Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “aerodynamic modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

High Efficiency 2-Bladed Utility Wind Turbine Enhanced by CoFlow Jet Active Flow Control

The aerodynamic performance and power output of a high efficiency Co-Flow Jet (CFJ) 2-bladed Wind Turbine is studied in this paper. CFJ is a Zero-Net-Mass-Flux (ZNMF) active flow control method that dramatically increases airfoil lift coefficient and suppresses flow separation at a low energy expenditure. The 3D Reynolds Averaged Navier-Stokes (RANS) equations with one-equation Spalart-Allmaras (SA) turbulence model are solved to simulate the 3D flows of the wind turbines. The CFJ-Wind Turbine in this paper is modified from the NREL 3-bladed 3.4 MW reference wind turbine with the same RPM, blade length, distribution of chord, twist, and bending. The CFJ 2-bladed wind turbine utilizes the CFJ-NACA 64 series airfoils at most of the blade span from 31.88\% to the tip. The CFJ injection and suction slots are implemented along the full blade span to enhance the effectiveness and power output. The study shows that the 2-bladed CFJ turbine significantly increases power output compared with the 3-bladed baseline turbine at all wind speeds by 15.8\% at the wind speed of 9.8 m/s and by 25.9\% at 4 m/s respectively. The efficiency enhancement is substantially more at the low wind speed than at high wind speed. This would be very beneficial to increase the annual power output or capacity factor as wind turbines work at the speeds lower than the rated speed for most of the time. The results show that the flow field around the blade surface presents a significant enhanced suction peak near the blade leading edge, which results in a very high tangential force and thus increased wind turbine net power coefficient. Consistent with the previous study for the small NREL Phase VI research wind turbine, this paper demonstrates that CFJ 2-bladed wind turbine is an effective technology to extract more power from the wind at all speeds. This study is just an initial effort to demonstrate the advantage of the CFJ blade with no design optimization. It is believed that there is more potential to further enhance the efficiency improvement.

active flow control↗

Residual stress distribution in an additively manufactured complex structure by neutron diffraction measurement

Residual stress in an aerodynamically shaped Ni-based superalloy airfoil fabricated by laser powder bed fusion was measured by neutron diffraction. The experiment was conducted by considering the complex shape, implementing computer aided experiment planning, and automatic alignment at each rapid measurement. The 3-dimensional (3D) residual stress distribution in the airfoil is presented in this work, which lacks symmetry due to the complex geometry of the airfoil. In conclusion, the results provide theoretical thermal processing models a complete residual stress dataset of simulation validation on 3D shape complex structure.

Residual stress↗

Air Blast Mesh Sensitivity and Pressure Mapping Study

Nose cone structural and aerodynamic characteristics are essential for intelligent design of aircraft, spacecraft, and ballistic systems. Finite element analysis can be used to help understand the structural integrity and flight characteristics of different nose cones. A mesh sensitivity study was undertaken for a particular nose cone geometry that was used in tests at LANL facilities in order to confirm the integrity of the meshed geometry. A simple cone that best matched closed-form theoretical solutions was modeled, and received good correlation to the theory. Complexity was then added back to the nose cone. Parameters applied to the simple cone were then implemented in the nose cone geometry giving assurance of accuracy after the geometry was changed. Nose cone results averaged 6.3% error for radial displacement when compared with the theoretical. Hoop stress averaged 6.0% error and meridional stress averaged 5.7% error at the finest mesh level. Meshes showed signs of convergence when compared to all three theoretical solutions. Finally, pressure time-history data from LANL computational fluid dynamics simulations was applied to the surface of the final nose cone geometry. The pressure data was interpolated from pressure gauge locations onto nearby meshed elements, which allowed for FEA software to run simulations on the cone with the pressure data as a loading condition. The pressure mapping resulted in the ability to understand the nose cone’s rigid body motion that in turn can inform design of future nose cones.

