Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “failure diameter”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Damage tolerance research on composite compression panels

The damage tolerance of composites was investigated. Results show that severe degradation in material strength may occur due to impact damage and that reduced strain allowables should be considered to compensate for possible impact damage. The mechanisms of failure involved in impact so that local damage will be reduced and arrest of propagating fracture initiated at impact locations are examined. Compression strength reductions for damage due to impact by a 1.27 cm diameter spherical projectile in thick laminates representative of wing skin panels are presented. Also discussed are the results of concepts recently evaluated to improve damage tolerance. These concepts range from improvements at the materials level to advanced structural configurations designed to arrest or limit the growth of propagating fractures. The results indicate that substantial improvements in the damage tolerance of graphite-epoxy composite structures can be achieved through the proper combination of materials and structural design.

Rhodes, M. D.↗
NASA NTRS1985

Effects of load proportioning on the capacity of multiple-hole composite joints

This study addresses the issue of adjusting the proportion of load transmitted by each hole in a multiple-hole joint so that the joint capacity is a maximum. Specifically two-hole-in-series joints are examined. The results indicate that when each hole reacts 50% of the total load, the joint capacity is not a maximum. One hole generally is understressed at joint failure. The algorithm developed to determine the load proportion at each hole which results in maximum capacity is discussed. The algorithm includes two-dimensional finite-element stress analysis and failure criteria. The algorithm is used to study the effects of joint width, hole spacing, and hole to joint-end distance on load proportioning and capacity. To study hole size effects, two hole diameters are considered. Three laminates are considered: a quasi-isotropic laminate; a cross-ply laminate; and a 45 degree angle-ply laminate. By proportioning the load, capacity can be increased generally from 5 to 10%. In some cases a greater increase is possible.

Hyer, M. W.↗
DOE OSTI2018

Measurement of Average Burnup in TRISO-Coated Particles from AGR-2 UCO Compacts 2-2-2 and 6-4-2

Burnup analysis was performed on tristructural-isotropic (TRISO)-coated particles deconsolidated from compacts irradiated by the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program in the second irradiation experiment (AGR-2) [Collin 2014]. The AGR-2 irradiation experiment included TRISO fuel particles with kernels containing both uranium oxide and uranium carbide, called UCO, where uranium carbide is included with the commonly-used uranium oxide in the kernel to provide a getter for oxygen liberated during fission and limit CO production. This allows the UCO-TRISO particles to be taken to higher burnup without failure from excessive internal CO pressure or CO-corrosion of the SiC layer. The UCO kernels were fabricated and coated at BWX Technologies Nuclear Operations Group (BWXT-NOG) with a 150-mm-diameter engineering-scale coater. The UCO-TRISO batch used in the AGR-2 irradiation experiment was Batch 93073, which had kernels with an average diameter of 426.7 μm and average coating thicknesses moving out from the kernel of 98.9 μm (buffer), 40.4 μm (IPyC), 35.2 μm (SiC), 43.4 μm (OPyC) [Barnes and Marshall 2009]. The TRISO particle were shipped to ORNL to be formed into compacts for irradiation testing. The compact lot qualified for the AGR-2 irradiation test was lot LEU09-OP2-Z and had an average of 3176 UCO-TRISO particles in each compact [Hunn, Montgomery, and Pappano 2010]. Compilations of the properties data for the particles and compacts are available in a pre-irradiation characterization summary report for the AGR-2 fuel composites [Hunn, Savage, and Silva 2010].

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
NASA NTRS1976

Contamination control in hybrid microelectronic modules

Thin and thick film test specimens were utilized to study the effects of silicone and epoxy hybrid microcircuit coatings on 0.025 mm diameter aluminum and gold ultrasonic bonds, and 0.051 diameter gold pulsed-thermocompression bonds. Chip-to-substrate and substrate-to-substrate geometries were included. Because sealed packages were utilized, a test pattern design was incorporated that allowed the determination of bond failures by making resistance measurements external to the package after the various environmental tests. All wire bonds were non-destructively pull tested prior to sealing. Tests included the PIN test, temperature cycling, and high temperature storage.

