SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A series of photographs taken with Osaka University's high temperature 3MV electron microscope of alpha-A1(z)O(3) at 2000 C is presented. The dynamic study shows grain boundary migration in progress and demonstrates that disappearance of voids is controlled by boundary migration.
The focus was in two broad areas during the most recent 6-month period: (1) the nature and dynamics of time dependent deformation and stress along major seismic zones; and (2) the nature of long-wavelength oceanic geoid anomalies in terms of lateral variations in upper mantle temperature and composition. The principle findings are described in the accompanying appendices.
Rarefied gas dynamics - second-order boundary layer theory applied to heat transfer at stagnation point of sphere in supersonic flow
The fidelity of flux estimates from an atmospheric inversion depends on the ability of atmospheric transport models to simulate the measured quantity. For species such as CO2, with surface fluxes and a large network of surface measurements, this means correctly simulating the dynamics of the planetary boundary layer (PBL), which is one of the most uncertain aspects of atmospheric transport modeling. In contrast, the simulated total column average mole fraction of CO2 (XCO2) is largely insensitive to simulated PBL dynamics. Therefore, measurements of XCO2 provided by current and future short wave infrared (SWIR) greenhouse gas (GHG) satellites such as GOSAT and the OCO family would seem to be more appropriate to flux inversions, as far as minimizing transport model errors (the "noise") is concerned. Unfortunately, the flux-induced variation of CO2 (the "signal") is the largest within the PBL and smallest in XCO2. Therefore, assimilating XCO2 as opposed to PBL CO2 need not give us the strongest "signal to noise" in flux inversions. Recent work on GOSAT and OCO2 retrievals suggest that SWIR satellite spectra may be used to estimate a lower partial column CO2, which could be assimilated in a flux inversion, instead of XCO2.Here we report on a study to assess whether there is an optimal partial column average CO2, intermediate between PBL CO2 and XCO2, whose assimilation might yield the best signal to noise in flux inversions, where (as before) "signal" is the flux-induced variation and "noise" is the error in transport modeling. We simulate atmospheric CO2 with five different global transport models and a common surface CO2 flux over ten years. We consider the spread across the five models to be a proxy for transport model error (the "noise"), and the common variation of CO2 in all five models to be a proxy for the "signal". We compare these signals and noises at different spatiotemporal scales for different partial column specifications to investigate whether there exists an optimal partial column that has large surface flux-driven variations and yet is relatively insensitive to errors in transport models. Finally, we comment on the feasibility of estimating such a partial column from current and future SWIR GHG satellites in the light of recent work on vertically resolved CO2 from current SWIR GHG satellites.
Computer-drawn diagrams of the boundaries between quasi-perpendicular and quasi-parallel areas of earth's bow shock are displayed for a few selected cone angles of static interplanetary magnetic field (IMF). The effect on the boundary of variable IMF in the foreshock is also discussed and shown for one nominal case. The boundaries demand caution in applying them to the realistic, dynamic conditions of the solar wind and in interpreting the effects of small cone angles on the distributions of structures at the shock. However, the calculated, first-order boundaries are helpful in defining areas of the shock where contributions from active structures inherent in quasi-parallel geometry may be distinguishable from those derived secondarily from upstream reflected ion dynamics. The boundaries are also compatible with known behavior of daytime ULF geomagnetic waves and pulsations according to models postulating that cone angle-controlled, time-dependent ULF activity around the subsolar point of the bow shock provides the source of geomagnetic excitation.
Magnetohydrodynamics (MHD) constitutes the simplest comprehensive and self-consistent formulation of the properties of space plasmas. As such, it has been applied with large success to the dynamics of solar system plasmas. For the nightside region of the Earth, the magnetotail, MHD simulations have led to new understanding of the structure and dynamics of the plasmas, in response to both changes in boundary conditions as well as internal dynamical processes. As a result, substantial knowledge of the structure and dynamics of the nightside region have been accumulated. In basic MHD conservation laws on magnetospheric structure, as well as the role of non-MHD processes in the initiation and evolution of dynamical processes of the magnetotail. This presentation will consist of three parts, the first of which addresses the basic constraints on magnetotail structure as well as their consequences for magnetotail specification and forecasting. We will then review some examples of magnetotail structural changes brought about by solar-wind-like boundary conditions. Last, we consider the role of non-MHD processes in magnetotail specification and forecasting. The emphasis here will be on inclusion of these processes into MHD models, and their impact on the overall structure and dynamics.
Explore the source record for details and available documents.
The focus of the research was in two broad areas during the most recent 6 month period: the nature and dynamics of time-dependent deformation along major seismic zones, including the influence of irregularities in fault geometry on the earthquake cycles, and the processes contributing to the state of stress and rates of strain in plate interior regions. The principal findings of the research to date are described.
Turbulent boundary layer flow in conical supersonic nozzle, discussing convective heat transfer and adverse pressure gradient effect
The flutter model represented the aft fuselage and empennage of a proposed supersonic transport airplane and had an all movable horizontal tail with a geared elevator. It was tested mounted from a sting in the transonic dynamics tunnel. Symmetric flutter boundaries were determined experimentally at Mach numbers from 0.7 to 1.14 for a geared elevator configuration (gear ratio of 2.8 to 1.0) and an ungeared elevator configuration (gear ratio of 1.0 to 1.0). Gearing the elevator increased the experimental flutter dynamic pressures about 20 percent. Flutter calculations were made for the geared elevator configuration by using two analytical methods based on subsonic lifting surface theory. Both methods analyzed the stabilizer and elevator as a single, deforming surface, but one method also allowed the elevator to be analyzed as hinged from the stabilizer. All analyses predicted lower flutter dynamic pressures than experiment with best agreement (within 12 percent) for the hinged elevator method. Considering the model as mounted from a flexible rather than rigid sting in the analyses, had only a slight effect on the flutter results but was significant in that a sting related vibration mode was identified as a potentially flutter critical mode.