42 ENGINEERING↗

The quest for improved air quality may push China to continue its CO 2 reduction beyond the Paris Commitment

China is challenged with the simultaneous goals of improving air quality and mitigating climate change. The “Beautiful China” strategy, launched by the Chinese government in 2020, requires that all cities in China attain 35 μg/m 3 or below for annual mean concentration of PM 2.5 (particulate matter with aerodynamic diameter less than 2.5 μm) by 2035. Meanwhile, China adopts a portfolio of low-carbon policies to meet its Nationally Determined Contribution (NDC) pledged in the Paris Agreement. Previous studies demonstrated the co-benefits to air pollution reduction from implementing low-carbon energy policies. Pathways for China to achieve dual targets of both air quality and CO 2 mitigation, however, have not been comprehensively explored. Here, we couple an integrated assessment model and an air quality model to evaluate air quality in China through 2035 under the NDC scenario and an alternative scenario (Co-Benefit Energy [CBE]) with enhanced low-carbon policies. Results indicate that some Chinese cities cannot meet the PM 2.5 target under the NDC scenario by 2035, even with the strictest end-of-pipe controls. Achieving the air quality target would require further reduction in emissions of multiple air pollutants by 6 to 32%, driving additional 22% reduction in CO 2 emissions relative to the NDC scenario. Results show that the incremental health benefit from improved air quality of CBE exceeds 8 times the additional costs of CO 2 mitigation, attributed particularly to the cost-effective reduction in household PM 2.5 exposure. The additional low-carbon energy polices required for China’s air quality targets would lay an important foundation for its deep decarbonization aligned with the 2 °C global temperature target.

54 ENVIRONMENTAL SCIENCES↗

Boron coordination change in barium borate melts and glasses and its contribution to configurational heat capacity, entropy, and fragility

High-energy x-ray diffraction from molten and glassy BaB 2 O 4 and BaB 4 O 7 has been performed using aerodynamic levitation and laser heating over a wide range of temperatures. Remarkably, even in the presence of a heavy metal modifier dominating x-ray scattering, it was possible to extract accurate values for the tetrahedral, sp 3 , boron fraction, N 4 , which declines with increasing temperature, using bond valence-based mapping from the measured mean B–O bond lengths while accounting for vibrational thermal expansion. These are used within a boron-coordination-change model to extract enthalpies, ΔH, and entropies, ΔS, of isomerization between sp 2 and sp 3 boron. The results for BaB 4 O 7 , ΔH = 22(3) kJ mol -1 boron, ΔS = 19(2) J mol -1 boron K -1 , agree quantitatively with those found previously for Na 2 B 4 O 7 . Analytical expressions for N 4 (J, T) and associated configurational heat capacity, $C_{P}^{conf}$(J, T), and entropy, S conf (J, T), contributions are extended to cover a wide composition range 0 ≤ J = BaO/B 2 O 3 ≤ 3 using a model for ΔH(J) and ΔS(J) derived empirically for lithium borates. Maxima in the $C_{P}^{conf}$(J, T g ) and fragility index contributions are thereby predicted for J ≲ 1, higher than the maximum observed and predicted in N 4 (J, T g ) at J ≃ 0.6. We discuss the utility of the boron-coordination-change isomerization model in the context of borate liquids containing other modifiers and the prospect of neutron diffraction to aid in empirical determinations of modifier-dependent effects, illustrated by new neutron diffraction data on Ba 11 B 4 O 7 glass, its well-known α-polymorph, and lesser-known δ-phase.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Sensitivity Analysis of Modal Parameters of a Jacket Offshore Wind Turbine to Operational Conditions

Accurate estimation of offshore wind turbine (OWT) modal parameters has a prominent effect on the design loads, lifetime prediction, and dynamic response of the system. Modal parameters can vary during the operation of OWTs. This paper studies the variation and sensitivity analysis of an OWT’s modal parameters with respect to operational and environmental conditions. Three finite element models of a jacket-supported OWT at the Block Island Wind Farm are created within the OpenSees, SAP2000, and OpenFAST platforms and validated using experimental measurements. The OpenFAST model is used to simulate the modal parameters of the turbine under various wind speed, rotor speed, power, yaw angle, mean sea level, blade pitch angle, and soil spring values. The model-predicted modal parameters of the first fore–aft (FA) and side–side (SS) modes are compared to those identified from experimental measurements. Results from the simulations show that the first FA natural frequency and damping ratio mostly depend on the rotor speed and wind speed, respectively, while yaw angle and mean sea level do not have a visible effect. It is observed that there is about 8% stiffening in the first FA frequency and an aerodynamic damping of 7.5% during the operation of the OWT.