Himmel, R. P.↗
NASA NTRS1988

Properties of silicon carbide fiber-reinforced silicon nitride matrix composites

The mechanical properties of NASA Lewis developed SiC/RBSN composites and their thermal and environmental stability havd been studied. The composites consist of nearly 30 vol pct of aligned 142 micron diameter chemically vapor-deposited SiC fibers in a relatively porous silicon nitride matrix. In the as-fabricated condition, the unidirectional and 2-D composites exhibited metal-like stress-strain behavior, graceful failure, and showed improved properties when compared with unreinforced matrix of comparable density. Furthermore, the measured room temperature tensile properties were relativley independent of tested volume and were unaffected by artifical notches normal to the loading direction or by thermal shocking from temperatures up to 800 C. The four-point bend strength data measured as a function of temperature to 1400 C in air showed that as-fabricated strength was maintained to 1200 C. At 1400 C, however, nearly 15 pct loss in strength was observed. Measurement of room temperature tensile strength after 100 hr exposure at temperatures to 1400 C in a nitrogen environment indicated no loss from the as-fabricated composite strength. On the other hand, after 100 hr exposure in flowing oxygen at 1200 and 1400 C, the composites showed approximately 40 pct loss from their as-fabricated ultimate tensile strength. Those exposed between 400 to 1200 C showed nearly 60 pct strength loss. Oxidation of the fiber/matrix interface as well as internal oxidation of the porous Si3N4 matrix are likely mechanisms for strength degradation. The excellent strength reproducibility, notch insensitivity, and high temperature strength of the composite makes it an ideal candidate for advanced heat engine applications provided coating or densification methods are developed to avoid internal oxidation attack.

Bhatt, Ramakrishna T.↗
NASA NTRS1993

Large floor-fractured craters and isostatic crater modification: Implications for lithospheric thickness on Venus

Several of the largest craters on Venus, including Mead, Meitner and Isabella, exhibit well-developed floor fracture patterns combining a central set of radial features with a peripheral set of concentric fractures. This pattern strongly resembles the fracture patterns observed in the largest floor-fractured craters on the Moon (e.g. Humboldt, Gauss, Petavius). Although most lunar floor-fractured craters apparently reflect crater modification by igneous intrusions and volcanism, we propose that the fractures in these larger craters represent domical flexure events in response to post-impact isostatic uplift. Since the extent of uplift and surface failure in this model depends on both the size of the basin cavity and the local lithospheric thickness, this interpretation also provides a means for constraining lithospheric thicknesses on Venus. Based on the apparent onset diameter of isostatic crater modification, we derive lithospheric thickness estimates for the Moon of approximately 80 - 100 km, and for Venus of approximately 50 - 70 km.

Wichman, R. W.↗
NASA NTRS1995

Correlations of Different Surface Tests: Tire Behavior Math Model for the High Speed Civil Transport (HSCT) and Michelin Tire Properties Tests for Boeing 777

In the surfaces correlation study, several different volumetric and drainage measurement techniques for classifying surface texture were evaluated as part of a major study to develop and improve methods for predicting tire friction performance on all types of pavement. The objective of the evaluation was to seek relationships between the different techniques, and to relate those results to surface frictional characteristics. We needed to know how each of the tests could be related to each other. Another of my assigned projects was to make a tire behavior math model for the High Speed Civil Transport (HSCT) using the same methods used for the space shuttle a few years ago. A provided third order equation with two variables was used. This model will also be used for studies with the Boeing 777. Only a few changes will be necessary to adapt it for this other aircraft, which is the newest offered by Boeing. In my final project I was involved with testing the tires for this new aircraft using the Aircraft Landing Dynamics Facility (ALDF) test carriage within the carriage house at LaRC. A 50 inch diameter radial tire manufactured by Michelin Aircraft Tire Corporation had to be tested to double overload of 114,000 pounds. The rated load of each tire is 57,000 pounds, but Boeing required tests assuming failure of a companion tire that could have cost Michelin approximately $12 million to build a facility to provide the required test capability. Here at LaRC, only minimum modifications to the facility were required to perform this specific test.

