SEARCH · Engineering Papers

Results for “bit error”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

All sources NASA NTRS DOE OSTI

NASA NTRS2000

45 Km Horizontal Path Optical Link Experiment

Mountain-top to mountain-top optical link experiments have been initiated at JPL, in order to perform a systems level evaluation of optical communications. Progress made so far is reported. ne NASA, JPL developed optical communications demonstrator (OCD) is used to transmit a laser signal from Strawberry Peak (SP), located in the San Bernadino mountains of California. This laser beam is received by a 0.6 m aperture telescope at JPL's Table Mountain Facility (TMF), located in Wrightwood, California. The optical link is bi-directional with the TMF telescope transmitting a continuous 4-wave (cw) 780 run beacon and the OCD sending back a 840 nm, 100 - 500 Mbps pseudo noise (PN) modulated, laser beam. The optical link path is at an average altitude of 2 km above sea level, covers a range of 46.8 km and provides an atmospheric channel equivalent to approx. 4 air masses. Average received power measured at either end fall well within the uncertainties predicted by link analysis. The reduction in normalized intensity variance (sigma(sup 2, sub I)) for the 4-beam beacon, compared to each individual beam, at SP, was from approx. 0.68 to 0.22. With some allowance for intra-beam mis-alignment, this is consistent with incoherent averaging. The sigma(sup2, sub I) measured at TMF approx. 0.43 +/- 0.22 exceeded the expected aperture averaged value of less than 0.1, probably because of beam wander. The focused spot sizes of approx. 162 +/- 6 microns at the TMF Coude and approx. 64 +/- 3 microns on the OCD compare to the predicted size range of 52 - 172 microns and 57 - 93 microns, respectively. This is consistent with 4 - 5 arcsec of atmospheric "seeing". The preliminary evaluation of OCD's fine tracking indicates that the uncompensated tracking error is approx. 3.3 micro rad compared to approx. 1.7 micro rad observed in the laboratory. Fine tracking performance was intermittent, primarily due to beacon fades on the OCD tracking sensor. The best bit error rates observed while tracking worked were 1E-5 to 1E-6.

Biswas, A.↗

NASA NTRS2009

Ultra High Power and Efficiency Space Traveling-Wave Tube Amplifier Power Combiner with Reduced Size and Mass for NASA Missions

In the 2008 International Microwave Symposium (IMS) Digest version of our paper, recent advances in high power and efficiency space traveling-wave tube amplifiers (TWTAs) for NASA s space-to-Earth communications are presented. The RF power and efficiency of a new K-Band amplifier are 40 W and 50 percent and that of a new Ka-Band amplifier are 200 W and 60 percent. An important figure-of-merit, which is defined as the ratio of the RF power output to the mass (W/kg) of a TWT, has improved by a factor of ten over the previous generation Ka-Band devices. In this extended paper, a high power, high efficiency Ka-band combiner for multiple TWTs, based on a novel hybrid magic-T waveguide circuit design, is presented. The measured combiner efficiency is as high as 90 percent. In addition, at the design frequency of 32.05 GHz, error-free uncoded BPSK/QPSK data transmission at 8 megabits per second (Mbps), which is typical for deep space communications is demonstrated. Furthermore, QPSK data transmission at 622 Mbps is demonstrated with a low bit error rate of 2.4x10(exp -8), which exceeds the deep space state-of-the-art data rate transmission capability by more than two orders of magnitude. A potential application of the TWT combiner is in deep space communication systems for planetary exploration requiring transmitter power on the order of a kilowatt or higher.

Simons, Rainee N.↗

NASA NTRS1997

Error Control Coding Techniques for Space and Satellite Communications

Bootstrap Hybrid Decoding (BHD) (Jelinek and Cocke, 1971) is a coding/decoding scheme that adds extra redundancy to a set of convolutionally encoded codewords and uses this redundancy to provide reliability information to a sequential decoder. Theoretical results indicate that bit error probability performance (BER) of BHD is close to that of Turbo-codes, without some of their drawbacks. In this report we study the use of the Multiple Stack Algorithm (MSA) (Chevillat and Costello, Jr., 1977) as the underlying sequential decoding algorithm in BHD, which makes possible an iterative version of BHD.

