Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “dielectric”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Dielectric and magnetic properties of microwave-absorbing FeAl x O y catalysts fabricated via solution combustion synthesis

Iron-based alumina (FeAl x O y ) nanocomposites are microwave-absorbers and catalysts, which makes them promising for emerging microwave-assisted thermocatalytic technologies. Solution combustion synthesis (SCS) has been used to synthesize FeAl x O y powders, and prior work has demonstrated that adjusting SCS parameters significantly changes phase composition and specific surface area of the products. However, it is unclear how synthesis parameters affect their microwave-absorbing properties, which are essential for optimizing microwave-assisted technologies. To address this challenge, in the present work, twelve different FeAl x O y products were synthesized at different combinations of the SCS parameters such as two fuels (citric acid and glycine), two heating modes (hotplate and muffle furnace), and three Fe:Al molar ratios (2:1, 1:1, 1:2). Dielectric and magnetic properties of the products were characterized using a network analyzer and a vibrating sample magnetometer. Based on the measured permittivity and permeability, penetration depth and reflection loss were calculated as a function of frequency and bed thickness. The products were heated by microwaves at 2.45 GHz and then examined with X-ray diffraction (XRD) analysis. For all products, the magnetic saturation was lower than for bulk iron oxides because of the small crystallite size and aluminum substitution. The use of glycine induced high dielectric losses and enabled fast microwave-heating rates compared to citric acid. Higher Fe:Al ratio also led to higher dielectric and magnetic losses. With glycine fuel, SCS in a furnace induced larger penetration depth and lower microwave absorption than SCS on a hotplate. The minimization of reflected power was more sensitive to the thickness of the product bed than to the frequency of the electromagnetic field. Post-heating XRD analysis revealed different phase transformations in the FeAl x O y powders depending on the SCS parameters. As a result, an FeAl x O y material, synthesized via incipient wetness impregnation, lacked magnetic losses and did not heat well as compared to the SCS products.

Combustion synthesis↗
DOE OSTI2020

Effects of Ion Size and Dielectric Constant on Ion Transport and Transference Number in Polymer Electrolytes

Salt-doped polymers without added solvents have potential as nonflammable, robust electrolytes for batteries but suffer from low ion conductivity. Using bulky anions with delocalized charge may reduce ion agglomeration and increase conduction. However, size asymmetry between ions may increase preferential solvation of cations versus the larger anions, lowering the transference number t + (fraction of conductivity contributed by the cation, relevant to battery performance). We use coarse-grained molecular dynamics simulations, including a 1/r 4 potential to capture size-dependent solvation effects, to relate polymer and ion chemistry to t + and overall conductivity. At low ion size disparity, increasing dielectric constant improves cation conduction due to the mitigation of ion aggregation and correlated cation-anion motion. However, at high ion size disparity, high dielectric medium results in strong preferential solvation of cations, reducing cation mobility and t + . The trade-off between better cation-anion separation and cation preferential solvation suggests that the strategy of developing high dielectric polymers may enhance performance only at low ion size disparity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Dielectric screening in perovskite photovoltaics

Abstract The performance of perovskite photovoltaics is fundamentally impeded by the presence of undesirable defects that contribute to non-radiative losses within the devices. Although mitigating these losses has been extensively reported by numerous passivation strategies, a detailed understanding of loss origins within the devices remains elusive. Here, we demonstrate that the defect capturing probability estimated by the capture cross-section is decreased by varying the dielectric response, producing the dielectric screening effect in the perovskite. The resulting perovskites also show reduced surface recombination and a weaker electron-phonon coupling. All of these boost the power conversion efficiency to 22.3% for an inverted perovskite photovoltaic device with a high open-circuit voltage of 1.25 V and a low voltage deficit of 0.37 V (a bandgap ~1.62 eV). Our results provide not only an in-depth understanding of the carrier capture processes in perovskites, but also a promising pathway for realizing highly efficient devices via dielectric regulation.

