Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “composite Li anode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Super p-sulfur cathodes for quasi-solid-state lithium-sulfur-batteries

Lithium-Sulfur (Li-S) batteries have become a promising candidate to meet the current energy storage demand, with its natural abundance of materials, high theoretical capacity of 1672 mAhg-1, high energy density of 2600 Whkg-1, low cost and lower environmental impact. Sulfide based solid state electrolytes (SSEs) have received greater attention due to their higher ionic conductivity, compatible interface with sulfur-based cathodes, and lower grain boundary resistance. However, the interface between SSEs and cathodes has become a challenge in all solid-state Li-S batteries due to the rigidity of the participating surfaces. A hybrid electrolyte containing SSE coupled with a small amount of ionic liquid, was essential to improve the interface contact of the SSE with the electrodes. Coating-based cathodes were successfully fabricated using water-based carboxymethyl cellulose (CMC) solution and Styrene butadiene rubber (SBR) as the binder with low sulfur loading (0.70 mgcm-2) as well as high sulfur loading (4.0 mgcm-2). Solid-state composite powder-based cathodes pressed onto SSE (loading 4.0 mgcm-2) with enhanced electronic and ionic conductivity were fabricated with Super P: Sulfur (SP:S) and SSE. Ionic Liquids (IL) prepared using Lithium bis(trifluoromethyl sulfonyl)imide (LiTFSI) as salt, with premixed pyrrolidinium bis(trifluoromethyl sulfonyl)imide (PYR) as solvent and 1,3-dioxolane (DOL) as diluent were used to wet both SSE-electrode interfaces. The effect of IL dilution, co-solvent amount, LiTFSI concentration, C rate at which the batteries are tested and the effect of SSE inside the cathode, were systematically studied and optimized to develop a quasi-solid-state electrolyte Li-S battery (QSSLSB) with higher capacity retention and cyclability. LiTFSI (2M) dissolved in PYR:DOL(1:1) found to be optimum IL combination for low sulfur loading QSSLSBs reaching 500 mAh/g after 100 cycles while LiTFSI (3M) in PYR:DOL(1:3) was the optimum IL concentration for higher loading QSSLSBs reaching 400 mAh/g after 100 cycles. This work reports promising results of QSSLSB based on novel Li6PS5F0.5Cl0.5 Li-argyrodite solid-state electrolyte (SSE) with minute amount of IL, Super P-Sulfur (SP:S) cathode, and Li-anode. It also offers a new insight into the intimate interfacial contacts between the SSE and carbon-sulfur cathodes, which will be critical for improved electrochemical performance of quasi-solid-state lithium-sulfur batteries with high sulfur loading in the future.

25 ENERGY STORAGE↗
DOE OSTI2020

The early-stage growth and reversibility of Li electrodeposition in Br-rich electrolytes

Significance Spatial variations in chemical composition and transport properties of the material phases (interphases) formed on reactive metals in liquid electrolytes are thought to be responsible for the propensity of metal battery electrodes to electrodeposit in irregular, nonplanar morphologies. Equilibrium theoretical calculations using joint density functional analysis in vacuum and generic liquid media indicate that in-plane transport at such interphases is enhanced substantially if LiX (X = Br > Cl > F) species predominate. This study employs optical visualization experiments and nucleation theory to experimentally investigate nucleation and early-stage growth dynamics of metallic lithium in electrolytes enriched with LiBr. It is shown that the Li-Br–rich interphases formed profoundly alter the morphology of Li electrodeposits by enhancing Li-ion surface diffusion.

