Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electrode kinetics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Unraveling the Effects of Hierarchical Bimodal Microscale Porosity on Thick Electrodes

The thick electrode design is preferential in high-energy lithium-ion batteries (LIBs) systems. However, the sluggish ionic transport in homogeneous porous thick electrodes severely limits the areal capacity at high charging/discharging rates. The hierarchical porous design is a promising approach to mitigate kinetic limitations because it can distribute mass effectively in natural systems. In this study, the effects of bimodal microscale pores are fully investigated in thick electrodes from both architectural and electrochemical perspectives. Notably, by introduction of the bimodal microscale porous structure, the rate capability improves remarkably in thick electrodes with a low porosity (39%). Herein, by combining experimental results with simulations, this work presents a rational design guideline for preparing thick electrodes with a porosity at the commercial level, as well as simultaneous high energy and power densities, which brings new insights into the advanced electrode architecture design in scalable high-energy and high-power energy storage systems for practical applications.

25 ENERGY STORAGE↗
DOE OSTI2023

Morphology and Crystallinity Effects of Nanochanneled Niobium Oxide Electrodes for Na-Ion Batteries

Niobium pentoxide (Nb 2 O 5 ) is a promising negative electrode for sodium ion batteries (SIBs). By engineering the morphology and crystallinity of nanochanneled niobium oxides (NCNOs) the kinetic behavior and charge storage mechanism of Nb 2 O 5 electrodes were investigated. Amorphous and crystalline NCNO samples were made by modulating anodization conditions (20 - 40V and 140 - 180 °C) to synthesize nanostructures of differing pore sizes and wall thicknesses with identical chemical composition. The electrochemical energy storage properties of the NCNOs were studied with the amorphous samples showing better overall rate performance than the crystalline samples. The enhanced rate performance of the amorphous samples is attributed to the higher capacitive contributions and Na-ion diffusivity analyzed from cyclic voltammetry (CV) and galvanostatic intermittent titration technique (GITT). It was found that the amorphous samples with smaller wall thicknesses facilitated improved kinetics. Among samples with similar pore size and wall thickness, the difference in their power performance stems from crystallinity effect, which plays a more significant role in the resulting kinetics of the materials for Na-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2025

Alkaline Zinc Passivation Mechanism is Controlled by Hydroxide Concentration

We studied Zn passivation and oxide growth in Zincate (Zn(OH) 4 2− ) in 4 and 8 M KOH solutions using an electrochemical quartz crystal microbalance (EQCM), building on our initial work at 1 M KOH where passivation was kinetically controlled. A porous passivating oxide spontaneously forms on Zn electrodes when KOH is above 4 M and saturated with zincate. However, passivation does not occur when bulk zincate concentration is decreased, resulting in continual Zn dissolution. EQCM data suggests that the passivation mechanism is strongly affected by pOH. Mass transport and kinetic processes in the 4 M KOH electrolytes couple and govern Zn passivation. At 8 M, KOH concentration shifts passivation to mass transport control. We explain this by the increased solubility of Zn(OH) 3 − with increasing pOH. The variation in the mechanism of passivation implications for how passivation is handled in Zn-alkaline batteries. The importance of controlling the mass transport increases with increased pOH, suggesting that electrode design, additives, and potential flow should be optimized. At lower pOHs, kinetics and mass transport must be balanced to manage passivation effectively. Additionally, the changing nature of the native oxide layer on the surface has implications for the evenness of deposition and dissolution on the Zn electrode.

