Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Thrust Load”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1961

Loads Induced on a Flat-Plate Wing by an Air Jet Exhausting Perpendicularly through the Wing and Normal to a Free-Stream Flow of Mach Number 2.0

Measurements were made of loads induced on a flat-plate wing by an air jet exhausting perpendicularly through the wing and normal to the free-stream flow.The investigation was conducted at a free-stream Mach number of 2.0 and a Reynolds number per foot of 14.4 x 10(exp 6). An axially symmetric sonic nozzle and two supersonic nozzles were employed for the jets. The supersonic nozzles consisted of an axially symmetric nozzle with exit Mach number of 3.44 and a two-dimensional nozzle with exit Mach number of 1.76. The ratio of nozzle total pressure to free-stream static pressure was varied from 20 to 110. Negative loads were induced on the flat-plate wing by all the jets. As the nozzle pressure ratio was increased the magnitude of interference loads due to jet thrust decreased. The chordwise center-of-pressure location generally moved toward the nozzle center line as the pressure ratio was increased.

Janos, Joseph J.↗
NASA NTRS1991

Viscoplastic analysis of an experimental cylindrical thrust chamber liner

A viscoplastic stress-strain analysis of an experimental cylindrical thrust chamber is presented. A viscoelastic constitutive model incorporating a single internal state variable that represents kinematic hardening was employed to investigate whether such a viscoplastic model could predict the experimentally observed behavior of the thrust chamber. Two types of loading cycles were considered: a short cycle of 3.5 sec. duration that corresponded to the experiments, and an extended loading cycle of 485.1 sec. duration that is typical of the Space Shuttle Main Engine (SSME) operating cycle. The analysis qualitatively replicated the deformation behavior of the component as observed in experiments designed to simulate SSME operating conditions. The analysis also showed that the mode and location in the component may depend on the loading cycle. The results indicate that using viscoplastic models for structural analysis can lead to a more realistic life assessment of thrust chambers.

Arya, Vinod K.↗
NASA NTRS1992

Viscoplastic analysis of an experimental cylindrical thrust chamber liner

A viscoplastic stress-strain analysis of an experimental cylindrical thrust chamber is presented. A viscoelastic constitutive model incorporating a single internal state variable that represents kinematic hardening was employed to investigate whether such a viscoplastic model could predict the experimentally observed behavior of the thrust chamber. Two types of loading cycles were considered: a short cycle of 3.5-s duration that corresponded to the experiments, and an extended loading cycle of 485.1 s duration that is typical of the Space Shuttle Main Engine (SSME) operating cycle. The analysis qualitatively replicated the deformation behavior of the component as observed in experiments designed to simulate SSME operating conditions. The analysis also showed that the mode and location of failure in the component may depend on the loading cycle. The results indicate that using viscoplastic models for structural analysis can lead to a more realistic life assessment of thrust chambers.

Arya, Vinod K.↗
NASA NTRS1985

Structural and mechanical design challenges of space shuttle solid rocket boosters separation and recovery subsystems

The design of the space shuttle solid rocket booster (SRB) subsystems for reuse posed some unique and challenging design considerations. The separation of the SRBs from the cluster (orbiter and external tank) at 150,000 ft when the orbiter engines are running at full thrust meant the two SRBs had to have positive separation forces pushing them away. At the same instant, the large attachments that had reacted launch loads of 7.5 million pounds thrust had to be servered. These design considerations dictated the design requirements for the pyrotechnics and separation rocket motors. The recovery and reuse of the two SRBs meant they had to be safely lowered to the ocean, remain afloat, and be owed back to shore. In general, both the pyrotechnic and recovery subsystems have met or exceeded design requirements. In twelve vehicles, there has only been one instance where the pyrotechnic system has failed to function properly.

Woodis, W. R.↗
NASA NTRS1985

An analysis of cross-coupling of a multicomponent jet engine test stand using finite element modeling techniques

A two axis thrust measuring system was analyzed by using a finite a element computer program to determine the sensitivities of the thrust vectoring nozzle system to misalignment of the load cells and applied loads, and the stiffness of the structural members. Three models were evaluated: (1) the basic measuring element and its internal calibration load cells; (2) the basic measuring element and its external load calibration equipment; and (3) the basic measuring element, external calibration load frame and the altitude facility support structure. Alignment of calibration loads was the greatest source of error for multiaxis thrust measuring systems. Uniform increases or decreases in stiffness of the members, which might be caused by the selection of the materials, have little effect on the accuracy of the measurements. It is found that the POLO-FINITE program is a viable tool for designing and analyzing multiaxis thrust measurement systems. The response of the test stand to step inputs that might be encountered with thrust vectoring tests was determined. The dynamic analysis show a potential problem for measuring the dynamic response characteristics of thrust vectoring systems because of the inherently light damping of the test stand.