17 WIND ENERGY↗

Single-shot picosecond pump coherent Rayleigh scattering thermometry

A single-shot coherent Rayleigh scattering (CRS) technique capable of measurement times less than 10 ns is presented. Here, the use of a mode-locked picosecond pump laser yields repeatable electrostrictive forcing compared to previous CRS experiments using unseeded nanosecond pump pulses, which are beset by shot-to-shot variations. Quantitative measurements are achieved by dispersing the CRS signal onto an EMCCD sensor using a virtually imaged phased array and comparing the experimental spectra to an existing kinetic model with a least-squares fitting routine. Measurements are demonstrated at ambient and low-pressure (2 Torr), low-temperature (100 K) conditions where the CRS measurement is within the collisionless regime. Single-shot statistics indicated precision and accuracy within 4% at ambient conditions and within 8% at low density and temperature conditions. This single-shot CRS technique is a powerful diagnostic tool with potential for multi-parameter measurements in complex flow environments, including high-speed aerodynamic ground test facilities.

Senior, William Charles Bowman [Sandia National La↗

Characterizing the Payback and Profitability for Automated Heavy Duty Vehicle Platooning

Heavy duty vehicle platooning under highway operating conditions has been projected to provide significant fuel economy gains based on aerodynamic drag improvements of the platooning vehicles. Realizing these benefits and the economic viability under real-world operating conditions presents several challenges. The objective of this paper (the third as part of a series) is to analytically quantify the payback and profitability of heavy-duty vehicles platooning across the U.S. Interstate highway system. In this paper, a rigorous assessment of several factors that influence the platooning system payback for an end-user as well as the revenue potential for suppliers who may be utilizing an equipment lease model dependent on end-user savings, is presented. In this assessment key interactions explored include market adoption rates, platooning velocities, platoon-able daily mileage, platooning likelihood, variations in baseline powertrain fuel economy (diesel or electric), price of fuel (diesel or electricity), platooning fuel economy benefits, price of the added technology, and the impact of natural platooning due to traffic interactions. Further, the paper explores the economic impact of higher levels of vehicle automation for the trailing vehicles in the platoon, where extending the driver Hours of Service (HoS) may provide additional financial benefits. While the approach makes use of a limited fidelity vehicle analytical model for longitudinal dynamics and operations economics, the narrative provides application decision personnel with a mechanism and well-defined set of impact factors to consider as part of their architectural selection process.

33 ADVANCED PROPULSION SYSTEMS↗

Internal energy balance and aerodynamic heating predictions for hypersonic turbulent boundary layers

The elemental equation governing heat transfer in aerodynamic flows is the internal energy equation. For a boundary layer flow, a double integration of the Reynolds-averaged form of this equation provides an expression of the wall heat flux in terms of the integrated effects, over the boundary layer, of various physical processes: turbulent dissipation, mean dissipation, turbulent heat flux, etc. Recently available direct numerical simulation data for a Mach 11 cold-wall turbulent boundary layer allows a comparison of the exact contributions of these terms in the energy equation to the wall heat flux with their counterparts modeled in the Reynolds-averaged Navier-Stokes (RANS) framework. Various approximations involved in RANS, both closure models as well as approximations involved in adapting incompressible RANS models to a compressible form, are assessed through examination of the internal energy balance. There are a number of potentially problematic assumptions and terms identified through this analysis. Here, the effect of compressibility corrections of the dilatational dissipation type is explored, as is the role of the modeled turbulent dissipation, in the context of wall heat flux predictions. The results indicate several potential avenues for RANS model improvement for hypersonic cold-wall boundary-layer flows.