Wittman, Reed M. [Oak Ridge National Laboratory (O↗
DOE OSTI2021

Thickness-independent scalable high-performance Li-S batteries with high areal sulfur loading via electron-enriched carbon framework

Abstract Increasing the energy density of lithium-sulfur batteries necessitates the maximization of their areal capacity, calling for thick electrodes with high sulfur loading and content. However, traditional thick electrodes often lead to sluggish ion transfer kinetics as well as decreased electronic conductivity and mechanical stability, leading to their thickness-dependent electrochemical performance. Here, free-standing and low-tortuosity N, O co-doped wood-like carbon frameworks decorated with carbon nanotubes forest (WLC-CNTs) are synthesized and used as host for enabling scalable high-performance Li-sulfur batteries. EIS-symmetric cell examinations demonstrate that the ionic resistance and charge-transfer resistance per unit electro-active surface area of S@WLC-CNTs do not change with the variation of thickness, allowing the thickness-independent electrochemical performance of Li-S batteries. With a thickness of up to 1200 µm and sulfur loading of 52.4 mg cm −2 , the electrode displays a capacity of 692 mAh g −1 after 100 cycles at 0.1 C with a low E/S ratio of 6. Moreover, the WLC-CNTs framework can also be used as a host for lithium to suppress dendrite growth. With these specific lithiophilic and sulfiphilic features, Li-S full cells were assembled and exhibited long cycling stability.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Ultrahigh Areal Capacity Holey Graphene Air Cathodes for Li-O2 and Li-CO2 Batteries

Advanced lithium (Li) batteries using gaseous cathode reactants such as oxygen (O2) and carbon dioxide (CO2)are attractive energy storage platforms because the gases are obtained externally and thus not accounted for in the total battery weight when fully charged.The discharge products at the cathode, typically Li2O2 for Li-O2 batteries and Li2CO3 for Li-CO2 batteries, are insoluble in the electrolyte.Therefore, in order for such batteries to function properly, an “air cathode”,which is a conductive scaffold within the battery cell,is required as a physical location for cathode electrochemical reactions to occur. Prior research has identified many carbon nanomaterials such as carbon nanotubes and graphene as viable choices for air cathode scaffold, while various metallic and metal-free catalytic systems integrated onto carbon-based air cathodes have been developed to improve the sluggish discharge and charge reactions. For future practical applications, the air cathode must exhibit a usable capacity per unit electrode area, or areal capacity, a critical parameter that has been largely overlooked so far in this field. In order to achieve high areal capacity, the air cathode must exhibit a sufficient amount of accessible void volume per unit electrode area while maintaining the conductive scaffold integrity during the entire electrochemical process. Here we present an ultrathick,holey graphene-based air cathode platform fabricated from a facile dry compression process that exhibits remarkable areal capacity values. Holey graphene is a carbon nanomaterial derived from graphene, but with nanometer sized holes through the nanosheet thickness.The presence of these holes enhances mass transport through electrode thickness and also enables the unique dry-press fabrication process that is not achievable using other carbon scaffold materials.The dry-pressed holey graphene air cathode platform is not only compatible with catalyst incorporation to improve battery reaction kinetics, but also allows for novel engineering of electrode architectures that is not achievable using conventional electrode fabrication approaches.The applications of such highly versatile, ultrahigh areal capacity air cathode platforms to both Li-O2 and Li-CO2 battery chemistries will be discussed.

Li-O2 batteries, Li-CO2 batteries, holey graphene,↗
DOE OSTI2024

High protonic resistance of hydrocarbon-based cathodes in PEM fuel cells under low humidity conditions: Origin, implication, and mitigation

Hydrocarbon-based electrodes for proton-exchange membrane fuel cells face challenges in closing the performance gap with electrodes based on perfluorosulfonic acid ionomers, particularly under low humidity conditions. Alongside increased oxygen transport resistance and higher kinetic-induced overpotentials, the protonic resistance of these fluorine-free electrodes is the primary hurdle to improved performance. This study systematically investigates the origin and impact of the cathode protonic resistance on fuel cell performance, utilizing sulfonated phenylated polyphenylenes as hydrocarbon ionomers. Electrochemical characterization at low relative humidity (≤50 %) reveal a high protonic resistance arising from both lower conductivity of the hydrocarbon thin film compared to the bulk membrane and increased cathode tortuosity at a gas transport-optimized ionomer to carbon (I/C) ratio of 0.2. The poor protonic resistance at low relative humidities leads to a non-homogeneous current distribution across the thickness of the cathode electrode, resulting in lower catalyst utilization. To address this issue, reducing the thickness of the cathode CL while maintaining a constant Pt loading (i.e., increasing the Pt on carbon ratio) significantly reduces protonic resistance. This improvement compensates for the kinetic disadvantages of highly loaded carbon particles and results in a considerable performance increase by 40 % at 0.75 V under low relative humidities.

