Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “calcination”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

CO{sub 2} capture from simulated syngas via cyclic carbonation/calcination for a naturally occurring limestone: pilot-plant testing

Experiments were performed using a dual fluidized bed reactor system, operated in a batch mode, in order to investigate the effects of steam and simulated syngas on CO{sub 2} capture and sorbent conversion efficiency for a naturally occurring Polish calcitic limestone. In addition, the effect of high partial pressures of CO{sub 2} on the calcination process was examined using either oxygen-enriched air or oxy-fuel combustion in the calciner. As expected, calcination under oxy-fuel conditions resulted in decreased carbonation conversion due primarily to particle sintering and pore pluggage. On average there was a decrease in carbonation conversion of approximately 36.5 and 33.4% for carbonation with steam and steam/simulated syngas, respectively, compared to similar experiments using oxygen-enriched air. However, during the carbonation of the limestone with steam present in the feed gas, it was observed that the high CO{sub 2} capture efficiency period was significantly extended compared to carbonation with only CO{sub 2} present. This resulted in increased CaO conversion from approximately 16.1 to 29.7% for the initial carbonation cycle. A further increase in carbonation conversion from 29.7 to 46.9%, was also observed when simulated syngas conditions (CO, H{sub 2}) were used in the carbonator. Analysis of the outlet gases also confirmed that the calcined limestone catalyzes the water gas shift reaction, which we believe results in enhanced CO{sub 2} concentration levels at the grain surfaces of the sorbent.

01 COAL, LIGNITE, AND PEAT↗

Colloidally Synthesized Monodisperse Rh Nanoparticles Supported on SBA-15 for Size- and Pretreatment-Dependent Studies of CO Oxidation

A particle size dependence for CO oxidation over rhodium nanoparticles of 1.9-11.3 nm has been investigated and determined to be modified by the existence of the capping agent poly(vinylpyrrolidone) (PVP). The particles were prepared using a polyol reduction procedure with PVP as the capping agent. The Rh nanoparticles were subsequently supported on SBA-15 during hydrothermal synthesis to produce Rh/SBA-15 supported catalysts for size-dependent catalytic studies. CO oxidation by O{sub 2} at 40 Torr CO and 100 Torr O{sub 2} was investigated over two series of Rh/SBA-15 catalysts: as-synthesized Rh/SBA-15 covering the full range of Rh sizes and the same set of catalysts after high temperature calcination and reduction. The turnover frequency at 443 K increases from 0.4 to 1.7 s{sup -1} as the particle size decreases from 11.3 to 1.9 nm for the as-synthesized catalysts. After calcination and reduction, the turnover frequency is between 0.1 and 0.4 s{sup -1} with no particle size dependence. The apparent activation energy for all catalysts is {approx}30 kcal mol{sup -1} and is independent of particle size and thermal treatment. Infrared spectroscopy of CO on the Rh nanoparticles indicates that the heat treatments used influence the mode of CO adsorption. As a result, the particle size dependence for CO oxidation is altered after calcination and reduction of the catalysts. CO adsorbs at two distinct bridge sites on as-synthesized Rh/SBA-15, attributable to metallic Rh(0) and oxidized Rh(I) bridge sites. After calcination and reduction, however, CO adsorbs only at Rh(0) atop sites. The change in adsorption geometry and oxidation activity may be attributable to the interaction between PVP and the Rh surface. This capping agent affect may open new possibilities for the tailoring of metal catalysts using solution nanoparticle synthesis methods.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Gas generation during waste treatment of acidic solutions from the dissolution of irradiated LEU targets for 99 Mo production

The goal of the Reduced Enrichment for Research and Test Reactors Program is to limit the use of high-enriched uranium (HEU) in research and test reactors by substituting low-enriched uranium (LEU) wherever possible. The work reported here documents our work to develop the calcining technologies and processes that will be needed for 99 Mo production using LEU foil targets and the Modified Cintichem Process. The primary concern with the conversion to LEU from HEU targets is that it would result in a five- to six-fold increase in the total uranium. This increase results in more liquid waste from the process. We have been working to minimize the increase in liquid waste and to minimize the impact of any change in liquid waste. Direct calcination of uranium-rich nitric acid solutions generates NO 2 gas and UO 3 solid. We have proposed two processes for treating the liquid waste from a Modified Cintichem Process with a LEU foil. One is an optimized direct calcination process that is similar to the process currently in use. The other is a uranyl oxalate precipitation process. The specific goal of the work reported here was to characterize and compare the chemical reactions that occur during these two processes. In particular, the amounts and compositions of the gaseous and solid products were of interest. A series of experiments was carried out to show the effects of temperature and the redox potential of the reaction atmosphere. The primary products of the direct calcination process were mixtures of U 3 O 8 and UO 3 solids and NO 2 gas. The primary products of the oxalate precipitation process were mixtures of U 3 O 8 and UO 2 solid and CO 2 gas. Higher temperature and a reducing atmosphere tended to favor quadrivalent over hexavalent uranium in the solid product. These data will help producers to decide between the two processes. In addition, the data can be used to design appropriate off-gas systems for pilot and production facilities.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Synthesis and textural evolution of alumina particles with mesoporous structures