Schweikhard, W. G.↗
NASA NTRS2008

Engineering Models Ease and Speed Prototyping

NASA astronauts plan to return to the Moon as early as 2015 and establish a lunar base, from which 6-month flights to Mars would be launched by 2030. Essential to this plan is the Ares launch vehicle, NASA s next-generation spacecraft that will, in various iterations, be responsible for transporting all equipment and personnel to the Moon, Mars, and beyond for the foreseeable future. The Ares launch vehicle is powered by the J-2X propulsion system, with what will be the world s largest rocket nozzles. One of the conditions that engineers carefully consider in designing rocket nozzles particularly large ones is called separation phenomenon, which occurs when outside ambient air is sucked into the nozzle rim by the relatively low pressures of rapidly expanding exhaust gasses. This separation of exhaust gasses from the side-wall imparts large asymmetric transverse loads on the nozzle, deforming the shape and thus perturbing exhaust flow to cause even greater separation. The resulting interaction can potentially crack the nozzle or break actuator arms that control thrust direction. Side-wall loads are extremely difficult to measure directly, and, until now, techniques were not available for accurately predicting the magnitude and frequency of the loads. NASA researchers studied separation phenomenon in scale-model rocket nozzles, seeking to use measured vibration on these nozzle replicas to calculate the unknown force causing the vibrations. Key to this approach was the creation of a computer model accurately representing the nozzle as well as the test cell.

Source record↗
NASA NTRS2009

Liquid Oxygen/Liquid Methane Test Summary of the RS-18 Lunar Ascent Engine at Simulated Altitude Conditions at NASA White Sands Test Facility

Tests were conducted with the RS18 rocket engine using liquid oxygen (LO2) and liquid methane (LCH4) propellants under simulated altitude conditions at NASA Johnson Space Center White Sands Test Facility (WSTF). This project is part of NASA s Propulsion and Cryogenics Advanced Development (PCAD) project. "Green" propellants, such as LO2/LCH4, offer savings in both performance and safety over equivalently sized hypergolic propellant systems in spacecraft applications such as ascent engines or service module engines. Altitude simulation was achieved using the WSTF Large Altitude Simulation System, which provided altitude conditions equivalent up to approx.120,000 ft (approx.37 km). For specific impulse calculations, engine thrust and propellant mass flow rates were measured. Propellant flow rate was measured using a coriolis-style mass-flow meter and compared with a serial turbine-style flow meter. Results showed a significant performance measurement difference during ignition startup. LO2 flow ranged from 5.9-9.5 lbm/sec (2.7-4.3 kg/sec), and LCH4 flow varied from 3.0-4.4 lbm/sec (1.4-2.0 kg/sec) during the RS-18 hot-fire test series. Thrust was measured using three load cells in parallel. Ignition was demonstrated using a gaseous oxygen/methane spark torch igniter. Data was obtained at multiple chamber pressures, and calculations were performed for specific impulse, C* combustion efficiency, and thrust vector alignment. Test objectives for the RS-18 project are 1) conduct a shakedown of the test stand for LO2/methane lunar ascent engines, 2) obtain vacuum ignition data for the torch and pyrotechnic igniters, and 3) obtain nozzle kinetics data to anchor two-dimensional kinetics codes.

Melcher, John C., IV↗
NASA NTRS1993

Parachute Swivel Mechanism for planetary entry

A parachute swivel mechanism (PSM) for planetary entry missions such as a Mars probe (MARSNET) or return of cometary material samples (ROSETTA mission) has been developed. The purpose of the PSM is to decouple the spin of the probe from the parachute, with low friction torque, during both the deployment and descent phases. Critical requirements are high shock loads, low friction, low temperatures, and several years of storage in the deep space environment (during the cruise phase of the probe, prior to operation). The design uses a main thrust ball bearing to cope with the load requirement and a smaller thrust ball bearing for guiding of the shaft. Except for use on the Viking and Galileo swivels, it appears that this type of bearing has very rarely been employed in space mechanisms, so that little is known of its friction behavior with dry lubrication. A slip ring assembly allows the transfer of electrical power for post-reefing of the parachute. A test program has been conducted covering the environmental conditions of Mars entry and Earth reentry. This paper describes requirement constraints, model missions of planetary entries, a bearing trade-off, analyses performed, design details, the lubrication system, and test results (friction torque versus load/spin rate). In addition, the design of the test rig is addressed.

