradiated under high fission power density

A variety of physical and thermal property measurements made on irradiated U-Mo alloy monolithic fuel samples with a Zr diffusion barrier and clad in Al alloy 6061 are reported. These properties form the basis for additional investigations in thermal behavior of U-Mo fuel under high performance research reactor irradiation conditions. Measurements were performed on samples harvested from fuel plates irradiated under high fission power density and surface heat flux and complement previous measurements on samples subjected to moderate fission power density and surface heat flux. Specific heat capacity of irradiated monolithic U-Mo increases with increasing temperature and fission density, but carries large uncertainties associated with thickness measurements used to determine the mass fraction of the layer constituents for extraction of the U-Mo specific heat capacity, specifically the very thin and nonuniform Zr diffusion barrier. Density of irradiated monolithic U-Mo decreases with increasing fission density resulting from fission gas swelling and porosity formation. Thermal diffusivity of irradiated monolithic U-Mo increased with increasing temperature and decreased with increasing fission density. Thermal conductivity of irradiated monolithic U-Mo increased with increasing temperature, and in general, appeared to decrease and become less sensitive to temperature with increasing fission density. Thermal conductivity measurements compared to a semi-empirical model agreed within ±30%. It is suspected that the main driver in deviation between model calculations and measurements is the fission gas swelling determination, which does not account for fission power density or irradiation temperature.

uranium (U), molybdenum, nuclear fuel, thermal con↗
DOE OSTI2021

Pretreatment of Biomass by Selected Type-III Deep Eutectic Solvents and Evaluation of the Pretreatment Effects on Hydrothermal Carbonization

Hydrothermal carbonization (HTC) is a novel thermochemical conversion that converts wet biomass into energy dense solid fuel. Residual moisture under subcritical conditions reacts with a lignin-cellulose-hemicellulose matrix with the major reactions being identified as dehydration and decarboxylation. Among other reaction parameters (e.g., temperature, time, pressure), biomass morphology often plays a key role in HTC. The hypothesis of this study was enhancing the porous structure of biomass without significantly affecting biopolymer composition would augment hydrothermal carbonization (HTC). To prove the hypothesis, two type-III deep eutectic solvents (DESs), namely choline chloride:urea (ChCl:Urea, 1:2 mol/mol) and methyltriphenylphosphonium bromide:ethylene glycol (MTPB:EG, 1:4 mol/mol), were studied to pretreat loblolly pine at room temperature and ambient pressure for 1 h. DES pretreatment shows swelling of the biomass, increasing the surface fiber-to-fiber gap length by 52% and 185% for ChCl:Urea and MPTB:EG pretreatments, respectively. The total pore volume remained intact (2.6 × 10 –3 cm 3 /g), although new small pores evolved, and existing pores were abated with DES pretreatment. Hydrochars prepared from DES pretreated loblolly pine showed a high O/C and H/C ratio resulting in a significant increase of energy content (up to 42%) and a decrease of mass yield (up to 50 wt %), indicating an enhancement of HTC severity due to the alteration of surface morphology by DES. Finally, a preliminary process economics revealed that integrated DES pretreatment-HTC would increase fixed capital investment but decrease the cost of operation and manufacturing than the standalone HTC process.

09 BIOMASS FUELS↗
DOE OSTI2026

Design Trade-Offs in Composite Fuel Cell Membranes: Effects of Reinforcement and Chemical Additives

Perfluorosulfonic acid (PFSA) membranes are critical components in proton exchange membrane fuel cells, where performance depends on balancing ionic conductivity, mechanical durability, and chemical stability. This study characterizes a composite membrane (NC700) featuring PFSA-impregnated expanded polytetrafluoroethylene (ePTFE) reinforcement and cerium-based radical scavengers, benchmarked against unreinforced NR211. Complementary techniques, including electron microscopy, X-ray scattering, infrared spectroscopy, thermogravimetric analysis, and dynamic mechanical analysis, identify the structural and compositional strategies employed in NC700. Water sorption isotherms reveal lower water uptake for NC700 across all conditions, attributed to reinforcement and cerium incorporation. Reinforcement reduces in-plane swelling from 11% to 2.1% at 90% RH, confirming strong swelling anisotropy, while maintaining mechanical properties at elevated temperatures. While the ionic conductivity of NC700 is approximately 10% lower than that of NR211, the reduced thickness yields a 40% decrease in calculated area-specific resistance, suggesting the composite architecture can favorably shift the conductivity-stability trade-off. The composite structure also reduces gas permeability, indicating potential for improved separator function alongside favorable transport properties. Systematic deconvolution of reinforcement and additive contributions shows that conductivity losses from cerium incorporation are largely offset by gains from the lower equivalent-weight polymer, providing quantitative relationships that may guide composite membrane design for fuel cells and other electrochemical applications.

