Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “diesel combustion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Practical low-temperature gasoline combustion for very high efficiency off-road, medium- and heavy-duty engines

Low-temperature gasoline combustion (LTGC) with additive-mixing fuel injection (AMFI) is a new combustion strategy that has been demonstrated to deliver 9%–25% better brake thermal efficiency than similar-sized market-leading diesel engines over the operating map. Moreover, the LTGC-AMFI engine shows near-zero smoke, and NOx emissions are 4–100 times lower than those of a diesel, sufficiently low that no aftertreatment, or only passive NOx aftertreatment, would be sufficient (diesel exhaust fluid is not required). LTGC-AMFI combustion is based on kinetically controlled compression ignition of a dilute charge with a variable amount of low-to-moderate fuel stratification. Fast combustion control is provided by adding minute amounts of an ignition-enhancing additive into the fuel each engine cycle to control its reactivity. This strategy was used to operate a medium-duty (MD) LTGC-AMFI engine at loads from idle to 16.3 bar BMEP and speeds from 600 to 2400 rpm with regular E10 gasoline, which covers nearly the entire operating map of a typical MD engine. Turbine-out temperatures were sufficient for an oxidation catalyst to control hydrocarbon and CO emissions. Autonomie simulations over the GEM ARB Transient and the GEM 55 mph Cruise driving cycles for class-6 trucks using this technology showed fuel economies of 8.1 and 11.4 mpg-gasoline-equivalent, respectively, corresponding to 18.6% and 13.4% improvements over a similar-size diesel engine. Engine-out NOx emissions were 0.024 and 0.01 g/bhp-h, respectively, well below current U.S. emission standards. These results show that switching from diesel to LTGC-AMFI engines would greatly reduce greenhouse gas (GHG) emissions for off-road, MD and HD applications, which will continue to rely on combustion engines because electrification is not practical in the foreseeable future. Finally, with their reduced fuel consumption, the lower cost of gasoline compared to diesel fuel, and much lower aftertreatment costs, LTGC-AMFI engines also offer a significantly lower total cost of ownership.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Investigating the potential of a higher reactivity fuel to achieve faster heat-up of aftertreatment systems

Shortening the aftertreatment system heat-up period will be crucial to meet upcoming emissions regulations, which mandate significant reductions in tail-pipe emissions for on-road heavy-duty vehicles. This work studies the impact of increasing fuel reactivity on the combustion of post injections during the expansion stroke. The work demonstrates an operating strategy using a blend of di-butyl ether (a potential low-carbon biofuel component) and #2 diesel that achieves higher exhaust enthalpy, while maintaining similar engine-out emissions (NOx and combustion efficiency) in comparison to the baseline #2 diesel fuel (cetane number 41). On average, a 12% increase in exhaust enthalpy was observed for the blend (cetane number 60) relative to the baseline fuel. The ability to operate the higher reactivity fuel at a more retarded post-injection timing, where combustion with #2 diesel was found to be more unstable, and less complete was key to achieving higher exhaust enthalpy. However, a small fuel penalty (3%–5%) was also associated with the higher reactivity fuel with this operating strategy. The formation of fuel lean regions, due to the long ignition delays at late injection conditions, was predicted to be the leading contributor to the increased emissions of products of partial combustion. Here, chemical kinetic simulations using surrogates for the fuels used in the experiments, demonstrated the ability of a higher cetane fuel to outperform the baseline fuel under fuel lean conditions with equivalence ratios less than 0.7.

09 BIOMASS FUELS↗
DOE OSTI2023

Modeling the impact of the fuel injection strategy on the combustion and performance characteristics of a heavy-duty GCI engine