Alumina particles with mesostructures were synthesized through a chemical precipitation method by using different inorganic aluminum salts followed by a heterogeneous azeotropic distillation and calcination process. The obtained mesoporous {gamma}-alumina particles were systematically characterized by the X-ray diffraction, transmission electron microscopy and nitrogen adsorption-desorption measurement. Effects of the aluminum salt counter anion, pH value and the azeotropic distillation process on the structural or textural evolution of alumina particles were investigated. It is found that Cl{sup -} in the reaction solution can restrain the textural evolution of the resultant precipitates into two-dimensional crystallized pseudoboehmite lamellae during the heterogeneous azeotropic distillation, and then transformed into {gamma}-Al{sub 2}O{sub 3} particles with mesostructures after further calcination at 1173 K, whereas coexisting SO{sub 4}{sup 2-} can promote above morphology evolution and then transformed into {gamma}-Al{sub 2}O{sub 3} nanofibers after calcination at 1173 K. Moreover nearly all materials retain relatively high specific surface areas larger than 100 m{sup 2} g{sup -1} even after calcinations at 1173 K. - Graphical abstract: Co-existing Cl{sup -} is beneficial for the formation of {gamma}-alumina nanoparticles with mesostructures during the precipitation process. Interparticle and intraparticle mesopores can be derived from acidic solution and near neutral solution, respectively.

36 MATERIALS SCIENCE↗

Influence of thermal treatment on structure and catalytic performance of ceria-zirconia supported copper oxide (CuO x /Ce y Zr 1-y O 2 ) catalysts for CO oxidation

Copper oxide (CuO x ) supported on ceria-zirconia (Ce y Zr 1-y O 2 , y = 1.0, 0.5, 0.0) catalysts were investigated to elucidate the effects of thermal treatment on their physicochemical properties and catalytic performance in carbon monoxide (CO) oxidation. Here, the catalysts were synthesized via a one-pot chemical vapor deposition (OP-CVD) method at 700˚C and 900˚C with controlled Cu loading. Characterization techniques, including synchrotron X-ray diffraction (S-XRD), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), inductively coupled plasma spectroscopy (ICP), and N 2 adsorption-desorption, were implemented to probe the crystalline structure, molecular and electronic structure, oxygen vacancies, specific surface area (SSA) and metal loading. CO oxidation was chosen as a model reaction to explore the structure-catalytic performance relationship. A ∼100% CO conversion was achieved at < 150˚C, particularly with the CuO x /CeO 2 catalyst calcined at 700˚C. In contrast, calcination at 900˚C caused a ∼90% decrease in SSA and a ∼24% increase in T 50 . Activity tests revealed that increasing ZrO 2 content lowered CO oxidation activity despite generating more defect sites. In-situ measurement of the 700 °C calcined samples revealed the presence of stable and unstable defects in CuO x /Ce 0.5 Zr 0.5 O 2 and CeO 2 respectively, which play a key role in the activity of the catalysts. The results highlight that catalytic performance is closely related to the SSA. Furthermore, an optimum calcination temperature favor significant oxygen vacancy formation with required CuO x -support interactions, enhancing redox properties and catalytic performance.