25 ENERGY STORAGE↗
DOE OSTI2026

ROADRUNNER uranium nitride MiniFuel: Experimental design, fabrication and pre-irradiation baseline characterization for accelerated burnup testing

Uranium nitride (UN) is a promising fuel candidate for advanced reactor systems owing to its high uranium density and thermal conductivity; however, its qualification remains constrained by the scarcity of well-controlled irradiation performance data. Here, to address this limitation, the ROADRUNNER (Research On ADvancing the peRformance of UraNium Nitrides in Extreme enviRonments) campaign employs the MiniFuel platform in the High Flux Isotope Reactor (HFIR) to enable accelerated burnup irradiation testing under tightly controlled and largely isothermal conditions. This paper presents the experimental design, fuel fabrication, and pre-irradiation baseline characterization of the ROADRUNNER UN MiniFuel campaign. Thirty-six UN minidisc specimens were fabricated with systematically varied as-fabricated density (86–96% of theoretical density), carbon impurity content (961–5240 ppm), oxygen content (≤ ∼2000 ppm), and grain size (2.5–24 μm). The irradiation matrix spans nominal fuel temperatures of 873 K, 1173 K, and 1473 K and target burnups of 3.75%, 6.0%, and 7.5% fissions per initial metal atom (FIMA). Neutronic and thermal analyses were performed to define specimen-specific burnup accumulation and temperature histories, establishing the boundary conditions for subsequent in-pile behavior. Comprehensive pre-irradiation characterization—including dimensional metrology, density verification, impurity analysis, X-ray diffraction, Raman spectroscopy, scanning electron microscopy, X-ray computed tomography, and confocal profilometry—provides a detailed baseline for post-irradiation examination. Pre-irradiation data were further used to generate predictive estimates of fission gas release and swelling using existing empirical correlations. This quantitative comparison reveals substantial inter-model divergence at intermediate and elevated temperatures that exceeds propagated input uncertainties, highlighting structural gaps in the historical irradiation database. The ROADRUNNER irradiation campaign is currently underway in HFIR, with initial firs cycle completed in late 2025 and remaining targets scheduled through 2027. The experimental design and baseline dataset presented here establish the framework needed to interpret forthcoming post-irradiation measurements and to provide discriminating data for the validation and refinement of physics-based UN fuel performance models.

Lopes, Denise Adorno [Oak Ridge National Laborator↗
NASA NTRS1995

Stress-Simulating Witness Panels

Special panel fixtures developed for verifying integrity of bonds between propellants and insulators in solid-fuel rocket motors by applying, to specimens of propellant and insulator material, stresses similar to those caused by shrinkage during fabrication of motors. Assemblies of fixtures and specimens called "stress-simulating witness panels." Concept also applicable to stress testing of bonds in other manufactured products subject to shrinkage or to swelling.

Graham, Robert P.↗
DOE OSTI2022

Overview of Base Model in Parametric Studies Specific to Performance of U-Mo Plates

This paper provides an overview of the base model specifically developed to perform parametric sensitivity studies on the U-10Mo monolithic fuel system. U-Mo monolithic fuels are being considered for the conversion of test reactors into high-performance research reactors that operate using proliferation-resistant, low-enriched uranium (LEU) fuels. These plate-type fuels contain a high-density, low-enrichment fuel sandwiched between zirconium diffusion barriers and encapsulated in aluminum claddings. All U.S. high-performance research reactors have released the designs of their LEU monolithic fuel reactor cores. These designs include nearly 50 distinct fuel plate geometries with different operational parameters. Consequently, a single generic plate geometry representing all the extreme points in this design matrix is unrealistic. To evaluate the performance for various parameters, a set of sensitivity studies was performed. These studies considered various input parameters (i.e., geometric, operational, and material property-related). The results revealed valuable information about plate performance and the sensitivity of this performance to various modeling inputs. To establish a reference state for comparing these result, base model featuring representative irradiation conditions was developed. To capture in-reactor behavior accurately, incorporation of representative constitutive models capable of evolving properties with respect to temperature, irradiation time, and burnup was needed. The behavioral models considered burnup-dependent properties, swelling, creep, and degradation. This paper introduces the base model created for the parametric sensitivity studies. The detailed description of the procedure includes the model geometry, model discretization, thermo-mechanical coupling, material properties and behavioral models. This paper also provides selected results and assesses the performance of the base model.

