Results for “completely positive” — Page 13

NASA NTRS1972

GEODYN programmer's guide, volume 2, part 2

A computer program for executive control routine for orbit integration of artificial satellites is presented. At the beginning of each arc, the program initiates required constants as well as the variational partials at epoch. If epoch needs to be reset to a previous time, the program negates the stepsize, and calls for integration backward to the desired time. After backward integration is completed, the program resets the stepsize to the proper positive quantity.

Mullins, N. E.↗

NASA NTRS1981

Orbit improvement of the satellites of the outer planets

Data reduced from 127 plates showing Jupiter's and Saturn's satellites in the interval 1972 to 1974 are available on computer cards in the form of (O-C) residuals. Initial orbit calculations and several later orbit improvements for Jupiter XIII (Leda) culminated in an extended ephemeris for Leda to the year 2000. The possible existence of several small satellites just outside Saturns rings was predicted. De Sitter's incomplete theory for the motion of the Galilean satellites was reviewed and an outline for a revised, complete theory was developed. Observations of nearly 100 relative positions of the Galilean satellite with a mean accuracy of about 100 km (0.03 arc sec) were used to improve Sampson's theory for these satellites. Results were published on (1) a long term upper limit to Jupiter's orbital eccentricity; (2) deviation of an accurate modern value of the ellipticity of Uranus from balloon-borne images and consequent evaluation of the planet's rotation rate; and (3) identification of features in Saturn's rings as produced by heretofore undetected tesseral harmonics of Saturn's gravitational field.

Aksnes, K.↗

NASA NTRS1984

A search for Earth-crossing asteroids, supplement

The ground based electro-optical deep space surveillance program involves a network of computer controlled 40 inch 1m telescopes equipped with large format, low light level, television cameras of the intensified silicon diode array type which is to replace the Baker-Nunn photographic camera system for artificial satellite tracking. A prototype observatory was constructed where distant artificial satellites are discriminated from stars in real time on the basis of the satellites' proper motion. Hardware was modified and the technique was used to observe and search for minor planets. Asteroids are now routinely observed and searched. The complete observing cycle, including the 2"-3" measurement of position, requires about four minutes at present. The commonality of asteroids and artificial satellite observing, searching, data reduction, and orbital analysis is stressed. Improvements to the hardware and software as well as operational techniques are considered.

Taff, L. G.↗

NASA NTRS1986

Differential Very Long Baseline Interferometry for 50 nanoradian deep space navigation - Results from quasar pair experiments

Deep space tracking experiments completed at JPL have demonstrated a 50-nanoradian angular positioning accuracy with wideband differential Very Long Baseline Interferometry (delta VLBI). This meets the stringent navigation requirements of NASA's Galileo mission, scheduled for launch in May 1986 and for encounter with Jupiter in December 1988. Pairs of extragalactic radio sources (quasars) with well-known coordinates were used to simulate deep space navigation passes in which quasar-spacecraft pairs are observed. This paper discusses the accuracy of the delta VLBI technique and how it is affected by source separations, source elevations, source strengths, solar plasma and ionosphere. Several observation strategies are discussed and one is shown to be especially effective in minimizing these major error sources.

Trinkle, B. K.↗

NASA NTRS1987

Failure analysis of a 3.5 inch, 50 ampere-hour nickel-hydrogen cell

The 3.5 inch, 50 ampere-hour nickel-hydrogen cell was on a Low Earth Orbit (LEO) test regime and was being cycled at 10 C and 60 percent depth of discharge. At cycle number 511 the Automatic Control and Data Acquisition System (ACDAS) terminated the test when the end of discharge voltage dropped below the 1.00 volt cutoff. Upon removal of the stack assembly from the pressure vessel, portions of the zircar separator were found to be completely missing. Upon further examination portions of both the positive and negative plates were found to be missing from its substrate and several gas screens were damaged due to excessive heat which caused fusing. The postulated cause of failure is free electrolyte in the cell which caused oxygen channelization resulting in localized recombination which degraded the stack components.

