Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “bulk modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

First principle calculations of structural phase transition and electronic properties in AmTe

The tight-binding linear muffin-tin orbital (TB-LMTO) with in the local density approximation is used to calculate total energy, lattice parameters, bulk modulus, density of states and energy band structure of americium telluride at ambient as well as at high pressure. It is found that AmTe is stable in NaCl – type structure under ambient pressure. The phase transition pressure was found to be 15.0 GPa from NaCl-type (B{sub 1}-phase) structure to CsCl-type (B{sub 2}-phase) structure for this compound. From energy band diagram it is observed that AmTe exhibit metallic behaviour. The calculated ground state properties such as lattice parameters and bulk modulus are in general good agreement with the available results.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Anorthite: Thermal equation of state to high pressures

The shock wave (Hugoniot) data on single crystal and porous anorthite (CaAl2Si208) to pressures of 120 GPa are presented. These data are inverted to yield high pressure values of the Grueneisen parameter, adiabatic bulk modulus, and coefficient of thermal expansion over a broad range of pressures and temperatures which in turn are used to reduce the raw Hugoniot data and construct an experimentally based, high pressure thermal equation of state for anorthite. The hypothesis that higher order anharmonic contributions to the thermal properties decrease more rapidly upon compression than the lowest order anharmonicities is supported. The properties of anorthite corrected to lower mantle conditions show that although the density of anorthite is comparable to that of the lower most mantle, its bulk modulus is considerably less, hence making enrichment in the mantle implausible except perhaps near its base.

Jeanloz, R.↗

Effect of Phase Transitions on Compressional-Wave Velocites in the Earth Mantle

The velocities of seismic waves in the Earth are governed by the response of the constituent mineral assemblage to perturbations in pressure and stress. The effective bulk modulus is significantly lowered if the pressure of the seismic wave drives a volume-reducing phase transformation. A comparison between the amount of time required by phase transitions to reach equilibrium and the sampling period thus becomes crucial in defining the softening and attenuation of compressional waves within such a two-phase zone3. These phenomena are difficult to assess experimentally, however, because data at conditions appropriate to the Earth's deep interior are required. Here we present synchrotron-based experimental data that demonstrate softening of the bulk modulus within the two-phase loop of olivine-ringwoodite on a timescale of 100 s. If the amplitude of the pressure perturbation and the grain size are scaled to those expected in the Earth, the compressional-wave velocities within the discontinuities at 410, 520 and, possibly, 660 km are likely to be significantly lower than otherwise expected. The generalization of these observations to aluminium-controlled phase transitions raises the possibility of large velocity perturbations throughout the upper 1,000 km of the mantle.

58 GEOSCIENCES↗

Effects of Porosity and Pore Microstructure on the Elastic Properties of Unpoled PZT 95/5-2Nb

Effects of porosity level and pore morphology on the isotropic elastic responses of unpoled porous PZT 95/5-2Nb ferroelectric ceramic are characterized using a simple isotropic elastic response model giving relations between the average stresses and strains of the porous ceramic and the solid matrix surrounding the pores. The model parameters depend on the elastic properties of the solid ceramic material, volume fraction of pores, and two additional material properties that reflect the composition and microstructure of the composite material. Measurements of the effective bulk modulus and shear modulus of the porous ceramic, with corresponding expressions for these quantities from the response model, allow characterization of the additional material properties. It is found that the two material properties reflecting the effect of pore morphology and grain size on the elastic response of unpoled porous PZT 95/5-2Nb ferroelectric ceramics can be expressed in a form that depends explicitly on the porosity level and two parameters dependent solely on the pore morphology and ceramic grain size. Two applications of the model are presented: a simple prediction of the effective bulk modulus and shear modulus for the porous ceramic as a function of porosity for the pore morphologies and grain sizes examined, and a prediction of the effective volume strains, including effects due to the ferroelectric to antiferroelectric phase transformation, for the various ceramics during hydrostatic pressurization.

36 MATERIALS SCIENCE↗

Equation of State and High Pressure Irreversible Amorphization in Y[subscript 3] Fe[subscript 5]O[subscript 12]

The change of crystal structure in yttrium iron garnet Y{sub 3}Fe{sub 5}O{sub 12} was studied at room temperature at high pressures up to {approx}55 GPa by the x-ray diffraction technique in diamond anvil cells. At a pressure of about {approx}50 GPa, a drastic change in the x-ray diffraction pattern was observed indicating the transition into an amorphouslike state. When the pressure was increased, the bulk modulus of YIG was found to be 193 {+-} 4 GPa. It was also found that the amorphous state was retained after decompression down to ambient pressure. From the shape of x-ray patterns in the 'amorphous' phase, it was concluded that the local atomic structure consists of iron-oxygen FeO{sub 6} octahedral complexes with disordered orientations of local axis and of randomly arranged others ion fragments with the overall Y{sub 3}Fe{sub 5}O{sub 12} composition. For the amorphous phase, it was evaluated that the bulk modulus of FeO{sub 6} octahedral complexes is about 260 GPa.