25 ENERGY STORAGE↗
DOE OSTI2026

Advancing the Performance of Anion Exchange Membrane Electrolysis by Employing a Powder-Based Ionomer during Anode Catalyst Layer Fabrication

The performance of anion exchange membrane water electrolysis (AEMWE) can be significantly improved by utilizing powdered ionomers during the fabrication of the anode catalyst layer (CL) to modify the CL properties. When comparing powdered ionomers to dispersed ionomers across various catalysts including cobalt oxide (Co 3 O 4 ), nickel−iron oxide (NiFe 2 O 4 ), and iridium oxide (IrO 2 ) the anode fabricated with powdered ionomers demonstrates improved performance in polarization curves, enhanced charge transfer kinetics, and reduced ohmic and transport losses, as evidenced by voltage breakdown and electrochemical impedance spectroscopy analyses. Optimal performance is achieved using a Co 3 O 4 catalyst with a 10 wt % powdered ionomer via the catalystcoated substrate method. Microscopy analyses reveal that electrodes formed with powdered ionomers during fabrication exhibit a more uniform catalyst and ionomer distribution, increased porosity with smaller pore areas, improved electronic conduction with less catalyst agglomeration isolated by a nonconductive ionomer, and enhanced interfacial contact with the membrane and transport layer. These findings highlight that ionomers in a powdered form can promote beneficial properties and are a promising approach to improving AEMWE efficiency.

08 HYDROGEN↗
DOE OSTI2022

Ultrafast Metal Electrodeposition Revealed by In Situ Optical Imaging and Theoretical Modeling towards Fast–Charging Zn Battery Chemistry

Metallic Zn is a preferred anode material for rechargeable aqueous batteries towards a smart grid and renewable energy storage. Importantly, understanding how the metal nucleates and grows at the aqueous Zn anode is a critical and challenging step to achieve full reversibility of Zn battery chemistry, especially under fast-charging conditions. Here, by combining in situ optical imaging and theoretical modeling, we uncover the critical parameters governing the electrodeposition stability of the metallic Zn electrode, that is, the competition among crystallographic thermodynamics, kinetics, and Zn 2+ -ion diffusion. Moreover, steady-state Zn metal plating/ stripping with Coulombic efficiency above 99 % is achieved at 10-100 mA cm -2 in a reasonably high concentration (3 M) ZnSO 4 electrolyte. Significantly, a long-term cycling-stable Zn metal electrode is realized with a depth of discharge of 66.7% under 50 mA cm -2 in both Zn || Zn symmetrical cells and MnO 2 || Zn full cells.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

The electrode–electrolyte interface of Cu via modulation excitation X-ray absorption spectroscopy

The development and application of modulation excitation X-ray absorption spectroscopy with sub-second resolution and better than 0.02% detection sensitivity unveils the kinetics of the anodic oxidation of Cu in bicarbonate electrolytes. Accessing the electrode–electrolyte interface under operating conditions and capturing time-resolved kinetics remain challenging in electrochemical studies. Copper's interfacial oxidation dynamics remain unclear despite extensive research. Modulation excitation X-ray absorption spectroscopy (ME-XAS) was used to probe Cu in 100 mM KHCO 3 with sub-second sensitivity, revealing that hydroxide forms 30 ± 10 ms before the appearance of Cu 2 O at positive potentials (0 to 0.5 V vs. RHE) near open-circuit conditions. From −0.4 to 0.8 V vs. RHE, hydroxide coverage reaches 49%, accompanied by a balanced presence of Cu( i ) and Cu( ii ) oxides. These insights into Cu interfacial redox behavior under intermittent renewable energy operation—relevant to CO 2 electrolyzer durability—enhance our fundamental understanding of electrochemical interfaces.