25 ENERGY STORAGE↗
DOE OSTI2020

A review of composite solid-state electrolytes for lithium batteries: fundamentals, key materials and advanced structures

All-solid-state lithium ion batteries (ASSLBs) are considered next-generation devices for energy storage due to their advantages in safety and potentially high energy density. As the key component in ASSLBs, solid-state electrolytes (SSEs) with non-flammability and good adaptability to lithium metal anodes have attracted extensive attention in recent years. Among the current SSEs, composite solid-state electrolytes (CSSEs) with multiple phases have greater flexibility to customize and combine the advantages of single-phase electrolytes, which have been widely investigated recently and regarded as promising candidates for commercial ASSLBs. Based on existing investigations, herein, we present a comprehensive overview of the recent developments in CSSEs. Initially, we introduce the historical development from solid-state ionic conductors to CSSEs, and then summarize the fundamentals including mechanisms of lithium ion transport, key evaluation parameters, design principles, and key materials. Finally, four main types of advanced structures for CSSEs are classified and highlighted according to the recent progress. Moreover, advanced characterization and computational simulation techniques including machine learning are reviewed for the first time, and the main challenges and perspectives of CSSEs are also provided for their future development.

25 ENERGY STORAGE↗
DOE OSTI2023

3D Carbon Coating Enabled High‐capacity and Stable Micro‐sized Silicon Suboxide‐graphite Blended Anodes for Practical Lithium‐ion Batteries

Abstract Silicon oxide (SiO x ) is a promising anode candidate of lithium‐ion batteries (LIBs) owing to its extremely high specific capacity. However, the low initial Coulombic efficiency (ICE) and rapid capacity degradation of SiO x , triggered by the enormous volume variation upon repeated (de)lithiation, gravely hinder its practical use. Herein, two mass‐produced micro‐sized SiO x @C composites with obviously different morphologies for commercial LIBs are reported. Particularly, the SiO x ‐graphite blended anode (SiO x @3D‐G‐Gr) based on SiO x wrapped by three‐dimensional (3D) carbon layers (SiO x @3D‐G) exhibits a capacity of 519 mAh g −1 , an ICE of 90.0 % and a capacity retention of 83.4 % at 0.2 C over 100 cycles. which is far exceeding its counterpart SiO x @C‐H‐Gr (65.7 %). The obtained impressive properties of SiO x @3D‐G originate from the critical contribution of 3D carbon layers, which serves as the effective stress buffer and protective layer as well as the strong networks for electron/Li + transport. Accordingly, the full‐cell based on SiO x @3D‐G‐Gr anode and commercial LiCoO 2 cathode delivers a capacity of 803 mAh and an excellent capacity retention of 95.6 % (616 mAh, 96.6 % for graphite, respectively) at 1 C over 100 cycles with a stabilized CE of nearly 100 %. The micro‐sized SiO x @3D‐G showing a promising prospect in the commercial‐grade anodes in LIBs.

Electrochemistry↗
DOE OSTI2025

High‐Concentration Alcohol Generation in Bipolar Membrane CO Electrolyzer

Electrochemical reduction of carbon dioxide and carbon monoxide offers an electricity‐powered route to make multicarbon liquid products. However, in conventional systems employing anion exchange membranes (AEMs), significant liquid product crossover leads to dilute product streams, increasing separation costs; and also produces unwanted anodic oxidation, further decreasing overall efficiency. Here, we report a forward‐biased bipolar membrane (FB‐BPM) system that achieves <10% liquid product crossover while sustaining a highly alkaline environment near the cathode, suppressing ethylene and hydrogen and favoring liquid products. By tuning catalyst composition to modulate the adsorption of *H and *OH, we steer selectivity toward acetate and alcohols. Using the FB‐BPM system, we achieve >25 wt% acetate on CuZn and >15 wt% alcohols on CuSn directly from the cathode outlet stream.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Mechanistic Analysis of Microstructural Attributes to Lithium Plating in Fast Charging

Metallic lithium deposition on graphite anodes is a critical degradation mode in lithium-ion batteries, which limits safety and fast charge capability. A conclusive strategy to mitigate lithium deposition under fast charging yet remains elusive. Herein, we examine the role of electrode microstructure in mitigating lithium plating behavior under various operating conditions, including fast charging. The multilength scale characteristics of the electrode microstructure lead to a complex interaction of transport and kinetic limitations that significantly governs the cell performance and the occurrence of Li plating. We demonstrate, based on a comprehensive mesoscale analysis, that the performance and degradation can be significantly modulated via systematic design improvements at the hierarchy of length scales. It is found that the improvement in kinetic and transport characteristics achievable at disparate scales can dramatically affect Li plating propensity.

