Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “elevated temperature and pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

Promoted Metals Combustion at Ambient and Elevated Temperatures

Promoted combustion testing of materials, Test 17 of NASA STD-6001, has been used to assess metal propensity to burn in oxygen rich environments. An igniter is used at the bottom end of a rod to promote ignition, and if combustion is sustained, the burning progresses from the bottom to the top of the rod. The physical mechanisms are very similar to the upward flammability test, Test 1 of NASA STD-6001. The differences are in the normal environmental range of pressures, oxygen content, and sample geometry. Upward flammability testing of organic materials can exhibit a significant transitional region between no burning to complete quasi-state burning. In this transitional region, the burn process exhibits a probabilistic nature. This transitional region has been identified for metals using the promoted combustion testing method at ambient initial temperatures. The work given here is focused on examining the transitional region and the quasi-steady burning region both at conventional ambient testing conditions and at elevated temperatures. A new heated promoted combustion facility and equipment at Marshall Space Flight Center have just been completed to provide the basic data regarding the metals operating temperature limits in contact with oxygen rich atmospheres at high pressures. Initial data have been obtained for Stainless Steel 304L, Stainless Steel 321, Haynes 214, and Inconel 718 at elevated temperatures in 100-percent oxygen atmospheres. These data along with an extended data set at ambient initial temperature test conditions are examined. The pressure boundaries of acceptable, non-burning usage is found to be lowered at elevated temperature.

Engel, Carl D.↗
NASA NTRS1979

High-temperature microphone system

Pressure fluctuations in air or other gases in an area of elevated temperature are measured using a condenser microphone located in the area of elevated temperature and electronics for processing changes in the microphone capacitance located outside the area the area and connected to the microphone by means of high-temperature cable assembly. The microphone includes apparatus for decreasing the undesirable change in microphone sensitivity at high temperatures. The high temperature cable assembly operates as a half-wavelength transmission line in an AM carrier system and maintains a large temperature gradient between the two ends of the cable assembly. The processing electronics utilizes a voltage controlled oscillator for automatic tuning thereby increasing the sensitivity of the measuring apparatus.

Zuckerwar, A. J.↗
NASA NTRS1973

Rates and mechanisms of the atomic oxygen reaction with nickel at elevated temperatures

The oxidation of nickel by atomic oxygen at pressure from 1 to 45 N/sq m between 1050 and 1250 K was investigated. In these ranges, the oxidation was found to follow the parobolic rate law, viz., K sub p = 0.0000114 exp(-13410/T) g squared/cm4/sec for films of greater than 1 micron thickness and was pressure independent. The activation enthalpy for the oxidation reaction was 112 + or - 11 kj/mole (27 + or - 3 kcal/mole). Of a number of possible mechanisms and defect structures considered, it was shown that the most likely was a saturated surface defect model for atomic oxidation, based on reaction activation enthalpies, impurity effects, pressure independence, and magnitudes of rates. A model judged somewhat less likely was one having doubly ionized cationic defects rate controlling in both atomic and molecular oxygen. From comparisons of the appropriate processes, the following enthalpy values were derived: enthalpy of activation (Ni diffusion in Ni0) = 110 + or - 30 kj/mole and standard enthalpy change for reaction formation (doubly ionized cation vacancies in Ni0 from atomic oxygen)= -9 + or - 25 kj/mole.

Christian, J. D.↗
DOE OSTI2025

Groundwater table elevation and temperature from 2015 to 2024 across Meander C at the Lower Montane site in the East River Watershed, Colorado.