Garcia-Esparza, Angel T↗
DOE OSTI2021

Electrochemistry of the NaI-AlBr 3 Molten Salt System: A Redox-Active, Low-Temperature Molten Salt Electrolyte

NaI-AlBr 3 is a very appealing low melting temperature (<100 °C), salt system for use as an electrochemically-active electrolyte. This system was investigated for its electrochemical and physical properties with focus to energy storage considerations. A simple phase diagram was generated; at >100 °C, lower NaI concentrations had two partially miscible liquid phases, while higher NaI concentrations had solid particles. Considering the fully molten regime, electrical conductivities were evaluated over 5–25 mol% NaI and 110 °C–140 °C. Conductivities of 6.8–38.9 mS cm −1 were observed, increasing with temperature and NaI concentration. Effective diffusion coefficients of the I − /I 3 − redox species were found to decrease with both increasing NaI concentration and increasing applied potential. Regardless, oxidation current density at 3.6 V vs Na/Na + was observed to increase with increasing NaI concentration over 5–25 mol%. Finally, the critical interface between the molten salt electrolyte and electrode materials was found to significantly affect reaction kinetics. When carbon was used instead of tungsten, an adsorbed species, most likely I 2 , blocked surface sites and significantly decreased current densities at high potentials. This study shows the NaI-AlBr 3 system offers an attractive, low-temperature molten salt electrolyte that could be useful to many applied systems, though composition and electrode material must be considered.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Rapid dissolution of PuO 2 analytical samples using mediated electrochemical oxidation

Current methods for quantitative dissolution of solid PuO 2 involve lengthy dissolution times. The adaptation of mediated electrochemical oxidation, which uses an electrochemically produced oxidizing agent to catalyze dissolution, has been explored for radiochemical analysis scale dissolutions of PuO 2 . The effects of temperature, electrode material, and electrocatalyst on the dissolution kinetics were explored. Under conditions examined in this study, complete dissolution of tens of milligrams of solid PuO 2 can be achieved in less than 1 h at ambient temperature. Overall, this methodology could be adapted to dissolve other metal oxides.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2026

Modulating Operational Conditions to Mitigate Deactivation in Formate Dehydrogenation on Pd Phases

In heterogeneous catalysis, poisoning by surface-bound intermediates poses a major barrier to sustained catalyst performance in (de)hydrogenation reactions. Formate/bicarbonate systems, as liquid organic hydrogen carriers (LOHCs), offer a CO 2 -integrated, low-temperature pathway for hydrogen storage and release, making them attractive for circular energy applications. However, their lower hydrogen density and susceptibility to catalyst deactivation limit their competitiveness compared to conventional LOHCs like methylcyclohexane. Here, this study investigates the mechanistic origins of formate (HCOO – ) dehydrogenation and associated deactivation on Pd interfaces. Using density functional theory (DFT) simulations, we show that under thermocatalytic conditions, strongly bound formate accumulates on the catalyst surface (Pd(111)), blocking active sites, raising activation barriers, and leading to progressive performance loss. Because formate adsorption involves charge transfer, we exploit its sensitivity to electronic structure by modulating the electrochemical potential of the catalyst. Our results reveal that hydrogen transfer from water and formate exhibits opposing potential dependencies, providing insights into the opposing driving forces behind both catalytic activity and poisoning. To further probe this phenomenon, we examine electrochemically induced phase transitions in Pd, focusing on PdO(100) and PdH(110), which are stable under oxidizing and reducing potentials, respectively, and demonstrate enhanced dehydrogenation activity between −0.4 and 0.2 V vs standard hydrogen electrode (SHE). Complementary thermal treatments help decouple kinetic and thermodynamic contributions to intermediate binding. These findings underscore the critical role of the catalyst phase and external stimuli in dictating poison-active site interactions and highlight phase engineering as a promising strategy to mitigate deactivation. This work offers mechanistic insights and design principles for developing more resilient and efficient catalysts for LOHC applications under realistic operating conditions.