36 MATERIALS SCIENCE↗

Influence of Sm{sup 3+} ions on structural, optical and solar light driven photocatalytic activity of spinel MnFe{sub 2}O{sub 4} nanoparticles

In this article, co-precipitation method was used to produce a series of samarium substituted manganese ferrite nanoparticles, MnFe{sub 2−x}Sm{sub x}O{sub 4} (x = 0.0, 0.5, 1.0, 1.5, 2.0) with oleic acid as surfactant. The effect of Sm{sup 3+} substitution and calcination temperature on the MnFe{sub 2}O{sub 4} was explored. The MnFe{sub 2−x}Sm{sub x}O{sub 4} sample calcinated at 973 K induced an enhanced optical behaviour. The influence of Sm{sup 3+} ions on cationic distribution and optical properties of MnFe{sub 2}O{sub 4} were probed by various physicochemical techniques. The presence of secondary orthorhombic (SmFeO{sub 3}) phase with initial cubic phase was confirmed by doublet peak in the X-ray diffraction pattern. The particle size distribution of MnFe{sub 0.5}Sm{sub 1.5}O{sub 4} sample was about 40 nm from HRTEM. The visible light absorption ability extended as Sm content was increased up to x = 1.5 in MnFe{sub 2}O{sub 4}. At an optimum concentration of Sm as x = 1.5 in MnFe{sub 2}O{sub 4}, photocatalyst exhibited decrease in energy band gap (1.64 eV); as a result effective visible light driven photocatalytic activity was achieved than the pure MnFe{sub 2}O{sub 4}. The MnSm{sub 1.5}Fe{sub 0.5}O{sub 4} sample exhibits pronounced photodegradation towards Rose Bengal with in 50 min under direct sunlight illumination as energy input. The broad emission band is observed in the entire photoluminescence (PL) spectrum. Current study provides an excellent competency of rare earth substituted ferrite as a new class of photocatalyst and they found to be a beneficial in the field of environmental cleaning application. - Highlights: • MnSm{sub x}Fe{sub 2−x}O{sub 4} nanoparticles were synthesised by co-precipitation method. • The insertion of Sm{sup 3+} ion in the MnFe{sub 2}O{sub 4} spinel matrix shows an increase in lattice parameter. • The calcination temperature is sensitive knob for tuning the optical properties of the MnFe{sub 2−x}Sm{sub x}O{sub 4} photocatalyst. • The MnFe{sub 2−x}Sm{sub x}O{sub 4} calcinated at 973 K shows enhanced optical behaviour. • The composition MnFe{sub 0.5}Sm{sub 1.5}O{sub 4} showed substantial red shift in absorption edge with narrow band gap of 1.64 eV.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Microwave hydrothermal synthesis of nanoporous cobalt oxides and their gas sensing properties

Graphical abstract: Photographs taken at the field emission scanning electron microscope of (a) nanosheet-like Co{sub 3}O{sub 4}, (b) nanochain-like Co{sub 3}O{sub 4} and (c) nanoring-like Co{sub 3}O{sub 4}. Highlights: {yields} CO{sub 3}{sup 2-} acts as an inhibitor that affects the growth rates of precursors in different crystal directions. {yields} Nanosheet-like Co{sub 3}O{sub 4}, nanochain-like Co{sub 3}O{sub 4}, and nanoring-like Co{sub 3}O{sub 4} were obtained by microwave hydrothermal process under different precipitants and synthetic conditions. {yields} Specific surface area of nano Co{sub 3}O{sub 4} with various morphologies plays an important role in gas sensitivity to alcohol. -- Abstract: In this paper, the precursors were synthesized by microwave hydrothermal method using Co(NO{sub 3}){sub 2}.6H{sub 2}O as raw material, CO(NH{sub 2}){sub 2} and KOH as precipitants, respectively. The precursors and calcined products were characterized by XRD, FESEM, and BET-BJH. The results show that both constituent and synthetic condition can determine the products morphology. When using KOH as precipitant, hollow Co{sub 3}O{sub 4} nanorings were obtained whose precursor was synthesized at 140 {sup o}C for 3 h and calcined at 500 {sup o}C in air for 2 h. While using CO(NH){sub 2}, Co{sub 3}O{sub 4} like-nanochains were obtained whose precursor was synthesized at 110 {sup o}C for 1 h and calcined at 420 {sup o}C in air for 2 h, and Co{sub 3}O{sub 4} nanosheets were obtained while their precursor was synthesized at 140 {sup o}C for 3 h and calcined at 500 {sup o}C in air for 2 h. The sensitivity test of Co{sub 3}O{sub 4} to alcohol reveals that the hollow Co{sub 3}O{sub 4} nanorings show the best sensitivity, porous Co{sub 3}O{sub 4} like-nanochains are superior to that of the porous nanosheets.