Roman, Ivan↗
NASA NTRS2002

Observations of Planet Crossing Asteroids

The goals of this research were the physical and dynamical characterization of planet crossing asteroids (Earth crossers, Mars crossers, Centaurs, and Pluto crossers, meaning trans-Neptunian objects), including colorimetry, rotational studies, and astrometry. Highlights are listed as follows: 1) Produced one doctoral dissertation (R. J. Whiteley, A Compositional and Dynamical Survey of the Near-Earth Asteroids). A key result is the fraction of Q-type asteroids among the near-Earth population was found to be about one-third; 2) Had prediscovery image showing the binary nature of trans-Neptunian object 1998 WW31, which is the first TNO to have a satellite found in orbit around it; 3) Discovery of shortest known rotation period for any asteroid (2000 D08, rotation period 78 seconds); it is just one of several fast-rotating small asteroids observed during the course of this project; 4) Discovery of a Centaur asteroid (1998 QM107) with, at the time, the smallest known orbital eccentricity among the Centaurs (0.13) and nearly in a 1:1 resonance with Uranus (semimajor axis of 19.9 AU); 5) Discovery of Apollo-type asteroid 1999 OW3, with a surprisingly bright absolute magnitude of 14.6 (estimated diameter of 4.6 km), brightest Apollo found in that calendar year; 6) Discovery of Aten-type asteroid 2000 SG344, which has the highest cumulative Earth impact probability among the near-Earth asteroids and a very Earth-similar orbit; 7) Instrumental in repairing the orbit of a numbered near-Earth asteroid for which prediscovery observations had been mis-attributed to it (2000 VN2); 8) Second-opposition recovery of 30-meter diameter Apollo-type asteroid 1998 KY26 in early 2002 when it was at a favorable magnitude of 24.8; 9) Primary contributor of astrometric observations of the CONTOUR fragments to the CONTOUR project following the failure of the spacecraft s kick motor; and 10) Development of orbit and ephemeris computation code that handles short observational arcs, observations at small solar elongations where indeterminacy is a known problem, and a small number of observations (including just two). Starting in 2000 November, the Spaceguard Central Node began prioritizing near-Earth asteroids in need of astrometric observation. Our own follow-up efforts relied on these listings, with emphasis given to the faintest objects where the combination of a 2.2-m telescope and a site with subarcsecond seeing produces a limiting magnitude close to 25, which represents a unique and valuable capability. The attached table, last updated in August, demonstrates the arc-lengthening capabilities of a faint limiting magnitude. Tabulated are the arc lengths before and after our observation(s), whether our observation is the last one available for the object in question, and the approximate magnitude of the object at the time of the observation.

Tholen, David J.↗
NASA NTRS1997

Particle Characterization in Rocket Exhaust Plumes

A method to characterize particles in rocket exhaust plumes is developed. The particle velocity, size, and material composition are determined from crater characteristics resulting from impacts into aluminum and copper targets passed through the plume. The targets are mounted on a steel arm approximately 21 inches (53 cm) long which is rotated through the plume at sufficient velocity to prevent material failure resulting from thermal effects. A Scanning Electron Microscope (SEM) with secondary x-ray detectors is used to determine the particle material, and a standard optical measurement microscope is used to determine the crater diameter and depth. The crater diameter and depth are used in turn, as inputs to a ballistics computer code to estimate the velocity and size of the particle. The target has a safe residence time in the plume of approximately 50 ms before reaching an unacceptably high temperature. The = must mach a velocity of 104 ft/s (32 m/s) before entering the plume to produce the design residence time of 20 ms. The arm is actuated by a torsion spring with a 5-inch (13 cm) outer diameter, 0.625-inch (16 mm wire diameter, and 11 coils. A prototype of the entire rocket exhaust particle impact characterization system (PICS) was constructed and statically tested.