Fuhr, Kenneth H.↗

NASA NTRS1991

Control of a flexible beam using fuzzy logic

The goal of this project, funded under the NASA Summer Faculty Fellowship program, was to evaluate control methods utilizing fuzzy logic for applicability to control of flexible structures. This was done by applying these methods to control of the Control Structures Interaction Suitcase Demonstrator developed at Marshall Space Flight Center. The CSI Suitcase Demonstrator is a flexible beam, mounted at one end with springs and bearing, and with a single actuator capable of rotating the beam about a pin at the fixed end. The control objective is to return the tip of the free end to a zero error position (from a nonzero initial condition). It is neither completely controllable nor completely observable. Fuzzy logic control was demonstrated to successfully control the system and to exhibit desirable robustness properties compared to conventional control.

Mccullough, Claire L.↗

NASA NTRS1991

Higher-order neural network software for distortion invariant object recognition

The state-of-the-art in pattern recognition for such applications as automatic target recognition and industrial robotic vision relies on digital image processing. We present a higher-order neural network model and software which performs the complete feature extraction-pattern classification paradigm required for automatic pattern recognition. Using a third-order neural network, we demonstrate complete, 100 percent accurate invariance to distortions of scale, position, and in-plate rotation. In a higher-order neural network, feature extraction is built into the network, and does not have to be learned. Only the relatively simple classification step must be learned. This is key to achieving very rapid training. The training set is much smaller than with standard neural network software because the higher-order network only has to be shown one view of each object to be learned, not every possible view. The software and graphical user interface run on any Sun workstation. Results of the use of the neural software in autonomous robotic vision systems are presented. Such a system could have extensive application in robotic manufacturing.

Reid, Max B.↗

NASA NTRS1937

Aerodynamic Characteristics of NACA 23012 and 23021 Airfoils with 20-Percent-chord External-Airfoil Flaps of NACA 23012 Section

Report presents the results of an investigation of the general aerodynamic characteristics of the NACA 23012 and 23021 airfoils, each equipped with a 0.20c external flap of NACA 23012 section. The tests were made in the NACA 7 by 10-foot and variable-density wind tunnels and covered a range of Reynolds numbers that included values corresponding to those for landing conditions of a wide range of airplanes. Besides a determination of the variation of lift and drag characteristics with position of the flap relative to the main airfoil, complete aerodynamic characteristics of the airfoil-flap combination with a flap hinge axis selected to give small hinge moments were measured in the two tunnels. Some measurements of air loads on the flap itself in the presence of the wing were made in the 7 by 10-foot wind tunnel.

Platt, Robert C↗

NASA NTRS1940

Preliminary wind-tunnel investigation of an NACA 23012 airfoil with various arrangements of venetian-blind flaps

Report presents the results of an investigation made in the NACA 7 by 10-foot wind tunnel of a large-chord NACA 23012 airfoil with several arrangements of venetian-blind flaps to determine the aerodynamic section characteristics as affected by the over-all flap chord, the chords of the slats used to form the flap, the slat spacing, the number of slats and the position of the flap with respect to the wing. Complete section data are given in the form of graphs for all the combinations tested.

Wenzinger, Carl J↗

NASA NTRS1961

Analysis of Effects of Interceptor Roll Performance and Maneuverability on Success of Collision-Course Attack

An attempt has been made to determine the importance of rolling performance and other factors in the design of an interceptor which uses collision-course tactics. A graphical method is presented for simple visualization of attack situations. By means of diagrams showing vectoring limits, that is, the ranges of interceptor position and heading from which attacks may be successfully completed, the relative importance of rolling performance and normal-acceleration capability in determining the success of attacks is illustrated. The results indicate that the reduction in success of attacks due to reduced rolling performance (within the limits generally acceptable from the pilots' standpoint) is very small, whereas the benefits due to substantially increasing the normal-acceleration capability are large. Additional brief analyses show that the optimum speed for initiating a head-on attack is often that corresponding to the upper left-hand corner of the V-g diagram. In these cases, increasing speed beyond this point for given values of normal acceleration and radar range rapidly decreases the width of the region from which successful attacks can be initiated. On the other hand, if the radar range is increased with a variation somewhere between the first and second power of the interceptor speed, the linear dimensions of the region from which successful attacks can be initiated vary as the square of the interceptor speed.