Costello, Daniel J., Jr.↗

NASA NTRS1981

Simulation and studies of spaceborne synthetic aperture radar image quality with reduced bit rate

A computer simulation program that is used to study the effects of digitization in spaceborne synthetic aperture radar systems is described. An analytical study of the distortion noise introduced by the digitization process at various gain settings, sampling rates and bit error rates is presented and the results agree well with those obtained from the simulation program. The simulation program is also used to study the spatial frequency response of hard-limiting (quantizing to 1-bit) synthetic aperture radar systems. The implications of these results on synthetic aperture radar system design are discussed.

Li, F.↗

NASA NTRS1985

Further Results on Rate 1/N Convolutional Code Constructions with Minimum Required SNR Criterion

New good (K, 1/N) convolutional codes for 8 or = to K or = to 13 and 2 or = to N or = to 8 were found and tabulated which require minimum signal-to-noise ratio (SNR) for given desired bit error rates (BER) with Viterbi decoding. The transfer function bound was used for the BER evaluations. These low-rate codes are expected to have a number of applications, especially for systems having large bandwidth-bit time products such as deep space and spread spectrum communication systems.

Lee, P. J.↗

NASA NTRS1985

Further results on rate 1/N convolutional code constructions with minimum required SNR criterion

Lee, P. J.↗

NASA NTRS2000

Error Control Coding Techniques for Space and Satellite Communications

This paper presents a concatenated turbo coding system in which a Reed-Solomom outer code is concatenated with a binary turbo inner code. In the proposed system, the outer code decoder and the inner turbo code decoder interact to achieve both good bit error and frame error performances. The outer code decoder helps the inner turbo code decoder to terminate its decoding iteration while the inner turbo code decoder provides soft-output information to the outer code decoder to carry out a reliability-based soft-decision decoding. In the case that the outer code decoding fails, the outer code decoder instructs the inner code decoder to continue its decoding iterations until the outer code decoding is successful or a preset maximum number of decoding iterations is reached. This interaction between outer and inner code decoders reduces decoding delay. Also presented in the paper are an effective criterion for stopping the iteration process of the inner code decoder and a new reliability-based decoding algorithm for nonbinary codes.

Lin, Shu↗

NASA NTRS1979

Simulation of cosmic-ray induced soft errors and latchup in integrated-circuit computer memories

Soft errors have been induced in solid-state static RAM's by iron nuclei from the Lawrence Berkeley Laboratory (LBL) Bevalac, in experiments designed to prove the ability of iron-group cosmic rays to generate such errors. Subsequently, various delidded device types were tested in beams of argon and krypton ions from the LBL 88-inch Cyclotron, at energies near 2 MeV/nucleon. The latter tests showed that some devices are essentially immune to bit error while others are quite susceptible. Good agreement was obtained with model predictions in cases where the latter exist. Latchup, whose cause is attributed to individual heavy ions, was also observed in some device types.

Kolasinski, W. A.↗

NASA NTRS1987

Performance analysis of a hybrid ARQ error control scheme for near earth satellite communications

A robust error control coding scheme is presented. The scheme is a cascaded forward error correction (FEC) scheme supported by parity retransmissions for further error correction in the erroneous data words. The error performance and throughput efficiency of the scheme are analyzed. Two specific schemes are proposed for NASA near earth satellite communications. It is shown that both schemes provide high reliability and throughput efficiency even for high channel bit error rates in the range of .002. The schemes are suitable for high data rate file transfer.

Lin, Shu↗

NASA NTRS1977

Analysis of transmission error effects on the transfer of real-time simulation data

An analysis was made to determine the effect of transmission errors on the quality of data transferred from the Terminal Area Air Traffic Model to a remote site. Data formating schemes feasible within the operational constraints of the data link were proposed and their susceptibility to both random bit error and to noise burst were investigated. It was shown that satisfactory reliability is achieved by a scheme formating the simulation output into three data blocks which has the priority data triply redundant in the first block in addition to having a retransmission priority on that first block when it is received in error.