25 ENERGY STORAGE↗
DOE OSTI2022

Techno-economic analysis of non-aqueous hybrid redox flow batteries

Renewable energy has become indispensable to improving human life, but its growth is hampered by a lack of cost-effective energy storage systems to solve the intermittency problem. Non-aqueous hybrid redox flow batteries (NAqHRFBs), based on lithium metal anode and organic redox molecules (redoxmers), have been investigated as an attractive energy storage option because of their high cell voltages and energy densities compared to other redox flow battery candidates. However, little is known about the economic potential of NAqHRFBs, as well as the operational and materials impacts. This research establishes a techno-economic model to analyze the capital costs of NAqHRFBs with selected organic redoxmers, including 2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO). Sensitivity analyses for current density, area-specific resistance, cell voltage, electrolyte composition, redoxmer price, and equivalent molecular weight indicate the key factors in controlling NAqHRFB capital cost. To make the current NAqHRFB cost-effective, the first priority is to increase the operation current density over 10 times of those used in lab-scale tests, followed by adjusting redoxmer-related characteristics to afford more cost reduction space such as decreasing the unit price by ~20 fold. The results have shed light on potential material development and system engineering directions to make NAqHRFBs viable for renewable energy storage.

25 ENERGY STORAGE↗
DOE OSTI2025

Advancements in active filler-contained polymer solid-state electrolytes for lithium-metal batteries: A concise review

Lithium-metal batteries (LMBs) usually are regarded as the pinnacle of next-generation energy storage due to the high specific capacity and low redox potential of the Li-metal anode. However, their development is hindered by safety hazards related to flammable electrolytes and uncontrolled side reactions within the battery. Both polymer and solid-state inorganic electrolytes, despite their potential, exhibit shortcomings that limit their practical applications. Active filler-containing polymer electrolytes (AFPEs) offer a promising solution by combining the benefits of both types. Enhanced by supramolecular interactions between the polymer matrix and active fillers, AFPEs demonstrate superior electrochemical performance over traditional polymer electrolytes. This review discusses the progress in active fillers and various polymer matrices, examining the factors that enhance performance, particularly ionic conductivity. It also outlines the future research directions of AFPEs, aiming to broaden the application of solid electrolytes in high-performance LMBs.

All solid-state batteries↗
DOE OSTI2023

Understanding the Chemomechanical Function of the Silver–Carbon Interlayer in Sheet-type All-Solid-State Lithium–Metal Batteries

All-solid-state batteries with lithium metal anodes hold great potential for high-energy battery applications. However, forming and maintaining stable solid–solid contact between the lithium anode and solid electrolyte remains a major challenge. One promising solution is the use of a silver–carbon (Ag–C) interlayer, but its chemomechanical properties and impact on interface stabilities need to be comprehensively explored. Here, we examine the function of Ag–C interlayers in addressing interfacial challenges using various cell configurations. Experiments show that the interlayer improves interfacial mechanical contact, leading to a uniform current distribution and suppressing lithium dendrite growth. Furthermore, the interlayer regulates lithium deposition in the presence of Ag particles via improved Li diffusivity. The sheet-type cells with the interlayer achieve a high energy density of 514.3 Wh L –1 and an average Coulombic efficiency of 99.97% over 500 cycles. Furthermore, this work provides insights into the benefits of using Ag–C interlayers for enhancing the performance of all-solid-state batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Enhanced Electrochemical Performance of Disordered Rocksalt Cathodes Enabled by a Graphite Conductive Additive