Phillips, William H.↗

NASA NTRS2003

Modeling and Visualizing Uncertainty in Continuous Variables Predicted using Remotely Sensed Data

The use of remotely sensed images to map continuous biophysical variables, such as those related to terrestrial vegetation amount, sea surface temperature, and many other targets of NASA s Earth Observing System (EOS), includes variable, parametric, positional, spatial support and structural sources of uncertainty. A complete description of uncertainty will lead to a probability distribution at each location, allowing the exploration of the spatial dimension of uncertainty, that is, where the field is not well quantified. To achieve this purpose, convenient visualization tools are required. We have produced such a tool, called PDFVis, that facilitates the display of probability density functions (pdfs) on a per-grid-cell basis. The density estimate from Monte-Carlo generated realizations is interactively displayed as well as parametric and non-parametric summaries of the pdf field (such as mean, median, quartiles, standard deviation, number of modes, and locations of modes). Shaded surface renderings of pdfs along a transect can also be projected onto a plane. This tool will become more useful as richer descriptions of spatial uncertainty become available.

Dungan, Jennifer L.↗

NASA NTRS2014

Access to Mars from Earth-Moon Libration Point Orbits:

This investigation is focused specifically on transfers from Earth-Moon L(sub 1)/L(sub 2) libration point orbits to Mars. Initially, the analysis is based in the circular restricted three-body problem to utilize the framework of the invariant manifolds. Various departure scenarios are compared, including arcs that leverage manifolds associated with the Sun-Earth L(sub 2) orbits as well as non-manifold trajectories. For the manifold options, ballistic transfers from Earth-Moon L(sub 2) libration point orbits to Sun-Earth L(sub 1)/L(sub 2) halo orbits are first computed. This autonomous procedure applies to both departure and arrival between the Earth-Moon and Sun-Earth systems. Departure times in the lunar cycle, amplitudes and types of libration point orbits, manifold selection, and the orientation/location of the surface of section all contribute to produce a variety of options. As the destination planet, the ephemeris position for Mars is employed throughout the analysis. The complete transfer is transitioned to the ephemeris model after the initial design phase. Results for multiple departure/arrival scenarios are compared.

Dynamical Systems↗

NASA NTRS2016

Experimenting Galileo on Board the International Space Station

The SCaN Testbed is an advanced integrated communications system and laboratory facility installed on the International Space Station (ISS) in 2012. The testbed incorporates a set of new generation of Software Defined Radio (SDR) technologies intended to allow researchers to develop, test, and demonstrate new communications, networking, and navigation capabilities in the actual environment of space. Qascom, in cooperation with ESA and NASA, is designing a Software Defined Radio GalileoGPS Receiver capable to provide accurate positioning and timing to be installed on the ISS SCaN Testbed. The GalileoGPS waveform will be operated in the JPL SDR that is constituted by several hardware components that can be used for experimentations in L-Band and S-Band. The JPL SDR includes an L-Band Dorne Margolin antenna mounted onto a choke ring. The antenna is connected to a radio front end capable to provide one bit samples for the three GNSS frequencies (L1, L2 and L5) at 38 MHz, exploiting the subharmonic sampling. The baseband processing is then performed by an ATMEL AT697 processor (100 MIPS) and two Virtex 2 FPGAs. The JPL SDR supports the STRS (Space Telecommunications Radio System) that provides common waveform software interfaces, methods of instantiation, operation, and testing among different compliant hardware and software products. The standard foresees the development of applications that are modular, portable, reconfigurable, and reusable. The developed waveform uses the STRS infrastructure-provided application program interfaces (APIs) and services to load, verify, execute, change parameters, terminate, or unload an application. The project is divided in three main phases. 1)Design and Development of the GalileoGPS waveform for the SCaN Testbed starting from Qascom existing GNSS SDR receiver. The baseline design is limited to the implementation of the single frequency Galileo and GPS L1E1 receiver even if as part of the activity it will be to assess the feasibility of a dual frequency implementation (L1E1+L5E5a) in the same SDR platform.2)Qualification and test the GalileoGPS waveform using ground systems available at the NASA Glenn Research Center. Experimenters can have access to two SCaN Testbed ground based systems for development and verification: the Experimenter Development System (EDS) that is intended to provide initial opportunity for software testing and basic functional validation and the Ground Integration Unit (GIU) that is a high fidelity version of the SCaN Testbed flight system and is therefore used for more controlled final development testing and verification testing.3)Perform in-orbit validation and experimentation: The experimentation phase will consists on the collection of raw measurements (pseudorange, Carrier phase, CN0) in space, assessment on the quality of the measurements and the receiver performances in terms of signal acquisition, tracking, etc. Finally computation of positioning in space (Position, Velocity and time) and assessment of its performance.(Complete abstract in attached document).

