Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “differential stress”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

3D mapping of residual stresses in growing grains of partially recrystallized Gum Metal

The crystallographic orientations and residual stresses within recrystallizing grains in partially recrystallized beta titanium-Gum Metal-were examined non-destructively in 3D using synchrotron Differential Aperture X-ray Microscopy. Contrary to common assumptions, significant local stresses and stress variations are observed within the recrystallizing grains. The results reveal that the development of these local residual stresses depends on the plastic deformation mode and material's elastic constants, rather than grain properties such as size and orientation, or even the material's yield stress. This work provides insights valuable for the design of advanced materials with heterogeneous microstructures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Control of deviatoric stress in the diamond anvil cell through thermal expansion mismatch stress in thin films

Elastic and plastic properties of materials and phase transitions at extreme conditions vary with both hydrostatic pressure and deviatoric stress. To generate and measure controlled deviatoric stress at pressures beyond those accessible with large volume differential and rotational presses and optical access for spectroscopy, experiments tested the combination of diamond anvil cell and thin film technology. Thin films of polycrystalline Cr-doped Al 2 O 3 ruby were prepared using pulsed laser deposition on single-crystal substrates of either Al 2 O 3 sapphire or yttria-stabilized cubic zirconia for contrasting initial film stress, and loaded in diamond anvil cells for confining stress. The piezospectroscopic response of the ruby films demonstrates consistently higher deviatoric stress in the film on zirconia relative to the film on the control sapphire, and an increase in deviatoric stress with applied load. Complementary synchrotron X-ray diffraction of the zirconia substrate confirmed that no pressure-induced phase transitions impacted the stress state of the ruby film, but differences in compressibility of film and substrate result in changes in film stress analogous to thermal expansion mismatch. Furthermore, this technique may be applied to evaluate elastic and plastic response of thin films of a variety of materials under extreme stress.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Differential Power Processing for Ultra-Efficient Data Storage

Here this paper presents the hardware, software, and power codesign of an ultra-efficient data storage server with differential power processing (DPP). DPP can reduce the power conversion stress, improve the efficiency, and enhance the functionality of modular power electronics systems. The power inputs of a large number of hard disk drives (HDDs) were connected in series and supported by a multiport ac-coupled differential power processing (MAC-DPP) converter through a multiwinding transformer. Methods for controlling the multi-input multi-output power flow in the multiwinding transformer while avoiding core saturation were investigated. A ten-port MAC-DPP prototype with 700-W/in 3 power density was built to support a 450-W HDD storage system with ten series-stacked voltage domains. The prototype was tested on a 50-HDD server testbench, and the overall system loss is below 1 W (99.77% system efficiency). The server was able to maintain high-speed reading and writing operation of all 50 HDDs against the worst hot-swapping scenarios. A variety of hardware/software configurations and many cloud storage techniques were tested on the fully functioning server. Experimental results show that the energy efficiency of large-scale information systems (CPU/GPU clusters, memory banks, HDD arrays, etc.) can be greatly improved by software, hardware, and power codesign.

42 ENGINEERING↗
DOE OSTI2025

Using X-ray radiography to study oxygen flow in a proton exchange membrane electrolyzer operating under balanced pressure conditions

Of the various water electrolyzer technologies, the proton exchange membrane electrolyzer (PEMWE) is one of the best solutions for producing clean hydrogen without releasing CO 2 . In order to allow for widespread use of clean hydrogen, it is necessary to decrease its cost, which is intrinsically related to system operation. Current PEMWE plants operate in differential mode, directly pressurizing hydrogen and benefiting from thermodynamic compression, which increases overall system efficiency. However, high differential pressure above 30 bar can cause membrane stress, resulting in membrane creeping and failure. Pressurizing the water and operating at balanced pressure allows hydrogen to be produced at higher pressures while preserving the integrity of the membrane and porous layers. Nevertheless, the impact of pressurizing water on PEMWE performance must be better understood to maximize performance under balanced pressure conditions. Here, this study examined the impact of water pressure on two-phase flow. A high-pressure electrolyzer setup was developed to perform operando X-ray radiography and examine oxygen transport with high temporal resolution. The imaging segmentation process, developed to capture bubble properties in the channel, was applied to a specific experiment. The results clearly showed that as pressure increased up to 30 bars, the initial bubbly flow transitioned to slug flow, which led to channel saturation with oxygen. This work demonstrates that two-phase flow in an electrolyzer can be studied using X-ray radiography, which has the advantages of fast measurements and the ability to probe dense materials, such as those required for pressurized electrolyzers.