14 SOLAR ENERGY↗
DOE OSTI2023

Ultrathin quasi-2D amorphous carbon dielectric prepared from solution precursor for nanoelectronics

Abstract Materials keeping thickness in atomic scale but extending primarily in lateral dimensions offer properties attractive for many emerging applications. However, compared to crystalline counterparts, synthesis of atomically thin films in the highly disordered amorphous form, which avoids nonuniformity and defects associated with grain boundaries, is challenging due to their metastable nature. Here we present a scalable and solution-based strategy to prepare large-area, freestanding quasi-2D amorphous carbon nanomembranes with predominant sp 2 bonding and thickness down to 1–2 atomic layers, from coal-derived carbon dots as precursors. These atomically thin amorphous carbon films are mechanically strong with modulus of 400 ± 100 GPa and demonstrate robust dielectric properties with high dielectric strength above 20 MV cm −1 and low leakage current density below 10 −4 A cm −2 through a scaled thickness of three-atomic layers. They can be implemented as solution-deposited ultrathin gate dielectrics in transistors or ion-transport media in memristors, enabling exceptional device performance and spatiotemporal uniformity.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2025

Dielectric constant engineering of nonfullerene acceptors enables a record fill factor of 83.58% and a high efficiency of 20.80% in organic solar cells

Organic solar cells (OSCs) have achieved power conversion efficiencies (PCEs) surpassing 20%, but their development remains hindered by the inherently low dielectric constant (εr) of organic semiconductors, which limits charge transport and contributes to serious recombination losses. Herein, we present a comprehensive strategy to overcome the challenge by engineering the dielectric properties of nonfullerene acceptors (NFAs). Two Y-series NFAs of BTP-N3F and BTP-C3F have been synthesized featuring trifluoromethyl (CF 3 ) end-capped alkyl side chains. This molecular design significantly enhances the dipole moment and ε r (up to ∼5.9) when compared to the reference acceptor Y6 (∼3), reducing the exciton binding energy (E b ) and improving charge transport. Furthermore, the incorporation of a high-εr polymer additive, poly(pentafluorostyrene) (PPFS), synergistically improves the active layer morphology and dielectric properties, enabling efficient charge extraction and reduced recombination losses. Devices based on the optimized D18-Cl/BTP-C3F system have achieved a record-high fill factor (FF) of 83.58% and an impressive PCE of 20.80%, setting a new benchmark for OSCs. Finally, our results underscore the pivotal role of ε r in enhancing device performance and establish a versatile pathway for advancing OSC efficiency and stability through molecular and morphological optimization.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Simultaneous mapping of nanoscale dielectric, electrochemical, and ferroelectric surface properties of van der Waals layered ferroelectric via advanced SPM

Ferroelectric surfaces involve a complex interplay between polarization and dielectric properties, internal and external surface charge screening, and ionic and electrochemical effects. There is currently no good way to simultaneously capture all the required information at appropriate length scales. To this end, we present an advanced scanning probe microscopy approach for simultaneously mapping surface potential, dielectric, and piezoelectric properties on the nanoscale. For quantitatively mapping electromechancial properties, we utilize interferometric displacement sensing piezoresponse force microscopy, which measures the effective piezoelectric coefficient free of background artifacts such as the cantilever body electrostatics. The dielectric and surface electrochemical properties are captured during G-mode electrostatic force microscopy/Kelvin probe force microscopy operated in the lift mode. We show the capabilities of this approach on the chemically phase separated composite sample consisting of a van der Waals layered ferroelectric CuInP 2 S 6 phase and a non-polar In 4/3 P 2 S 6 phase. Finally, we demonstrate domain structure evolution during thermally stimulated phase transition.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Non-local dielectric effects in nanoscience

Here, the physical properties of charges and excitations in nanoscale materials are influenced both by the dielectric properties of the material itself and the surrounding environment. This non-local dielectric effect was first discussed in the context of molecules in solvents over a century ago. In this perspective, we discuss non-local dielectric effects in zero-dimensional, one-dimensional, and two-dimensional nanoscale systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Reduced trap state density in AlGaN/GaN HEMTs with low-temperature CVD-grown BN gate dielectric