Callen, E. Eugene, Jr.↗
DOE OSTI2021

AGR-5/6/7 Irradiation As Run Predictions Using PARFUME

The PARticle FUel ModEl (PARFUME), a fuel performance modeling code used for high-temperature gas-cooled reactors, was used to model the Advanced Gas Reactor (AGR)-5/6/7 irradiation test using as-run physics and thermal data. The AGR-5/6/7 irradiation test consists of the combined fifth, sixth, and seventh planned irradiations of the AGR Fuel Development and Qualification Program. The AGR-5/6/7 test train is a multi-capsule, instrumented experiment that is designed for irradiation in the 133.4-mm diameter northeast flux trap position of the Advanced Test Reactor (ATR) at Idaho National Laboratory. Each capsule contains compacts filled with uranium oxycarbide unaltered fuel particles. This report documents the calculations performed to predict the failure probability of tristructural isotropic (TRISO)-coated fuel particles during the AGR-5/6/7 experiment. In addition, this report documents the calculated fission product release fraction from the fuel. The calculations include modeling of the AGR 5/6/7 irradiation that occurred from February 2018 to July 2020 over nine ATR cycles, including six normal cycles and three power axial locator mechanism cycles, for a total of approximately 376 effective full power days (EFPD). The irradiation conditions and material properties of the AGR-5/6/7 test predicted zero fuel particle failures in Capsules 1, 3, and 4. Fuel particle failures were predicted in two of the compacts in Capsule 2 and one particle failure is predicted in each one of the compacts in Capsule 5. All compacts that exhibited fuel particle failures predicted by PARFUME were caused by localized stress concentrations in the silicon carbide (SiC) layer caused by cracking in the inner pyrolytic (IPyC) layer. In addition, shrinkage of the buffer and IPyC layer during irradiation resulted in formation of a buffer-IPyC gap. Compacts with a lower irradiation temperature and fluence experienced the smallest buffer-IPyC gap formation. Conversely, higher irradiated temperature compacts with a high fluence experienced the largest buffer-IPyC gap formation. Compact 3-6-3 experienced the largest buffer IPyC gap formation of just under 21.7 µm. The release fraction of fission products silver (Ag), cesium (Cs), and strontium (Sr) vary depending on capsule location and irradiation temperature. The maximum release fraction of Ag occurs in Capsule 3, reaching up to 59.5% for the TRISO fuel particles (compact 3-6-3). The release fraction of the other two fission products, Cs and Sr, are much smaller. A maximum Cs release fraction of 1.1% occurred in compact 3-4-3 and 4.4% for Sr in compact 3-6-3.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2012

Development of a Low-Cost Rotary Steerable Drilling System

The project had the goal to develop and commercialize a low-cost rotary steerable system (LCRSS) capable of operating downhole at conventional pressures and temperatures to reduce operating costs by a minimum of 50% and lost-in-hole charges by at least 50% over the currently offered systems. The LCRSS system developed under this project does reduce operating costs by 55% and lost-in-hole charges by at least 50%. The developed product is not commercializable in its current form. The overall objective was to develop and commercialize a low cost rotary steerable system (LCRSS) capable of operating downhole at conventional pressures and temperatures (20,000 psi/150 C) while reducing the operating costs by 50% and the lost-in-hole charges by 50% over the currently available systems. The proposed reduction in costs were to be realized through the significant reduction in tool complexity, a corresponding increase in tool reliability as expressed in the mean-time between failure (MTBF), and a reduction in the time and costs required to service tools after each field operation. Ultimately, the LCRSS system was to be capable of drilling 7 7/8 in. to 9 5/8 in. borehole diameters. The project was divided into three Phases, of which Phases I & II were previously completed and reported on, and are part of the case file. Therefore, the previously reported information is not repeated herein. Phase III included the fabrication of two field ready prototypes that were to be subjected to a series of drilling tests at GTI Catoosa, DOE RMOTC, and at customer partnering wells, if possible, as appropriate in the timing of the field test objectives to fully exercise all elements of the LCRSS. These tests were conducted in an iterative process based on a performance/reliability improvement cycle with the goal of demonstrating the system met all aspects required for commercial viability. These tests were conducted to achieve continuous runs of 100+ hours with well trajectories that fully exercised the tool's build/turn/drop/hold target capabilities and its higher end ratings for bit weight, torque and rotary speed. The tool teardowns were rigorously analyzed at the conclusion of each field run to assess component wear rates and to fully document any detrimental behavior(s) observed.