GPS↗

NASA NTRS2016

Experimenting Galileo on Board the International Space Station

The SCaN Testbed is an advanced integrated communications system and laboratory facility installed on the International Space Station (ISS) in 2012. The testbed incorporates a set of new generation of Software Defined Radio (SDR) technologies intended to allow researchers to develop, test, and demonstrate new communications, networking, and navigation capabilities in the actual environment of space. Qascom, in cooperation with ESA and NASA, is designing a Software Defined Radio GalileoGPS Receiver capable to provide accurate positioning and timing to be installed on the ISS SCaN Testbed. The GalileoGPS waveform will be operated in the JPL SDR that is constituted by several hardware components that can be used for experimentations in L-Band and S-Band. The JPL SDR includes an L-Band Dorne Margolin antenna mounted onto a choke ring. The antenna is connected to a radio front end capable to provide one bit samples for the three GNSS frequencies (L1, L2 and L5) at 38 MHz, exploiting the subharmonic sampling. The baseband processing is then performed by an ATMEL AT697 processor (100 MIPS) and two Virtex 2 FPGAs. The JPL SDR supports the STRS (Space Telecommunications Radio System) that provides common waveform software interfaces, methods of instantiation, operation, and testing among different compliant hardware and software products. The standard foresees the development of applications that are modular, portable, reconfigurable, and reusable. The developed waveform uses the STRS infrastructure-provided application program interfaces (APIs) and services to load, verify, execute, change parameters, terminate, or unload an application. The project is divided in three main phases. 1)Design and Development of the GalileoGPS waveform for the SCaN Testbed starting from Qascom existing GNSS SDR receiver. The baseline design is limited to the implementation of the single frequency Galileo and GPS L1E1 receiver even if as part of the activity it will be to assess the feasibility of a dual frequency implementation (L1E1+L5E5a) in the same SDR platform.2)Qualification and test the GalileoGPS waveform using ground systems available at the NASA Glenn Research Center. Experimenters can have access to two SCaN Testbed ground based systems for development and verification: the Experimenter Development System (EDS) that is intended to provide initial opportunity for software testing and basic functional validation and the Ground Integration Unit (GIU) that is a high fidelity version of the SCaN Testbed flight system and is therefore used for more controlled final development testing and verification testing.3)Perform in-orbit validation and experimentation: The experimentation phase will consists on the collection of raw measurements (pseudorange, Carrier phase, CN0) in space, assessment on the quality of the measurements and the receiver performances in terms of signal acquisition, tracking, etc. Finally computation of positioning in space (Position, Velocity and time) and assessment of its performance.(Complete abstract in attached document).

Galileo↗

NASA NTRS2016

Approach-Phase Precision Landing with Hazard Relative Navigation: Terrestrial Test Campaign Results of the Morpheus/ALHAT Project

The Morpheus Project began in late 2009 as an ambitious e ort code-named Project M to integrate three ongoing multi-center NASA technology developments: humanoid robotics, liquid oxygen/liquid methane (LOX/LCH4) propulsion and Autonomous Precision Landing and Hazard Avoidance Technology (ALHAT) into a single engineering demonstration mission to be own to the Moon by 2013. The humanoid robot e ort was redirected to a deploy- ment of Robonaut 2 on the International Space Station in February of 2011 while Morpheus continued as a terrestrial eld test project integrating the existing ALHAT Project's tech- nologies into a sub-orbital ight system using the world's rst LOX/LCH4 main propulsion and reaction control system fed from the same blowdown tanks. A series of 33 tethered tests with the Morpheus 1.0 vehicle and Morpheus 1.5 vehicle were conducted from April 2011 - December 2013 before successful, sustained free ights with the primary Vertical Testbed (VTB) navigation con guration began with Free Flight 3 on December 10, 2013. Over the course of the following 12 free ights and 3 tethered ights, components of the ALHAT navigation system were integrated into the Morpheus vehicle, operations, and ight control loop. The ALHAT navigation system was integrated and run concurrently with the VTB navigation system as a reference and fail-safe option in ight (see touchdown position esti- mate comparisons in Fig. 1). Flight testing completed with Free Flight 15 on December 15, 2014 with a completely autonomous Hazard Detection and Avoidance (HDA), integration of surface relative and Hazard Relative Navigation (HRN) measurements into the onboard dual-state inertial estimator Kalman lter software, and landing within 2 meters of the VTB GPS-based navigation solution at the safe landing site target. This paper describes the Mor- pheus joint VTB/ALHAT navigation architecture, the sensors utilized during the terrestrial ight campaign, issues resolved during testing, and the navigation results from the ight tests.