Balanced high pressure operation↗
DOE OSTI2024

Analysis of differential scanning calorimetry data for aged plutonium

Differential scanning calorimetry data for samples of a 52 year old plutonium alloy with 3.3 at. % Ga that were heated beyond the melting point is analyzed using transition state theory to find activation energies for the δ to ε and ε to liquid phase transitions. A Bayesian statistical method involving a Gaussian process model is used to find mean values and confidence intervals for the activation energies. The activation energy for the δ to ε phase transition increases by 3.3 ± 3.8% per decade, relative to the case when all age related plutonium lattice point defects have been removed through annealing. The corresponding increase in activation energy for the ε to liquid transition is shown to be 7.1 ± 1.8% per decade. It is postulated that the change in activation energy with age for both phase transitions is caused, in part, by the accumulation of the same type of lattice point defects associated with the observed increase in elastic bulk modulus over time.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Alternative splicing: transcriptional regulatory network in agroforestry

Alternative splicing (AS) in plants plays a key role in regulating the expression of numerous transcripts from a single gene in a regulatory pathway. Variable concentrations of growth regulatory hormones and external stimuli trigger alternative splicing to switch among different growth stages and adapt to environmental stresses. In the AS phenomenon, a spliceosome causes differential transcriptional modifications in messenger RNA (mRNAs), resulting in partial or complete retention of one or more introns as compared to fully spliced mRNA. Differentially expressed proteins translated from intron-retaining messenger RNA (mRNA ir ) perform vital functions in the feedback mechanism. At the post-transcriptional level, AS causes the remodeling of transcription factors (TFs) by the addition or deletion of binding domains to activate and/or repress transcription. In this study, we have summarized the specific role of AS in the regulation of gene expression through repression and activation of the transcriptional regulatory network under external stimuli and switch among developmental stages.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS1989

Prediction of separated transonic wing flows with a non-equilibrium algebraic model

A nonequilibrium algebraic turbulence model, which is based on the turbulence closure scheme of Johnson and King (1985), is proposed to predict separated transonic wing flows. The influence of history effects are modeled by solving a partial differential equation for the maximum total Reynolds shear stress, which is then used to scale the eddy viscosity of an algebraic model. The turbulence model is implemented in a three-dimensional, Reynolds-averaged Navier-Stokes code. Comparisons with experimental data are presented which show clearly that the nonequilibrium type of turbulence model is essential for accurate prediction of transonic separated flows.

Abid, Ridha↗
NASA NTRS1990

Analyses of composite fuselage structure under various loading conditions

With the characteristics of high strength/weight and stiffness/weight ratios in advanced composite materials, composite plate structures have been successfully applied to secondary load-carrying structural components in the aerospace industry for the past two decades. Recently, filament wound composite shells are being considered for design of primary fuselage structures. To implement the design the structural response under various loading conditions needs to be predicted accurately. Therefore, it is essential to establish a rigorous analytical solution in the area of composite laminated shells. A closed form solution is presented that predicts the response of a composite shell subjected to internal pressure, axial tension, bending, and torsion. The material of the shell is assumed to be general cylindrically anisotropic. Based on the theory of cylindrical anisotropic elasticity coupled partial differential governing equations are developed using Lehknitskii's stress function approach. The general expressions for the stresses and displacements in the composite cylinders under these loading conditions is discussed. Three examples (45) off-axis unidirectional, (45/45) unsymmetric, and (45/45)(sub s) symmetric angle-ply fiber-reinforced laminated shells are shown to illustrate the effect of radius-to-thickness ratios, coupling, and stacking sequence.