Gasoline compression ignition (GCI) is a promising strategy to achieve high thermal efficiency and low emissions with limited modifications to the conventional diesel engine hardware. It is a partially premixed concept, which derives its superiority from higher volatility and longer ignition delay of gasoline-like fuels combined with higher compression ratio typical of diesel engines. Here, the present study investigates the combustion process in a GCI engine operating with different injection strategies using computational fluid dynamics (CFD). Simulations are carried out on a single cylinder of a multi cylinder heavy-duty compression ignition engine, which operates at a compression ratio of 17:1 and an engine speed of 1038 rev/min. Two different injection strategies viz., late injection (LI), and early pilot injection (EP) are investigated to understand their impact on combustion and performance of the engine. Renormalized group (RNG) k-ε model is used to describe in-cylinder turbulence and KH RT model is used to simulate the fuel spray breakup. The developed CFD methodology is validated against relevant experimental data under a wide range of operating conditions for each injection strategy. The developed CFD methodology was found to capture the engine combustion behavior quite well. Based on the validated CFD model, the differences in the progress of combustion event for the two injection strategies is highlighted. It was found that a larger pilot fuel mass fraction results in a steeper rise in the initial heat release rate which in turn influences the transition to mixing controlled combustion. In line with the experimental data, the study showed that the late pilot injection strategy with three injection pulses, results in higher performance compared to the other conditions.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Superior performance biodiesel from biomass-derived fusel alcohols and low grade oils: Fatty acid fusel esters (FAFE)

We demonstrated production of a superior performance biodiesel referred to here as fatty acid fusel alcohol esters (FAFE) – by reacting fusel alcohols (isobutanol, 3-methyl-1-butanol, and (S)-(-)-2-methyl-1-butanol) with oil (glyceryl trioleate) using lipase from Aspergillus oryzae. Reaction conditions corresponding to a molar ratio of 5:1 (fusel alcohols to oil), enzyme loading of 2% w/w, reaction temperature of 35 °C, shaking speed of 250 rpm, and reaction time of 24 h achieved >97% conversion to FAFE. Further, FAFE obtained from reacting a fusel alcohol mixture with corn oil were evaluated for use as a fuel for diesel engines. FAFE mixtures showed superior combustion and cold-flow properties, with the derived cetane numbers up to 4.8 points higher, cloud points up to -6 °C lower, and the heat of combustion up to 2.1% higher than the corresponding FAME samples, depending on the fusel mixture used. This represents a significant improvement for all three metrics, which are typically anti-correlated. Finally, FAFE provides a new opportunity for expanded usage of biodiesel by addressing feedstock limitations, fuel performance, and low temperature tolerance.

09 BIOMASS FUELS↗
DOE OSTI2023

An Analysis of the Potential and Cost of the U.S. Refinery Sector Decarbonization

In 2019, U.S. petroleum refineries emitted 196 million metric tons (MT) of CO 2 , while the well-to-gate and the full life cycle CO 2 emissions were significantly higher, reaching 419 and 2843 million MT of CO 2 , respectively. This analysis examines decarbonization opportunities for U.S. refineries and the cost to achieve both refinery level and complete life-cycle CO 2 emission reductions. Here, we used 2019 life-cycle CO 2 emissions from U.S. refineries as a baseline and identified three categories of decarbonization opportunity: (1) switching refinery energy inputs from fossil to renewable sources (e.g., switch hydrogen source); (2) carbon capture and storage of CO 2 from various refining units; and (3) changing the feedstock from petroleum crude to biocrude using various blending levels. While all three options can reduce CO 2 emissions from refineries, only the third can reduce emissions throughout the life cycle of refinery products, including the combustion of fuels (e.g., gasoline and diesel) during end use applications. A decarbonization approach that combines strategies 1, 2, and 3 can achieve negative life-cycle CO 2 emissions, with an average CO 2 avoidance cost of $\$113$ - $\$477$/MT CO 2 , or $\$54$ - $\$227$/bbl of processed crude; these costs are driven primarily by the high cost of biocrude feedstock.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
NASA NTRS1976

Alternative general-aircraft engines

The most promising alternative engine (or engines) for application to general aircraft in the post-1985 time period was defined, and the level of technology was cited to the point where confident development of a new engine can begin early in the 1980's. Low emissions, multifuel capability, and fuel economy were emphasized. Six alternative propulsion concepts were considered to be viable candidates for future general-aircraft application: the advanced spark-ignition piston, rotary combustion, two- and four-stroke diesel, Stirling, and gas turbine engines.