Credeur, L.↗

NASA NTRS2000

T1 VSAT Fade Compensation Statistical Results

New satellite communication systems are steadily seeking to use higher frequency bands to accommodate the requirements for additional capacity. At these higher frequencies, propagation impairments that did not significantly affect the signal at lower frequencies begin to have considerable impact. In Ka-band. the next logical commercial frequency band to be used for satellite communication, attenuation of the signal due to rain is a primary concern. An experimental satellite built by NASA, the Advanced Communication Technology Satellite (ACTS). launched in September 1993, is the first U.S. communication satellite operating in the Ka-band. In addition to higher carrier frequencies, a number of other new technologies, including on-board baseband processing. multiple beam antennas, and rain fade detection and compensation techniques, were designed into the ACTS. Verification experiments have been conducted since the launch to characterize the new technologies. The focus of this paper is to characterize the method used by the ACTS TI Very Small Aperture Terminal (TI VSAT) ground stations in detecting the presence of fade in the communication signal and to adaptively compensate for it by the addition of burst rate reduction and forward error correction. Measured data obtained from the ACTS program was used to validate the compensation technique. A software process was developed and demonstrated to statistically characterize the increased availability achieved by the compensation techniques in terms of the bit error rate time enhancement factor. Several improvements to the ACTS technique are discussed and possible implementations for future Ka band system are offered.

Johnson, Sandra K.↗

NASA NTRS2001

Analysis of Fade Detection and Compensation Experimental Results in a Ka-Band Satellite System

The frequency bands being used for new satellite communication systems are constantly increasing to accommodate the requirements for additional capacity. At these higher frequencies, propagation impairments that did not significantly affect the signal at lower frequencies begin to have considerable impact. In Ka-band, the next logical commercial frequency band to be used for satellite communication, attenuation of the signal due to rain is a primary concern. An experimental satellite built by NASA, the Advanced Communication Technology Satellite (ACTS), launched in September 1993, is the first US communication satellite operating in the Ka-band. In addition to higher carrier frequencies, a number of other new technologies, including onboard baseband processing, multiple beam antennas, and rain fade detection and compensation techniques, were designed into the ACTS. Verification experiments have been conducted since the launch to characterize the new technologies. The focus of this thesis is to describe and validate the method used by the ACTS Very Small Aperture Terminal (VSAT) ground stations in detecting the presence of fade in the communication signal and to adaptively compensate for it by the addition of burst rate reduction and forward error correction. Measured data obtained from the ACTS program is used to validate the compensation technique. In this thesis, models in MATLAB are developed to statistically characterize the increased availability achieved by the compensation techniques in terms of the bit error rate time enhancement factor. Several improvements to the ACTS technique are discussed and possible implementations for future Ka-band systems are also presented.

Johnson, Sandra↗

NASA NTRS2006

Coherent Optical Focal Plane Array Receiver for PPM Signals: Investigation and Applications

The performance of a coherent optical focal plane array receiver for PPM signals under atmospheric turbulence is investigated and applications of this system are addressed. The experimental demonstration of this project has already been explained in previous publications [1]. This article shows a more exhaustive analysis of the expressions needed to obtain the Bit Error Rate (BER) for the real system under study in the laboratory. Selected experimental results of this system are described and compared with theoretical BER expressions, and array combining gains are presented. Receiver sensitivity in terms of photons per bit (PPB) is examined; BER results are shown as a function of signal to noise ratios, (SNR), as well as a function of photons per symbol, and photons per bit.

shot noise limited↗

NASA NTRS1979

Comparison of phase modulation systems

Comparison of the energy to noise ratio necessary to obtain a given modulation bit error probability has indicated that three-phase modulation is about 0.75 db superior to four-phase. It is shown that this apparent superiority results entirely from the greater bandwidth required by the three-phase system for the same bit transmission rate. Two further comparison criteria are proposed, which are based on the cut-off rate R sub 0 of the discrete channel created by the modulation system. For the criterion which constrains both the bandwidth and transmitted power, it is shown that four-phase modulation is always superior to three-phase modulation. The conclusion is that three-phase modulation offers no practical advantage over four-phase modulation.

