SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The objective of this work is to create an accurate elastic-plastic J2 plasticity model calibration for the Inconel 718 material at room temperature for use in finite element models. This calibration was made using a power-law hardening model of form σ = σ y + $Aε^{n}_{p}$ where A and n are empirically determined constants, and σ y is the proportional limit.
Thermomechanical analysis (TMA) is used to measure the dimensional changes in a sample as a function of temperature. TMA allows for several modes of analysis, with expansion and compression being the most common. TMA is based on the theory of dilatometry and relies on the fact that polymers are viscoelastic materials, possessing both viscous and elastic properties. TMA yields information about the thermal effects on a polymer such as shrinkage, expansion, softening, melting, glass transition temperature and allows for the calculation of the coefficient of thermal expansion (CTE), which can be useful for many applications of polymers.
Thermomechanical analysis (TMA) is used to measure the dimensional changes in a sample as a function of temperature. TMA allows for several modes of analysis, with expansion and compression being the most common. TMA is based on the theory of dilatometry and relies on the fact that polymers are viscoelastic materials, possessing both viscous and elastic properties. TMA yields information about the thermal effects on a polymer such as shrinkage, expansion, softening, melting, glass transition temperature and allows for the calculation of the coefficient of thermal expansion (CTE), which can be useful for many applications of polymers.
Sapphire (Al 2 O 3 ) is a commonly used dielectric material with many applications in lasers and optical systems. Owing to its high resistivity to laser induced damage, it is particularly suitable for use in high power laser systems. This work focuses on developing techniques to characterize material modifications in sapphire. These techniques were applied following localized laser induced ablation, commonly referred to as laser-damage, resulting from exposure to single 100-ps and 6-ns pulses. Measurements of fluorescence-based piezospectroscopy and confocal Raman microscopy were performed with spatial resolution on the order of 1 μ m. Raman microscopy reveals that the relaxation of material exposed to the rapid laser heating, elastic and viscoplastic deformation, melting, and solidification leads to the formation of a polycrystalline material phase. In addition, narrowband fluorescence lines, referred to as R 1 and R 2 , exhibit pressure-sensitive changes to their spectral profiles, allowing 3D internal stresses to be recorded with spatial resolution of the order of a few micrometers.
A fabric-enriched continuum breakage mechanics (F-CBM) framework is developed to examine the relation between elastic and inelastic anisotropy in granular materials subjected to high pressure. For this purpose, emphasis is given to the influence of the anisotropic fabric on the plastic cap regime – that is, a macroscopic signature of the inelasticity of granular materials widely dependent on the particle crushability. Anisotropic behaviour prior to yielding is introduced through a symmetric second-order fabric tensor embedded in the expression of the elastic energy potential. It is shown that, thanks to its energy-based formulation, the F-CBM framework provides a platform to predict the rotation and distortion of the yield cap of granular materials as an outcome of anisotropic strain energy storage prior to grain crushing. Parametric analyses indicate that both the degree of anisotropy and the orientation of the fabric have an impact on the energy release resulting from grain crushing and contribute to the resulting stress–strain behaviour. It is shown that, despite the use of very few parameters, the proposed framework can accurately predict the anisotropic yielding and inelastic stress–strain response solely on the basis of the directional properties inferred from measurements of elastic anisotropy.
We report crystalline black nitrogen (BN) is an allotrope of nitrogen with the black phosphorus (BP) structure recently synthesized at high pressure by two independent research groups. Here, we present a systematic study of the electronic and optical properties of BN focusing on its comparison with BP. To this end, we use the state-of-the-art quasiparticle self-consistent GW approach with vertex corrections in both the electronic and optical channels. Despite many similarities, the properties of BN are found to be considerably different. Unlike BP, BN exhibits a larger optical gap (2.5 vs 0.26 eV), making BN transparent in the visible spectral region with a highly anisotropic optical response. This difference can be primarily attributed to a considerably reduced dielectric screening in BN, leading to enhancement of the effective Coulomb interaction. Despite relatively strong Coulomb interaction, exciton formation is largely suppressed in both materials. Our analysis of the elastic properties shows exceptionally high stiffness of BN, comparable to that of diamond.
Thermal spray processing of metals and respective blends is becoming increasingly attractive due to the unique properties such as increased yield strength, low ductility, and differences in tensile and compressive strengths that result from microstructural features due to the spray process compared to other additive manufacturing methods. Here we report the results of plate impact experiments applied to Controlled Atmosphere Plasma Spray deposits of tantalum (Ta), niobium (Nb), and a tantalum-niobium blend (TaNb). These methods allowed for definition of the Hugoniot for each material type and the assessment of the Hugoniot Elastic Limit (HEL). Spallation experiments were conducted, and soft recovery of each material type allowed for scanning electron microscopy to characterize the fracture mechanism during tensile loading.