36 MATERIALS SCIENCE↗

Fabrication of nano structural biphasic materials from phosphogypsum waste and their in vitro applications

Graphical abstract: (a) Schema of the process, (b) TEM of nano particles of biphasic materials and (c) SEM of post-immersion. - Highlights: • Ratio of HA and β-TCP phases were controlled by thermal treatment. • HA partially decomposed into β-TCP with other bioactive phases. • Calcined HA at 900 °C is the best for the bioactivity behavior. - Abstract: In this study, a novel process of preparing biphasic calcium phosphate (BCP) is proposed. Also its bioactivity for the utilization of the prepared BCP as a biomaterial is studied. A mixture of calcium hydroxyapatite (HAP) and tricalcium phosphate (β-TCP) could be obtained by thermal treatment of HAP which was previously prepared from phosphogypsum (PG) waste. The chemical and phase composition, morphology and particle size of prepared samples was characterized by X-ray diffraction (XRD), Infrared spectroscopy (IR), Scanning electron microscopy (SEM) and Transmission electron microscopy (TEM). The bioactivity was investigated by soaking of the calcined samples in simulated body fluid (SBF). Results confirmed that the calcination temperatures played an important role in the formation of calcium phosphate (CP) materials. XRD results indicated that HAP was partially decomposed into β-TCP. The in vitro data confirmed that the calcined HAP forming BCP besides other phases such as pyrophosphate and silica are bioactive materials. Therefore, BCP will be used as good biomaterials for medical applications.

36 MATERIALS SCIENCE↗

Iridium Atoms Bonded to Crystalline Powder MgO: Characterization by Imaging and Spectroscopy

Samples with low loadings of metals on well-defined supports provide some of the best opportunities to determine the metal–support structure and bonding. We illustrate methods for characterizing atomically dispersed heavy metals on metal oxide supports by aberration-corrected scanning transmission electron microscopy (STEM) complemented by fluorescence detection extended X-ray absorption fine structure and infrared spectroscopies. STEM images of Ir atoms derived from Ir(C 2 H 4 ) 2 (acac) (acac = acetylacetonato) on high-surface-area MgO powder were obtained with minimized electron beam damage by quickly recording images near where the focus had been established. The images show that iridium at a loading of 1.0 wt % on MgO calcined at 1073 K was atomically dispersed, populating much of the surface of the MgO particles, which had irregular shapes—consequently the Ir atoms were bonded at various sites to two or three surface O atoms. In contrast, MgO calcined at 1273 K consisted of almost perfectly cubic crystals, and Ir atoms at a loading of only 0.01 wt % on this nearly ideal support were anchored preferentially at edges and corners of the (100) faces and bonded to three surface O atoms. The latter results indicate a path forward for the determination of precise structures of atomically dispersed metals on crystalline metal oxide supports.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structure-Activity Relationships of Hydrothermally Aged Titania-Supported Vanadium-Tungsten Oxide Catalysts for SCR of NOx Emissions with NH3

Supported V2O5-WO3/TiO2 materials employed as selective catalytic reduction (SCR) catalysts for NOx emission control from power plants. Fresh SCR catalysts usually receive exposure to harsh treatments in industry to accelerate catalyst activation (calcination in air at 650oC) and catalyst aging (hydrothermal aging at 650oC) in a way that represents various points in the catalyst/product lifetime. The present study investigates the catalyst structural and chemical changes occurring during such harsh treatments. Three series of supported V2O5-WO3/TiO2 catalysts were prepared by incipient-wetness impregnation of aqueous ammonium metavanadate and metatungstate precursors. The catalysts were subsequently dried and calcined at 550oC in O2, 650oC in O2, and hydrothermal conditions (10% O2, 8% H2O, 7% CO2 and 75% N2) at 650oC. The resulting catalysts were physically characterized by numerous techniques (in situ Raman, in situ IR, in situ High Field-High Spinning solid-state 51V MAS NMR, in situ EPR, XRD, BET surface area and ICP) and chemically probed with adsorbed ammonia, SCR-TPSR, and the SCR reaction. The surface WOx sites on the TiO2 support behave as a textural promoter that stabilizes the TiO2 (anatase) phase from sintering and transforming to the undesirable crystalline TiO2 (rutile) phase that can lead to formation of a Ti1-xVxO2 (rutile) solid solution with reduced V4+ cations (~7-15%). The surface VOx sites are mostly oligomerized as surface V+5Ox sites (~50-85% oligomers) and the extent of oligomerization tends to increase with surface WOx coverage and calcination temperature. A major difference between the calcined and hydrothermally treated catalysts was the low concentration of surface NH3* species on Lewis acid sites for the hydrothermally treated catalysts, yet the SCR activity was almost comparable for both catalysts. This finding suggests that surface NH4+*, primarily associated with the surface VOx sites, are able to efficiently perform the SCR reaction. Given that multiple catalyst parameters were simultaneously varying during these treatments, it was difficult to correlate the SCR activity with any single catalyst parameter. A correlation, however, was found between the SCR TOF/activity and the sum of the surface NH3* and NH4+* species, which is dominated by the surface NH4+* species.

