Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Voltage Angle”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS2010

Fully Printed High-Frequency Phased-Array Antenna on Flexible Substrate

To address the issues of flexible electronics needed for surface-to-surface, surface-to-orbit, and back-to-Earth communications necessary for manned exploration of the Moon, Mars, and beyond, a room-temperature printing process has been developed to create active, phased-array antennas (PAAs) on a flexible Kapton substrate. Field effect transistors (FETs) based on carbon nanotubes (CNTs), with many unique physical properties, were successfully proven feasible for phased-array antenna systems. The carrier mobility of an individual CNT is estimated to be at least 100,000 sq cm/V(dot)s. The CNT network in solution has carrier mobility as high as 46,770 sq cm/V(dot)s, and has a large current-density carrying capacity of approx. 1,000 mA/sq cm , which corresponds to a high carrying power of over 2,000 mW/ sq cm. Such high carrier mobility, and large current carrying capacity, allows the achievement of high-speed (>100 GHz), high-power, flexible electronic circuits that can be monolithically integrated on NASA s active phasedarray antennas for various applications, such as pressurized rovers, pressurized habitats, and spacesuits, as well as for locating beacon towers for lunar surface navigation, which will likely be performed at S-band and attached to a mobile astronaut. A fully printed 2-bit 2-element phasedarray antenna (PAA) working at 5.6 GHz, incorporating the CNT FETs as phase shifters, is demonstrated. The PAA is printed out at room temperature on 100-mm thick Kapton substrate. Four CNT FETs are printed together with microstrip time delay lines to function as a 2-bit phase shifter. The FET switch exhibits a switching speed of 0.2 ns, and works well for a 5.6-GHz RF signal. The operating frequency is measured to be 5.6 GHz, versus the state-of-the-art flexible FET operating frequency of 52 MHz. The source-drain current density is measured to be over 1,000 mA/sq cm, while the conventional organic FETs, and single carbon nanotube-based FETs, are typically in the mA to mA/sq cm range. The switching voltage used is 1.8 V, while the state-of-the-art flexible FET has a gate voltage around 50 V. The gate voltage can effectively control the source-drain current with an ON-OFF ratio of over 1,000 obtained at a low Vds bias of 1.8 V. The azimuth steering angles of PAA are measured at 0deg, -14.5deg, -30deg, and 48.6deg. The measured far-field patterns agree well with simulation results. The efficiency of the 2-bit 2-element PAA is measured to be 39 percent, including the loss of transmission line, FET switch, and coupling loss of RF probes. With further optimization, the efficiency is expected to be around 50-60 percent.

Chen, Yihong↗
DOE OSTI2020

Wetting behaviors of fluoroterpolymer fiber films

Various aspects of electrospun fibers prepared from terpolymer of tetrafluoroethylene (TFE), hexafluoropropylene (HFP), and vinylidene fluoride (VDF) (THV)/acetone solutions at two applied voltages, THV/acetone solutions having Texas montmorillonite with two ratios, and THV/ethyl acetate solutions using two needle sizes are described. Fibers from THV/acetone and THV/ethyl acetate solutions showed shallow indentations and pores, respectively. The clay, functioning as electrospinning agent, did not influence the fiber morphology, but yielded narrower fiber diameter distribution and the thinnest fibers. Heterogeneous fiber diameter distribution and increase in the fiber diameters were observed by lowering the voltage for fibers of THV/acetone solutions. Fibers from THV/ethyl acetate solutions had the largest diameter and the broadest diameter distribution. Electrospun THV fibers having both hydrophobic characteristics with nearly 140° water contact angles and oleophilic properties with oil contact angles less than 45° might have applications in areas such as water/oil separation.