Cobalt-free cation-disordered rocksalt (DRX) cathodes are a promising class of materials for next-generation Li-ion batteries. Although they have high theoretical specific capacities (>300 mA h/g) and moderate operating voltages (~3.5 V vs Li/Li + ), DRX cathodes typically require a high carbon content (up to 30 wt %) to fully utilize the active material which has a detrimental impact on cell-level energy density. To assess pathways to reduce the electrode’s carbon content, the present study investigates how the carbon’s microstructure and loading (10–20 wt %) influence the performance of DRX cathodes with the nominal composition Li 1.2 Mn 0.5 Ti 0.3 O 1.9 F 0.1 . While electrodes prepared with conventional disordered carbon additives (C65 and ketjenblack) exhibit rapid capacity fade due to an unstable cathode/electrolyte interface, DRX cathodes containing 10 wt % graphite show superior cycling performance (e.g., reversible capacities ~260 mA h/g with 85% capacity retention after 50 cycles) and rate capability (~135 mA h/g at 1000 mA/g). Furthermore, a suite of characterization tools was employed to evaluate the performance differences among these composite electrodes. Overall, these results indicate that the superior performance of the graphite-based cathodes is largely attributed to the: (i) formation of a uniform graphitic coating on DRX particles which protects the surface from parasitic reactions at high states of charge and (ii) homogeneous dispersion of the active material and carbon throughout the composite cathode which provides a robust electronically conductive network that can withstand repeated charge–discharge cycles. Overall, this study provides key scientific insights on how the carbon microstructure and electrode processing influence the performance of DRX cathodes. Based on these results, exploration of alternative routes to apply graphitic coatings is recommended to further optimize the material performance.

25 ENERGY STORAGE↗
DOE OSTI2025

Stable Cycling of Sodium All‐Solid‐State Batteries with High‐Capacity Cathode Presodiation

Sodium all-solid-state batteries (NaSSBs) with an alloy-type anode (e.g., Sn and Sb) offer superior capacity and energy density compared to hard carbon anode. However, the irreversible loss of Na + at the alloy anode during the initial cycle results in diminished capacity and stability, impairing full-cell performance. Here, this study presents an easy-to-implement cathode presodiation strategy by employing a Na-rich material to address these challenges. Leveraging the high theoretical capacity and suitable voltage window, Na 2 S is chosen as the Na donor, which is activated by creating a mixed electron-ion conducting network, delivering a high capacity of 511.7 mAh g −1 . By adding a small amount (i.e., 3 wt.%) of Na 2 S to the cathode composite, a NaCrO 2 || Sn full cell demonstrated capacity improvement from 90.8 to 118.2 mAh g −1 (based on cathode mass). The capacity-balanced full cell can thus cycle to more than 300 times with >90% capacity retention. This work provides a practical solution to enhance the full-cell performance and advance the transformation from half-cell to full-cell applications of NaSSBs.

25 - ENERGY STORAGE↗
NASA NTRSDate not supplied

Design Considerations for Practical Li-S Batteries for Electric Aviation

The development of high-energy, high-safety, and high-power batteries beyond electric automotive standards is critical for future electric aviation applications. Non-volatile solid-state electrolytes (SSE) offer many promising advantages over traditional flammable liquid electrolytes. Solid-state electrolytes may be an enabling technology for certain battery chemistries by preventing detrimental interactions with liquid electrolytes, for example prevention of the dissolution of intermediates in lithium-sulfur common in traditional liquid organic solvents. However, significant manufacturing challenges must be overcome before the adoption of such technology. This research was conducted to identify processing techniques for producing solid-state battery components with practical dimensions and weights for enabling high specific energy cells. Traditional research has identified a range of very high theoretical ionic conductivities but are impractical due to their instability or inability to be manufactured. Electrolytes explored in this study were produced as sulfide-polymer composites with densified thicknesses below 40 micron using a tape-casting technique and thermoplastic elastomer binder. The combination of high chemical compatibility and flexibility produced robust films that had moderate impact on the ionic conductivity but was capable of dramatically reducing the parasitic mass. Despite minimal conductivity losses, films were produced 10-15 times thinner than comparable bulk powder electrolytes thus leading to overall lower film resistance. Conductivity is maintained above 0.2mS/cm for composite electrolytes. Through the analysis of materials based on their physical properties, such as density, practical cells can be designed. Based on this, low density sulfide-solid-state electrolytes are a promising candidate for achieving the energy and safety metrics for electric aviation, however, further optimization of cathode microstructure and composite processing will be required to achieve the high power metrics and will be the focus of further studies. Additionally, fabrication challenges arise when utilizing metallic lithium foil, due to its soft nature, as overflow and mechanical short circuit can occur on assembly which remains a challenge to overcome before metallic lithium anodes can be fully realized.