A nonlinear dynamic model with full flight envelope controller is developed for the propulsion system of a partially turboelectric single-aisle aircraft. The propulsion system model consists of two turbofan engines with a large percentage of power extraction, feeding an electric tail fan for boundary layer ingestion. The dynamic model is compared against an existing steady state design model. An electrical system model using a simple power flow approach is integrated into existing modeling tools used for dynamic simulation of the turbomachinery of the vehicle. In addition to the simple power flow model of the electrical system, a more detailed model is used for comparison at a key vehicle transient flight condition. The controller is a gain scheduled proportional-integral type that is examined throughout the flight envelope for performance metrics such as rise time and operability margins. Potential improvements in efficiency for the vehicle are explored by adjusting the power split between the energy used for thrust by the turbofans and that extracted to supply power to the tail fan. Finally, an operability study of the vehicle is conducted using a 900 nautical mile mission profile for a nominal vehicle configuration, a deteriorated propulsion system at the end of its operating life, and an optimized power schedule with improved efficiency.
Implicit large-eddy simulation (ILES) of a shock wave/boundary-layer interaction (SBLI) was performed. Quantities present in the exact equation of the turbulent kinetic energy transport were accumulated and used to calculate terms like production, dissipation, molecular diffusion, and turbulent transport. The present results for a turbulent boundary layer were validated by comparison with direct numerical simulation data. It was found that a longer development domain was necessary for the boundary layer to reach an equilibrium state and a finer mesh resolution would improve the predictions. In spite of these findings, trends of the present budget match closely with that of the direct numerical simulation. Budgets for the SBLI region are presented at key axial stations. These budgets showed interesting dynamics as the incoming boundary layer transforms and the terms of the turbulent kinetic energy budget change behavior within the interaction region.
Discrete ordinate method for boundary value problems in gas dynamics using differential equations yields solutions to Couette flow
Prediction characteristics of separated turbulent boundary layers in compression corners used to determine aerodynamic heating distributions and dynamic loading of supersonic vehicles
Computational finite-element and boundary-element methods are reviewed, and their application to the mechanics of solids is discussed. Stability conditions for general FEMs are considered in addition to the use of least-order, stable, invariant, or hybrid/mixed isoparametric elements as alternatives to the displacement-based isoparametric elements. The use of symbolic manipulation, adaptive mesh refinement, transient dynamic response, and boundary-element methods for linear elaslticity and finite-strain problems of inelastic materials are also discussed.
The First ISCCP Regional Experiment (FIRE) marine stratocumulus Intensive Field Observation (IFO) held in July, 1987 produced a data set that is far more comprehensive than data sets from previous stratocumulus experiments. One exciting new development was the use of the 10.6 micron lidar system for cloud-top mapping that was available on the National Center for Atmospheric Research (NCAR) Electra. This system provided a unique look at the small scales of the turbulence in the clouds, images of the turbulent structures that are quantitatively revealed by conditional sampling (e.g., Khalsa and Greenhut, 1987). The behavior of these updrafts and downdrafts is central to the dynamics of the stratocumulus-topped marine boundary layer. FIRE's objectives of understanding cloud dynamics and how they affect the cloud optical depth - which, in turn, is the crucial factor in determining the clouds' albedo - therefore require the investigation of these drafts. Given here are initial results from a simple model capable of simulating moist, entraining plumes that are subject to water phase changes and radiative heating and cooling. These results correspond, therefore, to the 'dry cloud' case discussed by Lilly and Schubert (1980). The model's simplicity limits the realism of the results - the plumes are assumed not to interact, for example - but the role of radiative processes in influencing the plume dynamics is clear. Also revealed is the role the plumes play is maintaining the cloud-top inversion. The model equations and methodology used, and qualitative results are given.
The recent experimental transfer matrices obtained by Ng and Brennen (1978) for some axial flow pumps revealed some dynamic characteristics which were unaccounted for by any existing theoretical analysis; their visual observations suggested that the bubbly cavitating flow in the blade passages could be responsible for these effects. A theoretical model of the dynamic response of this bubbly blade-passage flow is described in the present paper. Void-fraction fluctuations in this flow result not only from pressure fluctuations but also because the fluctuating angle of attack causes fluctuations in the rate of production of bubbles near the leading edge. The latter causes kinematic waves which interact through the boundary conditions with the dynamic waves caused by pressure fluctuation. The resulting theoretical transfer functions which results are in good qualitative agreement with the experiments; with appropriate choices of two parameters good quantitative agreement is also obtained. The theoretical model also provides one possible explanation of the observation that the pump changes from an essentially passive dynamic element in the absence of cavitation to a progressively more active element as the extent of cavitation increases.
The Melick method of inlet flow dynamic distortion prediction by statistical means is outlined. A hypothetic vortex model is used as the basis for the mathematical formulations. The main variables are identified by matching the theoretical total pressure rms ratio with the measured total pressure rms ratio. Data comparisons, using the HiMAT inlet test data set, indicate satisfactory prediction of the dynamic peak distortion for cases with boundary layer control device vortex generators. A method for the dynamic probe selection was developed. Validity of the probe selection criteria is demonstrated by comparing the reduced-probe predictions with the 40-probe predictions. It is indicated that the the number of dynamic probes can be reduced to as few as two and still retain good accuracy.