Tomazic, W. A.↗
NASA NTRS1981

Gasification of carbon fiber composites for the alleviation of electrical hazards

A mixture of calcium acetate and lithium acetate applied to the surface of carbon fibers caused the fibers to gasify in a simulated airplane-crash fire. Tests conducted with a JPL-developed electrical detector showed the catalyst-modified composites to release few fibers during burning, while state-of-the-art composites released several hundred. Mechanical property tests demonstrated nearly identical behavior of catalyst-modified and state-of-the-art composites. Aging tests also showed little difference in the composite strength except for a severe reduction when soaked in water. Several promising new concepts resulted from the project, including catalytic elimination of carbon particulates from diesel exhaust, catalytic improvement of coal combustion, and electrical destruction of carbon particulates in combustion systems.

Hull, G.↗
NASA NTRS1990

Electrostatic Dispersion Of Drops In Clusters

Electrical charging speeds evaporation. Report presents theoretical study of evaporation and dispersion of electrostatically charged clusters of drops in liquid fuel sprays. Represents extension of studies described in article, "More About Evaporation of Drops in Clusters" (NPO-17594). Undertaken in effort to learn how electrostatic atomization used to disperse fuel better in order to reduce formation of soot in diesel engines and other power and combustion systems.

Bellan, Josette↗
NASA NTRS1999

Lightweight Exhaust Manifold and Exhaust Pipe Ducting for Internal Combustion Engines

An improved exhaust system for an internal combustion gasoline-and/or diesel-fueled engine includes an engine exhaust manifold which has been fabricated from carbon- carbon composite materials in operative association with an exhaust pipe ducting which has been fabricated from carbon-carbon composite materials. When compared to conventional steel. cast iron. or ceramic-lined iron paris. the use of carbon-carbon composite exhaust-gas manifolds and exhaust pipe ducting reduces the overall weight of the engine. which allows for improved acceleration and fuel efficiency: permits operation at higher temperatures without a loss of strength: reduces the "through-the wall" heat loss, which increases engine cycle and turbocharger efficiency and ensures faster "light-off" of catalytic converters: and, with an optional thermal reactor, reduces emission of major pollutants, i.e. hydrocarbons and carbon monoxide.

Northam, G. Burton↗
DOE OSTI2022

Influence of NOx chemistry on the prediction of natural gas end-gas autoignition in CFD engine simulations

Natural gas (NG) represents a promising low-cost/low-emission alternative to diesel fuel when used in high-efficiency internal combustion engines. Advanced combustion strategies utilizing high EGR rates and controlled end-gas autoignition can be implemented with NG to achieve diesel-like efficiencies; however, to support the design of these next-generation NG ICEs, computational tools, including single- and multi-dimensional simulation packages will need to account for the complex chemistry that can occur between the reactive species found in EGR (including NOx) and the fuel. Research has shown that NOx plays an important role in the promotion/inhibition of large hydrocarbon autoignition and when accounted for in CFD engine simulations, can significantly improve the prediction of end-gas autoignition for these fuels. However, reduced NOx-enabled NG mechanisms for use in CFD engine simulations are lacking, and as a result, the influence of NOx chemistry on NG engine operation remains unknown. Here, we analyze the effects of NOx chemistry on the prediction of NG/oxidizer/EGR autoignition and generate a reduced mechanism of a suitable size to be used in engine simulations. Results indicate that NG ignition is sensitive to NOx chemistry, where it was observed that the addition of EGR, which included NOx, promoted NG autoignition. The modified mechanism captured well all trends and closely matched experimentally measured ignition delay times for a wide range of EGR rates and NG compositions. Here, the importance of C2-C3 chemistry is noted, especially for wet NG compositions containing high fractions of ethane and propane. Finally, when utilized in CFD simulations of a Cooperative Fuels Research (CFR) engine, the new reduced mechanism was able to predict the knock onset crank angle (KOCA) to within one crank angle degree of experimental data, a significant improvement compared to previous simulations without NOx chemistry.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Numerical investigation of a fueled pre-chamber spark-ignition natural gas engine