Massey, J. L.↗

NASA NTRS1980

The performance of suppressed carrier receivers in a pulsed RFI environment

This paper investigates the tracking performance of a Costas loop in the presence of single and multiple in-band pulsed RFI signals and receiver additive noise. It is shown that the loop's tracking performance is very sensitive to the pulse durations of the RFI signals, as well as their repetition rates and peak powers relative to those of the desired signal. The presence of in-band RFI can affect the loop's tracking performance in basically three ways. 1) The loop tracks the composite phase of the RFI instead of the phase of the desired signal when the effective RFI power is greater than that of the signal. 2) When the effective RFI power is not sufficiently large to capture the loop, there still will exist static phase error biases which cause the loop to lock at a phase between that of the desired signal and the composite RFI. 3) There is an increase in the rms phase jitter over the nominal design. These latter two effects degrade the bit error probability performance of the receiver. More significantly, if the nominal loop bandwidth is not designed properly to account for the increase in jitter phenomenon, frequency cycle slipping may result.

Simon, M. K.↗

NASA NTRS1974

Shuttle bit rate synchronizer

A shuttle bit rate synchronizer brassboard unit was designed, fabricated, and tested, which meets or exceeds the contractual specifications. The bit rate synchronizer operates at signal-to-noise ratios (in a bit rate bandwidth) down to -5 dB while exhibiting less than 0.6 dB bit error rate degradation. The mean acquisition time was measured to be less than 2 seconds. The synchronizer is designed around a digital data transition tracking loop whose phase and data detectors are integrate-and-dump filters matched to the Manchester encoded bits specified. It meets the reliability (no adjustments or tweaking) and versatility (multiple bit rates) of the shuttle S-band communication system through an implementation which is all digital after the initial stage of analog AGC and A/D conversion.

Huey, D. C.↗

NASA NTRS1990

Modelling and computationally efficient time domain linear equalisation of nonlinear bandlimited QPSK satellite channels

The problem of modeling and equalization of a nonlinear satellite channel is considered. The channel is assumed to be bandlimited and exhibits both amplitude and phase nonlinearities. In traditional models, computations are usually performed in the frequency domain and solutions are based on complex numerical techniques. A discrete time model is used to represent the satellite link with both uplink and downlink white Gaussian noise. Under conditions of practical interest, a simple and computationally efficient time-domain design technique for the minimum mean square error linear equalizer is presented. The efficiency of this technique is enhanced by the use of a fast and simple iterative algorithm for the computation of the autocorrelation coefficients of the output of the nonlinear channel. Numerical results on the evaluations of bit error probability and other relevant parameters needed in the design and analysis of a nonlinear bandlimited QPSK system demonstrate the simplicity and computational efficiency of the proposed approach.

Konstantinides, K.↗

NASA NTRS1995

Error control techniques for satellite and space communications

This report focuses on the results obtained during the PI's recent sabbatical leave at the Swiss Federal Institute of Technology (ETH) in Zurich, Switzerland, from January 1, 1995 through June 30, 1995. Two projects investigated various properties of TURBO codes, a new form of concatenated coding that achieves near channel capacity performance at moderate bit error rates. The performance of TURBO codes is explained in terms of the code's distance spectrum. These results explain both the near capacity performance of the TURBO codes and the observed 'error floor' for moderate and high signal-to-noise ratios (SNR's). A semester project, entitled 'The Realization of the Turbo-Coding System,' involved a thorough simulation study of the performance of TURBO codes and verified the results claimed by previous authors. A copy of the final report for this project is included as Appendix A. A diploma project, entitled 'On the Free Distance of Turbo Codes and Related Product Codes,' includes an analysis of TURBO codes and an explanation for their remarkable performance. A copy of the final report for this project is included as Appendix B.

Costello, Daniel J., Jr.↗