SEARCH · Engineering Papers

Results for “drag estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

All sources NASA NTRS DOE OSTI

NASA NTRS1978

Theoretical estimation of the transonic aerodynamic characteristics of a supercritical-wing transport model with trailing-edge controls

A method for rapidly estimating the overall forces and moments at supercritical speeds, below drag divergence, of transport configurations with supercritical wings is presented. The method was also used for estimating the rolling moments due to the deflection of wing trailing-edge controls. This analysis was based on a vortex-lattice technique modified to approximate the effects of wing thickness and boundary-layer induced camber. Comparisons between the results of this method and experiment indicate reasonably good correlation of the lift, pitching moment, and rolling moment. The method required much less storage and run time to compute solutions over an angle-of-attack range than presently available transonic nonlinear methods require for a single angle-of-attack solution.

Luckring, J. M.↗

NASA NTRS2012

A Preliminary Flight Investigation of Formation Flight for Drag Reduction on the C-17 Aircraft

Many theoretical and experimental studies have shown that aircraft flying in formation could experience significant reductions in fuel use compared to solo flight. To date, formation flight for aerodynamic benefit has not been thoroughly explored in flight for large transport-class vehicles. This paper summarizes flight data gathered during several two ship, C-17 formation flights at a single flight condition of 275 knots, at 25,000 ft MSL. Stabilized test points were flown with the trail aircraft at 1,000 and 3,000 ft aft of the lead aircraft at selected crosstrack and vertical offset locations within the estimated area of influence of the vortex generated by the lead aircraft. Flight data recorded at test points within the vortex from the lead aircraft are compared to data recorded at tare flight test points outside of the influence of the vortex. Since drag was not measured directly, reductions in fuel flow and thrust for level flight are used as a proxy for drag reduction. Estimated thrust and measured fuel flow reductions were documented at several trail test point locations within the area of influence of the leads vortex. The maximum average fuel flow reduction was approximately 7-8%, compared to the tare points flown before and after the test points. Although incomplete, the data suggests that regions with fuel flow and thrust reduction greater than 10% compared to the tare test points exist within the vortex area of influence.

Pahle, Joe↗

NASA NTRS2012

An Initial Flight Investigation of Formation Flight for Drag Reduction on the C-17 Aircraft

Joe Pahle↗

NASA NTRS2000

GRACE Mission Design: Impact of Uncertainties in Disturbance Environment and Satellite Force Models

The Gravity Recovery and Climate Experiment (GRACE) primary mission will be performed by making measurements of the inter-satellite range change between two co-planar, low altitude, near-polar orbiting satellites. Understanding the uncertainties in the disturbance environment, particularly the aerodynamic drag and torques, is critical in several mission areas. These include an accurate estimate of the spacecraft orbital lifetime, evaluation of spacecraft attitude control requirements, and estimation of the orbital maintenance maneuver frequency necessitated by differences in the drag forces acting on both satellites. The FREEMOL simulation software has been developed and utilized to analyze and suggest design modifications to the GRACE spacecraft. Aerodynamic accommodation bounding analyses were performed and worst-case envelopes were obtained for the aerodynamic torques and the differential ballistic coefficients between the leading and trailing GRACE spacecraft. These analyses demonstrate how spacecraft aerodynamic design and analysis can benefit from a better understanding of spacecraft surface accommodation properties, and the implications for mission design constraints such as formation spacing control.

Mazanek, Daniel D.↗

NASA NTRS2000

Aerothermal Analysis and Design of the Gravity Recovery and Climate Experiment (GRACE) Spacecraft

The Gravity Recovery and Climate Experiment (GRACE) primary mission will be performed by making measurements of the inter-satellite range change between two co-planar, low altitude near-polar orbiting satellites. Understanding the uncertainties in the disturbance environment, particularly the aerodynamic drag and torques, is critical in several mission areas. These include an accurate estimate of the spacecraft orbital lifetime, evaluation of spacecraft attitude control requirements, and estimation of the orbital maintenance maneuver frequency necessitated by differences in the drag forces acting on both satellites. The FREEMOL simulation software has been developed and utilized to analyze and suggest design modifications to the GRACE spacecraft. Aerodynamic accommodation bounding analyses were performed and worst-case envelopes were obtained for the aerodynamic torques and the differential ballistic coefficients between the leading and trailing GRACE spacecraft. These analyses demonstrate how spacecraft aerodynamic design and analysis can benefit from a better understanding of spacecraft surface accommodation properties, and the implications for mission design constraints such as formation spacing control.

