Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “composition and microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

High temperature steam oxidation dynamics of U 3 Si 2 with alloying additions: Al, Cr, and Y

Uranium silicides are considered for advanced technology reactor fuels due to their enhanced thermal conductivity and high uranium density (U 3 Si and U 3 Si 2 ) compared to traditional UO 2 . Susceptibility to oxidation and wash out, in the event of a cladding breech, could limit the potential for deployment of silicides as accident tolerant fuels. Mitigating the water reaction for U 3 Si 2 could enable its use as an accident tolerant, high uranium density fuel or as a composite fuel constituent. Reported here is the impact of alloying additions of Al, Cr and Y on the high temperature, steam oxidation response of U 3 Si 2 . In addition to the thermogravimetric response, as melted microstructures, phase compositions and post oxidation analysis are also presented. Here, the investigation shows steam oxidation dynamics are altered, from non-alloyed U 3 Si 2 , under thermally ramped conditions. However, additional alloy development of these fuel forms is necessary for further consideration as candidate accident tolerant fuels in water-cooled reactor designs.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Creep in multi-principal element materials –– A review

The ongoing push towards enhanced energy efficiency and reduced emissions has necessitated the creation of materials with superior performance, especially under extreme conditions. Modern industries, such as aerospace, energy production, and nuclear power, rely heavily on materials that can withstand elevated temperatures without compromising structural integrity. At these heightened temperatures, materials, even when subjected to mechanical stresses well below their yield strength, may experience slow deformation leading to eventual rupture — a phenomenon known as creep. With the expansive design space that comes with the high entropy concept and their reported excellent high temperature strength, multi-principal element materials (MPEMs) have attracted interest in the scientific community for high-temperature applications. Here, this review offers a comprehensive examination of existing studies on creep in MPEMs, which includes multi-principal element−alloys, −bulk metallic glasses, −ceramics, and −superalloys, comparing published findings on MPEMs with pure elements, traditional alloys, bulk metallic glasses, and superalloys. The sub-topics covered include a comparison among different creep-testing methods, creep mechanisms, creep exponents, creep strain rates, activation volume, and creep-activation energy. Modeling efforts for predicting creep behavior of MPEMs are also reviewed. Methods for improving creep resistance by performing heat treatments and/or modifying microstructures are discussed. Overall, the current state of MPEMs has not yet surpassed the creep performance of commercial alloys. Finally, directions for future efforts are suggested, such as experimenting in various controlled environments, expanding the number of compositions tested, exploring advanced manufacturing techniques, and using machine-learning to predict creep properties based on compositions and microstructures.

36 MATERIALS SCIENCE↗
NASA NTRS1984

Microanalytical study of some cosmic dust discovered in sea-floor sediments in China

The study of cosmic dust can provide useful data in the investigation of the origin of the Earth and the evolution of celestial bodies. Three types of cosmic dust (ferriginous, siliceous, and glassy) were discovered in the seafloor sediments near China. Their chemical composition and microstructure were examined by X-ray diffraction, fractography, and electron microscopy. The major mineral in an iron-containing cosmic dust is magnetite. The silicate spheres contain sundry metals and metal oxides. Glassy microtektites are similar in composition to tektites, and are found in all the major meteorite areas worldwide.

Shijie, Z.↗
DOE OSTI2023

Additive Manufacturing of Poly(phenylene Sulfide) Aerogels via Simultaneous Material Extrusion and Thermally Induced Phase Separation

Abstract Additive manufacturing (AM) of aerogels increases the achievable geometric complexity, and affords fabrication of hierarchically porous structures. In this work, a custom heated material extrusion (MEX) device prints aerogels of poly(phenylene sulfide) (PPS), an engineering thermoplastic, via in situ thermally induced phase separation (TIPS). First, pre‐prepared solid gel inks are dissolved at high temperatures in the heated extruder barrel to form a homogeneous polymer solution. Solutions are then extruded onto a room‐temperature substrate, where printed roads maintain their bead shape and rapidly solidify via TIPS, thus enabling layer‐wise MEX AM. Printed gels are converted to aerogels via postprocessing solvent exchange and freeze‐drying. This work explores the effect of ink composition on printed aerogel morphology and thermomechanical properties. Scanning electron microscopy micrographs reveal complex hierarchical microstructures that are compositionally dependent. Printed aerogels demonstrate tailorable porosities (50.0–74.8%) and densities (0.345–0.684 g cm −3 ), which align well with cast aerogel analogs. Differential scanning calorimetry thermograms indicate printed aerogels are highly crystalline (≈43%), suggesting that printing does not inhibit the solidification process occurring during TIPS (polymer crystallization). Uniaxial compression testing reveals that compositionally dependent microstructure governs aerogel mechanical behavior, with compressive moduli ranging from 33.0 to 106.5 MPa.