42 ENGINEERING↗

Ice nucleation measurements from DRUM impactors during TRACER campaign in the Houston TX region from July to September 2022

During TRACER, three Davis Rotating Uniform size-cut Monitors (DRUM; DRUMAir 4-DRUM) were used to collect aerosols for ice nucleation measurements in the Brooks laboratory at Texas A&M University. The three instruments were located at AMF1 in La Porte, Ancillary site in Guy (ANC), and onboard the Texas A&M Rapid Onsite Atmospheric Measurements Van (ROAM-V). ROAM-V was deployed to capture airmasses behind (maritime) and ahead (continental) of the passage of the sea-breeze front through Houston. On select sampling days, ROAM-V sampled in the morning/mid-day on the coast and then transited to a second inland site for the afternoon/evening. The suite of instruments deployed on ROAM-V included a Condensation Particle Counter (CPC; GRIMM Model 5.403 CPC), Scanning Mobility Particle Sizer (SMPS; TSI 3750 detector, TSI 3082 classifier, TSI 3088 neutralizer, TSI 3081A Differential Mobility Analyzer), Cloud Condensation Nuclei counter (Droplet Measurement Technologies CCN Counter), micro pulse lidar (Droplet Measurement Technologies Micro Pulse LiDAR (miniMPL)), and one of the Davis Rotating Uniform size-cut Monitors (DRUM; DRUMAir 4-DRUM). Before sampling at each location, the latitude and longitude were recorded using the GPS on the phone application “My Altitude”. Each DRUM sampler was operated at a flow rate of 23 LPM. Each DRUM has four stages where the aerodynamic diameter size cuts are as follows: stage 1 larger than 3 μm, stage 2 from 3 to 1.2 μm, stage 3 from 1.2 to 0.34 μm, and stage 4 from 0.34 to 0.15 μm. Pretreated aluminum foil was used as a substrate on all stages. At AMF1 and ANC sites, the DRUMs were operated on the shared aerosol inlet, with generous support of the DOE ARM site staff. These instruments rotated 24 mm per day and only contained aluminum foil substrates. Substrates were changed weekly and transported to Texas A&M for storage in -80C freezer until analysis. The DRUM onboard ROAM-V was operated at a faster rotation rate of 150 mm per day to clearly separate the multiple deployment locations for ROAM-V. For the ROAM-V DRUM, substrates were changed every deployment and transported to Texas A&M for storage in -80C freezer until analysis. At Texas A&M, ice nucleation experiments were conducted to measure the ice nucleation temperature of the ambient aerosol samples collected from the three DRUMs using our previously established procedures (Alsante et al., 2023; Fornea et al., 2009; Matthews et al., 2023). For ice nucleation, only samples collected on stage 3 were analyzed, given that these are the most relevant size (1.2 to 0.34 μm diameter) for potential ice nucleating particles. For the AMF1 and ANC sites, we cut and analyzed 2 mm (2-hour) samples. We analyzed the time periods of the AMF1 site instrument when the ROAM-V was deployed. A 72-hour period from July 11th at 23:49 through July 15th at 1:49 was analyzed from the ANC site instrument. For the ROAM-V instrument, we separated the daily samples by site location. Between 1- and 6-hour independent samples were analyzed at each location. We also cut the ROAM-V samples in half to allow for compositional analysis of the aerosol on the other half of the substrate. All viable samples from the ROAM-V were analyzed. Analysis was done using a custom-built ice nucleation apparatus, recently updated to include an array of 16 individual samples (Matthews et al., 2023). On our experimental setup, we used 100 μL of Ultra-High-Performance Liquid Chromatography (UHPLC) water (Sigma Aldrich, >99.9% purity) to wash off the aerosol from the DRUM substrate. Then, we micropipetted 2 μL droplet samples into each of the 16 wells of the array, using hydrophobically coated microscope slides. Experiments would cycle 28 times from 10 C to -40C over a 20-hour period. During analysis of the TRACER samples, nine experiments were conducted with UHPLC water process blanks that followed an identical preparation procedure. The average freezing temperature and standard deviation for these process blanks is -27.7±2.4 C. This data was collected for ARM Field Campaign AFC07023 and supported by DOE ASR grant DE-SC0021047. For any further questions, please feel free to contact the instrument PI, Sarah D. Brooks, sbrooks@tamu.edu. Alsante, A. N., Thornton, D. C., & Brooks, S. D. (2023). Ice nucleation catalyzed by the photosynthesis enzyme RuBisCO and other abundant biomolecules. Communications Earth & Environment, 4(1), 51. Fornea, A. P., Brooks, S. D., Dooley, J. B., & Saha, A. (2009). Heterogeneous freezing of ice on atmospheric aerosols containing ash, soot, and soil. Journal of Geophysical Research: Atmospheres, 114(D13). DOI:10.1029/2009JD011958 Matthews, B. H., Alsante, A. N., & Brooks, S. D. (2023). Pollen Emissions of Subpollen Particles and Ice Nucleating Particles. ACS Earth and Space Chemistry.