15 GEOTHERMAL ENERGY↗
NASA NTRS2000

Effects of Heat Treatment on the Ballistic Impact Properties of Inconel 718 for Jet Engine Fan Containment Applications

The effects of heat treating Inconel 718 on the ballistic impact response and failure mechanisms were studied. Two different annealing conditions and an aged condition were considered. Large differences in the static properties were found between the annealed and the aged material, with the annealed condition having lower strength and hardness and greater elongation than the aged. Correspondingly large differences were found in the velocity required to penetrate material in the two conditions in impact tests involving 12.5 mm diameter, 25.4 mm long cylindrical Ti-6-4 projectiles impacting flat plates at velocities in the range of 150 to 300 m/sec. The annealed material was able to absorb over 25 percent more energy than the aged. This is contrary to results observed for ballistic impact response for higher velocity impacts typically encountered in military applications where it has been shown that there exists a correlation between target hardness and ballistic impact strength. Metallographic examination of impacted plates showed strong indication of failure due to adiabatic shear. In both materials localized bands of large shear deformation were apparent, and microhardness measurements indicated an increase in hardness in these bands compared to the surrounding material. These bands were more localized in the aged material than in the annealed material. In addition the annealed material underwent significantly greater overall deformation before failure. The results indicate that high elongation and better strain hardening capabilities reduce the tendency for shear to localize and result in an unstable adiabatic shear failure. This supports empirical containment design methods that relate containment thickness to the static toughness.

Pereira, J. Michael↗
DOE OSTI2021

Adoption of image-driven machine learning for microstructure characterization and materials design: A Perspective

Microstructure characterization enables the development of structure-processing-property relationships critical to several research areas within the broad field of materials science, from alloy design to the assessment of corrosion resistance, and failure analysis. Conventional approaches to material characterization have relied on either qualitative inference by the human ex-pert or software applications that can extract high-level features from images, such as boundary segmentation, average grain diameter, etc. Such approaches rely heavily on subject matter expert user intervention and knowledge of what phases or more generally, what microstructural features, are of interest. The recent surge in the adoption of machine learning techniques to address problems in materials engineering has brought with it an increased interest and application of Image Driven Machine Learning (IDML) approaches. In this work, we review the applications of IDML to the field of materials characterization. A canonical hierarchy of stages is defined, which when put sequentially together completes an IDML study: problem definition, dataset building, model selection and training, model evaluation, and integration with existing instrumentation or simulation workflow. The studies reviewed in this work are analyzed from the perspective of each of these stages. Such a review permits agranular assessment of the field, for example the impact of IDML on materials characterization at the nanoscale, the size of a typical dataset required to train a semantic segmentation model on electron microscopy images, ubiquitousness of transfer learning in the domain, etc. Finally, we discuss the importance of interpretability and explainability in the field of IDML for materials characterization, and provide an overview of two emerging techniques in the field: semantic segmentation and generative adversarial networks.