This groundwater level elevation and temperature data package is aimed at improving the predictive understanding of hydro-biogeochemical processes at the lower montane site in the East River Watershed, Colorado. The dataset is obtained using pressure transducers placed in shallow wells in the floodplain. This dataset contains data from wells ER-CPA1 to ER-CPA6. Another dataset contains the data from wells at nearby Locations. Each file contains the water level elevation and the water temperature. Water level elevation has been obtained using the barometric pressure from the pressure transducer (Hobos sensor) in the well, barometric pressure from a sensor in air located at the same site (lower montane), depth from top-of-casing (TOC) to sensor measurement point, and TOC elevation. Data have been checked with a few measurements of water table depths. A real-time kinematic (RTK) global positioning system (GPS) has been used to survey the TOC (data in file Well_Location.csv). The water level elevation is given in UTM13N Geoid2012AB. While depth to water level is not present in the data files, it can be easily calculated with the TOC and distance to ground provided in the GPS coordinate file. The dataset quality is discussed in Collection/Analysis section of the methods. Time-series of measurements were initially added to the archive for the period 2015 to 2019, and later updated with time-series until 2024 (end of data collection). The dataset contains 7 *.csv data files, and 3 *.csv metadata files. Feel free to contact the author with any questions or collaboration interests. The publication year was updated from "2020" to "2025" to reflect the revised version of this dataset.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Development of a Framework and Methodology for an Advanced Reactor Materials Environmental Effects Design Guide

Advanced non-light-water reactor components may operate at elevated temperature while experiencing cyclic loading, significant neutron irradiation, and exposure to reactor coolant. ASME Boiler and Pressure Vessel Code, Section III, Division 5, provides design rules for elevated-temperature service but does not include specific procedures to account for environmental effects on material properties. This report develops an initial framework and methodology for an Environmental Effects Design Guide (EEDG) focused on neutron irradiation; coolant-environment effects are reserved for future work. The proposed approach treats irradiation as a property-based overlay on the existing Division 5 design process, with two routes: a sparse-data route applying two reduction factors — FCR on creep-rupture strength and FF on fatigue life — for the creep-fatigue evaluations that typically control the design of advanced high-temperature reactor components, and a fuller framework developing the property-to-rule chain across the four Division 5 checks (primary load, strain limits and ratcheting, creep-fatigue, and buckling), together with swelling and weldments as scope items. Both routes are scoped by an in-pile qualification that restricts the use of post-irradiation-examination-derived properties in regimes where an in-pile mechanism could control the design outcome. Illustrative outputs derived on a compiled annealed Type 316 database — FCR ≈ 0.78–0.86 and FF ≈ 0.4 — demonstrate the calculation method within that specific dataset. The framework is an initial, testable design-rule concept; it identifies a practical path for preliminary design evaluations under sparse data and the material data and testing needed to develop the framework further.