02 PETROLEUM↗
DOE OSTI2026

Collaborative R&D with REEL Solar Inc (REEL) to Understand and Overcome Performance Limitations in CdTe Solar Cells: Cooperative Research and Development (Final Report)

This CRADA will focus on processing, advanced characterization, and testing of photovoltaic materials and devices to understand and improve REEL CdTe solar technology. This will include examining process variations and different buffer, absorber, and contact layers from REEL and NLR to maximize performance. The unique and diverse advanced characterization tools at NLR, such as time-resolved photoluminescence, capacitance-voltage measurements, electron beam scattered diffraction, cathodoluminescence, electron microscopy, TOF-SIMS, and other measurements will be applied to characterize REEL processing to improve understanding and guide experimental directions. Accelerated stability and potential induced degradation tests will be used to analyze metastability, short-and-long term degradation, and improve bankability. A second and major thrust this period will be joint development of Si/CdTe tandem solar cells to overcome industry wide terrestrial solar efficiency limits with the two lowest cost and manufacturable solar materials today. This will include developing novel transparent back contacts that can be incorporated into tandem structures and other novel solar applications, detailed analysis of designs and configurations for CdTe/Si tandem modules, and prototyping REEL CdTe Technology with Si bottom cells in tandem structures.

14 SOLAR ENERGY↗
NASA NTRS1973

The electric potential of the lunar surface

Acceleration and detection of the lunar thermal ionosphere in the presence of the lunar electric field yields a value of at least +10 V for the lunar electric potential for solar zenith angles between approximately 20 and 45 deg and in the magnetosheath or solar wind. An enhanced positive ion flux is observed with the ALSEP Suprathermal Ion Detector when a pre-acceleration voltage attains certain values. This enhancement is greater when the moon is in the solar wind as opposed to the magnetosheath.

Fenner, M. A.↗
NASA NTRS1993

Optical response of an ultrathin film and a large-angle grain-boundary in superconducting YBa2Cu3O(7-delta)

We have investigated the optical response of epitaxial ultrathin (3 nm) YBa2Cu3O(7-delta) film on an NdGaO3 substrate and thin (50 nm) film of YBa2Cu3O(7-delta) on a bicrystal SrTiO3 substrate. While the current-voltage characteristics of the ultrathin film indicate a Kosterlitz-Thouless transition (associated with vortex-antivortex unbinding) at a temperature T(KT), we do not observe any optical response at or below T(KT). An enhanced optical response with nonbolometric characteristics was observed from the grain-boundary as compared to the bolometric optical response of the epitaxial film at the resistive transition. These results indicate that the grain-boundary weak links play a significant role in the enhanced optical response near Tc.

Bhattacharya, S.↗
NASA NTRS2019

Dust Abrasion Damage on Martian Solar Arrays: Experimental Investigation and Opportunity Rover Performance Analysis

Here we investigate the effects of erosion and weathering that occur on III-V cover-glass interconnected cells (CICs) after exposure to Mars dust storm conditions. The durability of these materials in a Martian environment is not well characterized so we perform analogous experimentation. To replicate the dust impingement, test coupons were placed in an enclosure and sandblasted with Mars dust simulant. We show the J-V response dependency on both incident angle and exposure times. We find that the simulated Martian dust storm often results in damage to the anti-reflective coating and subsequent reduced short circuit current. Reduction in the open circuit voltage is observed, likely caused by structural damage to the crystal lattice after CIC fracture. We employ data-driven modeling to determine a performance degradation rate that is consistent with zero within uncertainty. We also quantify the soiling contribution and power degradation of the photovoltaic cells on Mars through analysis of 4.95 Martian years of report-out power conditions from the Opportunity rover. We find that atmospheric dust suspended due to a weather event does not result in instantaneous settled dust on the PV cells. We calculate via autocorrelation function that the dust settling rate is approximately 21 Sols from atmospheric dust suspension. The findings presented here deliver a realistic approximation for the insolation values and subsequent PV power expected over time on the Martian surface thus informing future dust abatement systems.

McMillon-Brown, Lyndsey↗
NASA NTRS2019

Dust Abrasion Damage on Martian Solar Arrays: Experimental Investigation and Opportunity Rover Performance Analysis

Here we investigate the effects of erosion and weathering that occur on III-V cover-glass interconnected cells (CICs) after exposure to Mars dust storm conditions. The durability of these materials in a Martian environment is not well characterized so we perform analogous experimentation. To replicate the dust impingement, test coupons were placed in an enclosure and sandblasted with Mars dust simulant. We show the J-V response dependency on both incident angle and exposure times. We find that the simulated Martian dust storm often results in damage to the anti-reflective coating and subsequent reduced short circuit current. Reduction in the open circuit voltage is observed, likely caused by structural damage to the crystal lattice after CIC fracture. We employ data-driven modeling to determine a performance degradation rate that is consistent with zero within uncertainty. We also quantify the soiling contribution and power degradation of the photovoltaic cells on Mars through analysis of 4.95 Martian years of report-out power conditions from the Opportunity rover. We find that atmospheric dust suspended due to a weather event does not result in instantaneous settled dust on the PV cells. We calculate via autocorrelation function that the dust settling rate is approximately 21 Sols from atmospheric dust suspension. The findings presented here deliver a realistic approximation for the insolation values and subsequent PV power expected over time on the Martian surface thus informing future dust abatement systems.