In this Letter, low-temperature (400 °C) chemical vapor deposition-grown boron nitride (BN) was investigated as the gate dielectric for AlGaN/GaN metal–insulator–semiconductor high electron mobility transistors (MISHEMTs) on a Si substrate. Comprehensive characterizations using x-ray photoelectron spectroscopy, reflection electron energy loss spectroscopy, atomic force microscope, high-resolution transmission electron microscopy, and time-of-flight secondary ion mass spectrometry were conducted to analyze the deposited BN dielectric. Compared with conventional Schottky-gate HEMTs, the MISHEMTs exhibited significantly enhanced performance with 3 orders of magnitude lower reverse gate leakage current, a lower off-state current of 1 × 10−7 mA/mm, a higher on/off current ratio of 108, and lower on-resistance of 5.40 Ω mm. The frequency-dependent conductance measurement was performed to analyze the BN/HEMT interface, unveiling a low interface trap state density (Dit) on the order of 5 × 1011–6 × 1011 cm−2 eV−1. This work shows the effectiveness of low-temperature BN dielectrics and their potential for advancing GaN MISHEMTs toward high-performance power and RF electronics applications.

Physics↗
DOE OSTI2026

Dielectric properties of neutron and proton irradiated polymeric nanocomposite insulation for superconducting magnets of fusion power plants

Studies on radiation-resistant electrical insulation for superconducting magnets of nuclear fusion power plants are discussed. Metal oxide nanoparticle-incorporated organic polymer composite (MONAP) insulation films were manufactured and studied for their dielectric breakdown strength after exposure to neutrons and proton radiation at varying levels. Samples with up to 5 wt% of nanoparticles (NPs) of SiO 2 , MgO, and ZrO 2 were studied. The samples were exposed to radiation of up to 2 × 10 16 neutrons/cm 2 and 200 Mrad of protons. The addition of the nanoparticles improved the radiation resistance of the MONAP, and the performance depended on the type of NPs and the radiation exposure. Dielectric breakdown measurements at 77 K showed little degradation. Enhancement of dielectric strength was observed in some instances.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Toward improved PVDF-BaTiO 3 composite dielectrics: mechanical activation of the filler versus filler content

Abstract Barium titanate (BT) perovskite particles were surface modified by means of mechanical treatment and used as inorganic component in polyvinylidene fluoride (PVDF) based composites. The changes in electrical properties of the composite films with increasing in filler content were followed by dielectric spectroscopy, breakdown strength andD-Emeasurements. A comparison of the properties of the composites prepared with untreated and mechanically activated particles revealed that there is a significant difference in their performances at low filler concentrations (<20 wt%). Introduction of the surface modified ceramic particles into PVDF matrix led to an increase of the dielectric constant without affecting significantly the electrical breakdown strength. In contrast, when as received BT particles were used a filler, both dielectric constants and breakdown strengths of the composite films were lower than the corresponding values observed for the pure PVDF. At higher concentrations, however, the influence of pre-treatment of the filler on the effective electrical properties becomes less significant. The obtained results were discussed in terms of the pronounced crystallization of polarβandγcrystal phases of PVDF in the presence of surface modified BT fillers, which is confirmed by Raman spectroscopy.

Physics↗
DOE OSTI2021

Simulating MADMAX in 3D: Requirements for Dielectric Axion Haloscopes

We present 3D calculations for dielectric haloscopes such as the currently envisioned MADMAX experiment. For ideal systems with perfectly flat, parallel and isotropic dielectric disks of finite diameter, we find that a geometrical form factor reduces the emitted power by up to 30% compared to earlier 1D calculations. We derive the emitted beam shape, which is important for antenna design. We show that realistic dark matter axion velocities of 10 -3 c and inhomogeneities of the external magnetic field at the scale of 10% have negligible impact on the sensitivity of MADMAX. We investigate design requirements for which the emitted power changes by less than 20% for a benchmark boost factor with a bandwidth of 50 MHz at 22 GHz, corresponding to an axion mass of 90 μeV. We find that the maximum allowed disk tilt is 100 μm divided by the disk diameter, the required disk planarity is 20 μm (min-to-max) or better, and the maximum allowed surface roughness is 100 μm (min-to-max). We show how using tiled dielectric disks glued together from multiple smaller patches can affect the beam shape and antenna coupling.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