Barua, Bipul (ORCID:0000000247184113)↗
NASA NTRS1999

Diagnostic Clast-Texture Criteria for Recognition of Impact Deposits

It is difficult to find definitive evidence for impact in the geological record because there are many endogenous geological processes that can produce diamictites similar to those generated by impact ejecta. The classic impact criteria of shock fabrics in certain minerals, and iridium layers, for example, may be either difficult to find, or long-since erased from the impact site (shock fabrics also anneal with time). It is important to be able to recognize impact-generated materials in order to understand earth's crustal development and biological evolution. In future exploration of Mars and other solar-system bodies, recognition of impact materials will be important for elucidating planetary evolution, planetary volatile inventories, and exobiological issues. The cobble depicted is typical of many that have been found in diamictite deposits in Belize generated by the Chicxulub K-T impact event. The pebbles are roughly-hewn in general shape with smoothed corners and edges. Surfaces are almost uniformly frosted (on both protuberances and hollows), but some asperities are glazed. Optical microscopy and thin-section petrographic microscopy reveal the frosting to be only a few microns thick, with a well-defined granular structure; grains are the same size as those composing the bulk of the limestone, but their clearer appearance may represent annealing. One or two adjacent pebble faces are often decorated with striated gouges and closely-spaced hemispherical depressions representing indentation hollows produced by well-rounded impacting clasts of up to 0.5 cm in diameter. Some of the impactors are still embedded in the cobble surface. Non-destructive x-ray diffraction techniques showed the impactors to be of the same mineralogy as the target cobble. We believe this unusual glazing and frosting to be related to the impact event, but this must be reconciled with its survival for over 60 my. since it is composed of one of the most alterable substances, CaCO3. We focus, however, on the non-fractured rounded pebbles that appear to have impacted the larger cobble as a swarm of clasts, probably encountered during ballistic flight. It cannot be defined whether the cobble swept through the pebble cloud, or the pebbles rained upon a slowermoving cobble. Two interesting questions arise: (1) Where did large numbers of such well rounded pebbles come from in the ejecta curtain?, and (2) How did they embed themselves in a nominally brittle rock without suffering damage? Are the well-rounded pebbles crystalline (devitrified) melt spherules? Further investigations are in progress. If the cobble was cold and brittle, impact of well-rounded pebbles would have produced Hertzian fracture patterns (a) in the virtually elastically isotropic cobble target. For penetration depths of about 0.5 of the impactor diameter, the pebbles would require a relative impact velocity sufficient to cause pebble fragmentation and crushing, and the development of a complex Hertzian-Boussinesq fracture field (b) involving deep fracturing and lateral surface spalling (impact velocities > 50 m/s). The existing relationship could only evolve by the impact of cold, hard pebbles into a soft, plastic cobble surface (c). For limestone to have been plastic, it must have been at elevated temperature, but to prevent calcification of the material, the ambient pressure must also have been elevated. This would be possible either in the impact's gas plume, or within the confines of a thin aerodynamically-produced shock bow generated by supersonic ballistic motion of the cobble. In the latter case, it is implied that the cobble swept through the pebbles rather than vice-versa. Although there are high T-P conditions associated with volcanism, such textures have not been reported on volcaniclastic materials, nor from other high T-P environments; e.g., metamorphic (as far as the authors are aware). We propose that this very easily recognizable embedding and indentation surface texture can be used as a diagnostic criterion for the recognition of impact ejecta. The term "peening texture" is suggested, because it is absolutely analogous to the plastic-deformation induced, metal-surface textures generated by ball-bearing bombardment used in engineering metallurgy to work-harden metal surfaces. Additional information is contained in the original (Figures).

Marshall, J. R.↗
NASA NTRS2004

Thermostructural Analysis of Carbon Cloth Phenolics "Ply Lifting" and Correlation to LHMEL Test Results

This paper provides a discussion of the history of Carbon Cloth Phenolic (CCP) ply lifting in the Redesigned Solid Rocket Motor (RSRM) Program, a brief presentation of theoretical methods used for analytical evaluation, and results of parametric analyses of CCP material subject to test conditions of the Laser Hardened Material Evaluation Laboratory. CCP ply lift can occur in regions of the RSRM nozzle where ply angle to flame surface is generally less than about 20 degrees. There is a heat rate dependence on likelihood and severity of the condition with the higher heating rates generally producing more ply lift. The event occurs in-depth, near the heated surface, where the load necessary to mechanically separate the CCP plies is produced by the initial stages of pyrolysis gas generation due to the thermal decomposition of the phenolic resin matrix. Due to the shallow lay-up angle of the composite, normal components of the indepth mechanical load, due to "pore pressure", are imparted primarily as a cross-ply tensile force on the interlaminar ply boundaries. Tensile capability in the cross-ply (out of plane) direction is solely determined by the matrix material capability. The elevated temperature matrix material capabilities are overcome by pressure induced mechanical normal stress and ply-lift occurs. A theoretical model used for CCP in-depth temperature, pressure, and normal stress prediction, based on first principles, is briefly discussed followed by a parametric evaluation of response variables subject to boundary conditions typical of on-going test programs at the LHMEL facility. Model response demonstrates general trends observed in test and provides insight into the interactivity of material properties and constitutive relationships.