batteries↗
DOE OSTI2022

Transition Metal Dissolution Mechanisms and Impacts on Electronic Conductivity in Composite LiNi 0.5 Mn 1.5 O 4 Cathode Films

The high-voltage LiNi 0.5 Mn 1.5 O 4 (LNMO) spinel cathode material offers high energy density storage capabilities without the use of costly Co that is prevalent in other Li-ion battery chemistries (e.g., LiNi x Mn y Co z O 2 (NMC)). Unfortunately, LNMO-containing batteries suffer from poor cycling performance because of the intrinsically coupled processes of electrolyte oxidation and transition metal dissolution that occurs at high voltage. In this work, we use operando electron paramagnetic resonance (EPR) and nuclear magnetic resonance (NMR) spectroscopies to demonstrate that transition metal dissolution in LNMO is tightly coupled to HF formation (and thus, electrolyte oxidation reactions as detected with operando and in situ solution NMR), indicative of an acid-driven disproportionation reaction that occurs during delithiation (i.e., battery charging). Leveraging the temporal resolution (s-min) of magnetic resonance, we find that the LNMO particles accelerate the rate of LiPF 6 decomposition and subsequent Mn 2+ dissolution, possibly due to the acidic nature of terminal Mn-OH groups. X-ray photoemission electron microscopy (XPEEM) provides surface-sensitive and localized X-ray absorption spectroscopy (XAS) measurements, in addition to X-ray photoelectron spectroscopy (XPS), that indicate disproportionation is enabled by surface reconstruction upon charging, which leads to surface Mn 3+ sites on the LNMO particle surface that can disproportionate into Mn 2+ (dissolved) and Mn 4+ (s) . During discharge of the battery, we observe high quantities of metal fluorides (in particular, MnF 2 ) in the cathode electrolyte interphase (CEI) on LNMO as well as the conductive carbon additives in the composite. Electronic conductivity measurements indicate that the MnF 2 decreases film conductivity by threefold compared to LiF, suggesting that this CEI component may impede both the ionic and electronic properties of the cathode. Ultimately, to prevent transition metal dissolution and the associated side reactions in spinel-type cathodes (particularly those that operate at high voltages like LNMO), the use of electrolytes that offer improved anodic stability and prevent acid byproducts will likely be necessary.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Cycling of block copolymer composites with lithium-conducting ceramic nanoparticles

Solid polymer and perovskite-type ceramic electrolytes have both shown promise in advancing solid-state lithium metal batteries. Despite their favorable interfacial stability against lithium metal, polymer electrolytes face issues due to their low ionic conductivity and poor mechanical strength. Highly conductive and mechanically robust ceramics, on the other hand, cannot physically remain in contact with redox-active particles that expand and contract during charge-discharge cycles unless excessive pressures are used. To overcome the disadvantages of each material, polymer-ceramic composites can be formed; however, depletion interactions will always lead to aggregation of the ceramic particles if a homopolymer above its melting temperature is used. In this study, we incorporate Li 0.33 La 0.56 TiO 3 (LLTO) nanoparticles into a block copolymer, polystyrene- b -poly (ethylene oxide) (SEO), to develop a polymer-composite electrolyte (SEO-LLTO). TEMs of the same nanoparticles in polyethylene oxide (PEO) show highly aggregated particles whereas a significant fraction of the nanoparticles are dispersed within the PEO-rich lamellae of the SEO-LLTO electrolyte. We use synchrotron hard x-ray microtomography to study the cell failure and interfacial stability of SEO-LLTO in cycled lithium-lithium symmetric cells. Three-dimensional tomograms reveal the formation of large globular lithium structures in the vicinity of the LLTO aggregates. Encasing the SEO-LLTO between layers of SEO to form a “sandwich” electrolyte, we prevent direct contact of LLTO with lithium metal, which allows for the passage of seven-fold higher current densities without signatures of lithium deposition around LLTO. We posit that eliminating particle clustering and direct contact of LLTO and lithium metal through dry processing techniques is crucial to enabling composite electrolytes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Critical role of structural order in bipolar redox-active molecules for organic redox flow batteries