Chemistry↗
DOE OSTI2025

Shielded magnetic small-angle neutron scattering for characterization of radioactive samples

The development of a Pb-shielded fixture for the execution of a small-angle neutron scattering (SANS)-based workflow for interrogation of highly irradiated nuclear materials has been explored. The Pb shielding was specially designed to reduce the detected radioactivity from the specimen during SANS experiments, and the overall configuration is termed shielded magnetic SANS (SM-SANS). Two FeCrAl-based alloys, C35M and 125YF, were examined with the SM-SANS technique using a free-form size distribution locally monodisperse model in both the as-received and irradiated states. Quantitative values derived from the free-form size distribution were compared with atom probe tomography experiments. Microstructural and compositional parameters determined using the two characterization techniques were complements of each other. The results demonstrate that the SM-SANS technique is an effective means of characterizing nanoscale clustering in irradiated material systems and provides new avenues for investigating radioactive material microstructures.

FeCrAl↗
NASA NTRS2004

LiCoO2 and SnO2 Thin Film Electrodes for Lithium-Ion Battery Applications

There is an increasing need for small dimension, ultra-lightweight, portable power supplies due to the miniaturization of consumer electronic devices. Rechargeable thin film lithium-ion batteries have the potential to fulfill the growing demands for micro-energy storage devices. However, rechargeable battery technology and fabrication processes have not kept paced with the advances made in device technology. Economical fabrication methods lending excellent microstructural and compositional control in the thin film battery electrodes have yet to be fully developed. In this study, spin coating has been used to demonstrate the flexibility of the approach to produce both anode (SnO2) and cathode (LiCoO2) thin films. Results on the microstructure crystal structure and electrochemical properties of the thin film electrodes are described and discussed.

Maranchi, Jeffrey P.↗
DOE OSTI2021

Thermal diffusivity and thermal conductivity of SiC composite tubes: the effects of microstructure and irradiation

Cladding thermal conductivity is an important physical property in assessing the performance of silicon carbide (SiC)-cladded fuels for nuclear reactors. However, there is a significant lack of reliable data, particularly for irradiated materials, because the geometry complicates the measurement. This study investigates the thermal diffusivity of coupons with a curvature, machined from SiC fiber–reinforced SiC matrix composite tubes, with and without neutron irradiation under light water reactor–relevant temperature and dose conditions. The tested materials included full composite and duplex SiC composite tubes. The measurements were conducted using a modern flash diffusivity apparatus. The analyzed area on the specimen during diffusivity testing was reduced for improved measurement accuracy due to sample curvature. Post-irradiation measurements showed that the effects of neutron irradiation on thermal conductivity (e.g. thermal defect resistivity) are different between SiC composite plates versus tubes. The difference was explained by higher matrix density of the tube than the plate. This study provides reliable thermal properties of prototypic SiC composite tubes useful for fuel performance modeling of SiC-based cladding.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRSDate not supplied

Design Considerations for Practical Li-S Batteries for Electric Aviation

The development of high-energy, high-safety, and high-power batteries beyond electric automotive standards is critical for future electric aviation applications. Non-volatile solid-state electrolytes (SSE) offer many promising advantages over traditional flammable liquid electrolytes. Solid-state electrolytes may be an enabling technology for certain battery chemistries by preventing detrimental interactions with liquid electrolytes, for example prevention of the dissolution of intermediates in lithium-sulfur common in traditional liquid organic solvents. However, significant manufacturing challenges must be overcome before the adoption of such technology. This research was conducted to identify processing techniques for producing solid-state battery components with practical dimensions and weights for enabling high specific energy cells. Traditional research has identified a range of very high theoretical ionic conductivities but are impractical due to their instability or inability to be manufactured. Electrolytes explored in this study were produced as sulfide-polymer composites with densified thicknesses below 40 micron using a tape-casting technique and thermoplastic elastomer binder. The combination of high chemical compatibility and flexibility produced robust films that had moderate impact on the ionic conductivity but was capable of dramatically reducing the parasitic mass. Despite minimal conductivity losses, films were produced 10-15 times thinner than comparable bulk powder electrolytes thus leading to overall lower film resistance. Conductivity is maintained above 0.2mS/cm for composite electrolytes. Through the analysis of materials based on their physical properties, such as density, practical cells can be designed. Based on this, low density sulfide-solid-state electrolytes are a promising candidate for achieving the energy and safety metrics for electric aviation, however, further optimization of cathode microstructure and composite processing will be required to achieve the high power metrics and will be the focus of further studies. Additionally, fabrication challenges arise when utilizing metallic lithium foil, due to its soft nature, as overflow and mechanical short circuit can occur on assembly which remains a challenge to overcome before metallic lithium anodes can be fully realized.