Pre-chamber spark-ignition (PCSI) is a leading advanced ignition concept for internal combustion engines with the potential to enable diesel-like efficiency in medium-duty/heavy-duty (MD/HD) natural gas (NG) engines. By leveraging distributed ignition sources from multiple turbulent jets, the PCSI technology can deliver extremely short combustion duration in ultra-lean mixtures and significantly improve the engine thermal efficiency. However, in the automotive industry there is a lack of adequate science base and predictive simulation tools required for commercial development of PCSI engines. Here, in this study, Reynolds-Average Navier-Stokes simulations are carried out to describe the combustion process in lean-burn NG engines, focusing on the combustion modeling approach. Two combustion models, multi-zone well-stirred reactor (MZ-WSR) and G-equation, are used to simulate the combustion process in an MD NG engine equipped with a fueled-PCSI system for four operating conditions close to the lean operating limit. A skeletal chemical mechanism and a laminar flame speed tabulation are used to compute the combustion accurately. Simulation results are compared with experimental data regarding measured cylinder pressure, heat release rate, and combustion duration. By dividing the PCSI combustion process into four distinct phases, the difference between the two models’ results for each phase is analyzed in detail. The MZ-WSR model overestimates the combustion duration for early flame kernel growth in the pre-chamber due to the lack of a specific formulation to take turbulence-chemistry interaction into account. Despite the prolonged combustion duration and low pressure built-up inside the pre-chamber, the model matches the combustion rate in the main-chamber. In contrast, the G-equation model delivers good agreements for the pre-chamber combustion and turbulent jet-driven combustion processes. However, the model starts to underestimate the combustion rate in the main-chamber, especially under ultra-lean mixture conditions. Finally, improvements are needed for both models to simulate the later combustion stage that occurred in the near-wall regions.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

An experimental and chemical kinetic modeling study of 4-butoxyheptane combustion

Here, the combustion kinetics of a novel oxygenated bioblendstock for diesel, 4-butoxyheptane (4-BH), was investigated experimentally using a flow reactor and a heated, high-pressure shock tube. The flow reactor experiments employed oxygen as the oxidizer and helium as the diluent with oxidation conducted at atmospheric pressure and 10 bar for temperatures from 400 to 1000 K at 20-K intervals. The fuel, oxidizer, and diluent flow rates were varied at different temperatures to maintain a constant initial fuel mole fraction of 1000 ppm, with stoichiometric equivalence ratio, and a residence time of 2.0 s. The reacted gas was fed to two separate GC systems that could qualitatively and quantitatively detect product species. Additionally, real fuel-air ignition delay time (IDT) data were collected using a heated, high-pressure shock-tube facility. Fuel lean (φ = 0.5) and stoichiometric (φ = 1.0) mixtures were investigated at 10 atm as well as at 30 atm for the fuel lean case for temperatures between 847 and 1259 K. A detailed chemical kinetics mechanism was developed to model the product distribution from the flow reactor and IDTs from the shock tube. The proposed model was able to predict the double NTC behavior in flow reactor experiments reasonably well. Model predictions at low temperatures were observed to be highly sensitive to the rate constants of ketohydroperoxide (KHP) decomposition in the case of the OOH group in α position which were modeled based on existing literature studies on ethers. It was noted that in the absence of theoretical or experimental studies, the rate constants for KHP decomposition used in the literature were empirically set. Additional studies are required to address the gap in model prediction obtained in this study and to reduce the uncertainty in kinetics models for ether oxidation. Predicted product concentrations and IDTs showed some quantitative agreement with experimental data, but the overall reactivity of the IDTs is underpredicted. Additionally, significant deviation is observed for the IDT results at 10 atm for the stoichiometric case with minor deviations for the other cases. The reaction pathways to the missing products were then further analyzed theoretically through quantum-mechanical calculations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Development of a Turbulent Liquid Spray Atomization Model for Diesel Engine Simulations (Final Technical Report)