Yuan, Fuh-Gwo↗
NASA NTRS1996

Two-phase flow research using the DC-9/KC-135 apparatus

Low-gravity gas-liquid flow research can be conducted aboard the NASA Lewis Research Center DC-9 or the Johnson Space Center KC-135. Air and water solutions serve as the test liquids in cylindrical test sections with constant or variable inner diameters of approximately 2.54 cm and lengths of up to 3.0 m. Superficial velocities range from 0.1 to 1.1 m/sec for liquids and from 0.1 to 25 m/sec for air. Flow rate, differential pressure, void fraction, film thickness, wall shear stress, and acceleration data are measured and recorded at data rates of up to 1000 Hz throughout the 20-sec duration of the experiment. Flow is visualized with a high-speed video system. In addition, the apparatus has a heat-transfer capability whereby sensible heat is transferred between the test-section wall and a subcooled liquid phase so that the heat-transfer characteristics of gas-liquid two-phase flows can be determined.

McQuillen, John B.↗
DOE OSTI2025

Genetic_and_epigenetic_signatures_of_Populus_Trichocarpa_in_response_to_abiotic_stress

Plants respond to abiotic stresses such as drought, heat, and salinity through both shared and stress-specific regulatory pathways. However, the role of epigenetic mechanisms, particularly DNA methylation, in modulating these responses is still underexplored. Here, we integrated transcriptome profiling with whole-genome bisulfite sequencing (WGBS) to investigate the dynamic relationship between gene expression and DNA methylation in Populus trichocarpa during brief early-stage exposure to abiotic stress. Each stress elicited distinct transcriptional and methylation signatures; however, a subset of conserved stress-responsive genes was commonly regulated across treatments. Approximately 5% of differentially expressed genes also displayed differential methylation patterns, suggesting a coordinated role for DNA methylation in regulating gene expression. Motif enrichment analysis of differentially methylated regions revealed binding sites of key transcription factor families, including ERF, bHLH, and ABF, highlighting potential role for methylation in modulating transcription factor targeting. Furthermore, we identified stress-inducible molecular markers with potential applications in early stress detection and functional dissection of gene regulatory pathways. Together, these findings provide new insights into the coordinated genetic and epigenetic responses to abiotic stress and provide a foundation for developing biosensors and breeding strategies to enhance stress resilience woody plants.

CBI↗
NASA NTRS1997

Pulsatile Fluid Shear in Bone Remodeling

The objective of this investigation was to elucidate the sensitivity to transients in fluid shear stress in bone remodeling. Bone remodeling is clearly a function of the local mechanical environment which includes interstitial fluid flow. Traditionally, load-induced remodeling has been associated with low frequency (1-2 Hz) signals attributed to normal locomotion. McLeod and Rubin, however, demonstrated in vivo remodeling events associated with high frequency (15-30 Hz) loading. Likewise, other in vivo studies demonstrated that slowly applied strains did not trigger remodeling events. We therefore hypothesized that the mechanosensitive pathways which control bone maintenance and remodeling are differentially sensitive to varying rates of applied fluid shear stress.

Frangos, John A.↗
NASA NTRSDate not supplied

A Dominant Arabidopsis Thaliana ACTIN7 Mutant for Studies of Cytoskeletal-Mediated Root Gravity and Spaceflight Stress Responses

A forward genetic screen for Arabidopsis thaliana mutants that exhibited differential sensitivity to the actin-disrupting compound, latrunculin B (LatB), was conducted to uncover new players involved in actin-mediated root gravity responses. This to the isolation of a mutant that exhibited robust primary root growth at 100 nM LatB, which is a concentration that severely inhibits wild-type root elongation. Phenotypic analysis revealed that hypocotyl elongation in the dark and root hair tip growth in the mutant could tolerate LatB concentrations that impaired these processes in wild type. A cross between the mutant and wild type resulted in progeny resistance to LatB, which indicated that the mutant is dominant (hereafter referred to as LBR1 for LatB Resistant1). Filamentous-actin (F-actin) organization in LBR1 primary roots remained intact at 100 nM LatB, while that of wild type exhibited fragmented F-actin. Next generation sequencing revealed that LBR1 had a single nucleotide polymorphism (SNP) in the AT5G09810 gene that changed cytosine to a thiamine at the first exon. AT5G09810 encodes ACTIN7 (ACT7), which is one of three vegetative actin isoforms in A. thaliana. The SNP in the ACT7 gene led to a change in a single amino acid from proline at position 32 to a serine. Transgenic complementation of LBR1 plants with wild-type ACT7 under the control of the ACT7 promoter (pACT7:ACT7) and wild-type plants with LBR1, which contained the proline to serine mutation, also under the ACT7 promoter (pACT7:LBR1) confirmed that LBR1 is ACT7. The pACT7:LBR1 construct was also able to confer LatB resistance to the act7-5 and act2-3 vegetative ACT mutants. Moreover, LBR1 exhibited partial tolerance to salt and low phosphate, and enhanced root skewing on a clinostat, suggesting that site-directed engineering of vegetative ACT presents a strategy for generating stress-tolerant plants for spaceflight applications and studies of actin-mediated gravity responses.