42 ENGINEERING↗
DOE OSTI2020

Evaluation of the effects of neutron irradiation on first-generation corrosion mitigation coatings on SiC for accident-tolerant fuel cladding

In this work, high purity SiC and SiC/SiC composites coated with commercial TiN, Cr, CrN, or CrN/Cr multilayer coatings were irradiated in Ar or flowing PWR water in the Massachusetts Institute of Technology Nuclear Reactor Laboratory (MITR). Irradiation in Ar was performed in the core. In the water environment, identical samples were placed in one of three different locations: in-core, providing exposure to neutron damage and radiolysis-affected water; above-core, where samples were exposed to radiolysis-affected water but not neutron damage, or outside of the core, where samples were exposed to the coolant water without the effects of radiation. Radiation in Ar revealed significant cracking of all but the TiN coatings, attributed to differential swelling between the coating and substrate. Lattice swelling was not observed in any of the coatings, but 0.2% void swelling was observed in the Cr coating. All of the coatings failed during water exposures in the core. Likewise, CrN/Cr spalled in each condition. Cr was protective, except under radiation damage as a result of cracking, and TiN severely degraded in the core with no coating was found following exposure. A SiC/coating ATF cladding system is anticipated to perform adequately following improvements in coating ductility and purity.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Electrospun Hybrid Perfluorosulfonic Acid/Sulfonated Silica Composite Membranes

Electrospinning was employed to fabricate composite membranes containing perfluorosulfonic acid (PFSA) ionomer, poly(vinylidene fluoride) (PVDF) reinforcement and a sulfonated silica network, where the latter was incorporated either in the PFSA matrix or in the PVDF fibers. The best membrane, in terms of proton conductivity, was made by incorporating the sulfonated silica network in PFSA fibers (Type-A) while the lowest conductivity membrane was obtained when sulfonated silica was incorporated into the reinforcing PVDF fibers (Type-B). A Type-A membrane containing 65 wt.% PFSA with an embedded sulfonated silica network (at 15 wt.%) and with 20 wt.% PVDF reinforcing fibers proved superior to the pristine PFSA membrane in terms of both the proton conductivity in the 30–90% RH at 80 °C (a 25–35% increase) and lateral swelling (a 68% reduction). In addition, it was demonstrated that a Type-A membrane was superior to that of a neat 660 EW perfluoroimide acid (PFIA, from 3M Co.) films with respect to swelling and mechanical strength, while having a similar proton conductivity vs. relative humidity profile. This study demonstrates that an electrospun nanofiber composite membrane with a sulfonated silica network added to moderately low EW PFSA fibers is a viable alternative to an ultra-low EW fluorinated ionomer PEM, in terms of properties relevant to fuel cell applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Radiation response of FeCrAl-coated Zircaloy-4

Coating the surface of Zircaloy-4 light water reactor fuel cladding tube is of considerable interest for enhancing its accident tolerance. In this study, thermal annealing of FeCrAl-coated Zircaloy-4 at 725 °C for 500 h, was used to induce interfacial reactions between Zircaloy-4 and FeCrAl. The interface zones were then irradiated by 3.5 MeV Zr ions at 400 °C, up to 50, 100, 150 peak dpa values. Transmission electron microscopy (TEM) and scanning TEM were used to characterize microstructural and composition changes before and after ion irradiation. Three interfacial phases were identified: FeZr 3 , (Fe,Cr) 2 Zr, and ZrC. The widest intermetallic layer, FeZr3, had large grains. The narrower phases, (Fe,Cr)2Zr and ZrC, contained small grains and were often mixed. The unexpected observation of the ZrC phase was attributed to the presence of very small impurity level concentrations of carbon in the powder material. No void swelling was observed in any of the phases, including the FeCrAl coating and Zircaloy-4 substrate. (Fe,Cr) 2 Zr, however, fully amorphized after irradiation, even at the lowest dpa.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Damage Modeling of Solid Oxide Fuel Cells Accounting for Redox Effects