Mazanek, Daniel D.↗

NASA NTRS2012

Aeroelastic Modeling of Elastically Shaped Aircraft Concept via Wing Shaping Control for Drag Reduction

Lightweight aircraft design has received a considerable attention in recent years as a means for improving cruise efficiency. Reducing aircraft weight results in lower lift requirements which directly translate into lower drag, hence reduced engine thrust requirements during cruise. The use of lightweight materials such as advanced composite materials has been adopted by airframe manufacturers in current and future aircraft. Modern lightweight materials can provide less structural rigidity while maintaining load-carrying capacity. As structural flexibility increases, aeroelastic interactions with aerodynamic forces and moments become an increasingly important consideration in aircraft design and aerodynamic performance. Furthermore, aeroelastic interactions with flight dynamics can result in issues with vehicle stability and control. Abstract This paper describes a recent aeroelastic modeling effort for an elastically shaped aircraft concept (ESAC). The aircraft model is based on the rigid-body generic transport model (GTM) originally developed at NASA Langley Research Center. The ESAC distinguishes itself from the GTM in that it is equipped with highly flexible wing structures as a weight reduction design feature. More significantly, the wings are outfitted with a novel control effector concept called variable camber continuous trailing edge (VCCTE) flap system for active control of wing aeroelastic deflections to optimize the local angle of attack of wing sections for improved aerodynamic efficiency through cruise drag reduction and lift enhancement during take-off and landing. The VCCTE flap is a multi-functional and aerodynamically efficient device capable of achieving high lift-to-drag ratios. The flap system is comprised of three chordwise segments that form the variable camber feature of the flap and multiple spanwise segments that form a piecewise continuous trailing edge. By configuring the flap camber and trailing edge shape, drag reduction could be achieved. Moreover, some parts of the flap system can be made to have a high frequency response for roll control, gust load alleviation, and aeroservoelastic (ASE) modal suppression control. Abstract The aeroelastic model of the ESAC is based on one-dimensional structural dynamic theory that captures the aeroelastic deformation of a wing structure in a combined motion that involves flapwise bending, chordwise bending, and torsion. The model includes the effect of aircraft propulsion due to wing flexibility which causes the propulsive forces and moments to couple with the wing elastic motion. Engine mass is also accounted in the model. A fuel management model is developed to describe the wing mass change due to fuel usage in the main tank and wing tanks during cruise. Abstract The model computes both static and dynamic responses of the wing structures. The static aeroelastic deflections are used to estimate the effect of wing flexibility on induced drag and the potential drag reduction by the VCCTE flap system. A flutter analysis is conducted to estimate the flutter speed boundary. Gust load alleviation via adaptive control has been recently investigated to address flexibility of aircraft structures. A multi-objective flight control approach is presented for drag reduction control. The approach is based on an optimal control framework using a multi-objective cost function. Future studies will demonstrate the potential benefits of the approach.

Aeroelasticity↗

NASA NTRS1948

Altitude-Wind-Tunnel Investigation of a 4000-Pound-Thrust Axial-Flow Turbojet Engine: Performance and Windmilling Drag Characteristics - Part 1

The results of altitude-wind-tunnel tests conducted to determine the performance of an axial-flow-type 4000.pound-thrust turboJet engine for a range of pressure altitudes from 5000 to 40,000 feet and ram pressure ratios from 1.02 to 1.86 are presented and the experimental and analytical methods employed are discussed. By means of suitable generalizing factors applied to the measured performance data, curves were obtained from which the engine performance at any altitude for a given ram pressure ratio can be estimated. The data presented include the windmilling drag characteristics of the turbojet engine for the ranges of altitudes and ram pressure ratios covered by the performance data.

Fleming, William A.↗

NASA NTRS1947

Wind-Tunnel Tests of a 0.182-Scale Model of an F4U-1 Airplane with External Stores

Tests were made in the Langley 7- by 10-foot tunnel on a 0.182-scale model of an F4U-1 airplane with external stores. This paper is concerned mainly with presenting the data obtained in this investigation and with a comparison of some of these data with flight-test results determining the feasibility of estimating flight buffet Mach number from tunnel data. The results of this investigation indicate that the incremental drag coefficient due to external stores may be used to estimate the maximum Mach number that the F4U-1 airplane may reach in flight when it is equipped with external stores. This estimation is conservative for the five configurations investigated by mounts varying from 0 to 10 percent of the flight limit Mach number. The free-stream tunnel Mach number corresponding to sonic flow over the lower surface of the wing in the region of the store is a good indication of the lower limit of buffet in flight of the F4U-1 airplane when equipped with external stores. The fluctuations of total pressure over the horizontal tail are not sufficiently large (maximum of 1 percent q(sub o) to cause buffeting of the airplane.