Experimental determination of axion signal power of dish antennas and dielectric haloscopes using the reciprocity approach

The reciprocity approach is a powerful method to determine the expected signal power of axion haloscopes in a model-independent way. Especially for open and broadband setups like the MADMAX dielectric haloscope the sensitivity to the axion field is difficult to calibrate since they do not allow discrete eigenmode analysis and are optically too large to fully simulate. The central idea of the reciprocity approach is to measure a reflection-induced test field in the setup instead of trying to simulate the axion-induced field. In this article, the reciprocity approach is used to determine the expected signal power of a dish antenna and a minimal dielectric haloscope directly from measurements. The results match expectations from simulation but also include important systematic effects that are too difficult to simulate. In particular, the effect of antenna standing waves and higher order mode perturbations can be quantified for the first time in a dielectric haloscope.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Dyson maps and unitary evolution for Maxwell equations in tensor dielectric media

The propagation and scattering of electromagnetic waves in dielectric media is of theoretical and experimental interest in a wide variety of fields. An understanding of observational results generally requires a numerical solution of Maxwell equations—usually implemented on conventional computers using sophisticated numerical algorithms. In recent years, advances in quantum information science and in the development of quantum computers have piqued curiosity about taking advantage of these resources for an alternate numerical approach to Maxwell equations. This requires a reformulation of the classical Maxwell equations into a form suitable for quantum computers which, unlike conventional computers, are limited to unitary operations. In this paper, a unitary framework is developed for the propagation of electromagnetic waves in a spatially inhomogeneous, passive, nondispersive, and anisotropic dielectric medium. For such a medium, generally, the evolution operator in the combined Faraday-Ampere equations is not unitary. There are two steps needed to convert this equation into a unitary evolution equation. In the first step, a weighted Hilbert space is formulated in which the generator of dynamics is a pseudo-Hermitian operator. In the second step, a Dyson map is constructed which maps the weighted-physical-Hilbert space to the original Hilbert space. Furthermore, the resulting evolution equation for the electromagnetic wave fields is unitary. Utilizing the framework developed in these steps, a unitary evolution equation is derived for electromagnetic wave propagation in a uniaxial dielectric medium. The resulting form is suitable for quantum computing.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Impacts to FeRAM design arising from interfacial dielectric layers and wake up modulation in ferroelectric hafnium zirconium oxide

As ferroelectric hafnium zirconium oxide (HZO) becomes more widely utilized in ferroelectric microelectronics, integration impacts of intentional and non-intentional dielectric interfaces and their effects upon the ferroelectric film wake up and circuit parameters become important to understand. In this work, the effect of the addition of a linear dielectric aluminum oxide, Al 2 O 3 , below a ferroelectric Hf 0.58 Zr 0.42 O 2 film in a capacitor structure for FeRAM applications with NbN electrodes was measured. Depolarization fields resulting from the linear dielectric is observed to induce a reduction of the remanent polarization of the ferroelectric. Addition of the aluminum oxide also impacts the wake up of the HZO with respect to the cycling voltage applied. Intricately linked to the design of a FeRAM 1C/1T cell, the metal-ferroelectric-insulator-metal (MFIM) devices are observed to significantly shift charge related to the read states based on aluminum oxide thickness and wake up cycling voltage. As a result, a 33% reduction in the separation of read states is measured, which complicates how a memory cell is designed and illustrates the importance of clean interfaces in devices.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2026

Wafer-scale high-k SrTiO 3 dielectrics with rational barrier-layer design for low leakage and high charge density

High-k oxides such as SrTiO 3 promise large capacitance, but their dielectric response is often limited by leakage currents due to reduced bandgaps. We show that introducing a thin barrier layer beneath SrTiO 3 is a simple and effective way to suppress leakage and increase charge density. Using hybrid molecular beam epitaxy, we grew uniform SrTiO 3 films on Nb:SrTiO 3 , CaSnO 3 /Nb:SrTiO 3 , and 2-in. SiO 2 /p-Si stacks to directly compare how different barrier layers influence device behavior. Both CaSnO 3 and SiO 2 reduce leakage, but the ultra-wide-bandgap SiO 2 layer enables much higher operating voltages, yielding charge densities exceeding 5 × 10 13 cm −2 at room temperature—more than a fivefold enhancement compared to devices without a barrier layer. This improvement comes with a predictable trade-off: the lower dielectric constant of SiO 2 reduces overall capacitance, making its thickness an important design parameter. Together, these results demonstrate that rational barrier-layer engineering—including wafer-scale integration on Si—provides a clear pathway to achieving higher charge densities in SrTiO 3 -based dielectric devices.

