Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “data similarity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

Creep-rupture behavior of 6 candidate stirling engine iron-base superalloys in high pressure hydrogen. Volume 1: Air creep-rupture behavior

Four wrought alloys (A-286, IN 800H, N-155, and 19-9DL) and two cast alloys (CRM-6D and XF-818) were tested to determine their creep-rupture behavior. The wrought alloys were used in the form of sheets of 0.89 mm (0.035 in.) average thickness. The cast alloy specimens were investment cast and machined to 6.35 mm (0.250 in.) gage diameter. All specimens were tested to rupture in air at different times up to 3000 h over the temperature range of 650 C to 925 C (1200 F to 1700 F). Rupture life, minimum creep rate, and time to 1% creep strain were statistically analyzed as a function of stress at different temperatures. Temperature-compensated analysis was also performed to obtain the activation energies for rupture life, time to 1% creep strain, and the minimum creep rate. Microstructural and fracture analyses were also performed. Based on statistical analyses, estimates were made for stress levels at different temperatures to obtain 3500 h rupture life and time to 1% creep strain. Test results are to be compared with similar data being obtained for these alloys under 15 MPa (2175 psi) hydrogen.

Bhattacharyya, S.↗

The computation of mesh configurations for three-dimensional flow analysis

A geometry modeling method was developed to define three-dimensional mesh configurations, which were expressed by the set of surface intersections with a coordinate mesh. These configurations define bodies for transonic potential-flow computation in simple physical coordinates. Various configurations were prepared for 3-D potential flow analysis, including many bare inlet models in cylindrical coordinates. Trimmed surface models were used to prepare nacelle installation configurations. A variety of ducts and mixers were represented. Analytically defined mesh/surface intersections were compared with similar data obtained from the corresponding surface model. Parameters for an analytic surface definition from mesh-surface intersections obtained from a model of the surface were produced. In both studies the modeling accuracy was shown to be compatible with the flow analysis requirements. This technique fulfills the requirements of the associated three-dimensional potential-flow analysis. It preserves the flow analysis method's superior flexibility for adapting to unusual geometries. The geometry modeling technique is supported by a sufficient set of tools for effective use by general users, and sufficient accuracy was demonstrated.

Gibson, S. G.↗

Response measurements for two building structures excited by noise from a large horizontal axis wind turbine generator

Window and wall acceleration measurements and interior noise measurements ere made for two different building structures during excitation by noise from the WTS-4 horizontal axis wind turbine generator operating in a normal power generation mode. With turbine noise input pulses resulted in acceleration pulses for the wall and window elements of the two tests buildings. Response spectra suggest that natural vibration modes of the structures are excited. Responses of a house trailer were substantially greater than those for a building of sturdier construction. Peak acceleration values correlate well with similar data for houses excited by flyover noise from commercial and military airplanes and helicopters, and sonic booms from supersonic aircraft. Interior noise spectra have peaks at frequencies corresponding to structural vibration modes and room standing waves; and the levels for particular frequencies and locations can be higher than the outside levels.

Hubbard, H. H.↗

Particle distributions in approximately 10(13) - 10(16) eV air shower cores at mountain altitude and comparison with Monte Carlo simulations

Photographs of 521 shower cores in an array of current-limited spark (discharge) chambers at Sacramento Peak (2900m above sea level, 730 g /sq cm.), New Mexico, U.S.A., have been analyzed and the results compared with similar data from Leeds (80m above sea level, 1020 g sq cm.). It was found that the central density differential spectrum is consistent with a power law index of -2 up to approx. 1500/sq m where it steepens, and that shower cores become flatter on average with increasing size. Scaling model predictions for proton primaries with a approx E sup -2.71 energy spectrum account well for the altitude dependence of the data at lower densities. However, deviations at higher densities indicate a change in hadron interaction characteristics between approx few x 10 to the 14th power and 10 to the 15th power eV primary energy causing particles close to the shower axis to be spread further out.