This work applies a multiscale mechanistic damage model developed for brittle ceramics and implemented in commercial finite element (FE) packages via user subroutines to study progressive damage in solid oxide fuel cells (SOFC) subjected to thermomechanical loading under normal operating and shutdown conditions including redox effects. The damage model captures the micromechanics of stiffness reduction due to material porosity change and microcracking and integrates the as-obtained stiffness reduction law into a continuum damage mechanics (CDM) formulation for the evolution of microcracks up to fracture. The volumetric “swelling” that occurs during redox is treated in constitutive modeling similarly to thermal expansion, but swelling strains are irreversible. Furthermore, this damage model was first validated through predictions of strength and stress-strain response for the SOFC electrode materials. Next, it has been applied to predict the potential for degradation in a generic planar SOFC stack with large active area cells. Multicell stack models were simulated in both co-flow and counter-flow configurations. In addition, a constant temperature redox cycle was also simulated to capture overall cell electrode damage due to volumetric swelling of the nickel (Ni)-based anode in the anode-supported cells.

25 ENERGY STORAGE↗
DOE OSTI2024

Nanostructured Alumina Forming Austenitic Alloy (NAFA) Production Using Mechanical Alloying and High-Temperature Consolidation

Alumina-forming austenitic (AFA) alloys are a promising class of nuclear materials because of their high-temperature oxidation/corrosion resistance and mechanical properties. Unfortunately, these alloys are limited in use for core material applications, and they are specifically limited for use as nuclear fuel cladding because of their high Ni-transmutation and helium generation rate in-service. Improving these alloys through a fine dispersion of oxide precipitates and thus increasing the effective irradiation sink strength of the alloy system may mitigate many of the degradation phenomena expected during alloy deployment. These phenomena include high-temperature helium embrittlement and cavity swelling for lead-cooled fast reactor applications. This work effort uses combination of conventional and advanced manufacturing approaches are being used to fabricate nanostructured AFA (NAFA) materials. As the first objective of this initiative, a conventional AFA was modified using mechanical alloying and extrusion to alter the precipitation characteristics to include a fine dispersion of nanoscale oxides intended to serve as traps for irradiation-induced point defects and transmuted He within the lattice. This analysis compared the efficacy of the conventional mechanical alloying and extrusion approach with the unalloyed AFA consolidated approach using hot isostatic pressing (HIP). It was found that, although the mechanical alloying approach is successful in producing a fine distribution of oxides within the first nanostructured AFA (NAFA-1), the distribution is heterogeneous because of the mild milling parameters used to prevent cold welding of powder to the spherical milling media. The additional dispersion of oxides, coupled with a higher volume fraction of other secondary phases in the NAFA-1, produces higher alloy strengths that range up to 600°C in comparison to the unalloyed HIP AFA, thus exceeding the operating temperature of lead-cooled fast reactors. However, the strength of the NAFA-1 is lower than that of the HIP AFA at 800°C, which is presumed to be a function of increased secondary phases from the nonoptimized AFA chemistry. Future work is planned on a newly procured NAFA-2 chemistry that is more suitable for advanced reactor applications exploring new manufacturing routes.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Hermeticity of SiC/SiC composite and monolithic SiC tubes irradiated under radial high-heat flux

Demonstration of hermetic SiC fiber–reinforced SiC matrix composite cladding under normal operating environments has been identified as one of the most critical feasibility issues for accident-tolerant fuel cladding in light-water reactors. This study provides critical experimental data needed for understanding the effects of irradiation on hermeticity. SiC composite and monolithic tubes were neutron-irradiated to 2 displacements per atom with and without a nominal radial heat flux of 0.6 MW/m2 to produce a simulated in-pile stress state for the normal operation of a light-water reactor. The through-thickness temperature gradient under irradiation results in a gradient in swelling, which causes a significant stress buildup. Such irradiation-induced stress was modeled using a commercial finite element analysis code. The radial heat flux–irradiation synergism was experimentally investigated by constructing a special irradiation capsule and evaluating the helium hermeticity of the specimens. The simulated stress state exhibited a near equi-biaxial tensile axial and hoop stress of ~150 MPa at the inner surface of the SiC composite tube. This stress level is potentially beyond the matrix cracking stress. Degradation of hermeticity of the SiC composite tubes was observed after irradiation, indicating irradiation-induced cracking, whereas the irradiated monolithic SiC tubes remained hermetic. In conclusion, the results indicate that loss of hermeticity caused by radiation-induced microcracking is a potential issue for SiC composite cladding, depending on the magnitude of the temperature gradients. Coating the outer surface of the cladding was identified as a mitigation strategy that might overcome the cracking issue.

36 MATERIALS SCIENCE↗