Clayton, Louie↗
NASA NTRS2003

Mechanical Testing of PMCs under Simulated Rapid Heat-Up Propulsion Environments: In-Plane Compressive Behavior - II

Carbon fiber thermoset polymer matrix composites (PMC) with high temperature polyimide based in-situ polymerized monomer reactant (PMR) resin has been used for some time in applications which can see temperatures up to 550 F. Currently, graphite fiber PMR based composites are used in several aircraft engine components including the outer bypass duct for the GE F-404, exit flaps for the P&W F-100-229, and the core cowl for the GE/Snecma CF6-80A3. Newer formulations, including PMR-II-50 are being investigated as potential weight reduction replacements of various metallic components in next generation high performance propulsion rocket engines that can see temperatures which exceed 550 F. Extensive FEM thermal modeling indicates that these components are exposed to rapid heat-up rates (up to -200 F/sec) and to a maximum temperature of around 600 F. Even though the predicted maximum part temperatures were within the capability of PW-II-50, the rapid heat-up causes significant through-thickness thermal gradients in the composite part and even more unstable states when combined with moisture. Designing composite parts for such extreme service environments will require accurate measurement of intrinsic and transient mechanical properties and the hygrothermal performance of these materials under more realistic use conditions. The mechanical properties of polymers degrade when exposed to elevated temperatures even in the absence of gaseous oxygen. Accurate mechanical characterization of the material is necessary in order to reduce system weight while providing sufficient factors of safety. Historically, the testing of PMCs at elevated temperatures has been plagued by the antagonism between two factors. First, moisture has been shown to profoundly affect the mechanical response of these materials at temperatures above their glass transition temperature while concurrently lowering the material's Tg. Moisture phenomena is due to one or a combination of three effects, i.e., plastization of polymeric material by water, the internal pressure generated by the volatilization of water at elevated temperatures, and hydrolytic chemical decomposition. However, moisture is lost from the material at increasing rates as temperature increases. Second, because PMCs are good thermal insulators, when they are externally heated at even mild rates large thermal gradients can develop within the material. At temperatures where a material property changes rapidly with temperature the presence of a large thermal gradient is unacceptable for intrinsic property characterization purposes. Therefore, long hold times are required to establish isothermal conditions. However, in the service environments high-heating-rates, high temperatures, high-loading rates are simultaneous present along with residual moisture. In order to capture the effects of moisture on the material, holding at- temperature until isothermal conditions are reached is unacceptable particularly in materials with small physical dimensions. Thus, the effects due to moisture on the composite's mechanical characteristics, ie., their so-called analog response, may be instructive. One approach employed in this program was rapid heat-up (approx. 200 F/sec.) and loading of both dry and wet in-plane compressive specimens to examine the effects of moisture on this resin dominated mechanical property of the material.

Stokes, Eric H.↗
NASA NTRS1978

Arc-jet test and analysis of Orbiter TPS inter-tile heating in high pressure gradient flow

During entry of the Space Shuttle Orbiter, the convective heating within inter-tile gaps of the Thermal Protection System (TPS) material produces elevated tile sidewall temperatures in regions of high surface pressure gradient. Arc-jet tests have been conducted recently to obtain a measure of the gap heating down the TPS tile sidewalls at test conditions representative of Orbiter flight environments. The object of this paper is to present the gap heating correlations that were developed from a thermal analysis for 3-D curved and flat TPS tile segments. Predictions of gap sidewall temperature were obtained within 30 F of test data on both Wing Glove and Double Wedge models. Derived heating ratios were obtained for a range of test conditions (pressure, pressure gradient, enthalpy, boundary layer thickness, gap width, surface temperature, etc.). The results of the study, which showed that heating ratios varied with the pressure gradient times the square root of the surface pressure, are being used to provide an assessment of gap filler requirements on Orbiter forward fuselage/chine and wing glove regions.