Bipolar redox-active molecules (BRMs) have been suggested as a means to address crossover related issues in all-organic redox flow batteries (RFBs). In such species, electron donors (anolytes) and electron acceptors (catholytes) are linked by a chain, and the same chemical composition is used in both anode and cathode compartments to reduce chemical gradients and unbalanced ion transport. The resultant RFBs resemble the aqueous vanadium RFBs, but offer greater design flexibility and potentially more favorable electrochemical and physicochemical properties. Yet the complex trade-offs in these properties have been a complication. Here we developed a fundamental rubric to uncover the likely origins in the performance metrics of these BRMs that are salient for their use in RFBs. Methylene linked phenothiazine and phthalimide moieties were employed as model BRMs and variations in their properties and molecular conformations were evaluated by systematically varying the methylene linker. Our results revealed that even minimalistic changes in the linker length resulted in dramatic oscillations in the solubility and stability. Using crystallography, quantum chemistry, and molecular dynamics, we clarify that the seemingly fluctuating behavior is due to (1) the inter- and intra-molecular charge transfer between the donor and acceptor through bond or/and through space; (2) the formation of distinctive packing/clustering motifs. Both interactions are strongly dependent on the molecular conformation. As these structural factors modify the electronic structure of both electroactive functional groups and do not change monotonically, the structure–property response in BRMs is often complex. Finally, accordingly, these behaviors need to be taken into account in developing BRMs and knowledge of these structural factors will allow the more rational design of BRMs for grid-scale energy storage.

25 ENERGY STORAGE↗
DOE OSTI2021

High-performance ammonia oxidation catalysts for anion-exchange membrane direct ammonia fuel cells

Low-temperature direct ammonia fuel cells (DAFCs) use carbon-neutral ammonia as a fuel, which has attracted increasing attention recently due to ammonia's low source-to-tank energy cost, easy transport and storage, and wide availability. However, current DAFC technologies are greatly limited by the kinetically sluggish ammonia oxidation reaction (AOR) at the anode. Herein, we report an AOR catalyst, in which ternary PtIrZn nanoparticles with an average size of 2.3 ± 0.2 nm were highly dispersed on a binary composite support comprising cerium oxide (CeO 2 ) and zeolitic imidazolate framework-8 (ZIF-8)-derived carbon (PtIrZn/CeO 2 -ZIF-8) through a sonochemical-assisted synthesis method. Additionally, the PtIrZn alloy, with the aid of abundant OH ad provided by CeO 2 and uniform particle dispersibility contributed by porous ZIF-8 carbon (surface area: ~600 m 2 g -1 ), has shown highly efficient catalytic activity for the AOR in alkaline media, superior to that of commercial PtIr/C. The rotating disk electrode (RDE) results indicate a lower onset potential (0.35 vs. 0.43 V), relative to the reversible hydrogen electrode at room temperature, and a decreased activation energy (~36.7 vs. 50.8 kJ mol -1 ) relative to the PtIr/C catalyst. Notably, the PtIrZn/CeO 2 -ZIF-8 catalyst was assembled with a high-performance hydroxide anion-exchange membrane to fabricate an alkaline DAFC, reaching a peak power density of 91 mW cm -2 . Unlike in aqueous electrolytes, supports play a critical role in improving uniform ionomer distribution and mass transport in the anode. PtIrZn nanoparticles on silicon dioxide (SiO 2 ) integrated with carboxyl-functionalized carbon nanotubes (CNT–COOH) were further studied as the anode in a DAFC. A significantly enhanced peak power density of 314 mW cm -2 was achieved. Density functional theory calculations elucidated that Zn atoms in the PtIr alloy can reduce the theoretical limiting potential of *NH 2 dehydrogenation to *NH by ~0.1 V, which can be attributed to a Zn-modulated upshift of the Pt–Ir d-band that facilitates the N–H bond breakage.