batteries↗
DOE OSTI2024

Upcycled high-strength aluminum alloys from scrap through solid-phase alloying

Although recycling secondary aluminum can lead to energy consumption reduction compared to primary aluminum manufacturing, products produced by traditional melt-based recycling processes are inherently limited in terms of alloy composition and microstructure, and thus final properties. To overcome the constraints associated with melting, we have developed a solid-phase recycling and simultaneous alloying method. This innovative process enables the alloying of 6063 aluminum scrap with copper, zinc, and magnesium to form a nanocluster-strengthened high-performance aluminum alloy with a composition and properties akin to 7075 aluminum alloy. The unique nanostructure with a high density of Guinier-Preston zones and uniformly precipitated nanoscale η‘/Mg(CuZn) 2 strengthening phases enhances both yield and ultimate tensile strength by >200%. By delivering high-performance products from scrap that are not just recycled but upcycled , this scalable manufacturing approach provides a model for metal reuse, with the option for on-demand upcycling of a variety of metallic materials from scrap sources.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Combinatorial Cu-Ni Alloy Thin-Film Catalysts for Layer Number Control in Chemical Vapor-Deposited Graphene

We synthesized a combinatorial library of CuxNi1−x alloy thin films via co-sputtering from Cu and Ni targets to catalyze graphene chemical vapor deposition. The alloy morphology, composition, and microstructure were characterized via scanning electron microscopy (SEM), energy dispersive x-ray spectroscopy (EDS), and X-ray diffraction (XRD), respectively. Subsequently, the CuxNi1−x alloy thin films were used to grow graphene in a CH4-Ar-H2 ambient at atmospheric pressure. The underlying rationale is to adjust the CuxNi1−x composition to control the graphene. Energy dispersive x-ray spectroscopy (EDS) analysis revealed that a continuous gradient of CuxNi1−x (25 at. % < x < 83 at.%) was initially achieved across the 100 mm diameter substrate (~0.9%/mm composition gradient). The XRD spectra confirmed a solid solution was realized and the face-centered cubic lattice parameter varied from ~3.52 to 3.58 A˙, consistent with the measured composition gradient, assuming Vegard’s law. Optical microscopy and Raman analysis of the graphene layers suggest single layer growth occurs with x > 69 at.%, bilayer growth dominates from 48 at.% < x < 69 at.%, and multilayer (≥3) growth occurs for x < 48 at.%, where x is the Cu concentration. Finally, a large area of bi-layer graphene was grown via a CuxNi1−x catalyst with optimized catalyst composition and growth temperature.

2D materials↗
NASA NTRS1992

Near-tip dual-length scale mechanics of mode-I cracking in laminate brittle matrix composites

This paper presents the preliminary results of an on-going study of the near-tip mechanics of mode-I cracking in brittle matrix composite laminates. A finite element model is developed within the context of two competing characteristic lengths present in the composite: the microstructural length (the thickness of the layers) and a macro-length (crack-length, uncracked ligament size, etc.). For various values of the parameters which describe the ratio of these lengths and the constituent properties, the stresses ahead of a crack perpendicular to the laminates are compared with those predicted by assuming the composite is homogeneous orthotropic. The results can be used to determine the conditions for which homogenization can provide a sufficiently accurate description of the stresses in the vicinity of the crack-tip.

Ballarini, R.↗
DOE OSTI2026

Thermal cycling-driven microstructural changes of eutectic Al–Si phase change materials in SS304 containers revealed by multi-modal imaging

Aluminum-based Al–Si alloys are widely used as phase change materials (PCMs) in thermal energy storage (TES) systems owing to their high volumetric latent heat and superior thermal conductivity. However, their long-term reliability is limited by degradation processes that remain insufficiently understood. In this work, we employ a multimodal, correlative characterization framework to systematically resolve the degradation behavior of eutectic Al–Si PCMs in contact with SS304 containers under repeated thermal cycling. By integrating high-resolution electron microscopy, three-dimensional X-ray fluorescence (3D XRF) imaging, and differential scanning calorimetry (DSC), we directly link spatially resolved compositional and microstructural evolution to changes in thermophysical properties. The correlative analysis reveals that elemental leaching of Fe, Cr, and Ni from the stainless-steel container into the PCM drives the formation of intermetallic compounds (IMCs) both at the interface and within the bulk PCM, leading to pronounced compositional heterogeneity. These interfacial reactions and diffusion-induced transformations progressively destabilize the Al–Si eutectic, reducing the effective phase-transforming fraction. Consistent with these observations, DSC measurements show a decrease in melting temperature and latent heat of fusion with thermal cycling. These results underscore the critical influence of interfacial reactions and material compatibility on the stability, durability, and overall performance of Al–Si-based TES systems.