54 ENVIRONMENTAL SCIENCES↗

Direct Observations of Surface Fluxes and Air‐Sea Exchange Coefficients in Low Winds Using a Small Uncrewed Aircraft System

In the marine boundary layer, the exchange of momentum, heat, and moisture occurs between the atmosphere and ocean. Since it is too dangerous for a crewed aircraft to fly close to the ocean surface to directly obtain these measurements, a sUAS (small Uncrewed Aircraft System) is one of the only viable options. On 24 March 2023 a Black Swift Technologies S0 sUAS was deployed from the NOAA P-3 on a calm clear day off the west coast of Florida. For 23 min at the end of the mission, the sUAS flew 8 straight line legs with an average length of 2.15 km, at roughly 10 m above the ocean surface, with wind speeds between 3.0 and 4.5 m s −1 . For the first time over the open ocean using a sUAS, the 4-Hz wind and thermodynamic data was used to calculate surface momentum flux, sensible heat flux, and latent flux using both direct covariance methods and the bulk aerodynamic formulas. Since all the flux quantities can be found using both direct and indirect methods, we are able to calculate the exchange coefficients of momentum flux (C D ), latent heat flux (C E ), and sensible heat flux (C H ) with results that are generally in good agreement with previous studies over the same wind speed range. This study demonstrates the ability of sUAS to measure air-sea interactions. Future intention is to use sUAS to obtain similar measurements in high wind events such as hurricanes which could better help understand hurricane intensification and improve model physics.

Deloach, Christopher J. [Embry-Riddle Aeronautical↗

Experimental and Computational Characterization of a Modified Sioutas Cascade Impactor for Respirable Radioactive Aerosols

Oak Ridge National Laboratory is collecting and characterizing aerosols released when spent nuclear fuel (SNF) rods are fractured in bending. An aerosol collection system was designed and tested to collect respirable sized (<10 μm aerodynamic diameter [AED]) particulates inside a hot cell facility. The setup is a modified version of the commercially available Sioutas cascade impactor, to which additional stages were added to expand the aerosol collection range from 2.5 to ~15 μm AED. To accommodate the additional stages and specific test conditions, the operating flow rate for aerosol collection was reduced, and testing was conducted by using pressure drop measurements, surrogate dust collection, and particle size characterization. The fluid flow distribution within the cascade and its stages was simulated in STAR-CCM+, and the stage-wise pressure drops obtained using the computational fluid dynamics model were then compared to experimental data. Lagrangian particle simulations were also performed, and stage-wise collection statistics were obtained from the simulation for comparison with the experimental data obtained using SNF-surrogate dust particles. The results provide valuable insights into the stage-wise particle collection characteristics of the modified cascade impactor and can also be used to improve the prediction accuracy of the manufacturer-determined analytical correlations.