Ash, A. G.↗

Jovian seismology

It is hypothesized that observations of the Doppler shifting of IR and UV absorption lines may furnish a powerful method for the detection of 4.5-9 min standing acoustic waves trapped in a wave duct beneath the Jupiter tropopause. Similarly, data could be obtained on Jupiter's thermal and density structure, and on the depth to which its zonal winds penetrate. The present model of standing oscillations in the molecular hydrogen envelope gives attention to theoretical eigenfrequencies and to such forcing functions for wave generation as coupling with turbulent and convective motions, thermal instability due to radiative transfer, wave propagation effects in a saturated atmosphere, and ortho-to-parahydrogen conversion. The small contribution that the forcing mechanisms make to velocity amplitudes implies that the Doppler shifting caused by the waves may only be resolvable through the superposition of oscillation records to enhance S/N ratios.

Bercovici, D.↗

Dislocation dynamics and the viscoplastic buckling of dendritic web type silicon ribbon

The effect of dendrites (reinforced edges) on the residual stresses, dislocation densities and buckling behavior during growth of web type silicon ribbon is studied. A viscoplastic material response function (Haasen-Sumino model) is used to calculate the stresses and the disloction density at each point in the silicon ribbon. In addition, the role of dendrites on the viscoplastic buckling behavior of the ribbon is investigated. The critical thicknesses, the corresponding deflection shapes and lateral deflection speeds are calculated. These results are then compared with similar data obtained for flat plates.

Tsai, C. T.↗

The design and performance of a multi-stream droplet generator for the liquid droplet radiator

Results are presented for the performance capabilities of a multistream droplet generator suitable for use in a spacecraft liquid droplet radiator heat-rejection system. The nozzle-motion mode of stream perturbation initiation was tested with a single droplet stream and found to produce data similar to those generated with the resonant cavity mode of perturbation. Tests then proceeded to a 26-orifice array; the streams of the array responded to the perturbation satisfactorily, forming uniformly separated drops.

Orme, Melissa↗

Speckle noise reduction of 1-look SAR imagery

Speckle noise is inherent to synthetic aperture radar (SAR) imagery. Since the degradation of the image due to this noise results in uncertainties in the interpretation of the scene and in a loss of apparent resolution, it is desirable to filter the image to reduce this noise. In this paper, an adaptive algorithm based on the calculation of the local statistics around a pixel is applied to 1-look SAR imagery. The filter adapts to the nonstationarity of the image statistics since the size of the blocks is very small compared to that of the image. The performance of the filter is measured in terms of the equivalent number of looks (ENL) of the filtered image and the resulting resolution degradation. The results are compared to those obtained from different techniques applied to similar data. The local adaptive filter (LAF) significantly increases the ENL of the final image. The associated loss of resolution is also lower than that for other commonly used speckle reduction techniques.

Nathan, Krishna S.↗

Ground vortex flow field investigation

Flow field investigations were conducted at the NASA Ames-Dryden Flow Visualization Facility (water tunnel) to investigate the ground effect produced by the impingement of jets from aircraft nozzles on a ground board in a STOL operation. Effects on the overall flow field with both a stationary and a moving ground board were photographed and compared with similar data found in other references. Nozzle jet impingement angles, nozzle and inlet interaction, side-by-side nozzles, nozzles in tandem, and nozzles and inlets mounted on a flat plate model were investigated. Results show that the wall jet that generates the ground effect is unsteady and the boundary between the ground vortex flow field and the free-stream flow is unsteady. Additionally, the forward projection of the ground vortex flow field with a moving ground board is one-third less than that measured over a fixed ground board. Results also showed that inlets did not alter the ground vortex flow field.

Kuhn, Richard E.↗

An in-flight investigation of ground effect on a forward-swept wing airplane

A limited flight experiment was conducted to document the ground-effect characteristics of the X-29A research airplane. This vehicle has an aerodynamic platform which includes a forward-swept wing and close-coupled, variable incidence canard. The flight-test program obtained results for errors in the airdata measurement and for incremental normal force and pitching moment caused by ground effect. Correlations with wind-tunnel and computational analyses were made. The results are discussed with respect to the dynamic nature of the flight measurements, similar data from other configurations, and pilot comments. The ground-effect results are necessary to obtain an accurate interpretation of the vehicle's landing characteristics. The flight data can also be used in the development of many modern aircraft systems such as autoland and piloted simulations.