SCR, NO, NH3, catalyst, V2O5, WO3, TiO2, promotion↗

Comparison of different natural sorbents for removing CO{sub 2} from combustion gases, as studied in a bench-scale fluidized bed

The reaction of CO{sub 2} with porous particles of CaO for chicken eggshells, mussel shells, and limestone. The reaction is a promising way of removing CO{sub 2}, e.g., from the exhaust of a power station, so that a pure stream of CO{sub 2} can subsequently be produced for sequestration by calcining (roasting) the solid CaCO{sub 3}. The reverse of the reaction regenerates the sorbent, which can thus be used cyclically. The reaction were investigated using a small electrically heated bed of sand at about 750{degree}C, fluidized by N{sub 2}. Typically, a sample (about 2 g) of cleaned calcareous material (sieved to about 600 {mu}m) was added to the hot bed, and the CO{sub 2} produced was measured, while the material was fully calcined. Next, enough CO{sub 2} was added to the fluidizing N{sub 2} to raise (CO{sub 2}) to above the value for equilibrium; thus, the CaO was carbonated. This forward step is shown to exhibit an apparent final conversion, the carrying capacity of the sorbent, below unity. This carrying capacity reduces after several cycles of calcination and carbonation, because blockage of pores denies access of CO{sub 2} to part of the CaO. After several such cycles, particles were removed from the reactor, either in their partially carbonated or fully calcined states, for studies using gas adsorption analysis, X-ray diffraction, and mercury porosimetry. Interestingly, it was found for all three sorbents that the carrying capacity of CaO for CO{sub 2} degraded at a similar rate. The carrying capacity was roughly proportional to the volume of pores narrower than about 100 nm, as measured by Barrett-Joyner-Halenda (BJH) gas adsorption analysis. Evidently, these narrow pores contain both the surface area for CO{sub 2} to absorb and the empty volume to accommodate the product, CaCO{sub 3}. The resistance of eggshells to attrition was broadly comparable to that of Purbeck (U.K.) limestone. 24 refs., 8 figs., 2 tabs.

01 COAL, LIGNITE, AND PEAT↗

Elucidating the phase transformations and grain growth behavior of O3-type sodium-ion layered oxide cathode materials during high temperature synthesis

Understanding the formation mechanism of layered oxide cathodes via solid-state synthesis is imperative to achieving controllability over their materials properties and electrochemical behaviors. In this work, we investigate the phase and microstructure evolution during the synthesis of NaNi 1/3 Fe 1/3 Mn 1/3 O 2 , a model sodium-ion layered oxide cathode, using a combination of imaging, diffraction, and spectroscopic techniques. We unravel the synthetic mechanistic pathways involved in the high-temperature calcination reaction, as well as elaborate the synthesis-microstructure-performance relationship of this material. The formation of the final layered oxide phase involves a gradual transformation through a sodiated oxyhydroxide intermediate. During the reaction, the precursor dehydration reaction dominates at 250–550 °C, while the major sodiation reaction occurs at 550–850 °C. Alongside multiple stages of phase transformations, the final grain structure formation occurs through the continuous growth of the (003) and (104) facets. During the reaction, Mn acts as the charge-compensating element and exhibits depth-dependent characteristics. When the sodiation reaction dominates over dehydration, the reaction intermediates undergo gradual electronic structure changes with increasing temperature, as indicated by the spectral features of TM3d-O2p hybrid states. Calcination duration is also a critical parameter governing the microstructure, surface reactivity, phase fraction distribution and electrochemical performance of the material. The optimal calcination duration was determined to be 18 hours at 850 °C under the conditions evaluated here. Calcination beyond this duration was found to be detrimental to electrochemical performance due to Na and O loss and heterogeneous sodium distribution throughout the particles. Our work sheds light on the complex crystallographic-chemical-microstructural evolution of sodium ion layered oxide cathodes and provides insight into precisely tuning material properties which are intimately linked to battery performances.