McMillon-Brown, Lyndsey↗
DOE OSTI2025

Discovery of an Intrinsic Antiferromagnetic Semiconductor EuSc 2 Te 4 With Magnetism‐Driven Nonlinear Transport

Magnetic topological materials have recently emerged as a promising platform for studying quantum geometry by the nonlinear transport in thin film devices. In this work, an antiferromagnetic (AFM) semiconductor EuSc₂Te₄ as the first bulk crystal that exhibits quantum geometry-driven nonlinear transport is reported. This material crystallizes into an orthorhombic lattice with AFM order below 5.2 K and a bandgap of less than 50 meV. The calculated band structure aligns with the angle-resolved photoemission spectroscopy spectrum. The AFM order preserves combined space-time inversion symmetry but breaks both spatial inversion and time-reversal symmetry, leading to the nonlinear Hall effect (NLHE). Nonlinear Hall voltage measured in bulk crystals appears at zero field, peaks near the spin-flop transition as the field increases, and then diminishes as the spin moments align into a ferromagnetic order. This field dependence, along with the scaling analysis of the nonlinear Hall conductivity, suggests that the NLHE of EuSc₂Te₄ involves contributions from quantum metric, in addition to extrinsic contributions, such as spin scattering and junction effects. Furthermore, this NLHE is found to have the functionality of broadband frequency mixing, indicating its potential applications in electronics. This work reveals a new avenue for studying magnetism-induced nonlinear transport in magnetic materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Conductive Thin Films over Large Areas by Supramolecular Self-Assembly

We report a “one-step” method for preparing conductive thin films with cylindrical microdomains oriented normal to the surface over large areas using the supramolecular assembly of poly(styrene-block-4-vinylpyridine) (PS19-b-P4VP 5 ) and 5,10,15,20-tetrakis(4-hydroxyphenyl)-21H,23H-porphine (HOTPP). HOTPP interacts with the P4VP block by hydrogen bonding between the hydroxyl group of HOTPP and pyridine ring of PS 19 -b-P4VP 5 , forming cylindrical P4VP(HOTPP) domains having an average diameter of ~17 nm in a PS matrix. Here, dynamic light scattering, contact angle, and in situ grazing incidence small-angle X-ray scattering measurements show a morphological transition from spherical micelles in solution to cylindrical microdomains oriented normal to the substrate surface during the drying process. From the dependence of current on voltage, an average current of ~4.0 nA is found to pass through a single microdomain, pointing to a promising route for organic semiconductor device applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Grid-Forming Control Using TAPAS Software Defined Inverters

Here, this paper discusses the design and hardware implementation aspects of state-feedback primary control for grid forming inverters. The primary control consists of two tracking control laws: voltage tracking and frequency/angle tracking. The voltage tracking control requires voltage and current at the inverter's switch terminal (i.e. before the filter). The fundamental component of switch terminal voltage is estimated using the inverter's average model while the switch terminal current is estimated using an observer, thus obviating the need for sensors at the switch terminals. The measurements of frequency and angle(s) needed for frequency/angle tracking are noisy due to measurement noises and inherent delays in the phase locked loop (PLL). Conditioning of these feedback signals is discussed in detail, and the corresponding changes in the control design are provided to better attenuate the impact of noises. Effectiveness of the proposed design and implementation is demonstrated by the implementation results from TAPAS software defined inverter (SDI).