Pd phase↗
DOE OSTI2021

Why halides enhance heterogeneous metal ion charge transfer reactions

Halide-induced rate enhancements are correlated with the desorption barriers of aqueous metal–anion complexes on electrodes, which can guide electrode and electrolyte selection to enhance redox kinetics of metal ion charge transfer reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Electric field distribution in a non-self-sustained RF discharge with ionization generated by Ns discharge pulses

Abstract Electric field in a capacitively coupled, non-self-sustained RF discharge nitrogen plasma with external ionization generated by high-voltage ns pulses has been measured by ps Electric field induced second harmonic generation (EFISH). The measurements are made both in the bulk of the plasma and in the sheaths, using the absolute calibration by the Laplacian field between two plane electrodes. The results are compared with the kinetic modeling calculations. The RF electric field in the sheaths is significantly higher compared to that in the plasma, due to the displacement of the electrons by the drift oscillations and the resultant plasma self-shielding. However, the kinetic modeling predictions indicate that the electron impact ionization in the sheaths is largely ineffective, due to the low electron density. The reduction of the electric field in the plasma by the self-shielding in the sheaths is moderate, such that the energy is coupled to the plasma by the below-breakdown RF field. The peak RF field in the plasma is in the range of 15–25 Td, indicating the efficient vibrational excitation of N 2 by electron impact. The modeling predictions suggest that the targeted vibrational excitation of molecular species in a non-self-sustained RF discharge with external ionization is scalable to high pressures, electron densities, and discharge powers. The present approach can be extended to the vibrational excitation of other molecular species where the vibrational relaxation is relatively slow, such as CO, CO 2 , and H 2 .

Physics↗
DOE OSTI2023

Nanosecond Laser Annealing of NMC 811 Cathodes for Enhanced Performance

Improved performance of lithium-ion batteries (LIBs) plays a critical role in the future of next- generation battery applications. Nickel-rich layered oxides such as LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC 811), are popular cathodes due to their high energy densities. However, they suffer from high surface reactivity, which results in the formation of Li 2 CO 3 passive layer. Herein, we show the role of nanosecond pulsed laser annealing (PLA) in improving the current capacity and cycling stability of LIBs by reducing the carbonate layer, in addition to forming a protective LiF layer and manipulating the NMC 811 microstructures. We use high-power nanosecond laser pulses in a controlled way to create nanostructured surface topography which has a positive impact on the capacity retention and current capacity by providing an increased active surface area, which influences the diffusion kinetics of lithium-ions in the electrode materials during the battery cycling process. Advanced characterizations show that the PLA treatment results in the thinning of the passive Li 2 CO 3 layer, which is formed on as-received NMC811 samples, along with the decomposition of excess polyvinylidene fluoride (PVDF) binder. The high-power laser interacts with the decomposed binder and surface Li + to form LiF phase, which acts as a protective layer to prevent surface reactive sites from initiating parasitic reactions. As a result, the laser treated cathodes show relative increase of the current capacity of up to 50%, which is consistent with electrochemical measurements of LiB cells.