25 ENERGY STORAGE↗
DOE OSTI2022

Lepidocrocite Titanate–Graphene Composites for Sodium-Ion Batteries

To overcome electronic transport issues of layered titanates in sodium-ion batteries, we have designed and synthesized composites of lepidocrocite titanates with reduced graphene oxide through a solution-based self-assembly approach. The parent lepidocrocite titanate (K 0.8 [Ti 1.73 Li 0.27 ]O 4 ) was exfoliated by a soft-chemical approach and mechanical shaking. Exfoliated layered titania sheets (LTO) were then combined with reduced graphene oxide (rGO) layers to assemble into composites through flocculation. Countercations (i.e., Mg 2+ ) were used for the self-assembly of negatively charged titania and rGO nanosheets via flocculation. The carbon content in the composites was tuned from 1 to 17% by changing the ratio of titania and rGO sheets in the mixed colloidal suspensions. Electrodes were processed with as-prepared LTO-rGO composites without any carbon additives and tested in sodium half-cell configurations. Mg + -coagulated LTO-rGO composite electrodes deliver higher capacities than electrodes prepared with coagulated titania sheets and 10% acetylene black in sodium half-cells and display good capacity retention after 50 cycles. Electrochemical impedance spectroscopy results indicate lower charge transfer resistance for LTO-14.5%rGO composites than that of coagulated titania sheets with 10% acetylene black. A power law analysis of cells containing the composites indicate a hybrid mechanism consisting of both surface and diffusional processes. A comparison with a similar system, that of dopamine-derived LTO-C heterostructures, reveal significant differences. While capacities showed a strong dependence on carbon content for the dopamine-derived materials, this was not true for the LTO-rGO composites. Instead, the highest capacity was obtained for the 14.5% rGO sample, with a lower value obtained for the 17% rGO sample. A greater proportion of the redox processes were surface rather than diffusional in nature for the LTO-rGO composites as well.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Probing Electrochemical Mg-Ion Activity in MgCr 2– x V x O 4 Spinel Oxides

Mg migration in oxide spinels is impeded by strong affinity between divalent Mg and oxygen, suggesting a necessity of exploring new chemistry of solid lattices for functional Mg-ion electrode materials. Cationic mobility with a suitable activation energy in Cr spinels is Tn. evidenced by theoretical and experimental results, while redox potentials of V are appropriate to operate with currently limited candidates of '''c" nonaqueous electrolytes. By controlling the structure, composition, and complexity, a largely solid-solution MgCrVO 4 spinel was synthesized, which, unlike nanocornposites, can bring together the advantages of each transition metal in the lattice. The spinel was successfully synthesized by a simple solid-state reaction with minor inactive Cr- or V-rich components, which was confirmed via 25 Mg MAS NMR and high-resolution X-ray diffraction analyses. A thermally and anodically stable Mg(TPFA) 2 /triglyme electrolyte was utilized for high-temperature electrochemistry and lowering kinetic barriers at and across interfaces so as to observe intercalation behavior of Mg in the designed lattice. Multimodal characterization confirmed an apparent bulk demagnesiation from MgCrVO 4 with partial reversibility by probing evolution of the local and long-range structure as well as vanadium and chromium electronic states within the lattice. Furthermore, characterization experiments also provided a direct evidence for (de)intercalation reactions that occurred without any major competitive conversion reactions or insertion of protons into the lattice, except for the formation of a surface rock salt phase upon charge. These findings in Mg-ion activity expand opportunities to design Mg spinel oxide materials while highlighting the need to identify the origins of reversibility challenges due to, but not limited to, phase stability, particularly for the charged states, barriers at the interface, electrolyte stabilities, and desolvation phenomena, collectively hindering practical use as cathode materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