Curry, Robert E.↗

Ozone profile measurements of McMurdo Station, Antarctica, during the spring of 1987

Ozone and temperature profiles were measured in 50 balloon flights at McMurdo Station (78 deg S) during the spring of 1987. Compared to similar data obtained in 1986, stratospheric temperatures were lower and the spring time Antarctic ozone reduction was greater in magnitude, extended to higher altitude, and proceeded at a higher rate in 1987. Ozone partial pressures reached values as low as 3 nbar (as compared to about 10 nbar in 1986) in the 16- to 18-km region in early and late October, down from about 150 nbar in late August. These low values suggest essentially complete removal of ozone in this region. The upper boundary of the depletion region was observed to be 2-3 km higher than in 1986, extending to altitudes as high as 24 km in mid-September. When averaged over September, the ozone mixing ratio at 18 km decayed with a half-life of only 12.4 days, as compared to about 28 days in 1986. Adiabatic vertical motions over 1- to 2-km intervals between 12 and 20 km with consequent ozone reductions were observed in association with the formation of nacreous clouds, indicating these to be rare events on a local scale probably associated with mountain lee waves.

Hofmann, D. J.↗

Nonequilibrium and equilibrium shock front radiation measurements

The intensities of the radiation emitted behind a normal shock wave in N were measured in an electric-arc driven shock tube at a shock velocity of 6.2 km/sec. Both a time-resolved broad-band radiation intensity measurement and a time-frozen spectral measurement were conducted. The rotational and vibrational temperatures are determined in both the equilibrium and the nonequilibrium regions. The results are compared with the similar data obtained by Allen et al. (1961). The measured rotational temperature seems to be in nonequilibrium, contradicting the two-temperature assumption of Park (1988), but the measured vibrational temperature agrees with Park's model.

Sharma, Surendra P.↗

High brightness neutral hydrogen in M31: A new probe of interstellar pressure

An observational parameter of our own Galaxy, the peak brightness temperature of neutral hydrogen in emission, was determined almost twenty years ago (Burton 1970). This quantity, although possessing a degree of local variations, has a remarkably consistent peak value of 125 K towards spiral arm segments with a few isolated peaks extending to 135 K, once sufficient spatial and velocity resolution are used (less than or equal to 70 pc, less than or equal to 5 km/s) to resolve the emission peaks. The higher spatial and velocity resolution of more recent surveys has not led to the detection of higher brightnesses. For many years this remarkable observational result has received little attention, primarily because similar data for other galaxies, which would allow a meaningful comparison and analysis, did not exist. Recently this situation has changed. A Westerbork survey of M33 (Deul and Van der Hulst 1987, and private comm.) with 40 pc x 8 km/s resolution has revealed consistent peak values of only 95 plus or minus 5 K (although there is still some question of whether the velocity resolution was sufficient in this case), while a Very Large Array (VLA) survey of M31 (Braun 1989a) with 35 pc x 5 km/s resolution has shown consistent peak values but at a temperature of 155 to 165 K. It has become clear that although peak HI brightness seems to be a well-defined quantity within individual galaxies (with a degree of local variation) there are very significant differences in this quantity amongst different galaxies. Researchers embarked on an observational program directed at a sample of 11 nearby galaxies: NGC 55, 247, 7793, 3031, 2366, 2403, 4236, 4826, 4736, 4244, and 5457. They hope to determine the gas properties and phases as a function of both galaxy type and position within the galaxies utilizing high resolution HI observations and optical narrow band imagery and spectroscopy which are now underway.