Rochelle, W. C.↗
NASA NTRS1977

Structure of the atmosphere of Mars in summer at mid-latitudes

Instruments onboard Viking 1 and 2 landers were used to measure the structure of Mars' atmosphere in situ from near the surface to an altitude of 120 km. Atmospheric structure was found to be well defined by the instruments and relatively similar at the two sites. Viking 1 and 2 surface pressures were 7.62 and 7.81 mbar, and temperatures were 238 K and 236 K, respectively, with pressures at the elevation of the reference ellipsoid of 6.74 and 6.30 mbar. Mean temperature was found to decrease with a lapse rate of about 1.6 K/km (significantly subadiabatic) from above the boundary layer to about 40 km. The temperature was then near isothermal with a large-amplitude wave superimposed (attributed to the diurnal thermal tide). It is suggested that the mean profile is governed by radiative equilibrium. The obtained density data are found to merge well with those obtained by an upper-atmosphere spectrometer (at 200 km). The temperature wave is found to continue above 100 km while increasing in wavelength and amplitude.

Seiff, A.↗
DOE OSTI2025

Groundwater table elevation and temperature from 2015 to 2024 at the Lower Montane site in the East River Watershed, Colorado.

This groundwater level elevation and temperature data package is aimed at improving the predictive understanding of hydro-biogeochemical processes at the lower montane site in the East River Watershed, Colorado. The dataset is obtained using pressure transducers placed in shallow wells in the floodplain. This dataset contains data from wells with Location ID's ER-DOW (alias DO1West), ER-DOE (alias DO2East), ER-MBA1 (alias M1Bend1), ER-MBA2 (alias M1Bend2), ER-UPW (alias UP1West), ER-UPM (alias UP2), ER-UPE (alias UP3East). Another dataset contains the data from wells with Location ID's ER-CPA1 to ER-CPA6. Each file contains the water level elevation and the water temperature. Water level elevation has been obtained using the barometric pressure from the pressure transducer (Hobos sensor) in the well, barometric pressure from a sensor in air located at the same site (lower montane), depth from top-of-casing (TOC) to sensor measurement point, and TOC elevation. Data have been checked with a few measurements of water table depths. A real-time kinematic (RTK) global positioning system (GPS) has been used to survey the TOC (data in file Well_Location.csv). The water level elevation is given in UTM13N Geoid2012AB. While depth to water level is not present in the data files, it can be easily calculated with the TOC and distance to ground provided in the GPS coordinate file. The dataset quality is discussed in Collection/Analysis section of the methods. Time-series of measurements were initially added to the archive for the period 2015 to 2019, and later updated with time-series until 2024 (end of data collection). The dataset contains 8 *.csv data files, and 3 *.csv metadata files. Feel free to contact the author with any questions or collaboration interests. The publication year was updated from "2020" to "2025" to reflect the revised version of this dataset.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

CALPHAD modeling of uranium nitride (UN) fabrication routes enabled by first-principles calculations

The thermochemical details of fabricating uranium nitride (UN) by ammonolysis of uranium tetraflouride (UF 4 ) were determined using density functional theory (DFT) and CALculation of PHAse Diagrams (CALPHAD) computational methods. The thermochemical data of all binary, ternary, and quaternary U-H-N-F phases were computed using DFT, and the data for the phases that have not been measured experimentally, including UN 2 and NH 4 F(g), were combined with existing experimentally-determined data for CALPHAD modeling. The DFT data were benchmarked using experimental Gibbs energy of reaction and experimental thermochemical data for individual species. Phase diagrams relevant to the ammonolysis reaction are depicted, showing regions of stability for solid U-N, U-F and U-N-F phases. An unidentified phase produced in a previous experiment was identified as UN 0.95 F 1.2 (UNF) by comparing its X-ray diffraction spectrum to the experimental spectrum, and its formation during the fabrication of UN from UF 4 is supported by the simulated phase diagram. Here, it is calculated that UN 2 can be produced by the ammonolysis of UF 4 , but requires elevated temperatures, high NH 3 (g) partial pressure, and large amounts of flowing NH 3 (g) to avoid solid flu oride impurities in the uranium nitride. Likewise, U 2 N 3 can be produced instead at temperatures greater than 980 K. The use of silane (SiH 4 ) gas was investigated as a potential additive in the ammonolysis fabrication route to speed removal of fluorine. The addition of SiH 4 (g) offers little advantage to the removal of fluorine, and adds the complication of Si 3 N 4 formation. The use of DFT to fill in missing data to perform CALPHAD calculations demonstrated here allows for the determination of more comprehensive and trustworthy phase diagrams than the use of existing experimental data alone.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2020