36 MATERIALS SCIENCE↗

Structural response in FeCl2 (iron chloride) to pressure-induced electro-magnetic transitions

High pressure (HP) synchrotron x-ray diffraction studies were carried out in FeCl{sub 2} together with resistivity (R) studies, at various temperatures and pressures to 65 GPa using diamond anvil cells. This work follows a previous HP {sup 57}Fe Mossbauer study in which two pressure-induced (PI) electronic transitions were found interpreted as: (i) quenching of the orbital-term contribution to the hyperfine field concurring with a tilting of the magnetic moment by 55 degrees and (ii) collapse of the magnetism concurring with a sharp decrease of the isomer shift (IS). The R(P,T) studies affirm that the cause the collapse of the magnetism is a PI p-d correlation breakdown, leading to an insulator-metal transition at {approx}45 GPa and is not due to a spi-Ir,crossover (S=2 {yields} S=0). The structure response to the pressure evolution of the two electronic phase transitions starting at low pressures (LP), through an intermediate phase (IP) 30-57 GPa, and culminating in a high-pressure phase (HP), P >32 GPa, can clearly be quantified. The IP-HP phases coexist through the 32-57 GPa range in which the HP abundance increases monotonically at the expense of the IP phase. At the LP-IP interface no volume change is detected, yet the c-axis increases and the a-axis shrinks by 0.21 Angstroms and 0.13 Angstroms, respectively. The fit of the equation of state of the combined LP-IP phases yields a bulk modulus K{sub 0} = 35.3(1.8) GPa. The intralayer CI-CI distances increases, but no change is observed in Fe-CI bond-length nor are there substantial changes in the interlayer spacing. The pressure-induced electronic IP-HP transition leads to a first-order structural phase transition characterized by a decrease in Fe-CI bond length and an abrupt drop in V(P) by {approx}3.5% accompanying the correlation breakdown. In this transition no symmetry change is detected,and the XRD data could be satisfactorily fitted with the CdI{sub 2} structure. The bulk modulus of the HP phase is practically the same as that of the LP-IP phases suggesting negligible changes in the phonon density of state.

36 MATERIALS SCIENCE↗

Synthesis and Structural Stability of Ti2GeC

Mn+1AXn compounds have gathered huge momentum because of its exciting properties. In this paper we report the synthesis of ternary layered ceramic Cr2GeC, a 211 Mn+1AXn compound by hot-pressing. Scanning electron microscopy and X-ray diffraction have been employed to characterize the new synthesized phase. High-pressure compressibility of Cr2GeC were measured using diamond anvil cell and synchrotron radiation at room temperature up to 48 GPa. No phase transformation was observed in the experimental pressure range. The bulk modulus of Cr2GeC calculated using the Birch-Murnaghan equation of state is 169 {+-} 3 GPa, with K? = 3.05 {+-} 0.15.

43 PARTICLE ACCELERATORS↗

Hardness, elastic, and electronic properties of chromium monoboride

Here, we report high-pressure synthesis of chromium monoboride (CrB) at 6 GPa and 1400 K. The elastic and plastic behaviors have been investigated by hydrostatic compression experiment and micro-indentation measurement. CrB is elastically incompressible with a high bulk modulus of 269.0 (5.9) GPa and exhibits a high Vickers hardness of 19.6 (0.7) GPa under the load of 1 kg force. Based on first principles calculations, the observed mechanical properties are attributed to the polar covalent Cr-B bonds interconnected with strong zigzag B-B covalent bonding network. The presence of metallic Cr bilayers is presumably responsible for the weakest paths in shear deformation.

36 MATERIALS SCIENCE↗

Pressure-Induced Invar Behavior in Pd[subscript 3]Fe

Synchrotron x-ray diffraction (XRD) measurements, nuclear forward scattering (NFS) measurements, and density functional theory (DFT) calculations were performed on L1{sub 2}-ordered Pd{sub 3}Fe. Measurements were performed at 300 K at pressures up to 33 GPa, and at 7 GPa at temperatures up to 650 K. The NFS revealed a collapse of the Fe57 magnetic moment between 8.9 and 12.3 GPa at 300 K, coinciding with a transition in bulk modulus found by XRD. Heating the sample under a pressure of 7 GPa showed negligible thermal expansion from 300 to 523 K, demonstrating Invar behavior. Zero-temperature DFT calculations identified a ferromagnetic ground state and showed several antiferromagnetic states had comparable energies at pressures above 20 GPa.