Baskaran, Arun↗
NASA NTRS2018

Cumulative Distribution of Ballistic Impact Failures of Common Twisted-Pair Data Cables at Orbital Speeds

Data wire cable runs are a significant presence on the exterior of the International Space Station (ISS), and continued ISS mission support requires detailed assessment of cables due to micrometeoroid and orbit debris (MMOD) impact. These data wire cables are twisted-pair cables consisting of two 22AWG stranded conductors and fillers inside a tight fitting braided copper shield. The copper shield and its contents are covered with a jacket that has a nominal outer diameter of 3.76 mm and beta-cloth tape. The ISS engineering community has identified two loss-of-function mechanisms for these cables: open circuits due to severed conductors within the cable, and short circuits due to contact between conductors or grounded components. As these data cables are low power systems, short circuits are not expected to burn away the contact, so both open and short circuits are considered permanent loss-of-function for the cable. A total of ninety-seven impact experiments have been performed into these cables to develop a statistical model for the failure of these cables to be used in reliability studies. The experimental work has yielded cumulative distribution functions for these cables for steel and aluminum components of the orbital debris environment at representative speeds and impact obliquities.

Miller, Joshua E.↗
DOE OSTI2023

Chemo-mechanical-microstructural coupling in the tarsus exoskeleton of the scorpion Scorpio palmatus

The multiscale structure of biomaterials enables their exceptional mechanical robustness, yet the impact of each constituent at their relevant length scale remains elusive. Here, we used SAXD analysis to expose the intact chitin-fiber architecture within the exoskeleton on a scorpion's claw, revealing varying orientations, including Bouligand and unidirectional regions different from other arthropod species. We uncovered the contribution of individual components’ constituent behavior to its mechanical properties from the micro- to the nanoscale. At the microscale, in-situ micromechanical experiments were used to determine site-specific stiffness, strength, and failure of the biocomposite due to fiber orientation, while metal-crosslinking of proteins is characterized via fluorescence maps. At the constituent level, combined with FEA simulations, we uncovered the behavior of fiber-matrix deformation with fiber diameter <53.7 nm and protein modulus in the range 1.4–11 MPa. The unveiled microstructure-mechanics relationship sheds light on the evolved structural functionalities and constituents' interactions within the scorpion cuticle.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS1979

Optimum design of spacecraft radiators for large capacity or long duration mission applications

Results of trade studies comparing optimum pumped fluid and hybrid heat pipe/pumped fluid radiator designs are presented. Design variables considered in the system optimization analyses include transport fluid properties and Reynolds number, pump loop component reliabilities, micrometeoroid protection, heat pipe spacing, manifolding and flow routing in pumped fluid designs, transport tubing spacing and diameters, and radiator fin parameters. Criteria for evaluating candidate radiator system designs include mass, radiator area, and overall system reliability. The studies show advantages in constructing large systems from small independent subsystems with oversizing to account for subsystem failures. The optimum size and survivability of the subsystems are identified as a function of the radiator construction, the system heat rejection requirements, the mission duration, and the system reliability requirements.

Leach, J. W.↗
NASA NTRS2002

Major Effects of Nonmetallic Inclusions on the Fatigue Life of Disk Superalloy Demonstrated