25 ENERGY STORAGE↗

Use of Au@Void@TiO 2 yolk-shell nanostructures to probe the influence of oxide crystallinity on catalytic activity for low-temperature oxidations

A series of Au@Void@TiO 2 yolk-shell structures were synthesized and characterized, and their catalytic activity was tested for the oxidation of carbon monoxide. The target of this study was to evaluate the effects of (1) the crystallinity of the TiO 2 shell and (2) the presence of titanate phases. Transmission electron microscopy and X-ray diffraction data show that increasing calcination temperatures, from 850 to 1250 K, leads to the formation of larger titania crystallites. These crystallites are typically in the form of anatase, but some rutile is also made at high temperatures. The general yolk-shell nanostructures retain their basic characteristics upon calcination and upon treatment with HCl (used to remove the titanate phases), but a few structural and chemical changes do take place: (1) the void-space diameter is reduced by approximately 10% when going from T Calc = 850 K to T Calc = 1250 K, a change that is accompanied by a decrease in the surface area (estimated from N 2 adsorption-desorption isotherms); (2) the shell thickness remains unaffected by either calcination or HCl treatment; (3) the pore volume also remains approximately constant with increasing calcination temperature in the catalysts free of titanates but diminishes significantly in the samples with titanate phases; (4) the mesoporosity is minimal in all yolk-shell nanostructures but more noticeable with the pure TiO 2 shells; (5) the titanates have high Na content (measured by X-ray photoelectron spectroscopy), but that Na is fully removed upon treatment with HCl; (6) no Ti 3+ was detectable in any of the samples, but silica, together with C and (minor amounts of) N, was present in all; (7) all Au is in metallic form; (8) two temperature regimes were observed for the catalytic oxidation of CO, as reported for other similar samples in the past, an Arrhenius regime around or above room temperature, and a cryogenic range going to temperatures as low as 120 K; (9) the latter regime is only seen with the samples containing titanate phases; (10) the titanates seem to also aid in the oxidation at higher temperatures; and (11) in general, increasing titania crystallinity leads to a decrease the catalytic activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DEVELOPMENT OF CRYSTALLINE CERAMICS FOR IMMOBILIZATION OF ADVANCED FUEL CYCLE REPROCESSING WASTES

The Savannah River National Laboratory (SRNL) is developing crystalline ceramic waste forms to incorporate CS/LN/TM high Mo waste streams consisting of perovskite, hollandite, pyrochlore, zirconolite, and powellite phase assemblages. Simple raw materials, including Al{sub 2}O{sub 3}, CaO, and TiO{sub 2} were combined with simulated waste components to produce multiphase crystalline ceramics. Fiscal Year 2011 (FY11) activities included (i) expanding the compositional range by varying waste loading and fabrication of compositions rich in TiO{sub 2}, (ii) exploring the processing parameters of ceramics produced by the melt and crystallize process, (iii) synthesis and characterization of select individual phases of powellite and hollandite that are the target hosts for radionuclides of Mo, Cs, and Rb, and (iv) evaluating the durability and radiation stability of single and multi-phase ceramic waste forms. Two fabrication methods, including melting and crystallizing, and pressing and sintering, were used with the intent of studying phase evolution under various sintering conditions. An analysis of the XRD and SEM/EDS results indicates that the targeted crystalline phases of the FY11 compositions consisting of pyrochlore, perovskite, hollandite, zirconolite, and powellite were formed by both press and sinter and melt and crystallize processing methods. An evaluation of crystalline phase formation versus melt processing conditions revealed that hollandite, perovskite, zirconolite, and residual TiO{sub 2} phases formed regardless of cooling rate, demonstrating the robust nature of this process for crystalline phase development. The multiphase ceramic composition CSLNTM-06 demonstrated good resistance to proton beam irradiation. Electron irradiation studies on the single phase CaMoO{sub 4} (a component of the multiphase waste form) suggested that this material exhibits stability to 1000 years at anticipated self-irradiation doses (2 x 10{sup 10}-2 x 10{sup 11} Gy), but that its stability may be rate dependent, therefore limiting the activity of the waste for which it can be employed. Overall, these preliminary results indicate good radiation damage tolerance for the crystalline ceramic materials. The PCT results showed that, for all of the waste forms tested, the normalized release values for most of the elements measured, including all of the lanthanides and noble metals, were either very small or below the instrument detection limits. Elevated normalized release values were measured only for Cs, Mo, and Rb. It is difficult to draw further conclusions from these data until a benchmark material is developed for the PCT with this type of waste form. Calcined, simulated CS/LN/TM High Mo waste without additives had relatively low normalized release values for Cs, Mo, and Rb. A review of the chemical composition data for this sample showed that these elements were well retained after the calcination. Therefore, it will be useful to further characterize the calcined material to determine what form these elements are in after calcining. This, along with single phase studies on Cs containing crystal structures such as hollandite, should provide insight into the most ideal phases to incorporate these elements to produce a durable waste form.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Templated synthesis of nickel nanoparticles: Toward heterostructured nanocomposites for efficient hydrogen storage