Defects are important because they heavily influence material properties (e.g. strength, ductility, elasticity, conductivity, phase transformation temperatures (melting point), corrosion resistance, etc.). At LANL defects in plutonium are being characterized using many different methods (e.g. EXAFS, XRD, microscopy, RUS, DSC, dilatometry, density, etc.) My goal is to introduce a complimentary method of understanding defects in δ-Pu using the mechanical microscope concept. Using well-developed theories of first principles strengthening mechanisms (i.e. how defects influence strength) and carefully designed experiments, mechanical testing can compliment other defect characterization tools.
Additive manufacturing has the potential to be used for repair of high-value parts, but the strength and integrity of such repaired parts, especially under dynamic loading, in still unknown. This work presents the results of high strain-rate dynamic testing of additively repaired stainless steel samples. The 316L samples were intentionally damaged and subsequently repaired with 308L stainless steel wire using electron beam additive manufacturing. The repaired samples were subjected to gas-gun impact testing to induce incipient damage and determine the role played by the repaired region in dictating damage and failure. The results show the following: 1) the equation of state of the repaired region is comparable to the original material as shown by the unchanged spall plane location, 2) the deformation behavior is similar to the original material as shown by the similar Hugoniot Elastic limit, 3) the spall strength of the repaired region is slightly higher than the original material due to varying grain size, and 4) the damage morphology in the repaired region is different and involves a high rate of void coalescence. In conclusion, despite these minor differences in the spall strength and the damage morphology, the overall dynamic response of the original material and repaired samples is similar suggesting that AM is a promising approach for repairing high-value components.
Mechanical shock events experienced by electronics systems can be reproduced in the laboratory using Hopkinson bar tests. In these tests a projectile strikes an bar, creating a pulse which travels through the bar into the system. The quality of these tests depends on the closeness of the shape of the incident pulse to the shape specified for the test. This paper introduces a new way to control the shape of the incoming pulse, through the use of elastic metamaterial concepts. Two dispersion-modifying material concepts, phononic crystals, and local resonators, are examined for their wave shaping capabilities in 1D elastic waveguides. They are then evaluated using a transfer matrix method to determine the output wave shape in the time domain. The concepts are then optimized for various pulse shapes, showing that they are most effective when they are tuned to introduce dispersion near the fundamental frequency of the incident wave.
Bulk metallic glasses (BMGs) are promising structural materials owing to their high elastic limit and yield strength-to-weight ratio. While BMGs also exhibit attractive tribological properties (e.g., high wear resistance), the scientific basis for this behavior is not yet established. In particular, tribologically-induced changes in surface chemistry upon sliding are still an open topic of research. Here, we evaluated by X-ray photoelectron spectroscopy (XPS) the evolution of the surface chemistry of Vitreloy 105 (a Zr-rich BMG) upon sliding under different contact conditions against a tungsten carbide countersurface. The spectroscopic results indicate that the relative fraction of the metallic elements in the near-surface region is not affected by the sliding speed when the applied contact pressure is lower than 1.37 GPa, while a decrease in metallic zirconium was observed at lower sliding speeds and higher applied contact pressure (i.e., 1.71 GPa). Based on the spectroscopic results, a model is proposed for the effect of mechanical stress on the extent of oxidation of the near-surface region of Zr-based BMGs. In conclusion, the results of this work provide novel insights into the surface phenomena occurring on BMGs upon sliding and add significantly to our understanding of the tribological response of this class of promising structural materials.
The mechanical behavior of two-dimensional (2D) materials across 2D phase changes is unknown, and the finite temperature (T) elasticity of paradigmatic SnSe monolayers—ferroelectric 2D materials turning paraelectric as their unit cell turns from a rectangle into a square—is described here in a progressive manner. To begin with, their zero–T total energy landscape gives way to (Boltzmann-like) averages from which the elastic behavior is determined. Furthermore, these estimates are complemented with results from the strain-fluctuation method, which employs the energy landscape or ab initio molecular dynamics data. All approaches capture the coalescence of elastic moduli < C 11 (T) > = < C 22 (T) > due to the structural transformation. The broad evolution and sudden changes of elastic parameters < C 11 (T) >, < C 22 (T) >, and < C 12 (T) > of these atomically thin phase-change membranes establishes a heretofore overlooked connection among 2D materials and soft matter.
The interface between the Earth and the atmosphere forms a strong contrast in material properties. As such, numerical issues can arise when simulating an elastic wavefield across such a boundary when using a numerical simulation scheme. This is exacerbated when two different simulation codes are coupled straddling that interface. In this report we document how we implement the coupling of CTH, a nonlinear shock physics code, to a linearized elastic/acoustic wave propagation algorithm, axiElasti, across the air-earth interface. We first qualitatively verify that this stable coupling between the two algorithms produces expected results with no visible effects of the coupling interface. We then verify the coupling interface quantitatively by checking consistency with results from previous work and with coupled acoustic-elastic seismo-acoustic source inversions in three earth materials.