The fatigue properties of modern powder metallurgy disk alloys can vary because of the different steps of materials and component processing and machining. Among these variables, the effects of nonmetallic inclusions introduced during the powder atomization and handling processes have been shown to significantly degrade low-cycle fatigue life. The levels of inclusion contamination have, therefore, been reduced to less than 1 part per million in state-of-the-art nickel disk powder-processing facilities. Yet the large quantities of compressor and turbine disks weighing from 100 to over 1000 lb have enough total volume and surface area for these rare inclusions to still be present and limit fatigue life. The objective of this study was to investigate the effects on fatigue life of these inclusions, as part of the Crack Resistant Disk Materials task within the Ultra Safe Propulsion Project. Inclusions were carefully introduced at elevated levels in a nickel-base disk superalloy, U720, produced using powder metallurgy processing. Multiple strain-controlled fatigue tests were then performed on extracted test specimens at 650 C. Analyses were performed to compare the low-cycle fatigue lives and failure initiation sites as functions of inclusion content and fatigue conditions. Powder of the nickel-base superalloy U720 was atomized in argon at Special Metals Corporation, Inc., using production-scale high-cleanliness powder-processing facilities and handling practices. The powder was then passed through a 270-mesh screen. One portion of this powder was set aside for subsequent consolidation without introduced inclusions. Two other portions of this powder were seeded with alumina inclusions. Small, polycrystalline soft (Type 2) inclusions of about 50 mm diameter were carefully prepared and blended into one powder lot, and larger hard (Type 1) inclusions of about 150 mm mean diameter were introduced into the other seeded portion of powder. All three portions of powder were then sealed in separate containers, hot isostatically pressurized, extruded, forged into subscale disks, and heat treated. Low-cycle-fatigue specimens were then extracted, machined, and tested. Fatigue tests were performed at 650 C in closed-loop servohydraulic testing machines using induction heating and axial extensometers. All tests were continued to failure, and fractographic evaluations were performed on all specimens to determine the crack initiation sites. A large majority of the failures in specimens with introduced inclusions occurred at cracks initiating from inclusions at the specimen surface, as shown for each type of inclusion in the following bar chart. The inclusions significantly reduced fatigue life from unseeded material levels, as shown in the bar chart. These effects were found to depend on the strain range, strain ratio, and inclusion size. Tests at lower strain ranges and higher strain ratios resulted in larger effects of inclusions on life. Inclusion effects on life were thereby maximized in tests at the lowest strain range of 0.6 percent and the most positive strain ratio of 0.5. Under these conditions, small Type 2 inclusions reduced life substantially-- about 20 times, whereas large Type 1 inclusions dramatically reduced life 100 times. These results clearly demonstrate that it is essential to include the effects of inclusions for realistic predictions of disk fatigue life. Important issues, including temperature dependence, crack initiation versus propagation, surface treatments, realistic disk features and machining, and realistic disk spin testing will be addressed to accurately model inclusion effects on disk fatigue life. Fatigue life varied from well over 105 cycles for no inclusions to a little over 103 cycles for 100-micrometer inclusions. A single crack initiating at a surface-connected seeded inclusion caused failure in each case.

Gabb, Timothy P.↗
NASA NTRS1999

Effects of Heat Treatment on the Ballistic Impact Properties of Inconel 718 for Jet Engine Fan Containment Applications

The effects of heat treating Inconel 718 on the ballistic impact response and failure mechanisms were studied. Two different annealing conditions and an aged condition were considered. Large differences in the static properties were found between the annealed and the aged material, with the annealed condition having lower strength and hardness and greater elongation than the aged. High strain rate tests show similar results. Correspondingly large differences were found in the velocity required to penetrate material in the two conditions in impact tests involving 12.5 mm diameter, 25.4 mm long cylindrical Ti-6-4 projectiles impacting flat plates at velocities in the range of 150 to 300 m/sec. The annealed material was able to absorb over 25 percent more energy than the aged. This is contrary to results observed for ballistic impact response for higher velocity impacts typically encountered in military applications where it has been shown that there exists a correlation between target hardness and ballistic impact strength. Metallographic examination of impacted plates showed strong indication of failure due to adiabatic shear. In both materials localized bands of large shear deformation were apparent, and microhardness measurements indicated an increase in hardness in these bands compared to the surrounding material. These bands were more localized in the aged material than in the annealed material. In addition the annealed material underwent significantly greater overall deformation before failure. The results indicate that lower elongation and reduced strain hardening behavior lead to a transition from shear to adiabatic shear failure, while high elongation and better strain hardening capabilities reduce the tendency for shear to localize and result in an unstable adiabatic shear failure. This supports empirical containment design methods that relate containment thickness to the static toughness.

Pereira, J. Michael↗