25 ENERGY STORAGE↗
DOE OSTI2024

Machine-learning-assisted deciphering of microstructural effects on ionic transport in composite materials: A case study of Li 7 La 3 Zr 2 O 12 -LiCoO 2

The effective diffusivity of ionic species in multiphase materials is critical for the design and function of composite materials for electrochemical energy storage. In practice, effective diffusivity depends sensitively not only on the intrinsic diffusivities of constituting materials but also on their topological arrangement; nevertheless, these coupled contributions are oversimplified in most analytical models. Here, we combine atomistically informed mesoscale modeling and machine learning (ML) analysis to unravel how such features affect effective diffusivity in two-phase composites. Using the Li 7 La 3 Zr 2 O 12 -LiCoO 2 composite solid-state battery cathode as a model system, we compute effective diffusivity for 600 distinct dense polycrystalline microstructures with different topological configurations of grains, grain boundaries, and heterointerfaces. We verify that in addition to atomic-scale variabilities, microstructural feature diversity can significantly impact effective transport properties. Across the ensemble of test microstructures, this often results in bimodal distributions of effective diffusivity that encompass two qualitatively distinct operating mechanisms, which we identify via flux analysis. An ML approach reveals that the most critical determining factors for effective diffusivity are the connectivity of bulk phases and their heterointerfaces. The role of ionic mobility at the heterointerfaces is also discussed. These insights highlight the combined importance of microstructure and interface engineering in tuning the transport properties of ionic species in composite materials. In conclusion, our framework can also be extended for understanding generic microstructure-property relationships in other complex multiphase materials.

25 ENERGY STORAGE↗
DOE OSTI2021

Effects of as-received defects on ceramic matrix composites properties using high-fidelity microstructures with periodic boundary conditions

The presence of microstructural defects in as-received specimens of ceramic matrix composites (CMCs) significantly influences their constitutive response and damage, highlighting the importance of characterization and quantification of these defects for accurate assessment of damage and failure in the service environment. In a recent effort, the authors developed an algorithm to generate stochastic representative volume elements (SRVEs) of Carbon fiber Silicon-Carbide-Nitride matrix (C/SiNC) CMCs based on extensive multiscale material and defect characterization data. This paper implements this algorithm within a commercial finite element solver with periodic boundary conditions (PBCs) for high-fidelity micromechanics analysis and investigation of macroscopic material behavior of C/SiNC composites. Different loading directions are used to predict the global mechanical properties, and the results are in excellent agreement with theoretical (rule of mixture) predictions. Subsequently, the effects of as-received defects on the global and local responses are investigated. The results show that intratow porosity has pronounced degradation effects on the global elastic properties and results in complex stress localization patterns, which can be attributed to potential damage initiation sites.

Khafagy, Khaled H.↗
DOE OSTI2025

Tunable structure and reinforcement of polyvinyl alcohol (PVA) hydrogels using fungal chitin particles

Polysaccharides, including chitin, are one of the most abundant biopolymers in nature and are increasingly recognized as a sustainable alternative to petroleum-derived plastics and synthetic fillers in polymer composites. Traditionally sourced from crustacean shells, chitin offers mechanical strength and biocompatibility with limitations also in processability and functionality. Fungal-derived chitin material represents a promising alternative, with advantages including scalable fermentation on low-cost substrates, absence of shellfish allergens, and tunable molecular architectures that vary by species, developmental stage, and growth environment. Here, in this study, we systematically examined chitinous materials obtained from taxonomically and functionally distinct fungi, Laccaria bicolor, Trichoderma reesei and Rhizopus oryzae, to assess their structural, chemical, and morphological properties as reinforcement agents in polymer composites. Mild alkaline pretreatment was employed to obtain mycelium chitin particles, thereby improving accessibility to chitin and co-occurring β-D-glucans while maintaining microparticle integrity. Comprehensive FTIR and solid-state NMR analyses revealed species-specific differences in chemical composition and microstructure, with R. oryzae exhibiting a unique spectral signature. These fungal-derived chitin were then incorporated into poly(vinyl alcohol) (PVA) hydrogels, where they acted as reinforcing fillers without the need for additional chemical crosslinkers. Comparative evaluation of hydrogel properties demonstrated that fungal chitin significantly enhanced mechanical performance, with all mycelium fillers mitigating the water weakening in PVA hydrogels. R. oryzae-derived composites tripled the hydrogel tensile strength while the submicron fibrous morphology in L. bicolor contributes to over 45 % tensile improvement in dry PVA composites. Our findings highlight the potential of fungal biomass as a tunable, sustainable platform for producing chitin-based reinforcing agents.