Adsorption of furan, hexanoic acid, and alkanes in a hierarchical zeolite at reaction conditions: Insights from molecular simulations

Hierarchical zeolites containing both micropores and mesopores are valuable catalysts for facilitating reactions of large molecules. Furan acylation by fatty acids is a promising reaction for valorizing biomass, and the self-pillared pentasil (SPP) zeolite was found to perform particularly well for this reaction. To better understand the distribution of molecules in hierarchical zeolites at the elevated temperature (T = 523 K) and the elevated pressure (p >1 bar) associated with typical reaction conditions, unary and binary adsorption were predicted using Monte Carlo simulations in the isothermal–isobaric Gibbs ensemble. Adsorption of six species (furan, hexanoic acid, -hexane, -decane, -tetradecane, and 3,6-diethyloctane) was investigated from vapor, liquid, and supercritical phases, and loadings into the micropores, onto the mesopore surface, and in the mesopore interior of SPP were obtained. As pressure increases, -alkanes fill the micropores before loading the surface and then the interior of the mesopore, while furan and hexanoic acid adsorb strongly to the mesopore surface due to hydrogen bonding interactions with surface silanols. Hydrogen bonding interactions also draw hexanoic acid molecules in the micropore region toward the pore mouths, so their carboxylic acid group forms H-bonds with silanols, while the alkyl tails interact with the micropore walls. Mesopore condensation is observed for molecules below their critical point, and occurs when the Gibbs free energy of transfer into the mesopore interior and onto the mesopore surface converge. When hexanoic acid adsorption occurs in the presence of alkane solvents, then the selectivity and spatial distribution of hexanoic acid in the micropores and on the surface can be tuned by adjusting the fluid pressure and the alkane length and/or branching.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Exceptional strength and wear resistance in an AA7075/TiB 2 composite fabricated via friction consolidation

The friction consolidation method successfully reinforced aluminum 7075 alloy (AA7075) with high-volume fractions (12 and 24 vol%) of titanium diboride (TiB 2 ) by high pressure and severe plastic deformation at elevated temperatures. The consolidated AMCs have a uniform dispersion of submicron- and micron-sized TiB 2 particles in the AA7075 matrix, with significant refinement of the matrix grain size and the particles. The addition of TiB 2 significantly increases hardness by up to 50 %, Young’s modulus by up to 62 %, and ultimate tensile strength by up to 28 % to 672 MPa, while reducing ductility by 80 %. Wear resistance of 7075/24 vol% TiB 2 improves seven-fold compared to baseline, making it comparable to that of carburized steels. Microstructure-based finite element modeling provided a theoretical strength limit of ~730 MPa for the composites and indicated that high triaxiality in conjunction with severe equivalent plastic strain in a narrow area between the TiB 2 particles led to early fracture initiations, limiting the ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Net Electronic Charge as an Effective Electronic Descriptor for Oxygen Release and Transport Properties of SrFeO 3 -based Oxygen Sorbents