Silvers, H. Norman↗

NASA NTRS1971

Estimation in satellite control.

The use of estimators or observers is discussed as applied to satellite attitude control and the control of drag-free satellites. The practical problems of implementation are discussed, and the relative advantages of full and reduced state estimators are compared, particularly in terms of their effectiveness and bandwidth as filters. Three applications are used to illustrate the principles. They are: (1) a reaction wheel control system, (2) a spinning attitude control system, and (3) a drag-free satellite translational control system. Fixed estimator gains are shown to be adequate for these (and many other) applications. Our experience in the hardware realization of estimators has led to categorize the error sources in terms of those that improve with increased estimator gains and those that get worse with increased estimator gains.

Debra, D. B.↗

NASA NTRS2013

Testing Small CPAS Parachutes Using HIVAS

The High Velocity Airflow System (HIVAS) facility at the Naval Air Warfare Center (NAWC) at China Lake was successfully used as an alternative to flight test to determine parachute drag performance of two small Capsule Parachute Assembly System (CPAS) canopies. A similar parachute with known performance was also tested as a control. Realtime computations of drag coefficient were unrealistically low. This is because HIVAS produces a non-uniform flow which rapidly decays from a high central core flow. Additional calibration runs were performed to characterize this flow assuming radial symmetry from the centerline. The flow field was used to post-process effective flow velocities at each throttle setting and parachute diameter using the definition of the momentum flux factor. Because one parachute had significant oscillations, additional calculations were required to estimate the projected flow at off-axis angles. The resulting drag data from HIVAS compared favorably to previously estimated parachute performance based on scaled data from analogous CPAS parachutes. The data will improve drag area distributions in the next version of the CPAS Model Memo.

Ray, Eric S.↗

NASA NTRS2019

Testing of the Lunar Reconnaissance Orbiter Attitude Control System Re-Design Without a Gyro

The Lunar Reconnaissance Orbiter (LRO) was launched in 2009 and, with itsseven science instruments, has made numerous contributions to our understandingof the moon. LRO is in an elliptical, polar lunar orbit and nominally maintainsa nadir orientation. There are frequent slews off nadir to observe various sciencetargets. LRO attitude control system (ACS) has two star trackers and a gyro forattitude estimation in an extended Kalman filter (EKF) and four reaction wheelsused in a proportional-integral-derivative (PID) controller. LRO is equipped withthrusters for orbit adjustments and momentum management. In early 2018, thegyro was powered off following a fairly rapid decline in the laser intensity on theX axis. Without the gyro, the EKF has been disabled. Attitude is provided by asingle star tracker and a coarse rate estimate is computed by a back differencingof the star tracker quaternions. Slews have also been disabled. A new rate estimationapproach makes use of a complementary filter, combining the quaterniondifferentiated rates and the integrated PID limited control torque (with reactionwheel drag and feedforward torque removed). The filtered rate estimate replacesthe MIMU rate in the EKF, resulting in minimal flight software changes. The paperwill cover the preparation and testing of the new gyroless algorithm, both inground simulations and inflight.

Halverson, Julie↗

NASA NTRSDate not supplied

Real-Time Drag Optimization of Aspect Ratio 13.5 Common Research Model with Distributed Flap System

This paper presents a real-time drag optimization study of the aspect ratio 13.5 Common Research Model (CRM) with a distributed mini-plain flap system. A surrogate aerodynamic model of the aspect ratio 13.5 CRM is developed based on an aerodynamic database computed by a transonic panel method to capture the aerodynamic coefficients as functions of the angle of attack, flap deflections, and Mach number. A recursive least-squares parameter estimation algorithm is designed to estimate the aerodynamic parameters of the surrogate model. The estimated surrogate model is then used in an on-line drag optimization strategy based on an adjoint method. The results of the real-time drag optimization indicate a drag reduction of 2.46% for Mach 0.80, 3.37% for Mach 0.85, and 1.95% for Mach 0.88. The results show the convergence of all parameter estimates.

Drag Optimization↗

NASA NTRS1992

Stress observations and driving force models for the South American plate

A comparison of stress observations to predictions of driving force models for the South American plate is presented. Conditions for dynamical equilibrium are used to estimate the magnitudes of forces as a function of age, with ridge push and slab pull as active forces, and plate drag and slab resistance as passive forces. The results are consistent with earlier published models, and it is found that the primary balance for an oceanic plate is between slab pull and the resisting drag forces. The model is generalized for the possible forces driving the South American plate, and it is compared with observed stress measurements and kinematics. The plate balance is found to be largely between ridge push and plate drag. The magnitude of a possible trench suction force is estimated using a model with an eddy between the Nazca slab and the overlying South American plate.