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2021

Quantifying the chemical, electrochemical heterogeneity and spatial distribution of (poly) sulfide species using Operando SANS

In-situ and operando measurements are done to gain a better understanding of the precipitation mechanisms during charge and discharge in lithium sulfur batteries. A carbon felt networked with microfibers consisting of pores, 2 nm and smaller, is used as a freestanding sulfur host. Three different methods of sulfur infiltration are explored in order to determine the best one to fill most of the pores. It was identified to be a melt infiltration method in a vacuum oven, where the pores including the ultra-micropores, are successfully filled. In-situ electrochemical impedance spectroscopy measurements show a solid product formation occurring at the sulfur cathode, both during the high voltage plateau and at the end of discharge. In a 3-electrode EIS measurement, a similar solid product formation on the Li counter electrode due to its reaction with polysulfides is also observed. Operando small angle neutron scattering measurements show the solid product formation, in the carbon, both near the beginning and at the end of discharge, confirming the precipitation data via contrast changes as a function of charge and discharge. It is shown that Li 2 S precipitates in the pores at the beginning and the end of discharge, whereas S8 precipitates on the surface of the carbon felt. Finally, this lithium sulfur system shows both the quasi-solid-state and the solid-liquid-solid reactions in a typical ethereal electrolyte solution with a two-plateau discharge profile.

25 ENERGY STORAGE↗
DOE OSTI2022

Progress in Modeling the 2019 Extended Magnetically Insulated Transmission Line (MITL) and Courtyard Environment Trial at HERMES-III

This report documents the progress made in simulating the HERMES-III Magnetically Insulated Transmission Line (MITL) and courtyard with EMPIRE and ITS. This study focuses on the shots that were taken during the months of June and July of 2019 performed with the new MITL extension. There were a few shots where there was dose mapping of the courtyard, 11132, 11133, 11134, 11135, 11136, and 11146. This report focuses on these shots because there was full data return from the MITL electrical diagnostics and the radiation dose sensors in the courtyard. The comparison starts with improving the processing of the incoming voltage into the EMPIRE simulation from the experiment. The currents are then compared at several location along the MITL. The simulation results of the electrons impacting the anode are shown. The electron impact energy and angle is then handed off to ITS which calculates the dose on the faceplate and locations in the courtyard and they are compared to experimental measurements. ITS also calculates the photons and electrons that are injected into the courtyard, these quantities are then used by EMPIRE to calculated the photon and electron transport in the courtyard. The details for the algorithms used to perform the courtyard simulations are presented as well as qualitative comparisons of the electric field, magnetic field, and the conductivity in the courtyard. Because of the computational burden of these calculations the pressure was reduce in the courtyard to reduce the computational load. The computation performance is presented along with suggestion on how to improve both the computational performance as well as the algorithmic performance. Some of the algorithmic changed would reduce the accuracy of the models and detail comparison of these changes are left for a future study. As well as, list of code improvements there is also a list of suggested experimental improvements to improve the quality of the data return.

47 OTHER INSTRUMENTATION↗
NASA NTRS1973

Electric potential of the moon in the solar wind.

Acceleration and detection of the lunar thermal ionosphere in the presence of the lunar electric field yields a value of at least +10 V for the lunar electric potential for solar zenith angles between approximately 20 and 45 deg and in the magnetosheath or solar wind. An enhanced positive ion flux is observed with the Apollo Lunar Surface Experiments Package Suprathermal Ion Detector Experiment when a preacceleration voltage attains certain values. This enhancement is greater when the moon is in the solar wind as opposed to the magnetosheath.

Freeman, J. W., Jr.↗
DOE OSTI2026

Experimental study of ECH pre-ionization on J-TEXT

An experimental study on electron cyclotron heating (ECH) pre-ionization has been conducted on J-TEXT in support of the joint experiment research for ITER plasma initiation. In this experiment, ECH power was injected to the vessel before the application of loop voltage ionize the neutral gas and form the initial plasma or so-called pre-plasma. The impact of several significant factors, such as magnetic field configuration, pre-fill gas pressure, ECH toroidal injection angle and ECH power on the evolution of pre-plasma are systematically studied, aiming to identify shared features, clarify their potential relationship and optimize the discharge parameters to generate a rather high pre-plasma density. By separating ECH power from the inductive start-up, the effect of pre-plasma on tokamak start-up can be observed. A dynamic magnetic configuration facilitates the transition of pre-plasma to tokamak plasma. To assess the influence of pre-plasma density on tokamak start-up, two kinds of magnetic field configurations are examined. While the effect of different pre-plasma densities on tokamak start-up is negligible, a significant difference is observed between pure ohmic start-up and start-up with pre-ionization. The studies presented here show evolutionary trends and threshold values needed to optimize ECH pre-ionization and also a feasible way to improve pre-plasma density and a configuration to stabilize pre-plasma for transition. Eventually, these results may contribute to multi-machine research and physics analysis that can assist ITER with its optimal preparation for first plasma operation.