Perovskite oxides, as oxygen sorbents, exhibit excellent potential in thermochemical redox applications such as chemical looping air separation (CLAS), resulting from their excellent redox properties and high tunability. The structural and compositional flexibility of perovskites, while making these mixed oxides highly versatile, also poses challenges for their design and optimization. Moreover, the elevated operating temperature and dynamic oxygen partial pressure swings during redox processes add additional complications for oxygen sorbent design. From a fundamental standpoint, finding simple yet effective descriptors for the effect of cation substitutions on oxygen sorbents’ redox and oxygen transport properties are of significant importance for rational optimization of perovskite-based oxygen sorbents. In the present study, a series of A/B-site-doped SrFeO 3-δ perovskites are investigated using density functional theory (DFT) + U simulations. From these simulations, an effective electronic structural descriptor, the net electronic charge (Δe) of oxygen anions, is extracted based on its excellent correlations with vacancy formation energy, experimentally derived oxygen capacity, and oxygen vacancy migration barrier. Overall, these findings provide an effective tool to correlate the oxygen sorbents’ redox performances with a simple yet physically meaningful descriptor for rational design and optimization of perovskites in the context of CLAS.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1984

Contamination Measurements During Ius Thermal Vacuum Tests in A Large Space Chamber

The levels of contamination that originate from inside the IUS equipment support section (ESS) due to outgassing from electronics components and wiring operating at elevated temperatures (80-160 F) were investigated. Pressure was measured inside and outside the ESS. Mass deposition measurements were made with quartz crystal microbalances (QCM) facing into and away from ESS vents. The OCM's were operated at -50 C and -180 C using thermoelectrically and cryogenically cooled QCM's. Gaseous nitrogen flow inside the ESS was used to obtain the effective molecular flow vent area of the ESS, which was evaluated to be 359 sq cm (56 sq in) compared to the 978 sq cm (150 sq in) estimated by an earlier atmosphere pressure billowing test. The total outgassing rate of the ESS materials at a temperature of 60 C (140 F) decays with a time constant of 11.5 hours based on pressure measurements during the hot cycle. A time constant of 22 hours was estimated for the fraction of the outgassing which will condense on a -50 C surface. In contrast, the time constant is only 10.1 hours for the outgassing material which condenses on a surface at -180 C. A surface at -180 C collects approximately one half of the material vented from the ESS which impinges on it. Pressure measurements show very good correlation with the mass deposition measurements.

C R Mullen↗
NASA NTRS1986

Stratified processes to analyze SSME parts and subsystems using Weibull methodology

Due to the various parts found in a Space Shuttle Main Engine (SSME), analyzation of every part is not feasible or needed. Based on previous mathematical modeling experience of high velocity cryogenic equipment, the environmental traits of location of the part, temperature range, fluid velocity, pressure range, and elevation variation of fluid flow as being significant factors were determined. Six parts categories were developed. The part categories are: (1) fuel turbomachinery, (2) oxidizer, (3) combustion devices, (4) valves, (5) ducts, and (6) lines. Due to a suspicion that superficial failure modes exist, six status codes were developed. The codes are: (1) part is in service presently, (2) part is out-of-service due to its own failure, (3) part is out-of-service due to engine (or some other part failure), (4) part is out-of-service because it's retired/obsolete (time related), (5) never fired-scrapped due to own problem or part is store, and (6) part is out-of-service for repair. It was suggested that to properly model failure behavior of SSME parts that: (1) significant factors contributing to failure must be examined, (2) relatively precision based on real life data must be examined, and (3) alternative definitions of failure must be initialized by the engineers.

Gray, Lou Allen Bell↗
NASA NTRS1990

The growth of zinc selenide single crystals by physical vapor transport in microgravity

Growth and characterization studies will be performed on zinc selenide single crystals. The high temperature outgassing behavior of the silica ampoule material will be studied in order to develop a cleaning and bake-out procedure that will minimize the amount of impurities introduced into the vapor from the ampoule materials and in particular during the seal-off procedure. The outgassing behavior of the ZnSe starting material will be studied during high vacuum refinement at elevated temperatures in order to develop a temperature pressure program that will optimize the removal of impurities while minimizing a shift in stoichiometry due to preferred evaporation of the higher fugacity component. The mass spectrometer system was completed, and after calibration, will be used to perform the above tasks. The system and its operation is described in detail.

Anderson, Elmer E.↗