36 MATERIALS SCIENCE↗

Structural studies on Na[subscript 0.75]CoO[subscript 2] thermoelectric material at high pressures

The crystal structure of Na{sub 0.75}CoO{sub 2} was studied at ambient and low temperatures down to 10 K at pressures up to 40 GPa using synchrotron x-rays and a diamond cell in angle dispersion geometry. A reduction in the c/a ratio was observed at both conditions with the application of pressure. An increase in Co-O bond lengths and a decrease in Na-O bond lengths were observed above 10 GPa. The results of the density functional calculations performed agree well with the pressure induced bond length changes. The anomalous change in the c/a ratio and bond lengths indicate a pressure induced isostructural phase transition above 10 GPa. Bulk modulus calculations show this compound is less compressible than its hydrated analogues.

36 MATERIALS SCIENCE↗

Thermodynamic properties of La{sub 1−x}A{sub x}CoO₃ (A=K, Cd, Pr and Nd)

We have calculated the thermal and allied properties of La{sub 1–x}A{sub x}CoO₃ (A=K, Cd, Pr, Nd and 0≤x≤1) as a function of temperature 1 K≤T≤300 K for the first time using Modified Rigid Ion Model (MRIM). The calculated bulk modulus, specific heat, thermal expansion and other thermodynamic properties obtained from MRIM have presented proper interpretation of the experimental data, for monovalent (K⁺), divalent (Cd₂⁺) and trivalent (Pr³⁺ and Nd³⁺) ion-doped LaCoO₃. In addition, the results on the cohesive energy (Φ), molecular force constant (f), Reststrahlen frequency (υ), Debye temperature (θ}) and Gruneisen parameter (γ) are also discussed. - Graphical abstract: Substitution to trivalent La³⁺ site by K⁺ ions increase the thermal expansion (α) whereas Cd²⁺, Pr³⁺ and Nd³⁺ results in decrease of α in La{sub 1–x}A{sub x}CoO₃₋ (A=K, Cd, Pr, Nd). Highlights: • Probably the first report on the specific heat and thermal expansion in La{sub 1–x}A{sub x}CoO₃. • Thermal properties are computed using the MRIM probably for the first time. • Effect of lattice distortions on bulk modulus and thermal properties is presented. • The negative values of cohesive energy show the stability of these compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Pressure-induced zircon-type to scheelite-type phase transitions in YbPO{sub 4} and LuPO{sub 4}

The tetragonal orthophosphates, YbPO{sub 4} and LuPO{sub 4}, were studied by in situ X-ray diffraction (XRD) at pressures up to 52 and 43 GPa, respectively. A reversible phase transition from the zircon structure-type to the scheelite structure-type was found at {approx}22 GPa for YbPO{sub 4} and 19 GPa for LuPO{sub 4}. Coinciding with the transition from the zircon structure-type to the scheelite structure-type, there is a {approx}10% reduction in volume and a significant increase in the bulk modulus for both compounds. - Graphical abstract: The tetragonal orthophosphates, YbPO{sub 4} and LuPO{sub 4}, show reversible phase transitions from the zircon structure-type to the scheelite structure-type at {approx}22 and 19 Gpa, respectively. Coinciding with the phase transition, there is a {approx}10% reduction in unit cell volume.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High-pressure phase transitions of ScPO[subscript 4] and YPO[subscript 4]

ScPO{sub 4} and YPO{sub 4} with the tetragonal zircon-structure were studied at room temperature and pressures up to -50 GPa. Pressure-induced phase transitions to the sheelite structure occur at 30 GPa for ScPO{sub 4} and 16.3 GPa for YPO{sub 4}, respectively. In addition to the scheelite-type high-pressure phase, an intermediate phase with the monoclinic monazite-type structure formed during the phase transition process of YPO{sub 4}. The high-pressure phases of ScPO{sub 4} and YPO{sub 4} are not quenchable on pressure release. The pressure dependence of the total energy of the different phases was calculated using density-functional method, and the results confirm the experimentally observed phase relations under pressure. Structural parameters and compressibility of each phase were determined by refinement of the x-ray diffraction patterns. The high-pressure phase of ScPO{sub 4} has a very large bulk modulus [376(8) GPa].