The world is currently facing an energy and environmental crisis for which new technologies are needed. Development of cost-competitive materials for catalysis and hydrogen storage on-board motor vehicles is crucial to lead subsequent generations into a more sustainable and energy independent future. This thesis presents work toward the scalable synthesis of bimetallic heterostructures that can enable hydrogen to compete with carbonaceous fuels by meeting the necessary gravimetric and volumetric energy densities and by enhancing hydrogen sorption/desorption kinetics near ambient temperatures and pressures. Utilizing the well-known phenomenon of hydrogen spillover, these bimetallic heterostructures could work by lowering the activation energy for hydrogenation and dehydrogenation of metals. Herein, we report a novel method for the scalable synthesis of silica templated zero-valent nickel particles (Ni$\subset$ SiO 2 ) that hold promise for the synthesis of nickel nanorods for use in bimetallic heterostructures for hydrogen storage. Our synthesis proceeds by chemical reduction of a nickel-hydrazine complex with sodium borohydride followed by calcination under hydrogen gas to yield silica encapsulated nickel particles. Transmission electron microscopy and powder X-ray diffraction were used to characterize the general morphology of the resultant nanocapsules as well as the crystalline phases of the incorporated Ni 0 nanocrystals. The structures display strong magnetic behavior at room temperature and preliminary data suggests nickel particle size can be controlled by varying the amount of nickel precursor used in the synthesis. Calcination under different environments and TEM analysis provides evidence for an atomic migration mechanism of particle formation. Ni$\subset$SiO 2 nanocapsules were used as seeds to induce heterogeneous nucleation and subsequent growth within the nanocapsule via electroless nickel plating. Nickel nanoparticle growth occurs under high temperature alkaline conditions, however silica nanocapsule integrity is not maintained due to the incompatibility of silica with the growth conditions. Silica nanocapsule integrity is maintained under low temperature neutral conditions, but nickel particle growth is not observed. Through FTIR and UV/Vis analysis, we show the degree of crosslinking and condensation increases in calcined silica compared to as-synthesized silica. We propose the increased density of the silica nanocapsule hinders mass transfer of the bulky nickel precursor complex from solution and onto the surface of the “catalytic” zero-valent nickel seed within the nanocapsule cavity. Decreasing the density of the silica nanocapsule can be achieved through co-condensation of tetraethylorthosilicate with an alkyl functionalized silane followed by calcination to remove the organic component or by chemical etching in alkaline solution, but will not be addressed in this thesis.

08 HYDROGEN↗

LANL Response to SRS Requirement G-ESR-G-00035 Item 11 Bed Temperature Requirements, For the Addition of Direct Metal Oxidation Unit 3, Revision 0

Los Alamos National Laboratory has identified a number of plutonium-bearing materials that will be placed in storage in 3013 containers per requirements of DOE-STD-3013-2004, or DOE-STD-3013-2012 when it is implemented in the LANL contract. Before these items can be considered for storage at Savannah River Site, 20 points of agreement, described in Savannah River Site (SRS) document G-ESR-G-00035, Revision 1, must be documented and provided to SRS for review. These agreements include documentation that the requirements of the 3013 Standard are met and the storage facility’s safety envelope is not compromised. Point 11 of the 20 points is the requirement that material be stabilized at 950°C for a minimum of two hours prior to packaging. This report addresses the Point 11 requirement, describing the controls used during stabilization to ensure that the material is properly stabilized using a continuous process (Advanced Recovery and Integrated Extraction System [ARIES] direct metal oxidation [DMO] and recycle oxide calcination). These controls include verification of the furnace controller thermocouple profile and verification of the profiles for the calciner tube hot zone. This report is specific to Direct Metal Oxidation Unit 3 (DMO-3). The point 11 requirements for DMO-2 and muffle furnace oxidation are covered in reference. This report does not replace reference. The process and methodology used in this report are similar to that used for Direct Metal Oxidation Unit 2, or DMO-2, as documented in reference. This report documents the performance for ARIES DMO-3. The temperature on the outside of the calciner tube must be at least 1,032°C. The auger rotation rate set point will be dependent on the pitch of the installed auger. For an auger pitch of 1.297 in/rev the auger set point will be 0.0777 rpm or less, which allows for at least 132 minutes calcination time based on worst case conditions (i.e., lowest possible powder density at the lowest initial powder temperature, and under the least favorable heat transfer conditions, and with the least favorable auger pitch of the currently installed auger.) A new auger design may be used in future modifications of DMO-3 that has an auger pitch of 1.400 ± 0.025 inches which would change the required auger set point to 0.0707 rpm or less.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High-Energy X-ray Diffraction Microscopy for Nuclear Forensics FY2022 Project Report

