Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “annular”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Duration test of an annular colloid thruster.

An annular colloid thruster was continuously operated for 1023 hours. Performance was stable with no sparking and negligible drain currents observed. An average thrust of 25.1 micropounds and an average specific impulse of 1160 seconds were obtained at an accelerating voltage of 15 k he thruster exhaust beam was continuously neutralized using electrons and electrostatic vectoring was demonstrated periodically. The only clear trend with time was an increase in specific impulse during the last third of the test period. From these results the thruster lifetime was estimated to be over an order of magnitude greater than the test duration.

Perel, J.↗
NASA NTRS1973

Control of exit velocity profile of an asymmetric annular diffuser using wall suction

An asymmetric annular diffuser equipped with wall bleed (suction) capability was tested for controllability of exit velocity profile. The diffuser area ratio was 3.2, and the length to inlet height ratio was 1.6. Results show that the diffuser radial exit velocity profile could be controlled from a hub peaked to a tip peaked form by selective use of bleed on the outer wall or on both diffuser walls. Based on these results, application of the diffuser bleed technique to gas turbine combustors may be possible. Diffuser bleed could be used to tailor the airflow distribution for optimizing combustor performance at a variety of operating conditions.

Juhasz, A. J.↗
NASA NTRS1973

Comparison of combustion characteristics of ASTM A-1, propane, and natural-gas fuels in an annular turbojet combustor

The performance of an annular turbojet combustor using natural-gas fuel is compared with that obtained using ASTM A-1 and propane fuels. Propane gas was used to simulate operation with vaporized kerosene fuels. The results obtained at severe operating conditions and altitude relight conditions show that natural gas is inferior to both ASTM A-1 and propane fuels. Combustion efficiencies were significantly lower and combustor pressures for relight were higher with natural-gas fuel than with the other fuels. The inferior performance of natural gas is shown to be caused by the chemical stability of the methane molecule.

Wear, J. D.↗
NASA NTRS1973

Effect of fuel zoning and fuel nozzle design on pollution emissions at ground idle conditions for a double-annular ram-induction combustor

An exhaust emission survey was conducted on a double-annular ram induction combustor at simulated ground idle conditions. The combustor was designed for a large augmented turbofan engine capable of sustained flight speeds up to Mach 3.0. The emission levels of total hydrocarbon (THC), carbon monoxide, carbon dioxide, and nitric oxide were measured. The effects of fuel zoning, fuel nozzle design, and operating conditions (inlet temperature and reference Mach number) on the level of these emissions were determined. At an overall combustor fuel/air ratio of 0.007, fuel zoning reduced THC emissions by a factor of 5 to 1. The reduction in THC emissions is attributed to the increase in local fuel/air ratio provided by the fuel zoning. An alternative method of increasing fuel/air ratio would be to operate with larger-than-normal compressor overboard bleed; however, analysis on this method indicated an increase in idle fuel consumption of 20 percent. The use of air-atomizing nozzles reduced the THC emissions by 2 to 1.

Clements, T. R.↗
NASA NTRS1973

Performance gains by using heated natural-gas fuel in an annular turbojet combustor

A full-scale annular turbojet combustor was tested with natural gas fuel heated from ambient temperature to 800 K (980 F). In all tests, heating the fuel improved combustion efficiency. Two sets of gaseous fuel nozzles were tested. Combustion instabilities occurred with one set of nozzles at two conditions: one where the efficiency approached 100 percent with the heated fuel; the other where the efficiency was very poor with the unheated fuel. The second set of nozzles exhibited no combustion instability. Altitude relight tests with the second set showed that relight was improved and was achievable at essentially the same condition as blowout when the fuel temperature was 800 K (980 F).

Marchionna, N. R.↗
NASA NTRS1973

Evaluation of an experimental short-length annular combustor: One-side-entry dilution airflow concept

A test program was conducted to evaluate an experimental short-length annular combustor that uses a one-side-entry dilution airflow concept. The combustor design features scoops on the outer liner for controlling the primary- and secondary-zone airflow distribution. Combustor inlet total pressures were limited to 62 N/sq cm (90 psia) with inlet-air temperatures from 590 K (600 F) to 890 K (1150 F). At a diffuser inlet Mach number of 0.25, the exit temperature pattern factor was 0.44 with an average exit temperature of 1436 K (2124 F) and a total pressure loss of 4.3 percent. At a diffuser inlet Mach number of 0.31, the exit temperature pattern factor was reduced to 0.29 with an average exit temperature of 1450 K (2151 F) and a total pressure loss of 6.1 percent. Nominal combustion efficiencies of 100 percent were obtained with the ASTM A-1 fuel. Exhaust gas emissions, smoke, and altitude relight data are included with exit-temperature profiles and distribution patterns.