Birner, R.↗
NASA NTRS1992

Thrust stand evaluation of engine performance improvement algorithms in an F-15 airplane

Results are presented from the evaluation of the performance seeking control (PSC) optimization algorithm developed by Smith et al. (1990) for F-15 aircraft, which optimizes the quasi-steady-state performance of an F100 derivative turbofan engine for several modes of operation. The PSC algorithm uses onboard software engine model that calculates thrust, stall margin, and other unmeasured variables for use in the optimization. Comparisons are presented between the load cell measurements, PSC onboard model thrust calculations, and posttest state variable model computations. Actual performance improvements using the PSC algorithm are presented for its various modes. The results of using PSC algorithm are compared with similar test case results using the HIDEC algorithm.

Conners, Timothy R.↗
NASA NTRS1985

Portable 90 degree proof loading device

A hydraulically actuated device is described for applying a test load to a bearing or the like to prove the integrity of its mounting or staking within a bore in a housing such as gear case. To accommodate limited access situations, the device is constructed in a right angle configuration in which a hydraulic cylinder applies axial pressure to a first thrust rod assemly which includes a first thrust rod through a threated spindle driving a linearly translated cam. Cam follower wheel transfers the translation to a second thrust rod assembly which includes a horizontal shaft and a spindle within a cross-arm housing portion and a tubular housing portion. The same second thrust direction applies the bearing loading in either of two directions depending upon the shape of the interface parts. The interface parts can bear on the bearing from either side with respect to the bearing mounting structural part.

Bird, R. G.↗
NASA NTRS1983

Progress in propulsion system/airframe structural integration

Attention is given to the improvements in mathematical modeling, and the emerging role of computer-related technology, in airframe structural technology advancements related to the engine/airframe integration requirements of such recent designs as the 747 airliner's JT9D turbofan engine nacelle. Also noted are investigation results concerning propulsion system flight loads and their influence on thrust-specific fuel consumption deterioration, which has been addressed through the development of the novel structural concept of the 'load-carrying core cowl' engine nacelle structure. Analytical studies on integrated system vibration include low frequency, nonsynchronous vibration analyses of large, high bypass turbofan engines that have been conducted by means of three-dimensional integrated finite element models.

White, J. L.↗
NASA NTRS1980

Estimation of wing nonlinear aerodynamic characteristics at supersonic speeds

A computational system for estimation of nonlinear aerodynamic characteristics of wings at supersonic speeds was developed and was incorporated in a computer program. This corrected linearized theory method accounts for nonlinearities in the variation of basic pressure loadings with local surface slopes, predicts the degree of attainment of theoretical leading edge thrust, and provides an estimate of detached leading edge vortex loadings that result when the theoretical thrust forces are not fully realized.

Carlson, H. W.↗
NASA NTRS2019

SmallSat missions enabled by paired low-thrust hybrid rocket and low-power long-life Hall thruster

The capabilities of a SmallSat-class spacecraft targeting the outer solar system and using a combined chemical and electric propulsion system are explored. The development of compact hybrid rockets has enabled high-thrust engines to be packaged tightly enough to fit on cubesat and SmallSat spacecraft. These hybrid rockets provide 10’s-100 N of thrust depending on the propellant load & >300 s of specific impulse and have been demonstrated in both ambient and vacuum environments. Advancements in low-power long-life Hall thruster technologies have provided the potential for significantly greater propellant throughputs, enabling their use as a primary propulsion element on interplanetary spacecraft. In a recent characterization test campaign, the MaSMi-DM Hall thruster demonstrated power throttling from 150 – 1000 W with >1500 s of specific impulse available at >500 W and >40% total thrust efficiency available at >300 W; peak values of 1940 s and 53% were observed. A notional low-mass spacecraft employing a combined hybrid rocket and low-power electric propulsion system was designed and used for mission concept analysis targeting the outer solar system. Using an imposed wet mass limit of 400 kg, mission trajectories to Saturn and Uranus were generated. Orbit capture with >40% of the launch mass was shown to be possible at either target, with mission transfer times of 7.5 years and 13.5 years for Saturn and Uranus, respectively. Significant follow-on mission activities near Saturn (e.g. to Titan & Enceladus) were also possible by carrying extra propellant mass while remaining under the total wet mass limit.