Morphological information on nuclear material has been identified using visible light and scanning electron microscopy. These identify qualitative differences in particle morphology. Three-dimensional imaging of materials through alternating scanning electron microscopy imaging and focused ion beam milling has also been used. Unfortunately, these techniques are time- and labor-intensive, with significant sample preparation required and lengthy analysis times. Further, the resulting 3D images are qualitative, require manual identification, and do not capture statistically-representative populations. High energy X-ray 3D imaging using a direct-beam or diffracted-beam (High-Energy Diffraction Microscopy) have been developed at the Advanced Photon Source and can produce quantitative information on grains (phase, location, etc.) and pores (size distribution, sphericity) in a material. These techniques require only minutes to characterize a sample volume and are non-destructive, thus suitable for a wide range of existing samples and for confirmatory analyses to be carried out using conventional microscopy techniques. In this first year of the project, all uranium oxide samples were synthesized and characterized using conventional analyses by the analytical chemistry laboratory. Conventional analysis methods included powder x-ray diffraction, scanning electron microscopy, impurity analysis via inductively coupled plasma mass spectrometry, and infrared spectroscopy. Impurity analysis shows a drop in boron content from UO 3 to the lowest U 3 O 8 calcination temperature, but otherwise no appreciable difference in any sample. Analysis of diffraction data shows a flip of peaks from UO 3 dominated for the 600 °C calcined sample to U 3 O 8 dominated at 700 °C and 800 °C. Analysis of scanning electron microscopy images shows that with increased calcination temperature the size distribution of particles seems to increase and broaden. Both of these last findings are in line with previously published data, though this work used significantly fewer particles to simply show similar trends instead of getting truly quantitative particle analysis. Infrared analysis similarly shows ingrowth of U 3 O 8 as calcination temperature is increased, along with depression of peaks associated with UO 3 and water. Samples were prepared for analysis at the Advanced Photon Source at beamline 1-ID. It is anticipated that analysis will occur in November of 2022. AI/ML techniques to de-noise data coming out of 1-ID during the analyses was also developed during this time using previously gathered data. Preliminary results using a self-supervision technique called Noise2Selfshow good de-noising of data. Once the uranium oxide samples are analyzed, real data will be used to test the de-noising and other AI/ML techniques that may be developed in the second year of the project.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Spectroscopic analysis of Pu-bearing compounds in double-walled cells

Spectroscopic analysis of radiological materials has been historically limited to radiological labs with older or less advanced scientific instrumentation. The development of double-walled cells (DWCs) at the Savannah River National Laboratory (SRNL) has enabled Pu-bearing compounds to be removed from radiological laboratories and studied in our radiologically clean spectroscopy laboratory with state-of-the-art instrumentation. In this manuscript, we discuss the contributions of DWCs that have allowed the application of Raman spectroscopy, diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS), diffuse reflectance spectroscopy (DRS) in the shortwave infrared, and gamma spectroscopy at SRNL. Significant advances have been made in the understanding of the thermal decomposition of Pu(III) and Pu(IV) oxalates, alpha-induced damage to the PuO 2 crystal lattice, and the effect of calcination temperatures on the quality of PuO 2 . These techniques have enabled methods to conduct PuO 2 age dating since last calcination and estimate the calcination temperature with Raman spectroscopy and DRS. Additional spectroscopic information measured with DRIFTS has enabled the observation of the evolution of carbon species with calcination temperature, while gamma spectroscopy provides information on age dating since last purification.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