25 ENERGY STORAGE↗
DOE OSTI2023

Catalytic Activity and Stability of Non-Platinum Group Metal Oxides for the Oxygen Evolution Reaction in Anion Exchange Membrane Electrolyzers

The activities and stabilities of non-platinum group metals (PGMs) in the forms of monometallic (Mn 2 O 3 , Fe 2 O 3 , Co 3 O 4 , NiO) and bimetallic (NiFe 2 O 4 , CoNiO 2 ) oxides were assessed for the oxygen evolution reaction (OER) in alkaline media and compared with IrO 2 . Both half-cell, rotating disc electrode (RDE) apparatus and single-cell, membrane electrode assemblies (MEA) were used to study kinetic and device-level performance in parallel and to provide insights into the use of these materials in anion exchange membrane (AEM) electrolyzers. Normalization of RDE results by geometric and physical surface areas, double layer capacitance, and metal content probed differences in physically vs electrochemically accessible surface areas and ensured reported trends were independent of the normalization method. The results showed that: (i) Ni- and Co- containing materials met or exceeded IrO 2 performance in both RDE and MEA testing, (ii) Co 3 O 4 deactivated over time-on-stream (1.8 V for 13.5 h) due to oxide and, relatedly, particle growth, (iii) NiFe 2 O 4 increased in activity over time-on-stream due to dissolution of Fe and an increased Ni/Fe ratio, and (iv) reduction of catalyst layer resistance is an avenue to further increase device-level performance. These results demonstrated the clear viability for non-PGMs to be used as anode catalysts in AEM devices.

25 ENERGY STORAGE↗
DOE OSTI2025

A Full-Cell Model for Direct Toluene Electro-Hydrogenation Electrolysis

Liquid organic hydrogen carriers (LOHCs) are organic molecules that undergo a hydrogenation/dehydrogenation cycle to enable storage and transportation of hydrogen fuel under ambient conditions. One promising LOHC candidate is toluene, which can be converted to methylcyclohexane (MCH) electrochemically, enabling a decarbonized process when green electricity is used. In this study, we developed a full-cell model for the direct electro-hydrogenation of toluene to MCH, utilizing a zero-gap membrane electrode assembly architecture. The model incorporates electrochemical kinetics, ionic transport, water transport across the membrane, and mass transport effects. Electrochemical kinetics are characterized using Tafel analysis on Pt/Ru catalyst. The model is validated against experimental data, including polarization curves, Faradaic efficiencies, and water crossover. A voltage breakdown analysis shows that the performance is dominated by kinetic losses, and the model is used to carry out a comparison of different toluene electro-hydrogenation reaction catalysts. Finally, a sensitivity analysis is conducted on key design parameters illustrating which can be modified to maximize electrolyzer performance. The cathode specific surface area and cathode porous transport layer thickness (PTL) have the largest impact on the current density, while the PTL thickness and Pt loading in the PTL have the largest impact on Faradaic efficiency.

Ehlinger, Victoria M. [Lawrence Livermore National↗
DOE OSTI2022

Effect of Intermediate Semiconducting TiOx Thin Films on Nanoparticle-Mediated Electron Transfer: Electrooxidation of CO

The concept of nanoparticle-mediated electron transfer (eT) across insulating thin films was elucidated theoretically by Allongue and Chazalviel in 2011. In their model, metal nanoparticles (NPs) are immobilized atop passivating, self-assembled monolayers (SAMs). They found that under certain conditions, related to the thickness of the SAM and the size of the NPs, efficient faradaic oxidation and reduction reactions could proceed at the NP surface. In the absence of NPs, however, eT was suppressed by the insulating SAM thin films. Allongue and Chazalviel concluded that, within certain bounds, eT is mediated by fast tunneling between the conductive electrode and the metal NPs, while the kinetics of the redox reaction are controlled by the NPs. This understanding has been confirmed using a variety of experimental models. The theory is based on electron tunneling; therefore, the nature of the intervening medium (the insulator in prior studies) should not affect the eT rate. In the present manuscript, however, we show that the theory breaks down under certain electrochemical conditions when the medium between conductors is an n-type semiconductor. Specifically, we find that in the presence of either Au or Pt NPs immobilized on a thin film of TiOx, CO electrooxidation does not proceed. In contrast, the exact same systems lead to the efficient reduction of oxygen. At present, we are unable to explain this finding within the context of the model of Allongue and Chazalviel.

Galyamova, Aigerim↗