Crain, Timothy P.↗

NASA NTRSDate not supplied

Rebuilding the Habitable Zone from the Bottom Up

The idea of habitability has been useful for categorizing places where life might exist in the universe. Circumstellar habitable zones estimate whether rocky planets might harbor liquid surface water, geophysical and tidal habitable zones gauge places like icy moons. Combined with biological constraints of energy and element availability, habitability can be key for eliminating false positive biosignatures. But is there a more fundamental and complete way to talk about all of this? I’ll share a proposal for a concept of “computational zones” that digs deep into the fundamentals of what we think we know about life, and its relationship to matter, energy, and thermodynamics. With some simple examples I’ll also show how we can apply this to real (and imagined) questions, and what it suggests for the kinds of measurements and missions that could have the greatest astrobiological impact.

icy moons↗

DOE OSTI2023

Recent Hydrodynamic Modeling Enhancements in OpenFAST

To improve the hydrodynamic modeling capabilities of the offshore wind design and modeling tool OpenFAST, a restructuring of the HydroDyn hydrodynamics module was undertaken with several new features implemented. The generation of the wave field is now separated from HydroDyn into a new module called SeaState. Unlike previous versions of HydroDyn, which precomputed the wave kinematics at the undisplaced positions of the hydrodynamic nodes, the new SeaState module computes the complete time history of the wave field at the vertices of a user-defined wave grid. During the simulation, the wave kinematics at any point within the grid can be efficiently interpolated, allowing the strip-theory wave loads to be evaluated based on the wave kinematics at the displaced structure position. A phase correction was also implemented for the potential-flow wave-exciting loads to account for large structure displacements. Several wave-stretching methods were implemented for the strip-theory solution along with a wave-load redistribution method that ensures smooth variation of the nodal loads as the nodes of a discrete hydrodynamic mesh enter and exit the water. The load smoothing is included to avoid the excitation of unphysical high-frequency structural vibration during hydroelastic simulations. The MacCamy-Fuchs diffraction correction for the strip-theory solution and the capability to insert a constrained NewWave into extreme stochastic sea states with directional spreading were also added. The present article documents the formulations of the new improvements to HydroDyn with example applications and numerical results.

constrained wave↗

DOE OSTI2022

Recent Hydrodynamic Modeling Enhancements in OpenFAST: Preprint

To improve the hydrodynamic modeling capabilities of the offshore wind design and modeling tool OpenFAST, a restructuring of the HydroDyn hydrodynamics module was undertaken with several new features implemented. The generation of the wave field is now separated from HydroDyn into a new module called SeaState. Unlike previous versions of HydroDyn, which precomputed the wave kinematics at the undisplaced positions of the hydrodynamic nodes, the new SeaState module computes the complete time history of the wave field at the vertices of a user-defined wave grid. During the simulation, the wave kinematics at any point within the grid can be efficiently interpolated, allowing the strip-theory wave loads to be evaluated based on the wave kinematics at the displaced structure position. A phase correction was also implemented for the potential-flow wave-exciting loads to account for large structure displacements. Several wave-stretching methods were implemented for the strip-theory solution along with a wave-load redistribution method that ensures smooth variation of the nodal loads as the nodes of a discrete hydrodynamic mesh enter and exit the water. The load smoothing is included to avoid the excitation of unphysical high-frequency structural vibration during hydroelastic simulations. The MacCamy-Fuchs diffraction correction for the strip-theory solution and the capability to insert a constrained NewWave into extreme stochastic sea states with directional spreading were also added. The present article documents the formulations of the new improvements to HydroDyn with example applications and numerical results.

constrained wave↗