This project addresses the systematic lack of predictive capabilities by spray models within engine CFD codes. We develop a new modeling approach to predict the breakup of diesel sprays based on recent literature showing that liquid turbulence plays a fundamental role in spray atomization. A new body of quantitative validation data is also developed as a critical element of the project, leveraging the joint capabilities of Georgia Tech’s high-pressure continuous-flow spray chamber and Argonne National Lab’s near-nozzle x-ray diagnostics at the Advanced Photon Source. This project contributes spatially-resolved measurements of drop size distribution within well-characterized diesel injectors, Spray A and D, from the Engine Combustion Network (ECN) to the engine combustion community for the first time. Utilizing this new body of measurements, we validate and demonstrate a new spray model for diesel sprays, termed the KH-Faeth model, that predicts global and local spray characteristic more accurately than the widely adopted and employed KH model. Predicted drop size distributions are seen to predict measured drops sizes both quantitatively and predictively, with accurate response in droplet size distributions over a wide range of ambient density, injection pressure, and injector nozzle size (Spray A and D) without model tuning. The KH-Faeth model can reduce error in the predicted centerline droplet size profile by up to 80% for ECN Spray D simulations when compared to use of the widely employed KH model.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Evaluation of methods for characterizing the fine particulate matter emissions from aircraft and other diffusion flame combustion aerosol sources

The U. S. Environmental Protection Agency in collaboration with the U. S. Air Force Arnold Engineering Development Complex conducted the VAriable Response In Aircraft nvPM Testing (VARIAnT) 3 and 4 test campaigns to compare nvPM emissions measurements from a variety of diffusion flame combustion aerosol sources (DFCASs), including a Cummins diesel engine, a diesel powered generator, two gas turbine start carts, a J85-GE-5 turbojet engine burning multiple fuels, and a Mini-CAST soot generator. The VARIAnT research program has conducted four test campaigns to date with the VARIAnT 3 and 4 test campaigns focusing on BC mass instrument performance, use of gas turbine engine sources for BC mass instrument calibration, and the characterization of the aerosols produced from the combustion sources. Results from both campaigns revealed agreement of about 20% between the AVL Micro-Soot Sensor, the Cavity Attenuated Phase Shift (CAPS PMSSA) monitor and the thermal-optical reference method for elemental carbon (EC), independent of the calibration source used. For the Artium LII-300, the measured mass concentrations in VARIAnT3 fall within 18% and in VARIAnT4 fall within 32% of the reference EC mass concentration when calibrated on a combustor rig in VARIAnT3 and on a LGT-60 start cart in VARIAnT4, respectively. It was also found that the three mass instrument types (MSS, CAPS PMSSA, and LII-300) can exhibit different BC to reference EC ratios depending on the emission source that appear to correlate to particle geometric mean mobility diameter, morphology, or some other parameter associated with particle geometric mean diameter (GMD) with the LII-300 showing a slightly stronger apparent trend with GMD. Systematic differences in LII-300 measured mass concentrations have been reduced by calibrating with a turbine combustion source (combustor or turbine engine). With respect to the particle size measurements made, the sizing instruments (TSI SMPS, TSI EEPS, and Cambustion DMS 500) were found to be in general agreement in terms of size distributions and concentrations with some exceptions. Teflon filter measurements of the total aerosol mass produced by the various DFCASs differed from the reference EC, BC, and integrated particle sized distribution measured aerosol masses. The Teflon filter measured mass was 30 to 40% greater than the reference EC and 50 to 60% greater than the BC mass for the J85 in both test campaigns. The measurements of particle size distributions and single particle analysis by miniSPLAT indicated the presence of large particles (>100 nm) having more compact morphologies, higher effective density, and a composition dominated by OC and ash. This increased large particle fraction is also associated with higher values of single scattering albedo measured by the CAPS PMSSA instrument and higher OC/EC measurements. These measurements indicate gas turbine engine emissions can be a more heterogeneous mix of particle types beyond the original E31 assumption that it is mainly composed of black carbon.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS1941

Researches on direct injection in internal-combustion engines

These researches present a solution for reducing the fatigue of the Diesel engine by permitting the preservation of its components and, at the same time, raising its specific horsepower to a par with that of carburetor engines, while maintaining for the Diesel engine its perogative of burning heavy fuel under optimum economical conditions. The feeding of Diesel engines by injection pumps actuated by engine compression achieves the required high speeds of injection readily and permits rigorous control of the combustible charge introduced into each cylinder and of the peak pressure in the resultant cycle.