36 MATERIALS SCIENCE↗
DOE OSTI2021

PyOECP: A flexible open-source software for the measurement and modeling of the dielectric spectrum from the reflection coefficient

We present PyOECP, a Python-based flexible open-source software for estimating and modeling the complex permittivity obtained from the open-ended coaxial probe (OECP) technique. The transformation of the measured reflection coefficient to complex permittivity is performed based on two different models, including the capacitance model and the antenna model. The software library contains dielectric spectra of common reference liquids, which can be used to transform the reflection coefficient into the dielectric spectra. Several Python routines that are commonly employed (e.g., SciPy and NumPy) are only required so that the users can alter the software structure depending on their needs. The modeling algorithm exploits the Markov chain Monte Carlo method for the data regression. The discrete relaxation models can be built by a proper combination of well-known relaxation models. In addition to these models, the electrode polarization, which is a common measurement artifact for interpreting the dielectric spectra, can be incorporated in the modeling algorithm. A continuous relaxation model, which solves the Fredholm integral equation of the first kind (a mathematically ill-posed problem) is also included.

Yoon, Tae-Jun↗
DOE OSTI2021

Dielectric metasurfaces made from vertically oriented nanoresonators

Dielectric metasurfaces control optical wavefronts via nanoscale resonators laid out across a surface. However, most metasurfaces are, by design, planar. In this work, we demonstrate the ability to fabricate dielectric metasurfaces with vertically oriented dielectric resonators using membrane projection lithography. We first numerically characterize the resonant modes of an array of vertically oriented germanium ellipses with no substrate and identify a narrowband region where the resonators satisfy the first Kerker condition. We then fabricate seven metasurfaces by depositing germanium ellipses onto walls of a 3D micrometer-sized silicon nitride photonic scaffold and characterize their transmission. We find that signatures of the multipolar modes seen in the unsupported array persist in the supported array, but the overall behavior is more complicated due to the scaffold. Further, we show that for a conceptual metasurface containing two coupled, vertically oriented ellipses, the ellipses can generate a sharp resonance with a quality factor of 240.

Gennaro, Sylvain D. (ORCID:0000000222090831)↗
DOE OSTI2021

Measurement and control of optical nonlinearities in dispersive dielectric multilayers

Dispersive dielectric multilayer mirrors, high-dispersion chirped mirrors in particular, are widely used in modern ultrafast optics to manipulate spectral chirps of ultrashort laser pulses. Dispersive mirrors are routinely designed for dispersion compensation in ultrafast lasers and are assumed to be linear optical components. In this work, we report the experimental characterization of an unexpectedly strong nonlinear response in these chirped mirrors. At modest peak intensities <2 TW/cm 2 —well below the known laser-induced damage threshold of these dielectric structures—we observed a strong reflectivity decrease, local heating, transient spectral modifications, and time-dependent absorption of the incident pulse. Through computational analysis, we found that the incident laser field can be enhanced by an order of magnitude in the dielectric layers of the structure. The field enhancement leads to a wavelength-dependent nonlinear absorption, that shows no signs of cumulative damage before catastrophic failure. The nonlinear absorption is not a simply two-photon process but instead is likely mediated by defects that facilitate two-photon absorption. To mitigate this issue, we designed and fabricated a dispersive multilayer design that strategically suppresses the field enhancement in the high-index layers, shifting the high-field regions to the larger-bandgap, low-index layers. This strategy significantly increases the maximum peak intensity that the mirror can sustain. However, our finding of an onset of nonlinear absorption even at ‘modest’ fluence and peak intensity has significant implications for numerous past published experimental works employing dispersive mirrors. Additionally, our results will guide future ultrafast experimental work and ultrafast laser design.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