aerosol modeling↗

Turbulent entrainment in finite-length wind farms

In this article, we present an entrainment-based model for predicting the flow and power output of finite-length wind farms. The model is an extension of the three-layer approach of Luzzatto-Fegiz & Caulfield ( Phys. Rev. Fluids , vol. 3, 2018, 093802) for wind farms of infinite length, and assumes dependence of key flow quantities, such as the wind farm bulk velocity, on the streamwise distance from the farm entrance. To assist our analysis and validate the proposed model, we undertake a series of large-eddy simulations with different turbine spacing arrangements and layouts. Comparisons are also made with the top-down model with entrance effects of Meneveau ( J. Turbul. , vol. 13, 2012, N7) and data from the literature. The finite-length entrainment model is shown to be capable of capturing the power drop between contiguous rows of turbines as well as describing the advection and turbulent transport of kinetic energy in both the entrance and fully developed regions. The fully developed regime is approximated only deep in the wind farm, after approximately 15 rows of turbines. Our data suggest that for the cases considered in this study, the empirical coefficients that can be used to describe turbulent entrainment and transfers above the wind farm exhibit little dependence on the farm layout and may be considered constant for modelling purposes. However, the flow field within the wind farm layer can be strongly modulated by the turbine density (spacing) as well as the array layout, and to that extent it can be argued that they are both primary factors determining the wind farm power output.

17 WIND ENERGY↗

Small- and Wide-Angle X-ray Scattering Studies of Liquid–Liquid Phase Separation in Silicate Melts

Incongruent liquid-liquid phase separation is a common phenomenon in molten oxides, but there are few structural studies due to the high temperatures involved ca. >1600oC. In this work, we present a high-energy x-ray combined small/wide angle scattering (SAXS/WAXS) method that can directly probe non-equilibrium phase diagrams. The Porod exponent in the SAXS signal is extracted, which measures the roughness of the interface formed between different phases. Problematic volatilization of silica in Al 2 O 3 -, CaO-, and MgO-bearing silica-rich liquids were minimized using levitation, laser heating and rapid time-resolved measurements (lasting tens of seconds), to probe the kinetics of the phase separation process. The WAXS measurement simultaneously probes the local atomic structure of the liquid state and shows that the primary structural changes are associated with the SiO 2 network. Cation coordination numbers extracted from pair distribution functions support the model that the origin of phase separation in binary silicate systems is due to Coulombic repulsions between poorly screened cations. For CaO-SiO 2 , the liquid-liquid phase separation is found to correlate with a pause in the temperature dependent atomic disorder associated with SiO4 tetrahedra.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Soft x-ray spectroscopy of ammonium sulfate aerosols at varied pH conditions

Aqueous aerosols are useful model systems for understanding the physical chemistry that takes place in the Earth’s atmosphere, as well as the chemistry of other solar system objects. Ammonium sulfate aerosols are impacted by anthropogenic sources such as farming and shipping and are understood to be important seeds of cloud nucleation in the atmosphere, affecting climate. X-ray photoelectron spectroscopy and near edge x-ray absorption fine structure spectroscopy were used in tandem to probe the surface and bulk properties of aqueous (NH 4 ) 2 SO 4 , respectively. Aerosolized solutions of (NH 4 ) 2 SO 4 , some altered with NaOH to modify pH, were introduced via an aerodynamic lens to a velocity map imaging instrument for detection. The results show that as pH and sodium cation concentration increase, sulfate anion and ammonia become more prevalent at the surface, and the aerosol surface appears to become drier. However, most of the aerosol remains aqueous, with ion concentrations insensitive to the addition of NaOH. Density functional theory calculations were also performed to probe the coordination environment at the aerosol surfaces to understand the underlying phenomena. Finally, the changes seen on the surface of the aerosol underscore the importance of pH in regulating the structure and chemical properties of atmospherically relevant aerosols.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Measuring the Aerosol Collection Efficiency and Detector Face Deposition of the Bladewerx KatanaGBM™ (Glove Box Monitor) Continuous Air Monitor