Chitin↗
DOE OSTI2021

Effect of Nanoscale Ce 0.8 Gd 0.2 O 2–δ Infiltrant and Steam Content on Ni–(Y 2 O 3 ) 0.08 (ZrO 2 ) 0.92 Fuel Electrode Degradation during High-Temperature Electrolysis

Studies of Ni–yttria-stabilized zirconia (YSZ) fuel electrode degradation mechanisms in solid oxide electrolysis cells (SOECs) are complicated by the different possible Ni–YSZ microstructures and compositions, and the variations in the H 2 /H 2 O ratio encountered in an electrolysis stack. Here, in this study, we describe a life testing scheme aimed at providing survey results on degradation as a function of the H 2 O–H 2 composition, with life tests carried out at five different steam contents from 90% to 10%. A Ni–YSZ-supported symmetric cell geometry is employed both with and without infiltrated nanoscale gadolinia-doped ceria (GDC). Impedance spectroscopy is utilized to observe changes in electrochemical characteristics during the life test, and a transmission-line-based equivalent circuit is used to model the data. Post-test electrode microstructures were observed. The results suggest that the GDC infiltrant reduces the electrode polarization resistance and provides more stable electrode polarization over a range of conditions.

08 HYDROGEN↗
DOE OSTI2025

Morphology and property tuning in ZnO–Ni hybrid metamaterials in vertically aligned nanocomposite (VAN) form

ZnO thin films have attracted significant interest in the past decades owing to their unique wide band gap properties, piezoelectric properties, non-linearity and plasmonic properties. Recent efforts have been made in coupling ZnO with secondary phases to enhance its functionalities, such as Au–ZnO nanocomposite thin films with tunable optical and plasmonic properties. In this work, magnetic nanostructures of Ni are incorporated in ZnO thin films in a vertically aligned nanocomposite (VAN) form to couple magnetic and plasmonic response in a complex hybrid metamaterial system. Nickel (Ni) is of interest due to its ferromagnetic and plasmonic properties along with gold (Au) which is also plasmonic. Therefore, two approaches, namely, tuning of the deposition pressure and use of a ZnO–Au seeding layer have been attempted to achieve unique Ni nanostructures in addition to tuning of the microstructure. Together, both approaches demonstrate a range of microstructures such as core–shell, nanodisk, nanocup, and nanocube-like morphologies not previously attempted. Additionally, there is effective tuning of properties. Specifically, the seeding layer thickness causes hyperbolic behavior as well as redshift in the surface plasmon resonance (SPR) wavelength. The addition of the ZnO–Au seeding layer directly influences the optical properties. Plus, regardless of the different approaches, the films demonstrate magnetic anisotropy based on the composition and microstructure of the film which impacted the saturation magnetization and coercivity. This study demonstrates the potential of ZnO-based complex hybrid metamaterials with coupled electro-magneto-optical properties for integrated photonic devices.

Bhatt, Nirali A. [Purdue Univ., West Lafayette, IN↗
NASA NTRS1990

Microstructure and magnetization of doped Y-Ba-Ca-O materials prepared by melt quench and post annealing method

Y-Ba-Cu-O bulk materials prepared using the melt quench and post annealing method were shown to have very high maximum as well as remanent magnetization. Studies were carried out on materials prepared using this method which deviate from the Y:Ba:Cu = 1:2:3 stoichiometry. In one series of materials, only the stoichiometry was changed, in particular by introducing an excess of yttrium. In other cases, dopants including several rare earths were introduced. Effects of variations in composition on microstructure and phase evolution are discussed, as well as effects on the magnetic susceptibility and on the magnetization. The results show that doped materials can exhibit improvements in magnetic properties. Furthermore, the use of dopants sheds light on the role of defect sites in flux pinning.

Hojaji, H.↗