Plant Space Biology↗
NASA NTRSDate not supplied

A Dominant Arabidopsis Thaliana ACTIN7 Mutant for Studies of Cytoskeletal-Mediated Root Gravity and Spaceflight Stress Responses

A forward genetic screen for Arabidopsis thaliana mutants that exhibited differential sensitivity to the actin-disrupting compound, latrunculin B (LatB), was conducted to uncover new players involved in actin-mediated root gravity responses. This led to the isolation of a mutant that exhibited robust primary root growth at 100 nM LatB, which is a concentration that severely inhibits wild-type root elongation. Phenotypic analysis revealed that hypocotyl elongation in the dark and root hair tip growth in the mutant could tolerate LatB concentrations that impaired these processes in wild type. A cross between the mutant and wild type resulted in progeny resistance to LatB, which indicated that the mutant is dominant (hereafter referred to as LBR1 for LatB Resistant1). Filamentous-actin (F-actin) organization in LBR1 primary roots remained intact at 100 nM LatB, while that of wild type exhibited fragmented F-actin. Next generation sequencing revealed that LBR1 had a single nucleotide polymorphism (SNP) in the AT5G09810 gene that changed cytosine to a thiamine at the first exon. AT5G09810 encodes ACTIN7 (ACT7), which is one of three vegetative actin isoforms in A. thaliana. The SNP in the ACT7 gene led to a change in a single amino acid from proline at position 32 to a serine. Transgenic complementation of LBR1 plants with wild-type ACT7 under the control of the ACT7 promoter (pACT7:ACT7) and wild-type plants with LBR1, which contained the proline to serine mutation, also under the ACT7 promoter (pACT7:LBR1) confirmed that LBR1 is ACT7. The pACT7:LBR1 construct was also able to confer LatB resistance to the act7-5 and act2-3 vegetative ACT mutants. Moreover, LBR1 exhibited partial tolerance to salt and low phosphate, and enhanced root skewing on a clinostat, suggesting that site-directed engineering of vegetative ACT presents a strategy for generating stress-tolerant plants for spaceflight applications and studies of actin-mediated gravity responses.

Plant Space Biology↗
NASA NTRS1946

The Lagrangian multiplier method of finding upper and lower limits to critical stresses of clamped plates

The theory of Lagrangian multipliers is applied to the problem of finding both upper and lower limits to the true compressive buckling stress of a clamped rectangular plate. The upper and lower limits thus bracket the true stress, which cannot be exactly found by the differential-equation approach. The procedure for obtaining the upper limit, which is believed to be new, presents certain advantages over the classical Rayleigh-Ritz method of finding upper limits. The theory of the lower-limit procedure has been given by Trefftz, but, in the present application, the method differs from that of Trefftz in a way that makes it inherently more quickly convergent. It is expected that in other buckling problems and in some vibration problems the Lagrangian multiplier method of finding upper and lower limits may be advantageously applied to the calculation of buckling stresses and natural frequencies.

Budiansky, Bernard↗
NASA NTRS1992

On the strength of oceanic fracture zones and their influence on the intraplate stress field

We use the locations and source mechanisms of oceanic intraplate earthquakes to test the hypothesis that the strength of oceanic fracture zones is less than that of normal oceanic lithosphere. The 77 earthquakes selected for the study have well-determined focal mechanisms and epicenters in regions where fracture zones are well mapped. We have search for dependence of faulting style, fault orientation, or principal stress direction on the distance from the nearest fracture zone. If fracture zones were generally weaker than the surrounding lithosphere, one of the principal horizontal stresses would be oriented nearly perpendicular to the fracture zone; we find no evidence that principal stresses near fracture zones are oriented preferentially in this manner. There is a slight tendency for earthquakes to occur near fracture zones, and patterns of fault orientation and sense of slip support the view that differential cooling and horizontal contraction on fracture zones may contribute seismogenic stress.

Bergman, Eric A.↗