Due to the intertwining between electronic nematic and elastic degrees of freedom, lattice defects and structural inhomogeneities commonly found in crystals can have a significant impact on the electronic properties of nematic materials. Here, we show that defects commonly present at the surface of crystals generally shift the wave-vector of the nematic instability to a non-zero value, resulting in an incommensurate electronic smectic phase. Such a smectic state onsets above the bulk nematic transition temperature and is localized near the surface of the sample. We argue that this effect may explain not only recent observations of a modulated nematic phase in iron-based superconductors, but also several previous puzzling experiments that reported signatures consistent with nematic order before the onset of a bulk structural distortion.
In the continuum limit, the theory of dislocations in crystals predicts a divergence in the elastic energy of the host material at a crystal geometry dependent limiting (or critical) velocity vc. Explicit expressions for vc are scattered throughout the literature and are available in analytic form only for special cases with a high degree of symmetry. The fact that in some cases (like pure edge dislocations in fcc) v c happens to coincide with the lowest shear wave speed of a sound wave traveling parallel to the dislocation's gliding direction has led to further confusion in the more recent literature. The aim of this short review therefore is to provide a concise overview of the limiting velocities for dislocations of arbitrary character in general anisotropic crystals, and how to efficiently compute them, either analytically or numerically.
The High-Luminosity LHC Accelerator Upgrade Project (HL-LHC AUP) is approaching the production phase of the US-contributed Q1 and Q3 Interaction Region Quadrupoles (MQXFA). The structures for the MQXFA prototypes were design and inspected by the US-LARP (LHC Accelerator Research Program), AUP developed criteria, which will be used for the pre-series structures. As the first two full-length prototypes with 4.2 m magnetic length, MQXFAP1 and MQXFAP2, were designed and assembled at Lawrence Berkeley National Laboratory (LBNL), and tested at Brookhaven National Laboratory (BNL). The end aluminum short shell of MQXFAP2 was fractured along the shell length during the test, and tests were stopped. Analytical and Finite Element analysis were performed in light of the graded procedure defined in the Structure Design Criteria to investigate the fracture failure for MQXFAP2. In this paper, we report the fracture analysis of the current shell design, including the elasto-plastic simulations with submodel technique, and calculations with Linear Elastic Fracture Mechanics (LEFM). Test material properties are also presented. The results of this analysis explain why the end shell of MQXFAP2 failed, and suggest fillets on the end shell notches to meet the margin specified in the Structural Design Criteria.
We present a computational study and framework that allows us to study and understand the crack nucleation process from forging flaws. Forging flaws may be present in large steel rotor components commonly used for rotating power generation equipment including gas turbines, electrical generators, and steam turbines. The service life of these components is often limited by crack nucleation and subsequent growth from such forging flaws, which frequently exhibit themselves as non-metallic oxide inclusions. The fatigue crack growth process can be described by established engineering fracture mechanics methods. However, the initial crack nucleation process from a forging flaw is challenging for traditional engineering methods to quantify as it depends on the details of the flaw, including flaw morphology. We adopt the peridynamics method to describe and study this crack nucleation process. For a specific industrial gas turbine rotor steel, we present how we integrate and fit commonly known base material property data such as elastic properties, yield strength, and S-N curves, as well as fatigue crack growth data into a peridynamic model. The obtained model is then utilized in a series of high-performance two-dimensional peridynamic simulations to study the crack nucleation process from forging flaws for ambient and elevated temperatures in a rectangular simulation cell specimen. The simulations reveal an initial local nucleation at multiple small oxide inclusions followed by micro-crack propagation, arrest, coalescence, and eventual emergence of a dominant micro-crack that governs the crack nucleation process. The dependence on temperature and density of oxide inclusions of both the details of the microscopic processes and cycles to crack nucleation is also observed. The results are compared with fatigue experiments performed with specimens containing forging flaws of the same rotor steel.
Here we report the dependence of mechanical properties and ionic conductivity of the Na 1+ x Mn x /2 Zr 2– x /2 (PO 4 ) 3 (designated as NMZP) ionic conductor on its composition (with x = 0.5, 1.0, 1.5, and 2.0). Local mechanics was studied by instrumented nanoindentation, and the properties of interest included the elastic modulus, hardness, and fracture toughness. Overall, the material becomes more compliant and soft with the increase in the Na content. The elastic modulus reduces from 120 to 80 GPa, and nanoindentation hardness reduces from 7.8 to 4.2 GPa when x changes from 0.5 to 2.0. The relationship with fracture toughness ( K C ) is highly nonlinear: fracture toughness first decreases and then increases with the increase in the sodium content, reaching a maximum value of 0.89 MPa × m 1/2 at x = 2.0. Such a relationship was found to correlate with the formation of a glassy phase in NMZP at intermediate Na concentration. The maximum ionic conductivity coincides with the maximum fracture toughness in this material.