Braun, Robert↗

Multi-color imaging of selected southern interacting galaxies

The authors present preliminary results from a study of selected Arp-Madore Southern Hemisphere peculiar galaxies. Broadband charge coupled device (CCD) images (BVRI) of a subset of these galaxies allow us to study each galaxy's optical morphology, color, and (in a crude manner) degree of nuclear activity, and to compare them with similar data we possess on other active galaxies. Many of these galaxies have optical morphologies closely resembling those of powerful radio galaxies (Smith and Heckman 1989), yet their radio emission is unremarkable. Accurate positions for subsequent spectroscopic studies have been determined along with broad band photometry and morphology studies. Detailed observations of these comparatively bright, low-redshift, well-resolved interacting systems should aid our understanding of the role interactions play in triggering galaxy activity. This work is the initial effort in a long term project to study the role played by the dynamics of the interaction in the production and manifestations of activity in galaxies, and the frequency of galaxy mergers.

Smith, Eric P.↗

A novel method of testing the shear strength of thick honeycomb composites

Sandwich composites of aluminum and glass/phenolic honeycomb core were tested for shear strength before and after impact damage. The assessment of shear strength was performed in two ways; by four point bend testing of sandwich beams and by a novel double lap shear (DLS) test. This testing technique was developed so smaller specimens could be used, thus making the use of common lab scale fabrication and testing possible. The two techniques yielded similar data. The DLS test gave slightly lower shear strength values of the two methods but were closer to the supplier's values for shear strength.

Hodge, A. J.↗

Weight, center of gravity and modal test report for NTF fan blade set no. 3

A complete set of fan blades for the National Transonic Facility (NTF) at the NASA Langley Research Center was recently fabricated by Dynamic Engineering Inc. (DEI). These blades were the third complete set of blades fabricated by the NTF. The first set of blades was fabricated by NASA and installed in the tunnel in December 1981. This original set was destroyed in a mishap in January 1989. The second set of blades is currently in use in the NTF. The third set of blades recently fabricated by DEI is a spare set. In order to ensure that the blades met the requirements, DEI performed a series of tests on each of the completed blades. In addition, a model survey was conducted on each blade to define the dynamic characteristics. Discussed here are the blade tests conducted by DEI and the test results. The test set-ups and procedures are discussed in detail. The results obtained for each of the 27 blades are documented and comparisons are made between this set of blades and similar data for two previous sets of NTF fan blades.

Friedman, Inger P.↗

Galactic OB associations in the northern Milky Way Galaxy. I - Longitudes 55 deg to 150 deg

The literature on all OB associations was reviewed, and their IRAS point source content was studied, between galactic longitude 55 and 150 deg. Only one third of the 24 associations listed by Ruprecht et al. (1981) have been the subject of individual studies designed to identify the brightest stars. Distances to all of these were recomputed using the method of cluster fitting of the B main sequence stars, which makes it poossible to reexamine the absolute magnitude calibration of the O stars, as well as for the red supergiant candidate stars. Also examined was the composite HR diagram for these associations. Associations with the best defined main sequences, which also tend to contain very young clusters, referred to here as OB clusters, have extremely few evolved B and A or red supergiants. Associations with poorly defined main sequences and few OB clusters have many more evolved stars. They also show an effect in the upper HR diagram referred to as a ledge by Fitzpatrick and Garmany (1990) in similar data for the Large Magellanic Cloud. It is suggested that the differences in the associations are not just observational selection effects but represent real differences in age and formation history.

Garmany, C. D.↗

A payload to evaluate photodiodes for the detection of soft and hard x rays in a space environment using a Get Away Special

We propose to use the Get Away Special (GAS) facility to evaluate P-intrinsic-N (PIN) detectors and avalanche photodiodes (APD's) for the detection of both solar and nonsolar soft and hard x rays. We would like to fly both types of silicon detectors for the direct detection of the x ray photons in the energy range from 1 to 30 keV with an energy resolution of about 1 keV. We would also like to use both types of photodiodes viewing CsI(Tl) scintillators to extend the energy range up to 1 MeV with -6 percent resolution at 660 keV. Solar flares would be detected with this instrumentation during periods of solar pointing providing high energy resolution spectra with high time resolution. Similar data would be obtained in the scanning mode on nonsolar transient and steady x ray sources with the same instrumentation. A commandable door over the detectors would be required to allow measurements to be made as low as 1 keV.

Desai, Upendra D.↗