Stefanick, Michael↗

NASA NTRSDate not supplied

CFD Validation Study of a Hypersonic Cone-Slice-Flap Variable Geometry Configuration

Model validation is the process of determining the degree of accuracy between physical reality and the model. The result of model validation can either be used to improve the model through calibration or quantify the model-form uncertainty. This work focuses on providing the model-form uncertainty through an area metric for a hypersonic cone-slice-flap variable geometry configuration given uncertainty in both the simulation and experimental data. For a variable geometry, performing uncertainty quantification to capture the model-form uncertainty on every configuration is computationally challenging. This work lays out a procedure that can give an accurate representation of the model-form uncertainty using a small number of high-fidelity runs and many low-fidelity runs on multiple configurations. Running this comparison provides a quantifiable measurement for the accuracy of each turbulence model for this type of design. The high-fidelity CFD solver used was VULCAN-CFD and the low-fidelity results came from Cart3D. The experimental data came from the 20-Inch Mach 6 Tunnel located at NASA Langley Research Center. The present work showed that the turbulence simulation overpredicted the drag and lift coefficient, while underpredicting the pitching moment coefficient. The model-form uncertainty estimate resulted up to a 13.6% change in the total uncertainty for the drag coefficient, up to a 57.4% change in total uncertainty for the lift coefficient, and up to a 100% change in total uncertainty for the pitching moment coefficient.

Laura White↗

DOE OSTI2020

Supernova Hydrodynamics: A Lab-scale Study of the Blast-driven Instability Using High-speed Diagnostics

A novel experimental approach to study the blast-driven instability at a nondiffuse, gaseous interface with a density gradient is presented. Under Euler similarity, this approach enables study of dissipative-scale hydrodynamics relevant to many astrophysical and laboratory high energy density phenomena in a well-resolved manner. The instability is initiated by passing a Taylor–Sedov blast wave originating from a controlled detonation through a perturbed and stably stratified interface between two gases. The facility and driving blast wave are characterized to obtain repeatable conditions and capture large ensembles of time-resolved Mie scattering imaging that show consistent hydrodynamic development. We analyze the instability evolution between different gas pairs to demonstrate the wide range of development and turbulent behavior that may occur between different supernova layers. The mean evolution of the hydrodynamic instability is compared to a buoyancy–drag model that is frequently used to estimate perturbation growth in supernova mixing research. We propose a time delay to this model in order to reproduce the measured instability behavior and demonstrate model robustness in handling flows driven by a time-varying acceleration.

79 ASTRONOMY AND ASTROPHYSICS↗

NASA NTRS1975

Aerodynamic characteristics of a tandem wing configuration of a Mach number of 0.30

An investigation was conducted to determine the aerodynamic characteristics of a tandem wing configuration. The configuration had a low forward mounted sweptback wing and a high rear mounted sweptforward wing jointed at the wing tip by an end plate. The investigation was conducted at a Mach number of 0.30 at angles of attack up to 20 deg. A comparison of the experimentally determined drag due to lift characteristics with theoretical estimates is also included.

Henderson, W. P.↗

NASA NTRS1975

Simplified theoretical methods for aerodynamic design

The objective of this paper is to describe theoretical procedures which can be utilized by the general aviation industry for aerodynamic design. Discussed are the design process and theoretical methods used to design a wing. Then theoretical methods for estimating the interference velocities due to fuselage, or other bodies, and nacelles are elaborated. It is assumed that flow fields due to different components can be superimposed, and then the pressure coefficients computed from the Bernoulli equation. Methods to estimate the induced, viscous form, and compressible drags are also discussed. In addition, a procedure for modifying the surface contours to reduce adverse pressure distributions induced by component interference is detailed.

Tulinius, J. R.↗

NASA NTRS1982

Longitudinal aerodynamic characteristics of an elliptical body with a horizontal tail at Mach numbers from 2.3 to 4.63

Longitudinal aerodynamic characteristics of a configuration consisting of an elliptical body with an in plane horizontal tail were investigated. The tests were conducted at Mach numbers of 2.3, 2.96, 4.0, and 4.63. In some cases, the configuration with negative tail deflections yielded higher values of maximum lift drag ratio than did the configuration with an undeflected tail. This was due to body upwash acting on the tail and producing an additional lift increment with essentially no drag penalty. Linear theory methods used to estimate some of the longitudinal aerodynamic characteristics of the model yielded results which compared well with experimental data for all Mach numbers in this investigation and for both small angles of attack and larger angles of attack where nonlinear (vortex) flow phenomena were present.

Shrout, B. L.↗