To assist Bladewerx LLC (the Requestor) in testing their new CAM (continuous air monitor) sampler model Bladewerx™ KatanaGBM™ (Glove Box Monitor), the Laboratory (LANL, i.e. Los Alamos National Laboratory) measured the aerosol particle collection efficiency and detector face deposition for several experimental test conditions. Bladewerx LLC provided a prototype KatanaGBM with a set of requested tests. According to these parameters, LANL designed and performed a series of experiments to (A.) Measure the aerosol particle collection efficiency and detector face deposition of the KatanaGBM at three air flow rates of 5, 42, and 70 ALPM (ambient liters per minute), (B.) Measure the collection efficiency and detector face deposition using two sizes of oil droplet particles: 3±1 and 10±1 µm (micron) AED (aerodynamic equivalent diameter), and (C.) Test the KatanaGBM for aerosol collection efficiency and detector face deposition with the wind tunnel’s air flow at three different angles 0°, 45° and 90° (compared to the KatanaGBM’s filter face).

61 RADIATION PROTECTION AND DOSIMETRY↗

Aeroacoustic Assessment of Wind Plant Controls

The Aeroacoustic Assessment project aims to quantify changes in aeroacoustic noise generation by a utility scale wind turbine operating under imposed yaw offsets common for wake steering and wind plant control strategies. Active plant control utilizing wake deflection control strategies have been shown experimentally and computationally to reliably produce 1-2% of additional annual energy production (AEP) without significant changes in turbine structural loads, the potential impact on aeroacoustic emissions has yet to be quantified or completely understood. Yawed operation of a wind turbine changes the three-dimensional aerodynamic interaction between the rotor blades and the incoming atmospheric flow, leading to changes in noise generation. This work quantifies the extent to which active control induces additional aeroacoustic emissions from additional separation and other flow interaction dynamic effects. Given public concerns about wind turbine noise and the need for observational data required for regulators to establish noise restrictions, we must understand potential acoustic emissions resulting from active control prior to commercial deployment and the development of practical noise reduction methods and technologies. The work outlined in this report details the new aeroacoustic measurement capability developed at NREL and its application to making full-field observations of noise from a utility-scale wind turbine. Preliminary noise modeling with the aeroacoustics module in OpenFAST helped to establish the design of the experiment, specifically targeting the noise observed at observers distributed around the DOE-owned GE 1.5 MW wind turbine. Low-frequency and infrasound measurement capability implemented in this project establish an operational baseline for the wind turbine, setting the stage for future control, rotor blade, and turbine design research.

17 WIND ENERGY↗

The nonlinear behavior of generic tail fins for small wind turbines

This paper describes analysis and measurements of the yaw response of tail fins for small wind turbines. It is based on an extension of unsteady slender body theory (USBT) to cover non-slender fins and high angles of incidence, both of which make the theory nonlinear. We provide three main additions to the substantial literature on linearized USBT for tail fins. First, USBT is extended to high angles by modeling the nonlinear vortex dynamics. Second, the restriction to slender bodies is removed by modeling the chordwise load variation. Third, we consider the effect of time-varying wind speed. Further, the extended theory is compared to wind tunnel measurements of the yaw behavior of delta, elliptical, and rectangular tail fins without a rotor and nacelle. The fins were released from initial yaw angles of -40° and -80°; the latter is of sufficient magnitude to show the importance of the nonlinear yaw dynamics. Generally good agreement was found between the theory and measurements, and the theory was shown to be more accurate than a “polar” or quasi-steady model which uses only the lift and drag of a delta planform. Of the three planforms, the rectangular one showed the lowest accuracy in terms of frequency but the damping was accurately predicted. Overall, the results demonstrate the importance of nonlinearity in the response of a yawing tail fin, particularly for the higher aspect ratio fins at large yaw angles.

17 WIND ENERGY↗