Humenik, F. M.↗
NASA NTRS1973

Radiation configuration factors for annular rings and hemispherical sectors.

In the application of Monte Carlo computer techniques to the study of problems in the free molecular flow regime, the analogy between radiation heat transfer with diffuse emissions and the free molecular flow field makes it possible to use the radiation configuration factors as a test on the operation of the Monte Carlo program. A source plane which was an annular ring of arbitrary radius around a sphere with the center of the disk coincident with the center of the sphere was examined. Since various indicators seemed to verify the correct operation of the program, the program was used to calculate the radiation configuration factors. The study adds a new geometry to the general literature on radiation configuration factors.

Ballance, J. O.↗
NASA NTRS1973

A theoretical and experimental study of sound attenuation in an annular duct.

The flow duct used in the experiments for this study was described in an earlier paper by Plumblee and Dean (1972). Angular and radial standing modes were excited in isolation, and the modal attenuation and phase speed were measured in an annular duct with locally reacting liners. Contour maps of constant attenuation and phase speed were computed in the wall impedance plane for no-flow and several flow conditions, and experimental data were compared with some of these calculations. The effect of flow on modal attenuation and phase speed was measured and is theoretically verified. The major result of this study is the verification of theoretical predictions which ultimately can lead to a duct liner design optimization without resort to expensive and lengthy test programs.

Plumblee, H. E.↗
NASA NTRS1974

Performance of an asymmetric short annular diffuser with a nondiverging inner wall using suction

The performance of a short highly asymmetric annular diffuser equipped with wall bleed (suction) capability was evaluated at nominal inlet Mach numbers of 0.188, 0.264, and 0.324 with the inlet pressure and temperature at near ambient values. The diffuser had an area ratio of 2.75 and a length- to inlet-height ratio of 1.6. Results show that the radial profiles of diffuser exit velocity could be controlled from a severely hub peaked to a slightly tip biased form by selective use of bleed. At the same time, other performance parameters were also improved. These results indicate the possible application of the diffuser bleed technique to control flow profiles to gas turbine combustors.

Juhasz, A.↗
NASA NTRS1974

Effect of diffuser bleed on performance of an annular swirl can combustor

A full-scale annular swirl can combustor equipped with diffuser bleed capability was tested at low fuel-air ratio, burning natural gas fuel. Test results show that, by drawing off a small amount of air on the inner or outer diffuser wall, the radial profile of combustor exit temperature could be changed from a strongly tip biased, to a strongly hub biased shape. Furthermore, combustor total pressure loss could be reduced by about one third by using a total bleed rate equal to 6 percent of diffuser inlet flow. At simulated engine idle conditions combustion efficiency was increased from 64 percent to nearly 100 percent by using 3 percent outer wall bleed. Combustor blowout performance was also improved significantly by using this diffuser bleed scheme.

Juhasz, A. J.↗
NASA NTRS1974

An integral equation formulation for predicting radiation patterns of a space shuttle annular slot antenna

An integral equation formulation is applied to predict pitch- and roll-plane radiation patterns of a thin VHF/UHF (very high frequency/ultra high frequency) annular slot communications antenna operating at several locations in the nose region of the space shuttle orbiter. Digital computer programs used to compute radiation patterns are given and the use of the programs is illustrated. Experimental verification of computed patterns is given from measurements made on 1/35-scale models of the orbiter.

Jones, J. E.↗
NASA NTRS1974

Subsonic annular wing theory with application to flow about nacelles

A method has recently been developed for calculating the flow over a subsonic nacelle at zero angle of attack. The method makes use of annular wing theory and boundary-layer theory and has shown good agreement with both experimental data and more complex theoretical solutions. The method permits variation of the mass flow by changing the size of a center body.