Karp, Ashley C.↗
NASA NTRS1986

Aerodynamic Loads Induced by a Rotor on a Body of Revolution

A wind-tunnel investigation was conducted in which aerodynamic loads were measured on a small-scale helicopter rotor and a body of revolution located close to it as an idealized model of a fuselage. The objective was to study the aerodynamic interactions as a function of forward speed, rotor thrust, and rotor/body position. Results show that body loads, normalized by rotor thrust, are functions of the ratio between free-stream velocity and the hover-induced velocity predicted by momentum theory.

Smith, Charles A.↗
NASA NTRSDate not supplied

Aeroacoustic Characterization of Optimum Hovering Rotors using Artificial Neural Networks

This work illustrates the use of artificial neural network modeling in the aerodynamic and aeroacoustic characterization of optimum hovering rotors over a broad range of design and operating conditions. Design of Experiments was used to create input feature spaces over eight input factors: the number of rotor blades, rotor radius, rotor rotation rate, design thrust condition, collective pitch, airfoil camber, the location of maximum camber, and the airfoil thickness. A low-fidelity tool chain was then used at the discrete data points defined by the designed input feature spaces to analytically design optimum hovering rotors and simulate aerodynamic and aeroacoustic quantities. This allowed for the generation of data sets over which to train and test the artificial neural network prediction models. Prediction models were trained over the data sets for the actual thrust generated by the rotor, power loading, tonal thickness and loading noise at the fundamental blade passage frequency, and broadband self-noise at seventeen one-third octave bands between 1 kHz and 40 kHz. These prediction models were validated by testing over data previously unseen by the models to quantify their capability for generalization to new data within the design feature space. The models were then used to study the effect each input feature had on the aeroacoustics and aerodynamics of optimum hovering rotors and physical insights were concluded to further explain the effect of each input. This characterization study showed that tonal noise and power loading were most sensitive to the number of rotor blades and the rotor rotation rate and that broadband noise was most sensitive to collective pitch and the design thrust condition.

Christopher S Thurman↗
NASA NTRS1996

Magnetic docking aid for orbiter to ISS docking

The present docking system for the Orbiter uses mechanical capture latches that are actuated by contact forces. The forces are generated when the two approaching masses collide at the docking mechanism. There is always a trade-off between having high enough momentum to effect capture and low enough momentum to avoid structural overload or unacceptable angular displacements. The use of the present docking system includes a contact thrusting maneuver that causes high docking loads to be included into Space Station. A magnetic docking aid has been developed to reduce the load s during docking. The magnetic docking aid is comprised of two extendible booms that are attached adjacent to the docking structure with electromagnets attached on the end of the boom. On the mating vehicle, two steel plates are attached. As the Orbiter approaches Space Station, the booms are extended, and the magnets attach to the actuated (without thrusting), by slowly driving the extendible booms to the stowed position, thus reacting the load into the booms. This results in a docking event that has lower loads induced into Space Station structure. This method also greatly simplifies the Station berthing tasks, since the Shuttle Remote Manipulation System (SRMS) arm need only place the element to be berthed on the magnets (no load required), rather than firing the Reaction Control System (RCS) jets to provide the required force for capture latch actuation. The Magnetic Docking Aid was development testing on a six degree-of-freedom (6 DOF) system at JSC.

Schneider, William C.↗
NASA NTRS1972

Mission analysis for design of a SEP multi-mission spacecraft.

Study of the multimission capability of a solar electric propulsion spacecraft. The study includes such factors as spacecraft constraints, payload variations with launch opportunity, propellant on-loading and off-loading requirements, and limitations in thrusting time, throttling range and steering. The study determined that a single spacecraft design, with P sub zero = 12 kW and I sub s = 3000 sec launched by a Titan IIIC or Titan IIID/Centaur can be used to conduct at least five diverse missions: Eros rendezvous, 1 AU out-of-ecliptic, Mercury orbiter, Jupiter flyby/probe, and Jupiter orbiter. Flight time and injection velocity vary as needed to achieve the desired payload capability. The mission analysis approach and results are presented.

Driver, J. M.↗
NASA NTRS1973

Apollo experience report: Descent propulsion system

The propulsion system for the descent stage of the lunar module was designed to provide thrust to transfer the fully loaded lunar module with two crewmen from the lunar parking orbit to the lunar surface. A history of the development of this system is presented. Development was accomplished primarily by ground testing of individual components and by testing the integrated system. Unique features of the descent propulsion system were the deep throttling capability and the use of a lightweight cryogenic helium pressurization system.

Hammock, W. R., Jr.↗