ECH↗
NASA NTRS1975

The 15 cm mercury ion thruster research 1975

Doubly charged ion current measurements in the beam of a SERT II thruster are shown to introduce corrections which bring its calculated thrust into close agreement with that measured during flight testing. A theoretical model of doubly charged ion production and loss in mercury electron bombardment thrusters is discussed and is shown to yield doubly-to-singly charged ion density ratios that agree with experimental measurements obtained on a 15 cm diameter thruster over a range of operating conditions. Single cusp magnetic field thruster operation is discussed and measured ion beam profiles, performance data, doubly charged ion densities, and discharge plasma characteristics are presented for a range of operating conditions and thruster geometries. Variations in the characteristics of this thruster are compared to those observed in the divergent field thruster and the cusped field thruster is shown to yield flatter ion beam profiles at about the same discharge power and propellant utilization operating point. An ion optics test program is described and the measured effects of grid system dimensions on ion beamlet half angle and diameter are examined. The effectiveness of hollow cathode startup using a thermionically emitting filament within the cathode is examined over a range of mercury flow rates and compared to results obtained with a high voltage tickler startup technique. Results of cathode plasma property measurement tests conducted within the cathode are presented.

Wilbur, P. J.↗
DOE OSTI2022

Constant-potential molecular dynamics simulations of molten salt double layers for FLiBe and FLiNaK

We report the results of constant-potential molecular dynamics simulations of the double layer interface between molten 2LiF–BeF 2 (FLiBe) and 23LiF–6NaF–21KF (FLiNaK) fluoride mixtures and idealized solid electrodes. Employing methods similar to those used in studies of chloride double layers, we compute the structure and differential capacitance of molten fluoride electric double layers as a function of applied voltage. The role of molten salt structure is probed through comparisons between FLiBe and FLiNaK, which serve as models for strong and weak associate-forming salts, respectively. In FLiBe, screening involves changes in Be–F–Be angles and alignment of the oligomers parallel to the electrode, while in FLiNaK, the electric field is screened mainly by rearrangement of individual ions, predominantly the polarizable potassium cation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Studies of EC pre-ionization in DIII-D to support development of ITER plasma initiation

New experiments have been conducted at DIII-D to improve the physics understanding of plasma initiation assisted by electron cyclotron (EC) wave injection, allowing better extrapolation to ITER. This has been achieved by applying an EC pulse prior to start of the inductive plasma initiation (i.e. the generation of a loop voltage). A pre-plasma was formed during the EC pulse that was characterized in terms of the maximum density and temperature. Parametric scans were performed to study the influence of the EC injected power, EC injection angle, and pre-fill gas pressure on the pre-plasma creation process. These experiments showed that pre-ionized plasma of good quality can have a significant effect on the subsequent V loop induced plasma initiation process, i.e. a high density pre-plasma, increases the plasma current rise and speed at which ionization is achieved when the V loop is applied. Here, a good quality pre-plasma is one that achieved a significant degree of ionization, mainly obtained by providing sufficient ECH power in DIII-D of the order of 1 MW. It was found that a minimum EC power of 0.5 MW was required in DIII-D to create ionization, and this would scale to a minimum power of roughly 6.5 MW for ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2011

Higher Order Mode Coupling in Feed Waveguide of a Planar Slot Array Antenna

A simple technique was developed to account for the higher order mode coupling between adjacent coupling slots in the feed waveguide of a planar slot array. The method uses an equation relating the slot impedance to the slot voltage and a reaction integral involving the equivalent magnetic current of the slot aperture and the magnetic field coupled from an adjacent slot. In the proposed method, one uses the Elliott s design technique to determine tilt angles and lengths of the coupling slots. The radiating slots are modeled as shunt admittances, and the coupling slots are modeled as series impedances.

Rengarajan, Sembiam↗