Mann, M. J.↗
NASA NTRS1973

Development of an annular arc accelerator shock tube driver

An annular arc accelerator (ANAA) shock tube driver has been developed that deposits the energy of an arc discharge into a flowing gas, which then expands and cools without any delay for the opening of a diaphragm. A simplified one-dimensional flow analysis of the ANAA shock tube has been performed, which indicates that shock velocities greater than 40 km/sec may be obtained using a 300-kJ capacitor bank. The ANAA driver consists of a high-pressure driver, an expansion section, and an electrode section. In operation, the cold gas driver is pressurized until the diaphragm bursts, sending a pressure front down the expansion tube to the arc section. When the accelerated flow arrives at the electrode section, a 100-capacitor, 300-kJ capacitor bank is discharged either by breaking an insulating diaphragm between the electrodes or by the triggering of a series of external switches. Shock velocities of 28 km/sec have been obtained, and modifications are described that are expected to improve performance.

Leibowitz, L. P.↗
NASA NTRS1974

Transmission of sound through annular ducts of varying cross sections and sheared mean flow

An asymptotic solution is presented for the transmission and attenuation of acoustic waves in an annular duct of slowly varying cross section which carries a sheared mean flow. The analysis also takes into account the growth of the boundary layer as well as any slow variations in the acoustic liner properties. The problem is reduced to the solution of a first-order ordinary differential equation for the amplitude. The analysis is used to estimate the effects of the variations of the duct cross section and boundary layer growth on the different acoustic modes.

Nayfeh, A. H.↗
NASA NTRS1973

Generalized radiation impedances and reflection coefficients of circular and annular ducts

Morse's equation for the radiation impedance of a vibrating rigid piston is extended to give the generalized radiation impedances of all modes in circular and annular ducts which have arbitrary wall admittance and which terminate in an infinite baffle. The extended equation is reduced to a single infinite integral which is a function of the mode radiation directivity factors. An infinite matrix equation is derived which relates the generalized mode reflection coefficients to the radiation impedances. Results are presented which show that the duct-wall admittance is a significant parameter in the effect of duct-determination reflections and that mode-coupling reflection effects may be more important than direct-mode reflection effects.

Zorumski, W. E.↗
NASA NTRS1974

Application of an integral equation formulation to the prediction of space shuttle annular slot antenna radiation patterns

Pitch and roll plane radiation patterns computed by use of an integral equation formulation are presented for a space shuttle annular slot communications antenna. The excellent agreement between computed patterns and experimental patterns obtained from 1/35 scale models supports the use of this method as a design tool for similar spacecraft/aircraft antenna applications.

Jones, J. E.↗
NASA NTRS1974

Multiple eigenvalues of sound-absorbing circular and annular ducts

Eigenvalue equations of the form D(lambda) = 0 are studied for acoustic modes in circular and annular ducts without flow. The ducts have locally reacting walls with arbitrary wall admittance. It is shown that circular ducts may have double eigenvalues, or wall admittances where both D(lambda) and D prime (lambda) are zero. These double eigenvalues are formed by the coalescence of the lowest-order eigenfunction with some higher-order eigenfunction. The eigenfunctions, or acoustic modes, associated with the double eigenvalues are found to be orthogonal to themselves so that the standard expansion formula for the acoustic field, which is obtained from a separation-of-variables analysis, is invalid. An alternate expansion formula for the acoustic field is derived. This alternate formula shows that the coalesced acoustic mode is linearly amplified by the transmission distance and exponentially attenuated at the expected rate. The expansion formula also reveals a new eigenfunction, or acoustic mode, which is exponentially attenuated at the same rate as the coalesced eigenfunction.

Zorumski, W. E.↗
NASA NTRS1974

Analytical and experimental investigation of flow fields of annular jets with and without swirling flow

Analytical and experimental studies were performed to define the flowfield of annular jets, with and, without swirling flow. The analytical model treated configurations with variations of flow angularities, radius ratio, and swirl distributions. Swirl distributions characteristic of stator vanes and rotor blade rows, where the total pressure and swirl distributions are related were incorporated in the mathematical model. The experimental studies included tests of eleven nozzle models, both with and, without swirling exhaust flow. Flowfield surveys were obtained and used for comparison with the analytical model. This comparison of experimental and analytical studies served as the basis for evaluation of several empirical constants as required for application of the analysis to the general flow configuration. The analytical model developed during these studies is applicable to the evaluation of the flowfield and overall performance of the exhaust of statorless lift fan systems that contain various levels of exhaust swirl.

Simonson, M. R.↗