Tuscher, Jean E↗
NASA NTRS1980

Durability testing at 5 atmospheres of advanced catalysts and catalyst supports for gas turbine engine combustors

The durability of CATCOM catalysts and catalyst supports was experimentally demonstrated in a combustion environment under simulated gas turbine engine combustor operating conditions. A test of 1000 hours duration was completed with one catalyst using no. 2 diesel fuel and operating at catalytically-supported thermal combustion conditions. The performance of the catalyst was determined by monitoring emissions throughout the test, and by examining the physical condition of the catalyst core at the conclusion of the test. Tests were performed periodically to determine changes in catalytic activity of the catalyst core. Detailed parametric studies were also run at the beginning and end of the durability test, using no. 2 fuel oil. Initial and final emissions for the 1000 hours test respectively were: unburned hydrocarbons (C3 vppm):0, 146, carbon monoxide (vppm):30, 2420; nitrogen oxides (vppm):5.7, 5.6.

Olson, B. A.↗
DOE OSTI2020

Supercritical Reforming of Wet Ethanol for High Efficiency Direct-injection Heavy-duty Compression-ignition Engines

The purpose of the research was to investigate the potential of using a mature bio-fuel in heavy-duty compression ignition engines. By co-optimizing both the fuel characteristics and engine system the potential for a superior outcome was demonstrated. The use of wet bio-ethanol eliminates the majority of the energy intensive distilling and dehydrating fuel production processes, which moves the fuel towards carbon neutral and also lowers the fuel costs. The relatively high water content of the resulting fuel is leveraged in the proposed novel combustion system by incorporating an integrated high efficiency exhaust waste heat recovery system. This results in significantly higher thermal efficiency. In addition the combustion system features low criteria pollutant emissions and the potential to reduce the initial cost of the engine system hardware. Substantial societal benefits are demonstrated through the co-optimization of the fuel and engine system. A computational proof-of-concept study has been performed to demonstrate the potential benefits of a novel wet ethanol heavy-duty compression ignition combustion system featuring integrated exhaust waste heat recovery. A combined in-cylinder closed cycle 3D computational fluid dynamics (CFD) - 1D engine system simulation approach was used. The models were validated to baseline engine data using diesel fuel and then applied to the wet ethanol study. The original concept was to maximize exhaust waste heat recovery through supercritical reforming of the wet ethanol fuel. Phase I simulation results indicated that the optimal solution for maximum engine efficiency gains were realized through maximizing thermo-mechanical recuperation with negligible fuel reformation. The results show the potential to achieve impressive gains in brake thermal efficiency (BTE) over the base diesel engine. The potential to increase BTE up to 20.9% over the base diesel engine was demonstrated, with even larger gains possible through reduced in-cylinder heat transfer losses. The majority of the efficiency gains were realized through integrated high efficiency exhaust waste heat recovery. The concept also has the potential to achieve future ultra-low NO x emissions standards and negligible engine-out soot emissions. The mixing controlled combustion of high temperature wet ethanol features relatively low engine-out NO x emissions without the need for exhaust gas recirculation (EGR). The soot free combustion enabled by the relatively high oxygen content of ethanol also allows for the use of stoichiometric mixing controlled combustion, which is not practical with diesel fuel. When stoichiometric combustion is used a simple passive 3-way catalyst can be used for exhaust emissions after-treatment and near zero tailpipe emissions. The Phase I simulations results have defined the system layout and requirements in preparation for the Phase II experimental proof-of-concept study. The potential applications of the research include most current applications of diesel engines. The Phase I study focused on heavy-duty on-highway class 8 trucks. However, virtually any application that requires highly efficient clean power generation would benefit from the novel engine system proposed. The results indicate substantial fuel cost savings and reduced greenhouse gas emissions with similar or reduced initial system hardware costs compared to modern diesel engine systems.

09 BIOMASS FUELS↗