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ab initio investigation of Ti{sub 2}Al(C,N) solid solutions

M{sub n+1}AX{sub n} phases (M: early transition metal, A: IIIA- or IVA-group element, X: carbon or nitrogen) are layered ternary compounds that possess both metal- and ceramic-like properties with numerous potential applications in bulk and thin film forms, particularly under high-temperature conditions. In this work, we use the cluster expansion formalism to investigate the energetics of C-N interactions across the entire Ti{sub 2}AlC-Ti{sub 2}AlN composition range. It is shown that there is a definite tendency for ordering in the C,N sublattice. However, the molar volume and bulk modulus of the ordered structures found along the Ti{sub 2}AlC-Ti{sub 2}AlN composition range show small deviations from the (linear) rule of mixing, indicating that despite the ordering tendencies, the C-N interactions are not strong and the solution becomes disordered at relatively low temperatures. Random solid solutions of Ti{sub 2}AlC{sub 1-x}N{sub x} are simulated using special quasirandom structures (SQS) with x=0.25, 0.50, and 0.75. The thermodynamic properties of these structures are compared to those of the structures found to belong to the ground state through the cluster expansion approach. It is found that the structural properties of these approximations to random alloys do not deviate significantly from Vegard's law. The trend in the structural parameters of these SQS are found to agree well with available experimental data and the predictions of the bulk modulus suggest a very weak alloying effect--with respect to Vegard's law--on the elastic properties of Ti{sub 2}AlC{sub 1-x}N{sub x}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

High-Pressure Study of Perovskites and Postperovskites in the (Mg,Fe)GeO 3 System

The effect of incorporation of Fe 2+ on the perovskite ( Pbnm ) and postperovskite ( Cmcm ) structures was investigated in the (Mg,Fe)GeO 3 system at high pressures and temperatures using laser-heated diamond anvil cell and synchrotron X-ray diffraction. Samples with compositions of Mg# ≥ 48 were shown to transform to the perovskite (~30 GPa and ~1500 K) and postperovskite (>55 GPa, ~1600-1800 K) structures. Compositions with Mg# ≥ 78 formed single-phase perovskite and postperovskite, whereas those with Mg# < 78 showed evidence for partial decomposition. The incorporation of Fe into the perovskite structure causes a decrease in octahedral distortion as well as a modest decrease in bulk modulus (K 0 ) and a modest increase in zero-pressure volume (V 0 ). It also leads to a decrease in the perovskite-to-postperovskite phase transition pressure by ~9.5 GPa over compositions from Mg#78 to Mg#100.

36 MATERIALS SCIENCE↗

Many-body ab initio diffusion quantum Monte Carlo applied to the strongly correlated oxide NiO

We present a many-body diffusion quantum Monte Carlo (DMC) study of the bulk and defect properties of NiO. We find excellent agreement with experimental values, within 0.3%, 0.6%, and 3.5% for the lattice constant, cohesive energy, and bulk modulus, respectively. The quasiparticle bandgap was also computed, and the DMC result of 4.72 (0.17) eV compares well with the experimental value of 4.3 eV. Furthermore, DMC calculations of excited states at the L, Z, and the gamma point of the Brillouin zone reveal a flat upper valence band for NiO, in good agreement with Angle Resolved Photoemission Spectroscopy results. To study defect properties, we evaluated the formation energies of the neutral and charged vacancies of oxygen and nickel in NiO. A formation energy of 7.2 (0.15) eV was found for the oxygen vacancy under oxygen rich conditions. For the Ni vacancy, we obtained a formation energy of 3.2 (0.15) eV under Ni rich conditions. These results confirm that NiO occurs as a p-type material with the dominant intrinsic vacancy defect being Ni vacancy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Pressure induced silver ion displacement in La{sub 3}Ag{sub 0.82}SnS{sub 7}

Highlights: Black-Right-Pointing-Pointer The silver ion shifts with increasing pressure in the direction of the central-point of sulphur trigonal antiprism. Black-Right-Pointing-Pointer Coordination number changes from CN = 3 to CN = 6 at {approx}3 GPa. Black-Right-Pointing-Pointer Zero-pressure bulk modulus is B{sub 0} = 61.74 GPa and the pressure derivative is B{sup Prime }{sub 0}=4.02. Black-Right-Pointing-Pointer No phase transition up to 4.5 GPa was detected. -- Abstract: The compounds with the general formula Ln{sub 3}MTX{sub 7} (space group P6{sub 3}) (Ln - rare-earth element, M - monovalent element (Cu, Ag), T - Si, Ge, Sn and X - S, Se) are interesting owing to the possible application in the field of ionic conductivity. In the crystal structure the face-sharing [Ag(S){sub 6}] triangular antiprisms form the channels where the Ag{sup +} ion can migrate along the crystallographic c axis. High-pressure X-ray diffraction shows that Ag{sup +} ion moves towards the central-point of [Ag(S){sub 6}] when pressure is risen. As a consequence, the coordination number of Ag{sup +} changes from CN = 3 to CN = 6 at {approx}3 GPa. The La{sub 3}Ag{sub 0.82}SnS{sub 7} has stiff structure; zero-pressure bulk modulus is B{sub 0} = 61.74 GPa and the pressure derivative is B{sup Prime }{sub 0}=4.02.

36 MATERIALS SCIENCE↗